Re: Driver via ac97 sound problem (VT82C686) Compaq Presario 700

mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed

* Re: Driver via ac97 sound problem (VT82C686) Compaq Presario 700
       [not found]             ` <1011137857.504.16.camel@raul>
@ 2002-01-17  7:48               ` Raul Sanchez Sanchez
  2002-01-17 21:06                 ` salvador
  0 siblings, 1 reply; 2+ messages in thread
From: Raul Sanchez Sanchez @ 2002-01-17  7:48 UTC (permalink / raw)
  To: salvador
  Cc: Paul Lorenz, Jeremy Lumbroso, ignacio, rubio, Jorge Carminati,
	linux-kernel

Hi:


	All the problems i tell you occurs when i try to access to register in
via_card_init_proc. If i try to do this in 1886 initialization (
ac97_codec.c ) i haven't got any problem, i can write the registers of
the 1886 and i can read then perfectly.

	But my question is, later i set up 1886 chip, does via inicialization
change my configuration of it? If i try to print all the register of the
1886 in via_card_init_proc it fails :( and i can't be sure that via code
doesn't change them.


my 1886_setup proc is now as this:


static int setup_ad1886(struct ac97_codec * codec)
{
 int cnt;
 /* The spec says not to mess with other bits unless
 S/PDIF is turned *off* in reg 2A */
 //codec->codec_write(codec, AC97_EXTENDED_STATUS, 0);
 /* The 1886 spec dated 08/25/00 says default value=0
 but ac97 2.2 says it should be 0x2000. */
// codec->codec_write(codec, AC97_RESERVED_3A, 0x0000); /* 48 kHz */
codec->codec_write(codec, 0x0002, 0x003f);
codec->codec_write(codec, 0x0004, 0x003f);
codec->codec_write(codec, 0x0006, 0x003f);
codec->codec_write(codec, 0x000a, 0x003f);
codec->codec_write(codec, 0x000c, 0x003f);
codec->codec_write(codec, 0x000e, 0x003f);
codec->codec_write(codec, 0x0010, 0x0808);
codec->codec_write(codec, 0x0012, 0x083f);
codec->codec_write(codec, 0x0014, 0x0808);
codec->codec_write(codec, 0x0016, 0x0808);
codec->codec_write(codec, 0x0016, 0x0808);
codec->codec_write(codec, 0x0018, 0x0808);
codec->codec_write(codec, 0x001a, 0x0000);
codec->codec_write(codec, 0x001c, 0x0800);
codec->codec_write(codec, 0x0020, 0x0000);
codec->codec_write(codec, 0x0022, 0x000f);
codec->codec_write(codec, 0x0028, 0x0005);
codec->codec_write(codec, 0x002c, 0xbb80);
codec->codec_write(codec, 0x007a, 0xbb80);
codec->codec_write(codec, 0x0032, 0xbb80);
codec->codec_write(codec, 0x0078, 0xbb80);
codec->codec_write(codec, 0x003a, 0x0000);
codec->codec_write(codec, 0x0072, 0x0000);
codec->codec_write(codec, AC97_EXTENDED_STATUS, 1);
codec->codec_write(codec, AC97_RESERVED_3A, 0x2000); /* 48 kHz */
        for (cnt=0; cnt <= 0x7e; cnt = cnt +2)
                printk(KERN_INFO "reg:0x%02x  val:0x%04x\n", cnt,
codec->codec_read(codec, cnt));

 return 0;
 }


and the output in /var/log/messages is:


Jan 16 21:05:38 raul kernel:  INICIALIZANDO MIXER -----
Jan 16 21:05:38 raul kernel: reg:0x00  val:0x0410
Jan 16 21:05:38 raul kernel: reg:0x02  val:0x003f
Jan 16 21:05:38 raul kernel: reg:0x04  val:0x003f
Jan 16 21:05:38 raul kernel: reg:0x06  val:0x001f
Jan 16 21:05:38 raul kernel: reg:0x08  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x0a  val:0x001e
Jan 16 21:05:38 raul kernel: reg:0x0c  val:0x001f
Jan 16 21:05:38 raul kernel: reg:0x0e  val:0x001f
Jan 16 21:05:38 raul kernel: reg:0x10  val:0x0808
Jan 16 21:05:38 raul kernel: reg:0x12  val:0x081f
Jan 16 21:05:38 raul kernel: reg:0x14  val:0x0808
Jan 16 21:05:38 raul kernel: reg:0x16  val:0x0808
Jan 16 21:05:38 raul kernel: reg:0x18  val:0x0808
Jan 16 21:05:38 raul kernel: reg:0x1a  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x1c  val:0x0800
Jan 16 21:05:38 raul kernel: reg:0x1e  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x20  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x22  val:0x000f
Jan 16 21:05:38 raul kernel: reg:0x24  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x26  val:0x000f
Jan 16 21:05:38 raul kernel: reg:0x28  val:0x0005
Jan 16 21:05:38 raul kernel: reg:0x2a  val:0x0401
Jan 16 21:05:38 raul kernel: reg:0x2c  val:0xbb80
Jan 16 21:05:38 raul kernel: reg:0x2e  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x30  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x32  val:0xbb80
Jan 16 21:05:38 raul kernel: reg:0x34  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x36  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x38  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x3a  val:0x2000
Jan 16 21:05:38 raul kernel: reg:0x3c  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x3e  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x40  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x42  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x44  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x46  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x48  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x4a  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x4c  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x4e  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x50  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x52  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x54  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x56  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x58  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x5a  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x5c  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x5e  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x60  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x62  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x64  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x66  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x68  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x6a  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x6c  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x6e  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x70  val:0x0000
Jan 16 21:05:38 raul kernel: reg:0x72  val:0x0002
Jan 16 21:05:38 raul kernel: reg:0x74  val:0x7000
Jan 16 21:05:38 raul kernel: reg:0x76  val:0x0404
Jan 16 21:05:38 raul kernel: reg:0x78  val:0xbb80
Jan 16 21:05:38 raul kernel: reg:0x7a  val:0xbb80
Jan 16 21:05:38 raul kernel: reg:0x7c  val:0x4144
Jan 16 21:05:38 raul kernel: reg:0x7e  val:0x5361
Jan 16 21:05:38 raul kernel: via82cxxx: board #1 at 0x1000, IRQ 5



As you can see, the register are well written in ad1886, so this are my
question, 
---- Does via code inicialization change any value of ad1886?
---- Is possible that ad1886 works fine and the problem were with via
chipset?
----- Any suggestion is welcomed.


Thanks






-- 
-----------------------------------------------
Raul Sanchez Sanchez             raul@dif.um.es
Centro de Calculo               
Facultad de Informatica    Tlf: +34 968 36 4827 
Universidad de Murcia      Fax: +34 968 36 4151
-----------------------------------------------

^ permalink raw reply	[flat|nested] 2+ messages in thread

* Re: Driver via ac97 sound problem (VT82C686) Compaq Presario 700
  2002-01-17  7:48               ` Driver via ac97 sound problem (VT82C686) Compaq Presario 700 Raul Sanchez Sanchez
@ 2002-01-17 21:06                 ` salvador
  0 siblings, 0 replies; 2+ messages in thread
From: salvador @ 2002-01-17 21:06 UTC (permalink / raw)
  To: Raul Sanchez Sanchez
  Cc: Paul Lorenz, Jeremy Lumbroso, ignacio, rubio, Jorge Carminati,
	linux-kernel

Raul Sanchez Sanchez wrote:

>         But my question is, later i set up 1886 chip, does via inicialization
> change my configuration of it?

Try putting some printk in the function that sets the codec registers.

> If i try to print all the register of the
> 1886 in via_card_init_proc it fails :( and i can't be sure that via code
> doesn't change them.

No if the routine to write the registers isn't called *and* the initialization
doesn't reset the codec.
The first can be verified with printks, for the second examine the code. But
via_init_one is the one to check, it calls all the initializations.

> As you can see, the register are well written in ad1886, so this are my
> question,
> ---- Does via code inicialization change any value of ad1886?
> ---- Is possible that ad1886 works fine and the problem were with via
> chipset?

Jeff Garzik should know better ;-)
The only strange thing is the code is for the A version of the chip (desktop?)
and you have the B version (mobile?).
I got the 82C686A data sheet, but not the one for 82C686B.

SET

--
Salvador Eduardo Tropea (SET). (Electronics Engineer)
Visit my home page: http://welcome.to/SetSoft or
http://www.geocities.com/SiliconValley/Vista/6552/
Alternative e-mail: set@computer.org set@ieee.org
Address: Curapaligue 2124, Caseros, 3 de Febrero
Buenos Aires, (1678), ARGENTINA Phone: +(5411) 4759 0013




^ permalink raw reply	[flat|nested] 2+ messages in thread

end of thread, other threads:[~2002-01-17 21:04 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
     [not found] <3C459995.A8EF423A@inti.gov.ar>
     [not found] ` <20020114194209.90225.qmail@web20905.mail.yahoo.com>
     [not found]   ` <3C4342DA.5D19601A@inti.gov.ar>
     [not found]     ` <1011045793.1847.3.camel@raul>
     [not found]       ` <3C441F7E.FD8A345C@inti.gov.ar>
     [not found]         ` <1011100904.535.2.camel@raul>
     [not found]           ` <3C448071.7109C9E5@inti.gov.ar>
     [not found]             ` <1011137857.504.16.camel@raul>
2002-01-17  7:48               ` Driver via ac97 sound problem (VT82C686) Compaq Presario 700 Raul Sanchez Sanchez
2002-01-17 21:06                 ` salvador

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

Powered by JetHome