hdc: lost interrupt

[Derek J Witt <djw@flinthills.com>]

[-- Attachment #1: Type: text/plain, Size: 5261 bytes --]

Good evening, all. I've been trying to get 2.5.x to boot up without
losing IDE interrupts.  I tried disabling multimode in makeconfig but to
no avail.

My IDE controller and chipset are as follows (via dmesg):

ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
    ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA

...

Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
    ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
hda: QUANTUM FIREBALL SE6.4A, ATA DISK drive
hdb: ATAPI CD-ROM DRIVE 40X MAXIMUM, ATAPI CD/DVD-ROM drive
hdc: WDC AC36400L, ATA DISK drive
hdd: CRW6206A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 12594960 sectors (6449 MB) w/80KiB Cache, CHS=784/255/63, UDMA(33)
hdc: 12594960 sectors (6449 MB) w/256KiB Cache, CHS=13328/15/63,
UDMA(33)

And /proc/pci reports my chipset as such: 

  Bus  0, device   0, function  0:
    Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev 196).
      Master Capable.  Latency=8.  
      Prefetchable 32 bit memory at 0xd0000000 [0xd7ffffff].
  Bus  0, device   1, function  0:
    PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (rev 0).
      Master Capable.  No bursts.  Min Gnt=12.
  Bus  0, device   7, function  0:
    ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 64).
  Bus  0, device   7, function  1:
    IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 6).
      Master Capable.  Latency=32.  
      I/O at 0xe000 [0xe00f].

And I have the following IDE kernel setup for 2.5.6-pre1+xfs:

#
# ATA/IDE/MFM/RLL support
#
CONFIG_IDE=y

#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_IDEDISK_STROKE is not set
# CONFIG_BLK_DEV_IDEDISK_VENDOR is not set
# CONFIG_BLK_DEV_IDEDISK_FUJITSU is not set
# CONFIG_BLK_DEV_IDEDISK_IBM is not set
# CONFIG_BLK_DEV_IDEDISK_MAXTOR is not set
# CONFIG_BLK_DEV_IDEDISK_QUANTUM is not set
# CONFIG_BLK_DEV_IDEDISK_SEAGATE is not set
# CONFIG_BLK_DEV_IDEDISK_WD is not set
# CONFIG_BLK_DEV_COMMERIAL is not set
# CONFIG_BLK_DEV_TIVO is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=y
CONFIG_IDE_TASK_IOCTL=y
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
# CONFIG_IDEDMA_PCI_AUTO is not set
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_BLK_DEV_IDEDMA_TIMEOUT is not set
# CONFIG_IDEDMA_NEW_DRIVE_LISTINGS is not set
CONFIG_BLK_DEV_ADMA=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_AEC62XX_TUNING is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_AMD74XX_OVERRIDE is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_HPT34X_AUTODMA is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_PIIX_TUNING is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC_ADMA is not set
# CONFIG_BLK_DEV_PDC202XX is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_PDC202XX_FORCE is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
CONFIG_BLK_DEV_VIA82CXXX=y
# CONFIG_IDE_CHIPSETS is not set
# CONFIG_IDEDMA_AUTO is not set
CONFIG_IDEDMA_IVB=y
# CONFIG_DMA_NONPCI is not set
CONFIG_BLK_DEV_IDE_MODES=y
# CONFIG_BLK_DEV_ATARAID is not set
# CONFIG_BLK_DEV_ATARAID_PDC is not set
# CONFIG_BLK_DEV_ATARAID_HPT is not set

Has anyone else with a Via chipset been able to boot into 2.5.x without having these interrupt problems? Any suggestions will be helpful.

Thanks.
                                   
-- 
**  Derek J Witt                                              **
*   Email: mailto:djw@flinthills.com                           *
*   Home Page: http://www.flinthills.com/~djw/                 *
*** "...and on the eighth day, God met Bill Gates." - Unknown **

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 232 bytes --]