mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
* Re: 2.4.21-pre7 + Intel 82801AA IDE + 80Gb Barracuda do not work well together
  2003-04-16 16:15 2.4.21-pre7 + Intel 82801AA IDE + 80Gb Barracuda do not work well together Pau Aliagas
@ 2003-04-16 15:57 ` Alan Cox
  2003-04-16 17:01   ` Pau Aliagas
  0 siblings, 1 reply; 3+ messages in thread
From: Alan Cox @ 2003-04-16 15:57 UTC (permalink / raw)
  To: Pau Aliagas; +Cc: lkml

On Mer, 2003-04-16 at 17:15, Pau Aliagas wrote:
> I'm having serious trouble dealing with:
> * 80Gb Seagate Barracuda disc (Model Number ST380011A, Firmware Revision 3.04)
> * on an Intel 82801AA IDE controller

Thats a known to work configuration, so that is strange. Is the drive
known good and the driver/controller setup ok in "other OS" if you also
run it ?

> (RH-8.0 updated kernels) unless I boot with ide=nodma.
> With RH kernels it stalls reading the partition table.
> With 2.4.21-pre7 I get and error of the dma.

Same error in both cases, just its recovered properly in the newer code.



^ permalink raw reply	[flat|nested] 3+ messages in thread

* 2.4.21-pre7 + Intel 82801AA IDE + 80Gb Barracuda do not work well together
@ 2003-04-16 16:15 Pau Aliagas
  2003-04-16 15:57 ` Alan Cox
  0 siblings, 1 reply; 3+ messages in thread
From: Pau Aliagas @ 2003-04-16 16:15 UTC (permalink / raw)
  To: lkml


I'm having serious trouble dealing with:
* 80Gb Seagate Barracuda disc (Model Number ST380011A, Firmware Revision 3.04)
* on an Intel 82801AA IDE controller

It does not boot neither with 2.4.21-pre7 nor with any other tested kernel
(RH-8.0 updated kernels) unless I boot with ide=nodma.
With RH kernels it stalls reading the partition table.
With 2.4.21-pre7 I get and error of the dma.

I've tried idebus=66, ide0=ata66 and some tweaks with hdparm to no 
success; each time I enabled dma the system hung.

If someone can enlighten me on how to boot with DMA enabled maybe I'd 
achieve a better performance than this (best result in several tries):
# hdparm -tT /dev/hda
/dev/hda:
 Timing buffer-cache reads:   128 MB in  0.85 seconds =150.66 MB/sec
 Timing buffered disk reads:  64 MB in 11.53 seconds =  5.55 MB/sec

These are the relevant parametres to me.

------------------------------------------------------------
# hdparm -I /dev/hda

/dev/hda:

ATA device, with non-removable media
	Model Number:       ST380011A                               
	Serial Number:      3JV07K8W            
	Firmware Revision:  3.04    
Standards:
	Used: ATA/ATAPI-6 T13 1410D revision 2 
	Supported: 6 5 4 3 
Configuration:
	Logical		max	current
	cylinders	16383	16383
	heads		16	16
	sectors/track	63	63
	--
	CHS current addressable sectors:   16514064
	LBA    user addressable sectors:  156301488
	LBA48  user addressable sectors:  156301488
	device size with M = 1024*1024:       76319 MBytes
	device size with M = 1000*1000:       80026 MBytes (80 GB)
Capabilities:
	LBA, IORDY(can be disabled)
	bytes avail on r/w long: 4	Queue depth: 1
	Standby timer values: spec'd by Standard
	R/W multiple sector transfer: Max = 16	Current = 16
	Recommended acoustic management value: 128, current value: 0
	DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5 
	     Cycle time: min=120ns recommended=120ns
	PIO: pio0 pio1 pio2 pio3 pio4 
	     Cycle time: no flow control=240ns  IORDY flow control=120ns
Commands/features:
	Enabled	Supported:
	   *	READ BUFFER cmd
	   *	WRITE BUFFER cmd
	   *	Host Protected Area feature set
	   *	Look-ahead
	   *	Look-ahead
	   *	Write cache
	   *	Power Management feature set
		Security Mode feature set
	   *	SMART feature set
	   *	FLUSH CACHE EXT command
	   *	Mandatory FLUSH CACHE command 
	   *	Device Configuration Overlay feature set 
	   *	48-bit Address feature set 
		SET MAX security extension
	   *	DOWNLOAD MICROCODE cmd
	   *	SMART self-test 
	   *	SMART error logging 
Security: 
		supported
	not	enabled
	not	locked
	not	frozen
	not	expired: security count
	not	supported: enhanced erase
HW reset results:
	CBLID- above Vih
	Device num = 0 determined by the jumper
Checksum: correct

------------------------------------------------------------

# lspci
00:00.0 Host bridge: Intel Corp. 82820 820 (Camino) Chipset Host Bridge 
(MCH) (rev 04)
00:01.0 PCI bridge: Intel Corp. 82820 820 (Camino) Chipset AGP Bridge (rev 04)
00:1e.0 PCI bridge: Intel Corp. 82801AA PCI Bridge (rev 02)
00:1f.0 ISA bridge: Intel Corp. 82801AA ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corp. 82801AA IDE (rev 02)
00:1f.2 USB Controller: Intel Corp. 82801AA USB (rev 02)
00:1f.3 SMBus: Intel Corp. 82801AA SMBus (rev 02)
00:1f.5 Multimedia audio controller: Intel Corp. 82801AA AC'97 Audio (rev 02)
01:00.0 VGA compatible controller: nVidia Corporation RIVA TNT2 Model 64 (rev 15)
02:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
------------------------------------------------------------

# lsmod
Module                  Size  Used by    Not tainted
nfsd                   79920   8  (autoclean)
lockd                  58064   1  (autoclean) [nfsd]
sunrpc                 79324   1  (autoclean) [nfsd lockd]
autofs                 13348   0  (autoclean) (unused)
3c59x                  30672   1 
iptable_filter          2412   0  (autoclean) (unused)
ip_tables              15224   1  [iptable_filter]
ext3                   70336   1 
jbd                    52212   1  [ext3]
------------------------------------------------------------

# hdparm -i /dev/hda

/dev/hda:

 Model=ST380011A, FwRev=3.04, SerialNo=3JV07K8W
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5 
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:  1 2 3 4 5 6
------------------------------------------------------------

# cat /proc/ide/hda/settings 
name			value		min		max		mode
----			-----		---		---		----
acoustic                0               0               254             rw
address                 1               0               2               rw
address                 1               0               2               rw
bios_cyl                9729            0               65535           rw
bios_head               255             0               255             rw
bios_sect               63              0               63              rw
breada_readahead        8               0               255             rw
bswap                   0               0               1               r
current_speed           0               0               69              rw
failures                0               0               65535           rw
file_readahead          508             0               16384           rw
ide_scsi                0               0               1               rw
init_speed              0               0               69              rw
io_32bit                3               0               3               rw
keepsettings            0               0               1               rw
lun                     0               0               7               rw
max_failures            1               0               65535           rw
max_kb_per_request      128             1               255             rw
multcount               16              0               16              rw
nice1                   1               0               1               rw
nowerr                  0               0               1               rw
number                  0               0               3               rw
pio_mode                write-only      0               255             w
slow                    0               0               1               rw
unmaskirq               1               0               1               rw
using_dma               0               0               1               rw
wcache                  0               0               1               rw
------------------------------------------------------------
And part of the boot mmessages with latest RH-8.0 updated kernel:
# uname -a
Linux fileserver 2.4.18-27.8.0 #1 Fri Mar 14 06:45:49 EST 2003 i686 i686 
i386 GNU/Linux

Booting parametres: ide=nodma idebus=66 ide0=ata66

ide: Assuming 66MHz system bus speed for PIO modes
PIIX4: IDE controller on PCI bus 00 dev f9
PIIX4: chipset revision 2
PIIX4: not 100% native mode: will probe irqs later
PIIX4: ATA-66/100 forced bit set (WARNING)!!
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: ST380011A, ATA DISK drive
hdc: CRD-8482B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c03b26c4, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c03b26c4, I/O limit 4095Mb (mask 0xffffffff)
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63
ide-floppy driver 0.99.newide
Partition check:
 hda: hda1 hda2

Pau


^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: 2.4.21-pre7 + Intel 82801AA IDE + 80Gb Barracuda do not work well together
  2003-04-16 15:57 ` Alan Cox
@ 2003-04-16 17:01   ` Pau Aliagas
  0 siblings, 0 replies; 3+ messages in thread
From: Pau Aliagas @ 2003-04-16 17:01 UTC (permalink / raw)
  To: lkml, Alan Cox

On 16 Apr 2003, Alan Cox wrote:

> On Mer, 2003-04-16 at 17:15, Pau Aliagas wrote:
> > I'm having serious trouble dealing with:
> > * 80Gb Seagate Barracuda disc (Model Number ST380011A, Firmware Revision 3.04)
> > * on an Intel 82801AA IDE controller
> 
> Thats a known to work configuration, so that is strange. Is the drive
> known good and the driver/controller setup ok in "other OS" if you also
> run it ?

I've never tried it with borg OSes, but it used to work flawlessly with a 
40Gb HD. The problem arouse when installing this 80 Gb Barracuda.

> > (RH-8.0 updated kernels) unless I boot with ide=nodma.
> > With RH kernels it stalls reading the partition table.
> > With 2.4.21-pre7 I get and error of the dma.
> 
> Same error in both cases, just its recovered properly in the newer code.

Well, it did not recover as it disabled the hda disc saying something like 
"disc not operative" (take the concept not the words). 

So I rebooted with RH kernel and no dma. And that's what I have now. I'll 
be rebooting now removing all the extra parametres I used (idebus, ide0).

Pau


^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2003-04-16 16:51 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2003-04-16 16:15 2.4.21-pre7 + Intel 82801AA IDE + 80Gb Barracuda do not work well together Pau Aliagas
2003-04-16 15:57 ` Alan Cox
2003-04-16 17:01   ` Pau Aliagas

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®