From: Henry Molina <henrymolina@cmn-consulting.com>
To: "Randy.Dunlap" <rddunlap@osdl.org>
Cc: linux-kernel@vger.kernel.org
Subject: Re: EDD Support
Date: Mon, 09 Aug 2004 12:44:42 -0500 [thread overview]
Message-ID: <1092073482.2907.88.camel@prometeo> (raw)
In-Reply-To: <20040809093545.5a5e1673.rddunlap@osdl.org>
No Randy, no messages, I'm using insmod from BusyBox v1.00-pre10, and
lsmod shows the module ok.
On Mon, 2004-08-09 at 11:35, Randy.Dunlap wrote:
> On Mon, 09 Aug 2004 11:43:31 -0500 Henry Molina wrote:
>
> | Hi everyone,
>
> Hi Henry,
>
> | I'm compiling kernel 2.6.7 with CONFIG_EDD fine, then I proceed to
> | install the module but I can't get the /proc/sys/firmware/edd entry.
> |
> | Any Suggestion?.
>
> Any kernel log messages when you load the module?
> Hint: there should be.
>
> | Many Thanks,
> |
> | Henry Molina
> |
> | PD: I attach the dmidecode output
> |
> | # dmidecode 2.2
> | SMBIOS 2.3 present.
> | 31 structures occupying 1017 bytes.
> | Table at 0x000F0630.
> | Handle 0x0000
> | DMI type 0, 20 bytes.
> | BIOS Information
> | Vendor: American Megatrends Inc.
> | Version: 1.02
> | Release Date: 05/09/2003
> | Address: 0xF0000
> | Runtime Size: 64 kB
> | ROM Size: 512 kB
> | Characteristics:
> | ISA is supported
> | PCI is supported
> | PNP is supported
> | APM is supported
> | BIOS is upgradeable
> | BIOS shadowing is allowed
> | ESCD support is available
> | Boot from CD is supported
> | Selectable boot is supported
> | BIOS ROM is socketed
> | EDD is supported
> | 5.25"/360 KB floppy services are supported (int 13h)
> | 5.25"/1.2 MB floppy services are supported (int 13h)
> | 3.5"/720 KB floppy services are supported (int 13h)
> | 3.5"/2.88 MB floppy services are supported (int 13h)
> | Print screen service is supported (int 5h)
> | 8042 keyboard services are supported (int 9h)
> | Printer services are supported (int 17h)
> | CGA/mono video services are supported (int 10h)
> | ACPI is supported
> | USB legacy is supported
> | AGP is supported
> | LS-120 boot is supported
> | ATAPI Zip drive boot is supported
> | BIOS boot specification is supported
> | Handle 0x0001
> | DMI type 1, 25 bytes.
> | System Information
> | Manufacturer: Hewlett-Packard
> | Product Name: HP d220 MT (DC526A)
> | Version:
> | Serial Number: MXD33701GQ
> | UUID: 15F4C490-59EA-D711-851C-517B4801761B
> | Wake-up Type: Power Switch
> | Handle 0x0002
> | DMI type 2, 8 bytes.
> | Base Board Information
> | Manufacturer: Lite-On Tech.
> | Product Name: 0888h
> | Version:
> | Serial Number: 01234567
> | Handle 0x0003
> | DMI type 3, 17 bytes.
> | Chassis Information
> | Manufacturer: Hewlett-Packard
> | Type: Desktop
> | Lock: Not Present
> | Version:
> | Serial Number:
> | Asset Tag:
> | Boot-up State: Safe
> | Power Supply State: Safe
> | Thermal State: Safe
> | Security Status: None
> | OEM Information: 0x00000000
> | Handle 0x0004
> | DMI type 4, 32 bytes.
> | Processor Information
> | Socket Designation: mPGA-478
> | Type: Central Processor
> | Family: Pentium 4
> | Manufacturer: Intel
> | ID: 29 0F 41 33 FF FB EB BF
> | Signature: Type 0, Family 34F, Model 12, Stepping 9
> | Flags:
> | FPU (Floating-point unit on-chip)
> | VME (Virtual mode extension)
> | DE (Debugging extension)
> | PSE (Page size extension)
> | TSC (Time stamp counter)
> | MSR (Model specific registers)
> | PAE (Physical address extension)
> | MCE (Machine check exception)
> | CX8 (CMPXCHG8 instruction supported)
> | APIC (On-chip APIC hardware supported)
> | SEP (Fast system call)
> | MTRR (Memory type range registers)
> | PGE (Page global enable)
> | MCA (Machine check architecture)
> | CMOV (Conditional move instruction supported)
> | PAT (Page attribute table)
> | PSE-36 (36-bit page size extension)
> | CLFSH (CLFLUSH instruction supported)
> | DS (Debug store)
> | ACPI (ACPI supported)
> | MMX (MMX technology supported)
> | FXSR (Fast floating-point save and restore)
> | SSE (Streaming SIMD extensions)
> | SSE2 (Streaming SIMD extensions 2)
> | SS (Self-snoop)
> | HTT (Hyper-threading technology)
> | TM (Thermal monitor supported)
> | SBF (Signal break on FERR)
> | Version: PENTIUM 4
> | Voltage: 2.9 V
> | External Clock: 133 MHz
> | Max Speed: 4000 MHz
> | Current Speed: 2400 MHz
> | Status: Populated, Enabled
> | Upgrade: ZIF Socket
> | L1 Cache Handle: 0x0005
> | L2 Cache Handle: 0x0006
> | L3 Cache Handle: Not Provided
> | Handle 0x0005
> | DMI type 7, 19 bytes.
> | Cache Information
> | Socket Designation: Internal Cache
> | Configuration: Enabled, Not Socketed, Level 1
> | Operational Mode: Write Back
> | Location: Internal
> | Installed Size: 8 KB
> | Maximum Size: 1024 KB
> | Supported SRAM Types:
> | Synchronous
> | Installed SRAM Type: Pipeline Burst Synchronous
> | Speed: 40 ns
> | Error Correction Type: Single-bit ECC
> | System Type: Data
> | Associativity: 4-way Set-associative
> | Handle 0x0006
> | DMI type 7, 19 bytes.
> | Cache Information
> | Socket Designation: Internal Cache
> | Configuration: Enabled, Not Socketed, Level 2
> | Operational Mode: Write Back
> | Location: Internal
> | Installed Size: 512 KB
> | Maximum Size: 1024 KB
> | Supported SRAM Types:
> | Synchronous
> | Installed SRAM Type: Synchronous
> | Speed: 40 ns
> | Error Correction Type: Parity
> | System Type: Unified
> | Associativity: 8-way Set-associative
> | Handle 0x0007
> | DMI type 5, 20 bytes.
> | Memory Controller Information
> | Error Detecting Method: None
> | Error Correcting Capabilities: None
> | Supported Interleave: One-way Interleave
> | Current Interleave: One-way Interleave
> | Maximum Memory Module Size: 1024 MB
> | Maximum Total Memory Size: 2048 MB
> | Supported Speeds:
> | Other
> | Supported Memory Types:
> | DIMM
> | SDRAM
> | Memory Module Voltage: 3.3 V
> | Associated Memory Slots: 2
> | 0x0008
> | 0x0009
> | Enabled Error Correcting Capabilities: None
> | Handle 0x0008
> | DMI type 6, 12 bytes.
> | Memory Module Information
> | Socket Designation: DIMM1
> | Bank Connections: 1 0
> | Current Speed: Unknown
> | Type: DIMM SDRAM
> | Installed Size: 128 MB (Single-bank Connection)
> | Enabled Size: 128 MB (Single-bank Connection)
> | Error Status: OK
> | Handle 0x0009
> | DMI type 6, 12 bytes.
> | Memory Module Information
> | Socket Designation: DIMM2
> | Bank Connections: 3 2
> | Current Speed: Unknown
> | Type: Unknown
> | Installed Size: Not Installed (Single-bank Connection)
> | Enabled Size: Not Installed (Single-bank Connection)
> | Error Status: OK
> | Handle 0x000A
> | DMI type 9, 13 bytes.
> | System Slot Information
> | Designation: PCI1
> | Type: 32-bit PCI
> | Current Usage: Available
> | Length: Long
> | ID: 1
> | Characteristics:
> | 3.3 V is provided
> | Opening is shared
> | PME signal is supported
> | Handle 0x000B
> | DMI type 9, 13 bytes.
> | System Slot Information
> | Designation: PCI2
> | Type: 32-bit PCI
> | Current Usage: Available
> | Length: Long
> | ID: 2
> | Characteristics:
> | 3.3 V is provided
> | Opening is shared
> | PME signal is supported
> | Handle 0x000C
> | DMI type 9, 13 bytes.
> | System Slot Information
> | Designation: PCI3
> | Type: 32-bit PCI
> | Current Usage: Available
> | Length: Long
> | ID: 3
> | Characteristics:
> | 3.3 V is provided
> | Opening is shared
> | PME signal is supported
> | Handle 0x000D
> | DMI type 9, 13 bytes.
> | System Slot Information
> | Designation: AGP
> | Type: 32-bit PCI
> | Current Usage: Available
> | Length: Long
> | ID: 1
> | Characteristics:
> | 3.3 V is provided
> | Opening is shared
> | PME signal is supported
> | Handle 0x000E
> | DMI type 11, 5 bytes.
> | OEM Strings
> | String 1: SMBIOS Support from AMI
> | Handle 0x000F
> | DMI type 8, 9 bytes.
> | Port Connector Information
> | Internal Reference Designator: USB0
> | Internal Connector Type: None
> | External Reference Designator: USB1
> | External Connector Type: Access Bus (USB)
> | Port Type: USB
> | Handle 0x0010
> | DMI type 8, 9 bytes.
> | Port Connector Information
> | Internal Reference Designator: USB1
> | Internal Connector Type: None
> | External Reference Designator: USB2
> | External Connector Type: Access Bus (USB)
> | Port Type: USB
> | Handle 0x0011
> | DMI type 8, 9 bytes.
> | Port Connector Information
> | Internal Reference Designator: USB2
> | Internal Connector Type: None
> | External Reference Designator: USB3
> | External Connector Type: Access Bus (USB)
> | Port Type: USB
> | Handle 0x0012
> | DMI type 8, 9 bytes.
> | Port Connector Information
> | Internal Reference Designator: USB3
> | Internal Connector Type: None
> | External Reference Designator: USB4
> | External Connector Type: Access Bus (USB)
> | Port Type: USB
> | Handle 0x0013
> | DMI type 8, 9 bytes.
> | Port Connector Information
> | Internal Reference Designator: USB4
> | Internal Connector Type: None
> | External Reference Designator: USB5
> | External Connector Type: Access Bus (USB)
> | Port Type: USB
> | Handle 0x0014
> | DMI type 8, 9 bytes.
> | Port Connector Information
> | Internal Reference Designator: USB5
> | Internal Connector Type: None
> | External Reference Designator: USB6
> | External Connector Type: Access Bus (USB)
> | Port Type: USB
> | Handle 0x0015
> | DMI type 8, 9 bytes.
> | Port Connector Information
> | Internal Reference Designator: COM1
> | Internal Connector Type: 9 Pin Dual Inline (pin 10 cut)
> | External Reference Designator: COM1
> | External Connector Type: DB-9 male
> | Port Type: Serial Port 16550A Compatible
> | Handle 0x0016
> | DMI type 8, 9 bytes.
> | Port Connector Information
> | Internal Reference Designator: LPT
> | Internal Connector Type: 25 Pin Dual Inline (pin 26 cut)
> | External Reference Designator: LPT
> | External Connector Type: DB-25 male
> | Port Type: Parallel Port ECP/EPP
> | Handle 0x0017
> | DMI type 8, 9 bytes.
> | Port Connector Information
> | Internal Reference Designator: KEYBOARD
> | Internal Connector Type: None
> | External Reference Designator: KEYBOARD
> | External Connector Type: PS/2
> | Port Type: Keyboard Port
> | Handle 0x0018
> | DMI type 8, 9 bytes.
> | Port Connector Information
> | Internal Reference Designator: MOUSE
> | Internal Connector Type: None
> | External Reference Designator: MOUSE
> | External Connector Type: PS/2
> | Port Type: Mouse Port
> | Handle 0x0019
> | DMI type 8, 9 bytes.
> | Port Connector Information
> | Internal Reference Designator: Floppy
> | Internal Connector Type: On Board Floppy
> | External Reference Designator: Floppy
> | External Connector Type: None
> | Port Type: None
> | Handle 0x001A
> | DMI type 8, 9 bytes.
> | Port Connector Information
> | Internal Reference Designator: Primary IDE
> | Internal Connector Type: On Board IDE
> | External Reference Designator: IDE-1
> | External Connector Type: None
> | Port Type: None
> | Handle 0x001B
> | DMI type 8, 9 bytes.
> | Port Connector Information
> | Internal Reference Designator: Secondary IDE
> | Internal Connector Type: On Board IDE
> | External Reference Designator: IDE-2
> | External Connector Type: None
> | Port Type: None
> | Handle 0x001C
> | DMI type 12, 5 bytes.
> | System Configuration Options
> | Option 1: System Management BIOS from Atlanta
> | Handle 0x001D
> | DMI type 13, 22 bytes.
> | BIOS Language Information
> | Installable Languages: 4
> | English
> | Traditional Chinese
> | Simplified Chinese
> | Japanese
> | Currently Installed Language: English
> | Handle 0x001E
> | DMI type 127, 4 bytes.
> | End Of Table
>
>
> --
> ~Randy
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
--
Henry Molina
R&D
CMN Consulting
next prev parent reply other threads:[~2004-08-09 17:46 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-08-09 16:43 Henry Molina
2004-08-09 16:35 ` Randy.Dunlap
2004-08-09 17:44 ` Henry Molina [this message]
2004-08-09 20:10 ` Henry Molina
2004-08-09 20:14 ` Randy.Dunlap
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1092073482.2907.88.camel@prometeo \
--to=henrymolina@cmn-consulting.com \
--cc=linux-kernel@vger.kernel.org \
--cc=rddunlap@osdl.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®