* Re: 2.6.16-rc1
[not found] ` <20060123225956.GD4307@rene-engelhard.de>
@ 2006-02-11 13:41 ` Roger Leigh
2006-02-12 5:45 ` 2.6.16-rc1 Benjamin Herrenschmidt
0 siblings, 1 reply; 3+ messages in thread
From: Roger Leigh @ 2006-02-11 13:41 UTC (permalink / raw)
To: Rene Engelhard; +Cc: Linux Kernel ML, benh, debian-powerpc
[-- Attachment #1.1: Type: text/plain, Size: 2625 bytes --]
Rene Engelhard <rene@debian.org> writes:
> Emmanuel Galatoulas wrote:
>> >
>> >Has anyone managed to get linux-2.6.16-rc1 to boot successfully on a
>> >powermac? It appears to detect the IDE controller and HDD on my mac
>> >mini, but then fails to mount the root fs. (It's hard to double check
>> >this because the USB keyboard isn't initialised by the failure, so I
>> >can't scroll back to check.)
>
> Yep. same here. iBook G4.
Further investigation (using netconsole) shows the breakage (in
2.6.16-rc1 and -rc2) is due to discovering an additional IDE
controller (KeyLargo) before the normal (UniNorth) controller:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
+ide0: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24
PCI: Enabling device 0002:20:0d.0 (0000 -> 0002)
-ide0: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39
-hda: TOSHIBA MK8025GAS, ATA DISK drive
-hdb: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive
-hda: Enabling Ultra DMA 5
-hdb: Enabling Ultra DMA 2
-ide0 at 0xe1022000-0xe1022007,0xe1022160 on irq 39
-ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24
-hda: max request size: 1024KiB
-hda: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100)
-hda: cache flushes supported
- hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7
-hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
+ide1: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39
+hdc: TOSHIBA MK8025GAS, ATA DISK drive
+hdd: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive
+hdc: Enabling Ultra DMA 5
+hdd: Enabling Ultra DMA 2
+ide1 at 0xe102a000-0xe102a007,0xe102a160 on irq 39
+hdc: max request size: 512KiB
+hdc: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100)
+hdc: cache flushes supported
+ hdc: [mac] hdc1 hdc2 hdc3 hdc4 hdc5 hdc6 hdc7
+hdd: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
As a result, the IDE device names are changed and the boot fails. If
the controllers were discovered in the reverse order, it wouldn't
break existing installations.
In both these cases the systems are G4-based PowerMacs (Mac Mini and
iBook). In the case of the Mini, I'm not even certain it's physically
possible to use this additional controller, given how closed the
system is.
Regards,
Roger
--
Roger Leigh
Printing on GNU/Linux? http://gutenprint.sourceforge.net/
Debian GNU/Linux http://www.debian.org/
GPG Public Key: 0x25BFB848. Please sign and encrypt your mail.
[-- Attachment #1.2: 2.6.15.1 boot --]
[-- Type: text/plain, Size: 14456 bytes --]
$ netcat -u -l -p 4444
Total memory = 512MB; using 1024kB for hash table (at c0400000)
Linux version 2.6.15.1 (rleigh@hardknott) (gcc version 4.0.3 20060115 (prerelease) (Debian 4.0.2-7)) #22 Wed Feb 8 20:44:14 GMT 2006
Found UniNorth memory controller & host bridge, revision: 210
Mapped at 0xfddf4000
Found a Intrepid mac-io controller, rev: 0, mapped at 0xfdd74000
Processor NAP mode on idle enabled.
PowerMac motherboard: Mac mini
Enabling clock spreading on Intrepid ASIC
Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0
Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0
Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0
via-pmu: Server Mode is disabled
PMU driver 2 initialized for Core99, firmware: 55
nvram: Checking bank 0...
nvram: gen0=470, gen1=469
nvram: Active bank is: 0
nvram: OF partition at 0x410
nvram: XP partition at 0x1020
nvram: NR partition at 0x1120
Built 1 zonelists
Kernel command line: root=/dev/hda3 ro video=radeonfb:1680x1050-32@60 netconsole=@1/,4444@10.0.0.12/
netconsole: local port 6665
netconsole: local IP 1.0.0.0
netconsole: interface eth0
netconsole: remote port 4444
netconsole: remote IP 10.0.0.12
netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
PowerMac using OpenPIC irq controller at 0x80040000
OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc523000
OpenPIC timer frequency is 4.166666 MHz
PID hash table entries: 4096 (order: 12, 65536 bytes)
GMT Delta read from XPRAM: 0 minutes, DST: off
time_init: decrementer frequency = 41.620997 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 514048k available (2696k kernel code, 1044k data, 164k init, 0k highmem)
AGP special page: 0xdffff000
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
device-tree: property "l2-cache" name conflicts with node in /cpus/PowerPC,G4@0
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 0 of device 0001:10:18.0
PCI: Cannot allocate resource region 0 of device 0001:10:19.0
Apple USB OHCI 0001:10:18.0 disabled by firmware
Apple USB OHCI 0001:10:19.0 disabled by firmware
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Thermal assist unit not available
audit: initializing netlink socket (disabled)
audit(1139431511.116:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
PCI: Enabling device 0000:00:10.0 (0006 -> 0007)
radeonfb: Retreived PLL infos from Open Firmware
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=190.00 Mhz, System=250.00 MHz
radeonfb: PLL min 12000 max 35000
radeonfb: Monitor 1 type DFP found
radeonfb: EDID probed
radeonfb: Monitor 2 type DFP found
radeonfb: EDID probed
Console: switching to colour frame buffer device 210x65
radeonfb (0000:00:10.0): ATI Radeon Yb
Generic RTC Driver v1.07
Macintosh non-volatile memory driver v1.1
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected Apple UniNorth 2 chipset
agpgart: configuring for size idx: 4
agpgart: AGP aperture is 16M @ 0x0
[drm] Initialized drm 1.0.0 20040925
[drm] Initialized radeon 1.19.0 20050911 on minor 0:
sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:11:24:75:6d:56
eth0: Found BCM5221 PHY
netconsole: device eth0 not up yet, forcing it
eth0: Link is up at 100 Mbps, full-duplex.
eth0: Pause is disabled
netconsole: network logging started
MacIO PCI driver attached to Intrepid chipset
input: Macintosh mouse button emulation as /class/input/input0
apm_emu: APM Emulation 0.5 initialized.
adb: starting probe task...
adb: finished probe task...
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PCI: Enabling device 0002:20:0d.0 (0000 -> 0002)
ide0: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39
hda: TOSHIBA MK8025GAS, ATA DISK drive
hdb: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive
hda: Enabling Ultra DMA 5
hdb: Enabling Ultra DMA 2
ide0 at 0xe1022000-0xe1022007,0xe1022160 on irq 39
ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24
hda: max request size: 1024KiB
hda: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7
hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
usbmon: debugfs is not available
PCI: Enabling device 0001:10:1b.2 (0004 -> 0006)
ehci_hcd 0001:10:1b.2: EHCI Host Controller
ehci_hcd 0001:10:1b.2: new USB bus registered, assigned bus number 1
ehci_hcd 0001:10:1b.2: irq 63, io mem 0x80080000
ehci_hcd 0001:10:1b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.15.1 ehci_hcd
usb usb1: SerialNumber: 0001:10:1b.2
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
Apple USB OHCI 0001:10:18.0 disabled by firmware
Apple USB OHCI 0001:10:19.0 disabled by firmware
PCI: Enabling device 0001:10:1a.0 (0000 -> 0002)
ohci_hcd 0001:10:1a.0: OHCI Host Controller
ohci_hcd 0001:10:1a.0: new USB bus registered, assigned bus number 2
ohci_hcd 0001:10:1a.0: irq 29, io mem 0x80083000
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.15.1 ohci_hcd
usb usb2: SerialNumber: 0001:10:1a.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Enabling device 0001:10:1b.0 (0000 -> 0002)
ohci_hcd 0001:10:1b.0: OHCI Host Controller
ohci_hcd 0001:10:1b.0: new USB bus registered, assigned bus number 3
ohci_hcd 0001:10:1b.0: irq 63, io mem 0x80082000
usb 1-2: new high speed USB device using ehci_hcd and address 3
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.15.1 ohci_hcd
usb usb3: SerialNumber: 0001:10:1b.0
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 3 ports detected
PCI: Enabling device 0001:10:1b.1 (0000 -> 0002)
ohci_hcd 0001:10:1b.1: OHCI Host Controller
ohci_hcd 0001:10:1b.1: new USB bus registered, assigned bus number 4
ohci_hcd 0001:10:1b.1: irq 63, io mem 0x80081000
usb usb4: Product: OHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.15.1 ohci_hcd
usb usb4: SerialNumber: 0001:10:1b.1
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v2.3
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb 3-1: new full speed USB device using ohci_hcd and address 2
usb 3-1: Product: Hub in Apple Extended USB Keyboard
usb 3-1: Manufacturer: Mitsumi Electric
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 3 ports detected
usbcore: registered new driver hiddev
usb 1-2.2: new low speed USB device using ehci_hcd and address 4
usb 1-2.2: Product: Microsoft 3-Button Mouse with IntelliEye(TM)
usb 1-2.2: Manufacturer: Microsoft
usb 1-2.3: new low speed USB device using ehci_hcd and address 5
usb 1-2.3: Product: Apple Cinema Display
input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input1
input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0001:10:1b.2-2.2
hiddev0: USB HID v1.11 Device [Apple Cinema Display] on usb-0001:10:1b.2-2.3
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits
Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
dmasound_pmac: couldn't find a Codec we can handle
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 164k init
usb 3-1.1: new full speed USB device using ohci_hcd and address 3
usb 3-1.1: Product: USB DRIVE
usb 3-1.1: Manufacturer: KINGSTON
usb 3-1.1: SerialNumber: 1120046114165
scsi0 : SCSI emulation for USB Mass Storage devices
usb 3-1.3: new full speed USB device using ohci_hcd and address 4
usb 3-1.3: Product: Apple Extended USB Keyboard
usb 3-1.3: Manufacturer: Mitsumi Electric
input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input2
input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3
input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input3
input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3
ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
PCI: Enabling device 0002:20:0e.0 (0000 -> 0002)
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[2048]
Vendor: KINGSTON Model: USB DRIVE Rev: 1.12
Type: Direct-Access ANSI SCSI revision: 01 CCS
SCSI device sda: 251904 512-byte hdwr sectors (129 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
hda: Enabling Ultra DMA 5
SCSI device sda: 251904 512-byte hdwr sectors (129 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
sda:<7>usb-storage: queuecommand called
sda1 sda2
sd 0:0:0:0: Attached scsi removable disk sda
eth1394: $Rev: 1312 $ Ben Collins <bcollins@debian.org>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
hda: Enabling Ultra DMA 5
EXT3 FS on hda3, internal journal
sbp2: $Rev: 1306 $ Ben Collins <bcollins@debian.org>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
input: PowerMac Beep as /class/input/input4
device-mapper: snapshot is marked invalid
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on dm-6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
HFS+-fs: write access to a jounaled filesystem is not supported, use the force option at your own risk, mounting read-only.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-14, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2097144k swap on /dev/mapper/hda_vg-swap0. Priority:2 extents:1 across:2097144k
Adding 2097144k swap on /dev/mapper/hda_vg-swap1. Priority:1 extents:1 across:2097144k
Adding 2097144k swap on /dev/mapper/hda_vg-swap2. Priority:3 extents:1 across:2097144k
NET: Registered protocol family 17
sixxs: Disabled Privacy Extensions
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
NFSD: starting 90-second grace period
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 1x mode
[drm] Loading R200 Microcode
usb 3-1: USB disconnect, address 2
usb 3-1.1: USB disconnect, address 3
usb 3-1.3: USB disconnect, address 4
usb 3-1: new full speed USB device using ohci_hcd and address 5
usb 3-1: Product: Hub in Apple Extended USB Keyboard
usb 3-1: Manufacturer: Mitsumi Electric
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 3 ports detected
usb 3-1.1: new full speed USB device using ohci_hcd and address 6
usb 3-1.1: Product: USB DRIVE
usb 3-1.1: Manufacturer: KINGSTON
usb 3-1.1: SerialNumber: 1120046114165
scsi1 : SCSI emulation for USB Mass Storage devices
usb 3-1.3: new full speed USB device using ohci_hcd and address 7
usb 3-1.3: Product: Apple Extended USB Keyboard
usb 3-1.3: Manufacturer: Mitsumi Electric
input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input5
input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3
input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input6
input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3
usbcore: registered new driver ub
Vendor: KINGSTON Model: USB DRIVE Rev: 1.12
Type: Direct-Access ANSI SCSI revision: 01 CCS
SCSI device sda: 251904 512-byte hdwr sectors (129 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
SCSI device sda: 251904 512-byte hdwr sectors (129 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
sda:<7>usb-storage: queuecommand called
sda1 sda2
sd 1:0:0:0: Attached scsi removable disk sda
[-- Attachment #1.3: 2.6.16-rc2 boot --]
[-- Type: text/plain, Size: 12926 bytes --]
$ netcat -u -l -p 4444
Total memory = 512MB; using 1024kB for hash table (at cff00000)
Linux version 2.6.16-rc2 (rleigh@hardknott) (gcc version 4.0.3 20060115 (prerelease) (Debian 4.0.2-7)) #4 Wed Feb 8 18:56:44 GMT 2006
Found UniNorth memory controller & host bridge @ 0xf8000000 revision: 0xd2
Mapped at 0xfdfc0000
Found a Intrepid mac-io controller, rev: 0, mapped at 0xfdf40000
Processor NAP mode on idle enabled.
PowerMac motherboard: Mac mini
Using native/NAP idle loop
Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0
Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0
Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0
via-pmu: Server Mode is disabled
PMU driver v2 initialized for Core99, firmware: 55
nvram: Checking bank 0...
nvram: gen0=470, gen1=469
nvram: Active bank is: 0
nvram: OF partition at 0x410
nvram: XP partition at 0x1020
nvram: NR partition at 0x1120
Top of RAM: 0x20000000, Total RAM: 0x20000000
Memory hole size: 0MB
Built 1 zonelists
Kernel command line: root=/dev/hda3 ro video=radeonfb:1680x1050-32@60 netconsole=@1/,4444@10.0.0.12/
netconsole: local port 6665
netconsole: local IP 1.0.0.0
netconsole: interface eth0
netconsole: remote port 4444
netconsole: remote IP 10.0.0.12
netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs
mpic: ISU size: 64, shift: 6, mask: 3f
mpic: Initializing for 64 sources
PID hash table entries: 4096 (order: 12, 65536 bytes)
GMT Delta read from XPRAM: 0 minutes, DST: off
time_init: decrementer frequency = 41.620997 MHz
time_init: processor frequency = 1416.666661 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 514048k/524288k available (2996k kernel code, 9744k reserved, 308k data, 190k bss, 148k init)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
device-tree: property "l2-cache" name conflicts with node in /cpus/PowerPC,G4@0
NET: Registered protocol family 16
KeyWest i2c @0xf8001003 irq 42 /uni-n@f8000000/i2c@f8001000
channel 0 bus <multibus>
channel 1 bus <multibus>
KeyWest i2c @0x80018000 irq 26 /pci@f2000000/mac-io@17/i2c@18000
channel 0 bus <multibus>
PMU i2c /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c
channel 1 bus <multibus>
channel 2 bus <multibus>
pmf: registering driver for node /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c/temp-monitor@190
pmf: no functions, disposing..
Installing base platform functions...
Installing MMIO functions for macio /pci@f2000000/mac-io@17
pmf: registering driver for node /pci@f2000000/mac-io@17
pmf: Adding functions for platform-do-wor-enable
pmf: idx 1: flags=08000000, phandle=ff97f4d0 16 bytes remaining, parsing...
pmf: Added 1 functions
pmf: Adding functions for platform-do-wor-disable
pmf: idx 1: flags=08000000, phandle=ff97f4d0 16 bytes remaining, parsing...
pmf: Added 1 functions
Installing GPIO functions for macio /pci@f2000000/mac-io@17
pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/modem-reset@1d
pmf: Adding functions for platform-do-modem-reset
pmf: idx 1: flags=08000000, phandle=ff975e48 12 bytes remaining, parsing...
pmf: Added 1 functions
pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/modem-power@1c
pmf: Adding functions for platform-do-modem-power
pmf: idx 1: flags=08000000, phandle=ff975e48 40 bytes remaining, parsing...
pmf: Added 1 functions
pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/extint-gpio1@9
pmf: no functions, disposing..
pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/programmer-switch@11
pmf: no functions, disposing..
pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/gpio5@6f
pmf: no functions, disposing..
pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/gpio6@70
pmf: no functions, disposing..
pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/extint-gpio15@67
pmf: no functions, disposing..
Calling initial GPIO functions for macio /pci@f2000000/mac-io@17
Installing functions for UniN /uni-n@f8000000
pmf: registering driver for node /uni-n@f8000000
pmf: no functions, disposing..
Installing functions for UniN clock /uni-n@f8000000/hw-clock
pmf: registering driver for node /uni-n@f8000000/hw-clock
pmf: Adding functions for platform-do-clockspreading
pmf: idx 1: flags=20000000, phandle=00000000 56 bytes remaining, parsing...
pmf: idx 2: flags=10000000, phandle=00000000 16 bytes remaining, parsing...
pmf: Added 2 functions
All base functions installed
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 0 of device 0001:10:18.0
PCI: Cannot allocate resource region 0 of device 0001:10:19.0
Apple USB OHCI 0001:10:18.0 disabled by firmware
Apple USB OHCI 0001:10:19.0 disabled by firmware
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Thermal assist unit not available
audit: initializing netlink socket (disabled)
audit(1139426338.104:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Enabling device 0000:00:10.0 (0006 -> 0007)
radeonfb: Retrieved PLL infos from Open Firmware
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=190.00 Mhz, System=250.00 MHz
radeonfb: PLL min 12000 max 35000
radeonfb: Monitor 1 type DFP found
radeonfb: EDID probed
radeonfb: Monitor 2 type DFP found
radeonfb: EDID probed
Console: switching to colour frame buffer device 210x65
radeonfb (0000:00:10.0): ATI Radeon Yb
Generic RTC Driver v1.07
Macintosh non-volatile memory driver v1.1
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected Apple UniNorth 2 chipset
agpgart: configuring for size idx: 4
agpgart: AGP aperture is 16M @ 0x0
[drm] Initialized drm 1.0.1 20051102
[drm] Initialized radeon 1.21.0 20051229 on minor 0
sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:11:24:75:6d:56
eth0: Found BCM5221 PHY
netconsole: device eth0 not up yet, forcing it
eth0: Link is up at 100 Mbps, full-duplex.
eth0: Pause is disabled
netconsole: network logging started
MacIO PCI driver attached to Intrepid chipset
adb: starting probe task...
adb: finished probe task...
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24
PCI: Enabling device 0002:20:0d.0 (0000 -> 0002)
ide1: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39
hdc: TOSHIBA MK8025GAS, ATA DISK drive
hdd: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive
hdc: Enabling Ultra DMA 5
hdd: Enabling Ultra DMA 2
ide1 at 0xe102a000-0xe102a007,0xe102a160 on irq 39
hdc: max request size: 512KiB
hdc: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100)
hdc: cache flushes supported
hdc: [mac] hdc1 hdc2 hdc3 hdc4 hdc5 hdc6 hdc7
hdd: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
usbmon: debugfs is not available
PCI: Enabling device 0001:10:1b.2 (0004 -> 0006)
ehci_hcd 0001:10:1b.2: EHCI Host Controller
ehci_hcd 0001:10:1b.2: new USB bus registered, assigned bus number 1
ehci_hcd 0001:10:1b.2: irq 63, io mem 0x80080000
ehci_hcd 0001:10:1b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.16-rc2 ehci_hcd
usb usb1: SerialNumber: 0001:10:1b.2
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
Apple USB OHCI 0001:10:18.0 disabled by firmware
Apple USB OHCI 0001:10:19.0 disabled by firmware
PCI: Enabling device 0001:10:1a.0 (0000 -> 0002)
ohci_hcd 0001:10:1a.0: OHCI Host Controller
ohci_hcd 0001:10:1a.0: new USB bus registered, assigned bus number 2
ohci_hcd 0001:10:1a.0: irq 29, io mem 0x80083000
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.16-rc2 ohci_hcd
usb usb2: SerialNumber: 0001:10:1a.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Enabling device 0001:10:1b.0 (0000 -> 0002)
ohci_hcd 0001:10:1b.0: OHCI Host Controller
ohci_hcd 0001:10:1b.0: new USB bus registered, assigned bus number 3
ohci_hcd 0001:10:1b.0: irq 63, io mem 0x80082000
usb 1-2: new high speed USB device using ehci_hcd and address 3
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.16-rc2 ohci_hcd
usb usb3: SerialNumber: 0001:10:1b.0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 3 ports detected
PCI: Enabling device 0001:10:1b.1 (0000 -> 0002)
ohci_hcd 0001:10:1b.1: OHCI Host Controller
ohci_hcd 0001:10:1b.1: new USB bus registered, assigned bus number 4
ohci_hcd 0001:10:1b.1: irq 63, io mem 0x80081000
usb usb4: Product: OHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.16-rc2 ohci_hcd
usb usb4: SerialNumber: 0001:10:1b.1
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v2.3
Initializing USB Mass Storage driver...
usb 3-1: new full speed USB device using ohci_hcd and address 2
usb 3-1: Product: Hub in Apple Extended USB Keyboard
usb 3-1: Manufacturer: Mitsumi Electric
usb 3-1: configuration #1 chosen from 1 choice
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 3 ports detected
usb 1-2.2: new low speed USB device using ehci_hcd and address 4
usb 1-2.2: Product: Microsoft 3-Button Mouse with IntelliEye(TM)
usb 1-2.2: Manufacturer: Microsoft
usb 1-2.2: configuration #1 chosen from 1 choice
usb 1-2.3: new low speed USB device using ehci_hcd and address 5
usb 1-2.3: Product: Apple Cinema Display
usb 1-2.3: configuration #1 chosen from 1 choice
usb 3-1.1: new full speed USB device using ohci_hcd and address 3
usb 3-1.1: Product: USB DRIVE
usb 3-1.1: Manufacturer: KINGSTON
usb 3-1.1: SerialNumber: 1120046114165
usb 3-1.1: configuration #1 chosen from 1 choice
usb 3-1.3: new full speed USB device using ohci_hcd and address 4
usb 3-1.3: Product: Apple Extended USB Keyboard
usb 3-1.3: Manufacturer: Mitsumi Electric
usb 3-1.3: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input0
input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0001:10:1b.2-2.2
hiddev0: USB HID v1.11 Device [Apple Cinema Display] on usb-0001:10:1b.2-2.3
input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input1
input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3
input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input2
input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
PowerMac i2c bus pmu 2 registered
PowerMac i2c bus pmu 1 registered
PowerMac i2c bus mac-io 0 registered
PowerMac i2c bus uni-n 1 registered
PowerMac i2c bus uni-n 0 registered
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
VFS: Cannot open root device "hda3" or unknown-block(0,0)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
<0>Rebooting in 180 seconds..<7>eth0: no IPv6 routers present
[-- Attachment #1.4: Diff of the bootlogs --]
[-- Type: text/plain, Size: 20197 bytes --]
--- bootlog-2.6.15-ppc 2006-02-11 13:24:36.000000000 +0000
+++ bootlog-2.6.16-rc2-ppc 2006-02-11 13:24:40.000000000 +0000
@@ -1,23 +1,25 @@
$ netcat -u -l -p 4444
-Total memory = 512MB; using 1024kB for hash table (at c0400000)
-Linux version 2.6.15.1 (rleigh@hardknott) (gcc version 4.0.3 20060115 (prerelease) (Debian 4.0.2-7)) #22 Wed Feb 8 20:44:14 GMT 2006
-Found UniNorth memory controller & host bridge, revision: 210
-Mapped at 0xfddf4000
-Found a Intrepid mac-io controller, rev: 0, mapped at 0xfdd74000
+Total memory = 512MB; using 1024kB for hash table (at cff00000)
+Linux version 2.6.16-rc2 (rleigh@hardknott) (gcc version 4.0.3 20060115 (prerelease) (Debian 4.0.2-7)) #4 Wed Feb 8 18:56:44 GMT 2006
+Found UniNorth memory controller & host bridge @ 0xf8000000 revision: 0xd2
+Mapped at 0xfdfc0000
+Found a Intrepid mac-io controller, rev: 0, mapped at 0xfdf40000
Processor NAP mode on idle enabled.
PowerMac motherboard: Mac mini
-Enabling clock spreading on Intrepid ASIC
+Using native/NAP idle loop
Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0
Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0
Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0
via-pmu: Server Mode is disabled
-PMU driver 2 initialized for Core99, firmware: 55
+PMU driver v2 initialized for Core99, firmware: 55
nvram: Checking bank 0...
nvram: gen0=470, gen1=469
nvram: Active bank is: 0
nvram: OF partition at 0x410
nvram: XP partition at 0x1020
nvram: NR partition at 0x1120
+Top of RAM: 0x20000000, Total RAM: 0x20000000
+Memory hole size: 0MB
Built 1 zonelists
Kernel command line: root=/dev/hda3 ro video=radeonfb:1680x1050-32@60 netconsole=@1/,4444@10.0.0.12/
netconsole: local port 6665
@@ -26,17 +28,17 @@
netconsole: remote port 4444
netconsole: remote IP 10.0.0.12
netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
-PowerMac using OpenPIC irq controller at 0x80040000
-OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc523000
-OpenPIC timer frequency is 4.166666 MHz
+mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs
+mpic: ISU size: 64, shift: 6, mask: 3f
+mpic: Initializing for 64 sources
PID hash table entries: 4096 (order: 12, 65536 bytes)
GMT Delta read from XPRAM: 0 minutes, DST: off
time_init: decrementer frequency = 41.620997 MHz
+time_init: processor frequency = 1416.666661 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
-Memory: 514048k available (2696k kernel code, 1044k data, 164k init, 0k highmem)
-AGP special page: 0xdffff000
+Memory: 514048k/524288k available (2996k kernel code, 9744k reserved, 308k data, 190k bss, 148k init)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
@@ -45,6 +47,55 @@
Mount-cache hash table entries: 512
device-tree: property "l2-cache" name conflicts with node in /cpus/PowerPC,G4@0
NET: Registered protocol family 16
+KeyWest i2c @0xf8001003 irq 42 /uni-n@f8000000/i2c@f8001000
+ channel 0 bus <multibus>
+ channel 1 bus <multibus>
+KeyWest i2c @0x80018000 irq 26 /pci@f2000000/mac-io@17/i2c@18000
+ channel 0 bus <multibus>
+PMU i2c /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c
+ channel 1 bus <multibus>
+ channel 2 bus <multibus>
+pmf: registering driver for node /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c/temp-monitor@190
+pmf: no functions, disposing..
+Installing base platform functions...
+Installing MMIO functions for macio /pci@f2000000/mac-io@17
+pmf: registering driver for node /pci@f2000000/mac-io@17
+pmf: Adding functions for platform-do-wor-enable
+pmf: idx 1: flags=08000000, phandle=ff97f4d0 16 bytes remaining, parsing...
+pmf: Added 1 functions
+pmf: Adding functions for platform-do-wor-disable
+pmf: idx 1: flags=08000000, phandle=ff97f4d0 16 bytes remaining, parsing...
+pmf: Added 1 functions
+Installing GPIO functions for macio /pci@f2000000/mac-io@17
+pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/modem-reset@1d
+pmf: Adding functions for platform-do-modem-reset
+pmf: idx 1: flags=08000000, phandle=ff975e48 12 bytes remaining, parsing...
+pmf: Added 1 functions
+pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/modem-power@1c
+pmf: Adding functions for platform-do-modem-power
+pmf: idx 1: flags=08000000, phandle=ff975e48 40 bytes remaining, parsing...
+pmf: Added 1 functions
+pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/extint-gpio1@9
+pmf: no functions, disposing..
+pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/programmer-switch@11
+pmf: no functions, disposing..
+pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/gpio5@6f
+pmf: no functions, disposing..
+pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/gpio6@70
+pmf: no functions, disposing..
+pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/extint-gpio15@67
+pmf: no functions, disposing..
+Calling initial GPIO functions for macio /pci@f2000000/mac-io@17
+Installing functions for UniN /uni-n@f8000000
+pmf: registering driver for node /uni-n@f8000000
+pmf: no functions, disposing..
+Installing functions for UniN clock /uni-n@f8000000/hw-clock
+pmf: registering driver for node /uni-n@f8000000/hw-clock
+pmf: Adding functions for platform-do-clockspreading
+pmf: idx 1: flags=20000000, phandle=00000000 56 bytes remaining, parsing...
+pmf: idx 2: flags=10000000, phandle=00000000 16 bytes remaining, parsing...
+pmf: Added 2 functions
+All base functions installed
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 0 of device 0001:10:18.0
PCI: Cannot allocate resource region 0 of device 0001:10:19.0
@@ -55,16 +106,16 @@
usbcore: registered new driver hub
Thermal assist unit not available
audit: initializing netlink socket (disabled)
-audit(1139431511.116:1): initialized
+audit(1139426338.104:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
-io scheduler cfq registered
+io scheduler cfq registered (default)
PCI: Enabling device 0000:00:10.0 (0006 -> 0007)
-radeonfb: Retreived PLL infos from Open Firmware
+radeonfb: Retrieved PLL infos from Open Firmware
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=190.00 Mhz, System=250.00 MHz
radeonfb: PLL min 12000 max 35000
radeonfb: Monitor 1 type DFP found
@@ -79,8 +130,8 @@
agpgart: Detected Apple UniNorth 2 chipset
agpgart: configuring for size idx: 4
agpgart: AGP aperture is 16M @ 0x0
-[drm] Initialized drm 1.0.0 20040925
-[drm] Initialized radeon 1.19.0 20050911 on minor 0:
+[drm] Initialized drm 1.0.1 20051102
+[drm] Initialized radeon 1.21.0 20051229 on minor 0
sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:11:24:75:6d:56
eth0: Found BCM5221 PHY
@@ -89,25 +140,23 @@
eth0: Pause is disabled
netconsole: network logging started
MacIO PCI driver attached to Intrepid chipset
-input: Macintosh mouse button emulation as /class/input/input0
-apm_emu: APM Emulation 0.5 initialized.
adb: starting probe task...
adb: finished probe task...
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
+ide0: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24
PCI: Enabling device 0002:20:0d.0 (0000 -> 0002)
-ide0: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39
-hda: TOSHIBA MK8025GAS, ATA DISK drive
-hdb: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive
-hda: Enabling Ultra DMA 5
-hdb: Enabling Ultra DMA 2
-ide0 at 0xe1022000-0xe1022007,0xe1022160 on irq 39
-ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24
-hda: max request size: 1024KiB
-hda: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100)
-hda: cache flushes supported
- hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7
-hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
+ide1: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39
+hdc: TOSHIBA MK8025GAS, ATA DISK drive
+hdd: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive
+hdc: Enabling Ultra DMA 5
+hdd: Enabling Ultra DMA 2
+ide1 at 0xe102a000-0xe102a007,0xe102a160 on irq 39
+hdc: max request size: 512KiB
+hdc: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100)
+hdc: cache flushes supported
+ hdc: [mac] hdc1 hdc2 hdc3 hdc4 hdc5 hdc6 hdc7
+hdd: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
usbmon: debugfs is not available
PCI: Enabling device 0001:10:1b.2 (0004 -> 0006)
@@ -116,8 +165,9 @@
ehci_hcd 0001:10:1b.2: irq 63, io mem 0x80080000
ehci_hcd 0001:10:1b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: EHCI Host Controller
-usb usb1: Manufacturer: Linux 2.6.15.1 ehci_hcd
+usb usb1: Manufacturer: Linux 2.6.16-rc2 ehci_hcd
usb usb1: SerialNumber: 0001:10:1b.2
+usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
Apple USB OHCI 0001:10:18.0 disabled by firmware
@@ -127,8 +177,9 @@
ohci_hcd 0001:10:1a.0: new USB bus registered, assigned bus number 2
ohci_hcd 0001:10:1a.0: irq 29, io mem 0x80083000
usb usb2: Product: OHCI Host Controller
-usb usb2: Manufacturer: Linux 2.6.15.1 ohci_hcd
+usb usb2: Manufacturer: Linux 2.6.16-rc2 ohci_hcd
usb usb2: SerialNumber: 0001:10:1a.0
+usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Enabling device 0001:10:1b.0 (0000 -> 0002)
@@ -137,10 +188,12 @@
ohci_hcd 0001:10:1b.0: irq 63, io mem 0x80082000
usb 1-2: new high speed USB device using ehci_hcd and address 3
usb usb3: Product: OHCI Host Controller
-usb usb3: Manufacturer: Linux 2.6.15.1 ohci_hcd
+usb usb3: Manufacturer: Linux 2.6.16-rc2 ohci_hcd
usb usb3: SerialNumber: 0001:10:1b.0
+usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
+usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 3 ports detected
PCI: Enabling device 0001:10:1b.1 (0000 -> 0002)
@@ -148,36 +201,56 @@
ohci_hcd 0001:10:1b.1: new USB bus registered, assigned bus number 4
ohci_hcd 0001:10:1b.1: irq 63, io mem 0x80081000
usb usb4: Product: OHCI Host Controller
-usb usb4: Manufacturer: Linux 2.6.15.1 ohci_hcd
+usb usb4: Manufacturer: Linux 2.6.16-rc2 ohci_hcd
usb usb4: SerialNumber: 0001:10:1b.1
+usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v2.3
Initializing USB Mass Storage driver...
-usbcore: registered new driver usb-storage
-USB Mass Storage support registered.
usb 3-1: new full speed USB device using ohci_hcd and address 2
usb 3-1: Product: Hub in Apple Extended USB Keyboard
usb 3-1: Manufacturer: Mitsumi Electric
+usb 3-1: configuration #1 chosen from 1 choice
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 3 ports detected
-usbcore: registered new driver hiddev
usb 1-2.2: new low speed USB device using ehci_hcd and address 4
usb 1-2.2: Product: Microsoft 3-Button Mouse with IntelliEye(TM)
usb 1-2.2: Manufacturer: Microsoft
+usb 1-2.2: configuration #1 chosen from 1 choice
usb 1-2.3: new low speed USB device using ehci_hcd and address 5
usb 1-2.3: Product: Apple Cinema Display
-input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input1
+usb 1-2.3: configuration #1 chosen from 1 choice
+usb 3-1.1: new full speed USB device using ohci_hcd and address 3
+usb 3-1.1: Product: USB DRIVE
+usb 3-1.1: Manufacturer: KINGSTON
+usb 3-1.1: SerialNumber: 1120046114165
+usb 3-1.1: configuration #1 chosen from 1 choice
+usb 3-1.3: new full speed USB device using ohci_hcd and address 4
+usb 3-1.3: Product: Apple Extended USB Keyboard
+usb 3-1.3: Manufacturer: Mitsumi Electric
+usb 3-1.3: configuration #1 chosen from 1 choice
+scsi0 : SCSI emulation for USB Mass Storage devices
+usbcore: registered new driver usb-storage
+USB Mass Storage support registered.
+usbcore: registered new driver hiddev
+input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input0
input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0001:10:1b.2-2.2
hiddev0: USB HID v1.11 Device [Apple Cinema Display] on usb-0001:10:1b.2-2.3
+input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input1
+input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3
+input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input2
+input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
-Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits
-Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits
-device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
-dmasound_pmac: couldn't find a Codec we can handle
+PowerMac i2c bus pmu 2 registered
+PowerMac i2c bus pmu 1 registered
+PowerMac i2c bus mac-io 0 registered
+PowerMac i2c bus uni-n 1 registered
+PowerMac i2c bus uni-n 0 registered
+device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
@@ -189,111 +262,7 @@
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
-kjournald starting. Commit interval 5 seconds
-EXT3-fs: mounted filesystem with ordered data mode.
-VFS: Mounted root (ext3 filesystem) readonly.
-Freeing unused kernel memory: 164k init
-usb 3-1.1: new full speed USB device using ohci_hcd and address 3
-usb 3-1.1: Product: USB DRIVE
-usb 3-1.1: Manufacturer: KINGSTON
-usb 3-1.1: SerialNumber: 1120046114165
-scsi0 : SCSI emulation for USB Mass Storage devices
-usb 3-1.3: new full speed USB device using ohci_hcd and address 4
-usb 3-1.3: Product: Apple Extended USB Keyboard
-usb 3-1.3: Manufacturer: Mitsumi Electric
-input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input2
-input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3
-input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input3
-input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3
-ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
-PCI: Enabling device 0002:20:0e.0 (0000 -> 0002)
-ohci1394: fw-host0: Unexpected PCI resource length of 1000!
-ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[2048]
- Vendor: KINGSTON Model: USB DRIVE Rev: 1.12
- Type: Direct-Access ANSI SCSI revision: 01 CCS
-SCSI device sda: 251904 512-byte hdwr sectors (129 MB)
-sda: Write Protect is off
-sda: assuming drive cache: write through
-hda: Enabling Ultra DMA 5
-SCSI device sda: 251904 512-byte hdwr sectors (129 MB)
-sda: Write Protect is off
-sda: assuming drive cache: write through
- sda:<7>usb-storage: queuecommand called
- sda1 sda2
-sd 0:0:0:0: Attached scsi removable disk sda
-eth1394: $Rev: 1312 $ Ben Collins <bcollins@debian.org>
-eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
-hda: Enabling Ultra DMA 5
-EXT3 FS on hda3, internal journal
-sbp2: $Rev: 1306 $ Ben Collins <bcollins@debian.org>
-ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
-ieee1394: sbp2: Try serialize_io=0 for better performance
-input: PowerMac Beep as /class/input/input4
-device-mapper: snapshot is marked invalid
-kjournald starting. Commit interval 5 seconds
-EXT3 FS on dm-5, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-kjournald starting. Commit interval 5 seconds
-EXT3 FS on dm-3, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-kjournald starting. Commit interval 5 seconds
-EXT3 FS on dm-4, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-kjournald starting. Commit interval 5 seconds
-EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
-EXT3 FS on dm-6, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-HFS+-fs: write access to a jounaled filesystem is not supported, use the force option at your own risk, mounting read-only.
-kjournald starting. Commit interval 5 seconds
-EXT3 FS on dm-7, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-kjournald starting. Commit interval 5 seconds
-EXT3 FS on dm-9, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-kjournald starting. Commit interval 5 seconds
-EXT3 FS on dm-14, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-Adding 2097144k swap on /dev/mapper/hda_vg-swap0. Priority:2 extents:1 across:2097144k
-Adding 2097144k swap on /dev/mapper/hda_vg-swap1. Priority:1 extents:1 across:2097144k
-Adding 2097144k swap on /dev/mapper/hda_vg-swap2. Priority:3 extents:1 across:2097144k
-NET: Registered protocol family 17
-sixxs: Disabled Privacy Extensions
-Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
-NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
-NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
-NFSD: starting 90-second grace period
-agpgart: Putting AGP V2 device at 0000:00:0b.0 into 1x mode
-agpgart: Putting AGP V2 device at 0000:00:10.0 into 1x mode
-[drm] Loading R200 Microcode
-usb 3-1: USB disconnect, address 2
-usb 3-1.1: USB disconnect, address 3
-usb 3-1.3: USB disconnect, address 4
-usb 3-1: new full speed USB device using ohci_hcd and address 5
-usb 3-1: Product: Hub in Apple Extended USB Keyboard
-usb 3-1: Manufacturer: Mitsumi Electric
-hub 3-1:1.0: USB hub found
-hub 3-1:1.0: 3 ports detected
-usb 3-1.1: new full speed USB device using ohci_hcd and address 6
-usb 3-1.1: Product: USB DRIVE
-usb 3-1.1: Manufacturer: KINGSTON
-usb 3-1.1: SerialNumber: 1120046114165
-scsi1 : SCSI emulation for USB Mass Storage devices
-usb 3-1.3: new full speed USB device using ohci_hcd and address 7
-usb 3-1.3: Product: Apple Extended USB Keyboard
-usb 3-1.3: Manufacturer: Mitsumi Electric
-input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input5
-input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3
-input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input6
-input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3
-usbcore: registered new driver ub
- Vendor: KINGSTON Model: USB DRIVE Rev: 1.12
- Type: Direct-Access ANSI SCSI revision: 01 CCS
-SCSI device sda: 251904 512-byte hdwr sectors (129 MB)
-sda: Write Protect is off
-sda: assuming drive cache: write through
-SCSI device sda: 251904 512-byte hdwr sectors (129 MB)
-sda: Write Protect is off
-sda: assuming drive cache: write through
- sda:<7>usb-storage: queuecommand called
- sda1 sda2
-sd 1:0:0:0: Attached scsi removable disk sda
+VFS: Cannot open root device "hda3" or unknown-block(0,0)
+Please append a correct "root=" boot option
+Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
+ <0>Rebooting in 180 seconds..<7>eth0: no IPv6 routers present
[-- Attachment #2: Type: application/pgp-signature, Size: 188 bytes --]
^ permalink raw reply [flat|nested] 3+ messages in thread