Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Thomas Gleixner]

On Tue, 2007-09-25 at 10:14 +0400, Mikhail Kshevetskiy wrote:
> Hello Thomas, Rafael
> 
> > We know, that
> > - disabling local apic timers work
> 
> As i can see from the log, you are booting on computer with dualcore AMD
> processor. Do you have C1E feature enabled? 
> 
> i386 kernel disable lapic on dualcore AMD with C1E support (see 
> http://lkml.org/lkml/2007/3/29/199). x86_64 kernel do not have this
> patch still (it's required for tickless kernel only).

Well it is required for non tickless mode as well.

>  As result, if
> you run x86_64 kernel with hrt patch on such computer, the system
> will stall during boot on lapic timer calibration.

Thanks for the reminder. I have a look into this.

	tglx

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Thomas Gleixner]

Rafael,

On Tue, 2007-09-25 at 10:07 +0200, Thomas Gleixner wrote:
> On Tue, 2007-09-25 at 10:14 +0400, Mikhail Kshevetskiy wrote:
> > Hello Thomas, Rafael
> > 
> > > We know, that
> > > - disabling local apic timers work
> > 
> > As i can see from the log, you are booting on computer with dualcore AMD
> > processor. Do you have C1E feature enabled? 
> > 
> > i386 kernel disable lapic on dualcore AMD with C1E support (see 
> > http://lkml.org/lkml/2007/3/29/199). x86_64 kernel do not have this
> > patch still (it's required for tickless kernel only).
> 
> Well it is required for non tickless mode as well.
> 
> >  As result, if
> > you run x86_64 kernel with hrt patch on such computer, the system
> > will stall during boot on lapic timer calibration.
> 
> Thanks for the reminder. I have a look into this.

Can you please boot mainline and provide the output of:

# cat /proc/interrupts; sleep 10; cat /proc/interrupts

Thanks,

	tglx

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

Thomas,

On Tuesday, 25 September 2007 11:30, Thomas Gleixner wrote:
> Rafael,
> 
> On Tue, 2007-09-25 at 10:07 +0200, Thomas Gleixner wrote:
> > On Tue, 2007-09-25 at 10:14 +0400, Mikhail Kshevetskiy wrote:
> > > Hello Thomas, Rafael
> > > 
> > > > We know, that
> > > > - disabling local apic timers work
> > > 
> > > As i can see from the log, you are booting on computer with dualcore AMD
> > > processor. Do you have C1E feature enabled? 

That's possible, how to check?

> > > i386 kernel disable lapic on dualcore AMD with C1E support (see 
> > > http://lkml.org/lkml/2007/3/29/199). x86_64 kernel do not have this
> > > patch still (it's required for tickless kernel only).
> > 
> > Well it is required for non tickless mode as well.
> > 
> > >  As result, if
> > > you run x86_64 kernel with hrt patch on such computer, the system
> > > will stall during boot on lapic timer calibration.
> > 
> > Thanks for the reminder. I have a look into this.
> 
> Can you please boot mainline and provide the output of:
> 
> # cat /proc/interrupts; sleep 10; cat /proc/interrupts

albercik:~ # cat /proc/interrupts; sleep 10; cat /proc/interrupts
           CPU0       CPU1
  0:    1159492          0  local-APIC-edge      timer
  1:       6892       1692   IO-APIC-edge      i8042
  8:          0          0   IO-APIC-edge      rtc
 12:        156        110   IO-APIC-edge      i8042
 14:      29613      11409   IO-APIC-edge      ide0
 16:      23365      21934   IO-APIC-fasteoi   sata_sil, HDA Intel
 18:        196      88386   IO-APIC-fasteoi   bcm43xx
 19:     744874     279433   IO-APIC-fasteoi   ohci_hcd:usb1, ohci_hcd:usb2, ehci_hcd:usb3
 20:          2          4   IO-APIC-fasteoi   ohci1394, yenta, tifm_7xx1, sdhci:slot0
 21:       1408        592   IO-APIC-fasteoi   acpi
NMI:          0          0   Non-maskable interrupts
LOC:          0    1158220   Local interrupts
RES:     260520     295387   Rescheduling interrupts
CAL:        419        652   function call interrupts
TLB:        864        541   TLB shootdowns
TRM:          0          0   Thermal event interrupts
THR:          0          0   Threshold APIC interrupts
SPU:          0          0   Spurious interrupts
ERR:         13
           CPU0       CPU1
  0:    1161996          0  local-APIC-edge      timer
  1:       6893       1692   IO-APIC-edge      i8042
  8:          0          0   IO-APIC-edge      rtc
 12:        156        110   IO-APIC-edge      i8042
 14:      29703      11409   IO-APIC-edge      ide0
 16:      23393      21934   IO-APIC-fasteoi   sata_sil, HDA Intel
 18:        196      88490   IO-APIC-fasteoi   bcm43xx
 19:     747268     279433   IO-APIC-fasteoi   ohci_hcd:usb1, ohci_hcd:usb2, ehci_hcd:usb3
 20:          2          4   IO-APIC-fasteoi   ohci1394, yenta, tifm_7xx1, sdhci:slot0
 21:       1412        592   IO-APIC-fasteoi   acpi
NMI:          0          0   Non-maskable interrupts
LOC:          0    1160723   Local interrupts
RES:     260567     295433   Rescheduling interrupts
CAL:        419        652   function call interrupts
TLB:        866        543   TLB shootdowns
TRM:          0          0   Thermal event interrupts
THR:          0          0   Threshold APIC interrupts
SPU:          0          0   Spurious interrupts
ERR:         13
albercik:~ #

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Thomas Gleixner]

On Tue, 2007-09-25 at 14:20 +0200, Rafael J. Wysocki wrote:
> > > > As i can see from the log, you are booting on computer with dualcore AMD
> > > > processor. Do you have C1E feature enabled? 
> 
> That's possible, how to check?
> 
> > > > i386 kernel disable lapic on dualcore AMD with C1E support (see 
> > > > http://lkml.org/lkml/2007/3/29/199). x86_64 kernel do not have this
> > > > patch still (it's required for tickless kernel only).
> > > 
> > > Well it is required for non tickless mode as well.
> > > 
> > > >  As result, if
> > > > you run x86_64 kernel with hrt patch on such computer, the system
> > > > will stall during boot on lapic timer calibration.
> > > 
> > > Thanks for the reminder. I have a look into this.
> > 
> > Can you please boot mainline and provide the output of:
> > 
> > # cat /proc/interrupts; sleep 10; cat /proc/interrupts
> 
> albercik:~ # cat /proc/interrupts; sleep 10; cat /proc/interrupts
>            CPU0       CPU1
>   0:    1159492          0  local-APIC-edge      timer
> LOC:          0    1158220   Local interrupts
>
>   0:    1161996          0  local-APIC-edge      timer
> LOC:          0    1160723   Local interrupts

Hmm. That's strange. It looks like the local apic timer is not used, but
x86_64 definitely lacks the above check. Can you please remove/disable
the acpi processor module and recheck ?

	tglx

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

On Tuesday, 25 September 2007 14:28, Thomas Gleixner wrote:
> On Tue, 2007-09-25 at 14:20 +0200, Rafael J. Wysocki wrote:
> > > > > As i can see from the log, you are booting on computer with dualcore AMD
> > > > > processor. Do you have C1E feature enabled? 
> > 
> > That's possible, how to check?
> > 
> > > > > i386 kernel disable lapic on dualcore AMD with C1E support (see 
> > > > > http://lkml.org/lkml/2007/3/29/199). x86_64 kernel do not have this
> > > > > patch still (it's required for tickless kernel only).
> > > > 
> > > > Well it is required for non tickless mode as well.
> > > > 
> > > > >  As result, if
> > > > > you run x86_64 kernel with hrt patch on such computer, the system
> > > > > will stall during boot on lapic timer calibration.
> > > > 
> > > > Thanks for the reminder. I have a look into this.
> > > 
> > > Can you please boot mainline and provide the output of:
> > > 
> > > # cat /proc/interrupts; sleep 10; cat /proc/interrupts
> > 
> > albercik:~ # cat /proc/interrupts; sleep 10; cat /proc/interrupts
> >            CPU0       CPU1
> >   0:    1159492          0  local-APIC-edge      timer
> > LOC:          0    1158220   Local interrupts
> >
> >   0:    1161996          0  local-APIC-edge      timer
> > LOC:          0    1160723   Local interrupts
> 
> Hmm. That's strange. It looks like the local apic timer is not used, but
> x86_64 definitely lacks the above check.

Ouch, sorry.  This is from the kernel booted with "noapictimer".

I'll get the correct output in a little while.

Greetings,
Rafael

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

On Tuesday, 25 September 2007 14:52, Rafael J. Wysocki wrote:
> On Tuesday, 25 September 2007 14:28, Thomas Gleixner wrote:
> > On Tue, 2007-09-25 at 14:20 +0200, Rafael J. Wysocki wrote:
> > > > > > As i can see from the log, you are booting on computer with dualcore AMD
> > > > > > processor. Do you have C1E feature enabled? 
> > > 
> > > That's possible, how to check?
> > > 
> > > > > > i386 kernel disable lapic on dualcore AMD with C1E support (see 
> > > > > > http://lkml.org/lkml/2007/3/29/199). x86_64 kernel do not have this
> > > > > > patch still (it's required for tickless kernel only).
> > > > > 
> > > > > Well it is required for non tickless mode as well.
> > > > > 
> > > > > >  As result, if
> > > > > > you run x86_64 kernel with hrt patch on such computer, the system
> > > > > > will stall during boot on lapic timer calibration.
> > > > > 
> > > > > Thanks for the reminder. I have a look into this.
> > > > 
> > > > Can you please boot mainline and provide the output of:
> > > > 
> > > > # cat /proc/interrupts; sleep 10; cat /proc/interrupts
> > > 
> > > albercik:~ # cat /proc/interrupts; sleep 10; cat /proc/interrupts
> > >            CPU0       CPU1
> > >   0:    1159492          0  local-APIC-edge      timer
> > > LOC:          0    1158220   Local interrupts
> > >
> > >   0:    1161996          0  local-APIC-edge      timer
> > > LOC:          0    1160723   Local interrupts
> > 
> > Hmm. That's strange. It looks like the local apic timer is not used, but
> > x86_64 definitely lacks the above check.
> 
> Ouch, sorry.  This is from the kernel booted with "noapictimer".
> 
> I'll get the correct output in a little while.

OK, this one is from -rc7 with no extra command line:

albercik:~ # cat /proc/interrupts; sleep 10; cat /proc/interrupts
           CPU0       CPU1
  0:      27311          0  local-APIC-edge      timer
  1:          1         77   IO-APIC-edge      i8042
  8:          0          0   IO-APIC-edge      rtc
 12:          0        148   IO-APIC-edge      i8042
 14:         19        683   IO-APIC-edge      ide0
 16:        178      12443   IO-APIC-fasteoi   sata_sil, HDA Intel
 19:        111      15197   IO-APIC-fasteoi   ehci_hcd:usb1, ohci_hcd:usb2, ohci_hcd:usb3
 20:          0          3   IO-APIC-fasteoi   tifm_7xx1, yenta, sdhci:slot0, ohci1394
 21:          0        113   IO-APIC-fasteoi   acpi
NMI:          0          0
LOC:      27270      27119
ERR:          2
           CPU0       CPU1
  0:      29815          0  local-APIC-edge      timer
  1:          1         77   IO-APIC-edge      i8042
  8:          0          0   IO-APIC-edge      rtc
 12:          0        148   IO-APIC-edge      i8042
 14:         20        772   IO-APIC-edge      ide0
 16:        178      12451   IO-APIC-fasteoi   sata_sil, HDA Intel
 19:        112      17199   IO-APIC-fasteoi   ehci_hcd:usb1, ohci_hcd:usb2, ohci_hcd:usb3
 20:          0          3   IO-APIC-fasteoi   tifm_7xx1, yenta, sdhci:slot0, ohci1394
 21:          0        117   IO-APIC-fasteoi   acpi
NMI:          0          0
LOC:      29774      29623
ERR:          2
albercik:~ #

Greetings,
Rafael

2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

Hi Thomas,

Unfortunately, my observation that the patch series:

http://tglx.de/projects/hrtimers/2.6.23-rc4/patch-2.6.23-rc4-hrt1.patches.tar.bz2

worked with 2.6.23-rc4 was wrong.  It _sometimes_ works, but usually doesn't
boot, just like 2.6.23-rc4-mm1, 2.6.23-rc6-mm1 and everything in between with
the above patch series applied.  I've also tried:

http://tglx.de/projects/hrtimers/2.6.23-rc5/patch-2.6.23-rc5-hrt1.patches.tar.bz2
http://tglx.de/projects/hrtimers/2.6.23-rc6/patch-2.6.23-rc6-hrt2.patch

with the same result.

The problematic patch is x86_64-convert-to-clockevents.patch .

Since the boot fails very early, before any messages reach the (VGA) console,
I have no idea what to do next, except for digging in the code.

Greetings,
Rafael

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Thomas Gleixner]

On Sun, 2007-09-23 at 12:57 +0200, Rafael J. Wysocki wrote:
> Hi Thomas,
> 
> Unfortunately, my observation that the patch series:
> 
> http://tglx.de/projects/hrtimers/2.6.23-rc4/patch-2.6.23-rc4-hrt1.patches.tar.bz2
> 
> worked with 2.6.23-rc4 was wrong.  It _sometimes_ works, but usually doesn't
> boot, just like 2.6.23-rc4-mm1, 2.6.23-rc6-mm1 and everything in between with
> the above patch series applied.  I've also tried:
> 
> http://tglx.de/projects/hrtimers/2.6.23-rc5/patch-2.6.23-rc5-hrt1.patches.tar.bz2
> http://tglx.de/projects/hrtimers/2.6.23-rc6/patch-2.6.23-rc6-hrt2.patch
> 
> with the same result.
> 
> The problematic patch is x86_64-convert-to-clockevents.patch .
> 
> Since the boot fails very early, before any messages reach the (VGA) console,
> I have no idea what to do next, except for digging in the code.

Ok, lets track it down. Is there any difference when you add:

nohz=off
highres=off
noapictimer

or any combinations of the above to the kernel command line ?

	tglx

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

[-- Attachment #1: Type: text/plain, Size: 1399 bytes --]

On Sunday, 23 September 2007 21:10, Thomas Gleixner wrote:
> On Sun, 2007-09-23 at 12:57 +0200, Rafael J. Wysocki wrote:
> > Hi Thomas,
> > 
> > Unfortunately, my observation that the patch series:
> > 
> > http://tglx.de/projects/hrtimers/2.6.23-rc4/patch-2.6.23-rc4-hrt1.patches.tar.bz2
> > 
> > worked with 2.6.23-rc4 was wrong.  It _sometimes_ works, but usually doesn't
> > boot, just like 2.6.23-rc4-mm1, 2.6.23-rc6-mm1 and everything in between with
> > the above patch series applied.  I've also tried:
> > 
> > http://tglx.de/projects/hrtimers/2.6.23-rc5/patch-2.6.23-rc5-hrt1.patches.tar.bz2
> > http://tglx.de/projects/hrtimers/2.6.23-rc6/patch-2.6.23-rc6-hrt2.patch
> > 
> > with the same result.
> > 
> > The problematic patch is x86_64-convert-to-clockevents.patch .
> > 
> > Since the boot fails very early, before any messages reach the (VGA) console,
> > I have no idea what to do next, except for digging in the code.
> 
> Ok, lets track it down. Is there any difference when you add:
> 
> nohz=off
> highres=off
> noapictimer
> 
> or any combinations of the above to the kernel command line ?

First, for now, I build all kernels with NO_HZ and HIGH_RES_TIMERS unset
(.config for 2.6.23-rc6-mm1 is attached).

Second, noacpitimer added to the command line makes all of the kernels, up to
and including 2.6.23-rc6-mm1, boot (this seems to be 100% reproducible).

Greetings,
Rafael

[-- Attachment #2: 2.6.23-rc6-mm1-config --]
[-- Type: text/plain, Size: 55973 bytes --]

#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.23-rc6-mm1
# Tue Sep 18 22:52:04 2007
#
CONFIG_X86_64=y
CONFIG_64BIT=y
CONFIG_X86=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_NONIRQ_WAKEUP=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_ZONE_DMA32=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
CONFIG_QUICKLIST=y
CONFIG_NR_QUICK=2
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_CMPXCHG=y
CONFIG_EARLY_PRINTK=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_DMI=y
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_BUG=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"

#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
CONFIG_TASKSTATS=y
CONFIG_TASK_DELAY_ACCT=y
# CONFIG_TASK_XACCT is not set
# CONFIG_USER_NS is not set
CONFIG_AUDIT=y
CONFIG_AUDITSYSCALL=y
CONFIG_AUDIT_TREE=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=18
# CONFIG_CONTAINERS is not set
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_PROC_KPAGEMAP=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_BLK_DEV_BSG is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"

#
# Processor type and features
#
# CONFIG_TICK_ONESHOT is not set
# CONFIG_NO_HZ is not set
# CONFIG_HIGH_RES_TIMERS is not set
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_X86_PC=y
# CONFIG_X86_VSMP is not set
CONFIG_MK8=y
# CONFIG_MPSC is not set
# CONFIG_MCORE2 is not set
# CONFIG_GENERIC_CPU is not set
CONFIG_X86_L1_CACHE_BYTES=64
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_INTERNODE_CACHE_BYTES=64
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
# CONFIG_MICROCODE is not set
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m
CONFIG_X86_IO_APIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_MTRR=y
CONFIG_SMP=y
# CONFIG_SCHED_SMT is not set
CONFIG_SCHED_MC=y
# CONFIG_PREEMPT_NONE is not set
CONFIG_PREEMPT_VOLUNTARY=y
# CONFIG_PREEMPT is not set
CONFIG_PREEMPT_BKL=y
# CONFIG_NUMA is not set
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_RESOURCES_64BIT=y
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_VIRT_TO_BUS=y
CONFIG_NR_CPUS=128
CONFIG_PHYSICAL_ALIGN=0x200000
CONFIG_HOTPLUG_CPU=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_IOMMU=y
# CONFIG_CALGARY_IOMMU is not set
CONFIG_SWIOTLB=y
CONFIG_X86_MCE=y
# CONFIG_X86_MCE_INTEL is not set
CONFIG_X86_MCE_AMD=y
CONFIG_KEXEC=y
# CONFIG_CRASH_DUMP is not set
# CONFIG_RELOCATABLE is not set
CONFIG_PHYSICAL_START=0x200000
CONFIG_SECCOMP=y
# CONFIG_CC_STACKPROTECTOR is not set
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
CONFIG_K8_NB=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_ISA_DMA_API=y
CONFIG_GENERIC_PENDING_IRQ=y

#
# Power management options
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
CONFIG_PM_DEBUG=y
# CONFIG_PM_VERBOSE is not set
CONFIG_PM_TRACE=y
CONFIG_PM_SLEEP_SMP=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND_SMP_POSSIBLE=y
CONFIG_SUSPEND=y
CONFIG_HIBERNATION_SMP_POSSIBLE=y
CONFIG_HIBERNATION=y
CONFIG_PM_STD_PARTITION=""
CONFIG_ARCH_HIBERNATION_HEADER=y
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_PROCFS=y
CONFIG_ACPI_PROC_EVENT=y
CONFIG_ACPI_AC=m
CONFIG_ACPI_BATTERY=m
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_VIDEO=m
CONFIG_ACPI_FAN=m
# CONFIG_ACPI_DOCK is not set
CONFIG_ACPI_PROCESSOR=m
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=m
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_TOSHIBA is not set
# CONFIG_ACPI_CUSTOM_DSDT is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
CONFIG_ACPI_DEBUG=y
# CONFIG_ACPI_DEBUG_FUNC_TRACE is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=y
# CONFIG_ACPI_SBS is not set

#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=m
CONFIG_CPU_FREQ_DEBUG=y
CONFIG_CPU_FREQ_STAT=m
CONFIG_CPU_FREQ_STAT_DETAILS=y
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
CONFIG_CPU_FREQ_GOV_USERSPACE=m
CONFIG_CPU_FREQ_GOV_ONDEMAND=m
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m

#
# CPUFreq processor drivers
#
CONFIG_X86_POWERNOW_K8=m
CONFIG_X86_POWERNOW_K8_ACPI=y
# CONFIG_X86_SPEEDSTEP_CENTRINO is not set
CONFIG_X86_ACPI_CPUFREQ=m

#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
# CONFIG_X86_SPEEDSTEP_LIB is not set

#
# CPU idle PM support
#
CONFIG_CPU_IDLE=y

#
# Governors
#
CONFIG_CPU_IDLE_GOV_LADDER=m

#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
# CONFIG_PCI_DOMAINS is not set
CONFIG_DMAR=y
CONFIG_DMAR_GFX_WA=y
CONFIG_DMAR_FLOPPY_WA=y
CONFIG_PCIEPORTBUS=y
CONFIG_HOTPLUG_PCI_PCIE=m
CONFIG_PCIEAER=y
CONFIG_ARCH_SUPPORTS_MSI=y
CONFIG_PCI_MSI=y
# CONFIG_PCI_DEBUG is not set
CONFIG_HT_IRQ=y
CONFIG_PCCARD=m
# CONFIG_PCMCIA_DEBUG is not set
CONFIG_PCMCIA=m
CONFIG_PCMCIA_LOAD_CIS=y
CONFIG_CARDBUS=y

#
# PC-card bridges
#
CONFIG_YENTA=m
CONFIG_YENTA_O2=y
CONFIG_YENTA_RICOH=y
CONFIG_YENTA_TI=y
CONFIG_YENTA_ENE_TUNE=y
CONFIG_YENTA_TOSHIBA=y
CONFIG_PD6729=m
CONFIG_I82092=m
CONFIG_PCCARD_NONSTATIC=m
CONFIG_HOTPLUG_PCI=m
CONFIG_HOTPLUG_PCI_FAKE=m
CONFIG_HOTPLUG_PCI_ACPI=m
CONFIG_HOTPLUG_PCI_ACPI_IBM=m
CONFIG_HOTPLUG_PCI_CPCI=y
CONFIG_HOTPLUG_PCI_CPCI_ZT5550=m
CONFIG_HOTPLUG_PCI_CPCI_GENERIC=m
CONFIG_HOTPLUG_PCI_SHPC=m

#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
CONFIG_IA32_EMULATION=y
CONFIG_IA32_AOUT=y
CONFIG_COMPAT=y
CONFIG_COMPAT_FOR_U64_ALIGNMENT=y
CONFIG_SYSVIPC_COMPAT=y

#
# Networking
#
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=m
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
CONFIG_NET_KEY=m
# CONFIG_NET_KEY_MIGRATE is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_TUNNEL=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=m
CONFIG_INET_LRO=m
CONFIG_INET_DIAG=m
CONFIG_INET_TCP_DIAG=m
CONFIG_TCP_CONG_ADVANCED=y
CONFIG_TCP_CONG_BIC=m
CONFIG_TCP_CONG_CUBIC=m
CONFIG_TCP_CONG_WESTWOOD=m
CONFIG_TCP_CONG_HTCP=m
CONFIG_TCP_CONG_HSTCP=m
CONFIG_TCP_CONG_HYBLA=m
CONFIG_TCP_CONG_VEGAS=m
CONFIG_TCP_CONG_SCALABLE=m
# CONFIG_TCP_CONG_LP is not set
# CONFIG_TCP_CONG_VENO is not set
CONFIG_TCP_CONG_YEAH=m
CONFIG_TCP_CONG_ILLINOIS=m
# CONFIG_DEFAULT_BIC is not set
# CONFIG_DEFAULT_CUBIC is not set
# CONFIG_DEFAULT_HTCP is not set
# CONFIG_DEFAULT_VEGAS is not set
# CONFIG_DEFAULT_WESTWOOD is not set
CONFIG_DEFAULT_RENO=y
CONFIG_DEFAULT_TCP_CONG="reno"
CONFIG_TCP_MD5SIG=y
# CONFIG_IP_VS is not set
CONFIG_IPV6=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
CONFIG_IPV6_ROUTE_INFO=y
CONFIG_IPV6_OPTIMISTIC_DAD=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
CONFIG_IPV6_MIP6=m
CONFIG_INET6_XFRM_TUNNEL=m
CONFIG_INET6_TUNNEL=m
CONFIG_INET6_XFRM_MODE_TRANSPORT=m
CONFIG_INET6_XFRM_MODE_TUNNEL=m
CONFIG_INET6_XFRM_MODE_BEET=m
CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
CONFIG_IPV6_SIT=m
CONFIG_IPV6_TUNNEL=m
CONFIG_IPV6_MULTIPLE_TABLES=y
CONFIG_IPV6_SUBTREES=y
CONFIG_NETLABEL=y
CONFIG_NETWORK_SECMARK=y
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set

#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_NETLINK=m
CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NETFILTER_NETLINK_LOG=m
CONFIG_NF_CONNTRACK_ENABLED=m
CONFIG_NF_CONNTRACK=m
CONFIG_NF_CT_ACCT=y
CONFIG_NF_CONNTRACK_MARK=y
CONFIG_NF_CONNTRACK_SECMARK=y
CONFIG_NF_CONNTRACK_EVENTS=y
CONFIG_NF_CT_PROTO_GRE=m
# CONFIG_NF_CT_PROTO_SCTP is not set
# CONFIG_NF_CT_PROTO_UDPLITE is not set
# CONFIG_NF_CONNTRACK_AMANDA is not set
CONFIG_NF_CONNTRACK_FTP=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
CONFIG_NF_CT_NETLINK=m
CONFIG_NETFILTER_XTABLES=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_SECMARK=m
CONFIG_NETFILTER_XT_TARGET_CONNSECMARK=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
CONFIG_NETFILTER_XT_MATCH_DCCP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HELPER=m
CONFIG_NETFILTER_XT_MATCH_LENGTH=m
CONFIG_NETFILTER_XT_MATCH_LIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_QUOTA=m
CONFIG_NETFILTER_XT_MATCH_REALM=m
CONFIG_NETFILTER_XT_MATCH_SCTP=m
CONFIG_NETFILTER_XT_MATCH_STATE=m
CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
CONFIG_NETFILTER_XT_MATCH_STRING=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_U32=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m

#
# IP: Netfilter Configuration
#
CONFIG_NF_CONNTRACK_IPV4=m
CONFIG_NF_CONNTRACK_PROC_COMPAT=y
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_NF_NAT=m
CONFIG_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_NF_NAT_PROTO_GRE=m
CONFIG_NF_NAT_FTP=m
CONFIG_NF_NAT_IRC=m
CONFIG_NF_NAT_TFTP=m
# CONFIG_NF_NAT_AMANDA is not set
CONFIG_NF_NAT_PPTP=m
CONFIG_NF_NAT_H323=m
CONFIG_NF_NAT_SIP=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_TTL=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m

#
# IPv6: Netfilter Configuration (EXPERIMENTAL)
#
CONFIG_NF_CONNTRACK_IPV6=m
CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_MATCH_OPTS=m
CONFIG_IP6_NF_MATCH_FRAG=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_OWNER=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_MH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_TARGET_HL=m
CONFIG_IP6_NF_RAW=m
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set

#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
CONFIG_NET_SCH_FIFO=y
CONFIG_NET_CLS_ROUTE=y

#
# Network testing
#
CONFIG_NET_PKTGEN=m
# CONFIG_NET_TCPPROBE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_HIDP=m

#
# Bluetooth device drivers
#
CONFIG_BT_HCIUSB=m
CONFIG_BT_HCIUSB_SCO=y
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
CONFIG_BT_HCIBCM203X=m
CONFIG_BT_HCIBPA10X=m
CONFIG_BT_HCIBFUSB=m
CONFIG_BT_HCIDTL1=m
CONFIG_BT_HCIBT3C=m
CONFIG_BT_HCIBLUECARD=m
CONFIG_BT_HCIBTUART=m
CONFIG_BT_HCIVHCI=m
# CONFIG_AF_RXRPC is not set
CONFIG_FIB_RULES=y

#
# Wireless
#
CONFIG_CFG80211=m
CONFIG_NL80211=y
CONFIG_WIRELESS_EXT=y
CONFIG_MAC80211=m
CONFIG_MAC80211_LEDS=y
CONFIG_MAC80211_DEBUGFS=y
CONFIG_MAC80211_DEBUG=y
# CONFIG_MAC80211_VERBOSE_DEBUG is not set
# CONFIG_MAC80211_LOWTX_FRAME_DUMP is not set
# CONFIG_TKIP_DEBUG is not set
# CONFIG_MAC80211_DEBUG_COUNTERS is not set
CONFIG_MAC80211_IBSS_DEBUG=y
# CONFIG_MAC80211_VERBOSE_PS_DEBUG is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_CRYPT_CCMP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
CONFIG_IEEE80211_SOFTMAC=m
CONFIG_IEEE80211_SOFTMAC_DEBUG=y
CONFIG_RFKILL=m
CONFIG_RFKILL_INPUT=m
# CONFIG_NET_9P is not set

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
# CONFIG_STANDALONE is not set
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=y
CONFIG_PROC_EVENTS=y
CONFIG_MTD=m
# CONFIG_MTD_DEBUG is not set
CONFIG_MTD_CONCAT=m
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_REDBOOT_PARTS=m
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set

#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=m
CONFIG_MTD_BLKDEVS=m
CONFIG_MTD_BLOCK=m
# CONFIG_MTD_BLOCK_RO is not set
# CONFIG_FTL is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
CONFIG_RFD_FTL=m
CONFIG_SSFDC=m
CONFIG_MTD_OOPS=m

#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=m
CONFIG_MTD_JEDECPROBE=m
CONFIG_MTD_GEN_PROBE=m
CONFIG_MTD_CFI_ADV_OPTIONS=y
CONFIG_MTD_CFI_NOSWAP=y
# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
# CONFIG_MTD_CFI_GEOMETRY is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
# CONFIG_MTD_OTP is not set
CONFIG_MTD_CFI_INTELEXT=m
CONFIG_MTD_CFI_AMDSTD=m
CONFIG_MTD_CFI_STAA=m
CONFIG_MTD_CFI_UTIL=m
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
CONFIG_MTD_ABSENT=m

#
# Mapping drivers for chip access
#
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=m
CONFIG_MTD_PHYSMAP_START=0x8000000
CONFIG_MTD_PHYSMAP_LEN=0x4000000
CONFIG_MTD_PHYSMAP_BANKWIDTH=2
# CONFIG_MTD_PNC2000 is not set
# CONFIG_MTD_SC520CDP is not set
# CONFIG_MTD_NETSC520 is not set
CONFIG_MTD_TS5500=m
# CONFIG_MTD_SBC_GXX is not set
CONFIG_MTD_AMD76XROM=m
CONFIG_MTD_ICHXROM=m
# CONFIG_MTD_ESB2ROM is not set
# CONFIG_MTD_CK804XROM is not set
CONFIG_MTD_SCB2_FLASH=m
# CONFIG_MTD_NETtel is not set
# CONFIG_MTD_DILNETPC is not set
# CONFIG_MTD_L440GX is not set
CONFIG_MTD_PCI=m
# CONFIG_MTD_PLATRAM is not set

#
# Self-contained MTD device drivers
#
CONFIG_MTD_PMC551=m
CONFIG_MTD_PMC551_BUGFIX=y
# CONFIG_MTD_PMC551_DEBUG is not set
# CONFIG_MTD_DATAFLASH is not set
# CONFIG_MTD_M25P80 is not set
CONFIG_MTD_SLRAM=m
CONFIG_MTD_PHRAM=m
CONFIG_MTD_MTDRAM=m
CONFIG_MTDRAM_TOTAL_SIZE=4096
CONFIG_MTDRAM_ERASE_SIZE=128
CONFIG_MTD_BLOCK2MTD=m

#
# Disk-On-Chip Device Drivers
#
CONFIG_MTD_DOC2000=m
CONFIG_MTD_DOC2001=m
CONFIG_MTD_DOC2001PLUS=m
CONFIG_MTD_DOCPROBE=m
CONFIG_MTD_DOCECC=m
CONFIG_MTD_DOCPROBE_ADVANCED=y
CONFIG_MTD_DOCPROBE_ADDRESS=0x0000
CONFIG_MTD_DOCPROBE_HIGH=y
CONFIG_MTD_DOCPROBE_55AA=y
CONFIG_MTD_NAND=m
# CONFIG_MTD_NAND_VERIFY_WRITE is not set
# CONFIG_MTD_NAND_ECC_SMC is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=m
CONFIG_MTD_NAND_DISKONCHIP=m
# CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED is not set
CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0
CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE=y
CONFIG_MTD_NAND_CAFE=m
CONFIG_MTD_NAND_NANDSIM=m
# CONFIG_MTD_NAND_PLATFORM is not set
CONFIG_MTD_ALAUDA=m
CONFIG_MTD_ONENAND=m
# CONFIG_MTD_ONENAND_VERIFY_WRITE is not set
# CONFIG_MTD_ONENAND_OTP is not set
# CONFIG_MTD_ONENAND_2X_PROGRAM is not set
# CONFIG_MTD_ONENAND_SIM is not set

#
# UBI - Unsorted block images
#
# CONFIG_MTD_UBI is not set
# CONFIG_PARPORT is not set
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set

#
# Protocols
#
CONFIG_PNPACPI=y
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_FD=m
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=128000
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
CONFIG_CDROM_PKTCDVD_WCACHE=y
# CONFIG_ATA_OVER_ETH is not set
CONFIG_MISC_DEVICES=y
# CONFIG_IBM_ASM is not set
CONFIG_PHANTOM=m
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_SGI_IOC4 is not set
CONFIG_TIFM_CORE=m
CONFIG_TIFM_7XX1=m
# CONFIG_ASUS_LAPTOP is not set
# CONFIG_FUJITSU_LAPTOP is not set
# CONFIG_MSI_LAPTOP is not set
# CONFIG_SONY_LAPTOP is not set
# CONFIG_THINKPAD_ACPI is not set
CONFIG_IDE=m
CONFIG_BLK_DEV_IDE=m

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=m
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECS=m
# CONFIG_BLK_DEV_DELKIN is not set
CONFIG_BLK_DEV_IDECD=m
CONFIG_BLK_DEV_IDETAPE=m
CONFIG_BLK_DEV_IDEFLOPPY=m
CONFIG_BLK_DEV_IDESCSI=m
CONFIG_BLK_DEV_IDEACPI=y
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_IDE_PROC_FS=y

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=m
CONFIG_BLK_DEV_PLATFORM=m
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_IDEPNP is not set

#
# PCI IDE chipsets support
#
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_IDEPCI_PCIBUS_ORDER is not set
CONFIG_BLK_DEV_OFFBOARD=y
CONFIG_BLK_DEV_GENERIC=m
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
CONFIG_BLK_DEV_ATIIXP=m
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_BLK_DEV_TC86C001 is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
CONFIG_RAID_ATTRS=m
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
CONFIG_SCSI_TGT=m
CONFIG_SCSI_NETLINK=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=m
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_CHR_DEV_SCH=m

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
# CONFIG_SCSI_SCAN_ASYNC is not set
CONFIG_SCSI_WAIT_SCAN=m

#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=m
CONFIG_SCSI_FC_ATTRS=m
# CONFIG_SCSI_FC_TGT_ATTRS is not set
CONFIG_SCSI_ISCSI_ATTRS=m
# CONFIG_SCSI_SAS_LIBSAS is not set
CONFIG_SCSI_SRP_ATTRS=m
CONFIG_SCSI_SRP_TGT_ATTRS=y
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
CONFIG_SCSI_DEBUG=m
CONFIG_SCSI_SRP=m
# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_ACPI=y
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_NV is not set
# CONFIG_PDC_ADMA is not set
# CONFIG_SATA_QSTOR is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
CONFIG_SATA_SIL=y
# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PCMCIA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=m
CONFIG_MD_RAID10=m
# CONFIG_MD_RAID456 is not set
CONFIG_MD_MULTIPATH=m
CONFIG_MD_FAULTY=m
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_MULTIPATH_EMC=m
CONFIG_DM_MULTIPATH_RDAC=m
# CONFIG_DM_DELAY is not set
# CONFIG_FUSION is not set

#
# IEEE 1394 (FireWire) support
#
# CONFIG_FIREWIRE is not set
CONFIG_IEEE1394=m

#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set

#
# Controllers
#
CONFIG_IEEE1394_PCILYNX=m
CONFIG_IEEE1394_OHCI1394=m

#
# Protocols
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
CONFIG_IEEE1394_SBP2_PHYS_DMA=y
CONFIG_IEEE1394_ETH1394_ROM_ENTRY=y
CONFIG_IEEE1394_ETH1394=m
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=m
CONFIG_I2O=m
CONFIG_I2O_LCT_NOTIFY_ON_CHANGES=y
CONFIG_I2O_EXT_ADAPTEC=y
CONFIG_I2O_EXT_ADAPTEC_DMA64=y
CONFIG_I2O_CONFIG=m
CONFIG_I2O_CONFIG_OLD_IOCTL=y
CONFIG_I2O_BUS=m
CONFIG_I2O_BLOCK=m
CONFIG_I2O_SCSI=m
CONFIG_I2O_PROC=m
# CONFIG_MACINTOSH_DRIVERS is not set
CONFIG_NETDEVICES=y
CONFIG_NETDEVICES_MULTIQUEUE=y
CONFIG_DUMMY=m
CONFIG_BONDING=m
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
# CONFIG_VETH is not set
# CONFIG_NET_SB1000 is not set
# CONFIG_IP1000 is not set
# CONFIG_ARCNET is not set
CONFIG_PHYLIB=m

#
# MII PHY device drivers
#
CONFIG_MARVELL_PHY=m
CONFIG_DAVICOM_PHY=m
CONFIG_QSEMI_PHY=m
CONFIG_LXT_PHY=m
CONFIG_CICADA_PHY=m
CONFIG_VITESSE_PHY=m
CONFIG_SMSC_PHY=m
CONFIG_BROADCOM_PHY=m
# CONFIG_ICPLUS_PHY is not set
CONFIG_FIXED_PHY=m
CONFIG_FIXED_MII_10_FDX=y
CONFIG_FIXED_MII_100_FDX=y
CONFIG_FIXED_MII_1000_FDX=y
CONFIG_FIXED_MII_AMNT=1
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_NET_PCI is not set
CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_E1000E is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
CONFIG_TIGON3=m
CONFIG_BNX2=m
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set

#
# Wireless LAN
#
# CONFIG_WLAN_PRE80211 is not set
CONFIG_WLAN_80211=y
# CONFIG_PCMCIA_RAYCS is not set
# CONFIG_IPW2100 is not set
# CONFIG_IPW2200 is not set
# CONFIG_LIBERTAS is not set
# CONFIG_AIRO is not set
# CONFIG_HERMES is not set
# CONFIG_USB_ATMEL is not set
# CONFIG_ATMEL is not set
# CONFIG_AIRO_CS is not set
# CONFIG_PCMCIA_WL3501 is not set
# CONFIG_PRISM54 is not set
# CONFIG_USB_ZD1201 is not set
# CONFIG_RTL8187 is not set
# CONFIG_ADM8211 is not set
# CONFIG_P54_COMMON is not set
# CONFIG_HOSTAP is not set
CONFIG_BCM43XX=m
CONFIG_BCM43XX_DEBUG=y
CONFIG_BCM43XX_DMA=y
CONFIG_BCM43XX_PIO=y
CONFIG_BCM43XX_DMA_AND_PIO_MODE=y
# CONFIG_BCM43XX_DMA_MODE is not set
# CONFIG_BCM43XX_PIO_MODE is not set
CONFIG_B43=m
CONFIG_B43_PCI_AUTOSELECT=y
CONFIG_B43_PCICORE_AUTOSELECT=y
# CONFIG_B43_PCMCIA is not set
CONFIG_B43_DEBUG=y
CONFIG_B43_DMA=y
CONFIG_B43_PIO=y
CONFIG_B43_DMA_AND_PIO_MODE=y
# CONFIG_B43_DMA_MODE is not set
# CONFIG_B43_PIO_MODE is not set
# CONFIG_B43LEGACY is not set
# CONFIG_ZD1211RW is not set
# CONFIG_RT2X00 is not set
# CONFIG_ZD1211RW_MAC80211 is not set

#
# USB Network Adapters
#
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET_MII=m
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
# CONFIG_USB_NET_DM9601 is not set
CONFIG_USB_NET_GL620A=m
CONFIG_USB_NET_NET1080=m
CONFIG_USB_NET_PLUSB=m
# CONFIG_USB_NET_MCS7830 is not set
CONFIG_USB_NET_RNDIS_HOST=m
CONFIG_USB_NET_CDC_SUBSET=m
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_BELKIN=y
CONFIG_USB_ARMLINUX=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_KC2190=y
CONFIG_USB_NET_ZAURUS=m
CONFIG_NET_PCMCIA=y
CONFIG_PCMCIA_3C589=m
CONFIG_PCMCIA_3C574=m
CONFIG_PCMCIA_FMVJ18X=m
CONFIG_PCMCIA_PCNET=m
CONFIG_PCMCIA_NMCLAN=m
CONFIG_PCMCIA_SMC91C92=m
CONFIG_PCMCIA_XIRC2PS=m
CONFIG_PCMCIA_AXNET=m
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
CONFIG_SHAPER=m
CONFIG_NETCONSOLE=m
CONFIG_NETCONSOLE_DYNAMIC=y
CONFIG_NETPOLL=y
CONFIG_NETPOLL_TRAP=y
CONFIG_NET_POLL_CONTROLLER=y
# CONFIG_ISDN is not set
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y
CONFIG_INPUT_FF_MEMLESS=m
CONFIG_INPUT_POLLDEV=m

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=m
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
CONFIG_KEYBOARD_SUNKBD=m
# CONFIG_KEYBOARD_LKKBD is not set
CONFIG_KEYBOARD_XTKBD=m
CONFIG_KEYBOARD_NEWTON=m
# CONFIG_KEYBOARD_STOWAWAY is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=m
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
CONFIG_MOUSE_PS2_LIFEBOOK=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
CONFIG_MOUSE_PS2_TOUCHKIT=y
CONFIG_MOUSE_SERIAL=m
# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=y
CONFIG_INPUT_ATLAS_BTNS=m
# CONFIG_INPUT_ATI_REMOTE is not set
# CONFIG_INPUT_ATI_REMOTE2 is not set
# CONFIG_INPUT_KEYSPAN_REMOTE is not set
# CONFIG_INPUT_POWERMATE is not set
# CONFIG_INPUT_YEALINK is not set
CONFIG_INPUT_UINPUT=m

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=m
CONFIG_SERIO_CT82C710=m
CONFIG_SERIO_PCIPS2=m
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=m
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_UNICODE=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_NOZOMI is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_FIX_EARLYCON_MEM=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_PNP=y
CONFIG_SERIAL_8250_CS=m
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=64
CONFIG_IPMI_HANDLER=m
CONFIG_IPMI_PANIC_EVENT=y
# CONFIG_IPMI_PANIC_STRING is not set
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_SI=m
CONFIG_IPMI_WATCHDOG=m
CONFIG_IPMI_POWEROFF=m
CONFIG_HW_RANDOM=y
# CONFIG_HW_RANDOM_INTEL is not set
CONFIG_HW_RANDOM_AMD=y
CONFIG_NVRAM=y
CONFIG_RTC=y
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
CONFIG_AGP=y
CONFIG_AGP_AMD64=y
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_VIA is not set
CONFIG_DRM=m
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_R128 is not set
CONFIG_DRM_RADEON=m
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set
# CONFIG_DRM_VIA is not set
# CONFIG_DRM_SAVAGE is not set

#
# PCMCIA character devices
#
CONFIG_SYNCLINK_CS=m
CONFIG_CARDMAN_4000=m
CONFIG_CARDMAN_4040=m
# CONFIG_IPWIRELESS_CS is not set
# CONFIG_MWAVE is not set
# CONFIG_PC8736x_GPIO is not set
CONFIG_RAW_DRIVER=m
CONFIG_MAX_RAW_DEVS=4096
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
CONFIG_HANGCHECK_TIMER=m
CONFIG_TCG_TPM=m
# CONFIG_TCG_TIS is not set
# CONFIG_TCG_NSC is not set
CONFIG_TCG_ATMEL=m
# CONFIG_TCG_INFINEON is not set
CONFIG_TELCLOCK=m
CONFIG_DEVPORT=y
CONFIG_I2C=m
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=m

#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_ALGOPCF=m
CONFIG_I2C_ALGOPCA=m

#
# I2C Hardware Bus support
#
CONFIG_I2C_ALI1535=m
CONFIG_I2C_ALI1563=m
CONFIG_I2C_ALI15X3=m
CONFIG_I2C_AMD756=m
CONFIG_I2C_AMD756_S4882=m
CONFIG_I2C_AMD8111=m
CONFIG_I2C_I801=m
CONFIG_I2C_I810=m
CONFIG_I2C_PIIX4=m
CONFIG_I2C_NFORCE2=m
# CONFIG_I2C_OCORES is not set
CONFIG_I2C_PARPORT_LIGHT=m
CONFIG_I2C_PROSAVAGE=m
CONFIG_I2C_SAVAGE4=m
CONFIG_I2C_SIMTEC=m
CONFIG_I2C_SIS5595=m
CONFIG_I2C_SIS630=m
CONFIG_I2C_SIS96X=m
# CONFIG_I2C_TAOS_EVM is not set
CONFIG_I2C_STUB=m
CONFIG_I2C_TINY_USB=m
CONFIG_I2C_VIA=m
CONFIG_I2C_VIAPRO=m
CONFIG_I2C_VOODOO3=m

#
# Miscellaneous I2C Chip support
#
CONFIG_SENSORS_DS1337=m
CONFIG_SENSORS_DS1374=m
# CONFIG_DS1682 is not set
CONFIG_SENSORS_EEPROM=m
CONFIG_SENSORS_PCF8574=m
CONFIG_SENSORS_PCA9539=m
CONFIG_SENSORS_PCF8591=m
CONFIG_SENSORS_MAX6875=m
CONFIG_SENSORS_TSL2550=m
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set

#
# SPI support
#
CONFIG_SPI=y
CONFIG_SPI_DEBUG=y
CONFIG_SPI_MASTER=y

#
# SPI Master Controller Drivers
#
CONFIG_SPI_BITBANG=m

#
# SPI Protocol Masters
#
CONFIG_SPI_AT25=m
# CONFIG_SPI_SPIDEV is not set
# CONFIG_SPI_TLE62X0 is not set
CONFIG_W1=m
CONFIG_W1_CON=y

#
# 1-wire Bus Masters
#
# CONFIG_W1_MASTER_MATROX is not set
# CONFIG_W1_MASTER_DS2490 is not set
# CONFIG_W1_MASTER_DS2482 is not set

#
# 1-wire Slaves
#
# CONFIG_W1_SLAVE_THERM is not set
# CONFIG_W1_SLAVE_SMEM is not set
# CONFIG_W1_SLAVE_DS2433 is not set
# CONFIG_W1_SLAVE_DS2760 is not set
CONFIG_POWER_SUPPLY=m
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_BATTERY_DS2760 is not set
CONFIG_HWMON=m
CONFIG_HWMON_VID=m
# CONFIG_SENSORS_ABITUGURU is not set
# CONFIG_SENSORS_ABITUGURU3 is not set
# CONFIG_SENSORS_AD7418 is not set
CONFIG_SENSORS_ADM1021=m
CONFIG_SENSORS_ADM1025=m
CONFIG_SENSORS_ADM1026=m
# CONFIG_SENSORS_ADM1029 is not set
CONFIG_SENSORS_ADM1031=m
CONFIG_SENSORS_ADM9240=m
CONFIG_SENSORS_ADT7470=m
CONFIG_SENSORS_K8TEMP=m
CONFIG_SENSORS_ASB100=m
CONFIG_SENSORS_ATXP1=m
CONFIG_SENSORS_DS1621=m
CONFIG_SENSORS_F71805F=m
CONFIG_SENSORS_F71882FG=m
CONFIG_SENSORS_F75375S=m
CONFIG_SENSORS_FSCHER=m
CONFIG_SENSORS_FSCPOS=m
CONFIG_SENSORS_GL518SM=m
CONFIG_SENSORS_GL520SM=m
# CONFIG_SENSORS_CORETEMP is not set
CONFIG_SENSORS_IT87=m
CONFIG_SENSORS_LM63=m
# CONFIG_SENSORS_LM70 is not set
CONFIG_SENSORS_LM75=m
CONFIG_SENSORS_LM77=m
CONFIG_SENSORS_LM78=m
CONFIG_SENSORS_LM80=m
CONFIG_SENSORS_LM83=m
CONFIG_SENSORS_LM85=m
CONFIG_SENSORS_LM87=m
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_LM92=m
CONFIG_SENSORS_LM93=m
CONFIG_SENSORS_MAX1619=m
# CONFIG_SENSORS_MAX6650 is not set
CONFIG_SENSORS_PC87360=m
# CONFIG_SENSORS_PC87427 is not set
CONFIG_SENSORS_SIS5595=m
CONFIG_SENSORS_DME1737=m
CONFIG_SENSORS_SMSC47M1=m
# CONFIG_SENSORS_SMSC47M192 is not set
CONFIG_SENSORS_SMSC47B397=m
# CONFIG_SENSORS_THMC50 is not set
CONFIG_SENSORS_VIA686A=m
# CONFIG_SENSORS_VT1211 is not set
CONFIG_SENSORS_VT8231=m
CONFIG_SENSORS_W83781D=m
# CONFIG_SENSORS_W83791D is not set
CONFIG_SENSORS_W83792D=m
CONFIG_SENSORS_W83793=m
CONFIG_SENSORS_W83L785TS=m
CONFIG_SENSORS_W83627HF=m
CONFIG_SENSORS_W83627EHF=m
CONFIG_SENSORS_HDAPS=m
# CONFIG_SENSORS_APPLESMC is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_WATCHDOG is not set

#
# Sonics Silicon Backplane
#
CONFIG_SSB_POSSIBLE=y
CONFIG_SSB=m
CONFIG_SSB_PCIHOST_POSSIBLE=y
CONFIG_SSB_PCIHOST=y
CONFIG_SSB_PCMCIAHOST_POSSIBLE=y
# CONFIG_SSB_PCMCIAHOST is not set
CONFIG_SSB_DEBUG=y
CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
CONFIG_SSB_DRIVER_PCICORE=y

#
# Multifunction device drivers
#
# CONFIG_MFD_SM501 is not set

#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
# CONFIG_DAB is not set

#
# Graphics support
#
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=m
CONFIG_LCD_LTV350QV=m
CONFIG_BACKLIGHT_CLASS_DEVICE=m
CONFIG_BACKLIGHT_PROGEAR=m

#
# Display device support
#
CONFIG_DISPLAY_SUPPORT=m

#
# Display hardware drivers
#
# CONFIG_VGASTATE is not set
CONFIG_VIDEO_OUTPUT_CONTROL=m
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
# CONFIG_FB_DDC is not set
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
# CONFIG_FB_SYS_FOPS is not set
CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y

#
# Frame buffer hardware drivers
#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_UVESA is not set
CONFIG_FB_VESA=y
# CONFIG_FB_EFI is not set
# CONFIG_FB_HECUBA is not set
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_NVIDIA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_LE80578 is not set
# CONFIG_FB_INTEL is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_VT8623 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_VIRTUAL is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_VGACON_SOFT_SCROLLBACK=y
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=64
CONFIG_VIDEO_SELECT=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
CONFIG_FONTS=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
# CONFIG_FONT_6x11 is not set
# CONFIG_FONT_7x14 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set
# CONFIG_FONT_MINI_4x6 is not set
# CONFIG_FONT_SUN8x16 is not set
# CONFIG_FONT_SUN12x22 is not set
# CONFIG_FONT_10x18 is not set
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_LOGO_LINUX_CLUT224=y

#
# Sound
#
CONFIG_SOUND=m

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
CONFIG_SND_DYNAMIC_MINORS=y
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
CONFIG_SND_VERBOSE_PRINTK=y
CONFIG_SND_DEBUG=y
# CONFIG_SND_DEBUG_DETECT is not set
# CONFIG_SND_PCM_XRUN_DEBUG is not set

#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
CONFIG_SND_AC97_CODEC=m
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
CONFIG_SND_MTPAV=m
CONFIG_SND_SERIAL_U16550=m
CONFIG_SND_MPU401=m

#
# PCI devices
#
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_ALI5451 is not set
CONFIG_SND_ATIIXP=m
CONFIG_SND_ATIIXP_MODEM=m
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS5530 is not set
# CONFIG_SND_DARLA20 is not set
# CONFIG_SND_GINA20 is not set
# CONFIG_SND_LAYLA20 is not set
# CONFIG_SND_DARLA24 is not set
# CONFIG_SND_GINA24 is not set
# CONFIG_SND_LAYLA24 is not set
# CONFIG_SND_MONA is not set
# CONFIG_SND_MIA is not set
# CONFIG_SND_ECHO3G is not set
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_FM801 is not set
CONFIG_SND_HDA_INTEL=m
CONFIG_SND_HDA_HWDEP=y
CONFIG_SND_HDA_CODEC_REALTEK=y
CONFIG_SND_HDA_CODEC_ANALOG=y
CONFIG_SND_HDA_CODEC_SIGMATEL=y
CONFIG_SND_HDA_CODEC_VIA=y
CONFIG_SND_HDA_CODEC_ATIHDMI=y
CONFIG_SND_HDA_CODEC_CONEXANT=y
CONFIG_SND_HDA_CODEC_CMEDIA=y
CONFIG_SND_HDA_CODEC_SI3054=y
CONFIG_SND_HDA_GENERIC=y
CONFIG_SND_HDA_POWER_SAVE=y
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
CONFIG_SND_INTEL8X0=m
CONFIG_SND_INTEL8X0M=m
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RIPTIDE is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
CONFIG_SND_AC97_POWER_SAVE=y

#
# SPI devices
#

#
# USB devices
#
CONFIG_SND_USB_AUDIO=m
CONFIG_SND_USB_USX2Y=m
# CONFIG_SND_USB_CAIAQ is not set

#
# PCMCIA devices
#
# CONFIG_SND_VXPOCKET is not set
# CONFIG_SND_PDAUDIOCF is not set

#
# System on Chip audio support
#
# CONFIG_SND_SOC is not set

#
# SoC Audio support for SuperH
#

#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
CONFIG_AC97_BUS=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set

#
# USB Input Devices
#
CONFIG_USB_HID=m
# CONFIG_USB_HIDINPUT_POWERBOOK is not set
CONFIG_HID_FF=y
CONFIG_HID_PID=y
CONFIG_LOGITECH_FF=y
# CONFIG_PANTHERLORD_FF is not set
CONFIG_THRUSTMASTER_FF=y
# CONFIG_ZEROPLUS_FF is not set
CONFIG_USB_HIDDEV=y

#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=m
CONFIG_USB_DEBUG=y

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
CONFIG_USB_SUSPEND=y
# CONFIG_USB_PERSIST is not set
# CONFIG_USB_OTG is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
CONFIG_USB_ISP116X_HCD=m
CONFIG_USB_OHCI_HCD=m
CONFIG_USB_OHCI_HCD_SSB=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
CONFIG_USB_SL811_HCD=m
CONFIG_USB_SL811_CS=m
CONFIG_USB_R8A66597_HCD=m

#
# USB Device Class drivers
#
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m

#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#

#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
CONFIG_USB_STORAGE_ALAUDA=y
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set

#
# USB Imaging devices
#
CONFIG_USB_MDC800=m
CONFIG_USB_MICROTEK=m
CONFIG_USB_MON=y

#
# USB port drivers
#

#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
# CONFIG_USB_SERIAL_AIRCABLE is not set
CONFIG_USB_SERIAL_AIRPRIME=m
# CONFIG_USB_SERIAL_ARK3116 is not set
CONFIG_USB_SERIAL_BELKIN=m
CONFIG_USB_SERIAL_CH341=m
CONFIG_USB_SERIAL_WHITEHEAT=m
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
CONFIG_USB_SERIAL_CP2101=m
CONFIG_USB_SERIAL_CYPRESS_M8=m
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_FUNSOFT=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
CONFIG_USB_SERIAL_IR=m
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
CONFIG_USB_SERIAL_GARMIN=m
CONFIG_USB_SERIAL_IPW=m
CONFIG_USB_SERIAL_KEYSPAN_PDA=m
CONFIG_USB_SERIAL_KEYSPAN=m
CONFIG_USB_SERIAL_KEYSPAN_MPR=y
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
CONFIG_USB_SERIAL_KLSI=m
CONFIG_USB_SERIAL_KOBIL_SCT=m
CONFIG_USB_SERIAL_MCT_U232=m
# CONFIG_USB_SERIAL_MOS7720 is not set
CONFIG_USB_SERIAL_MOS7840=m
CONFIG_USB_SERIAL_NAVMAN=m
CONFIG_USB_SERIAL_PL2303=m
CONFIG_USB_SERIAL_OTI6858=m
CONFIG_USB_SERIAL_HP4X=m
CONFIG_USB_SERIAL_SAFE=m
CONFIG_USB_SERIAL_SAFE_PADDED=y
# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set
CONFIG_USB_SERIAL_TI=m
CONFIG_USB_SERIAL_CYBERJACK=m
CONFIG_USB_SERIAL_XIRCOM=m
CONFIG_USB_SERIAL_OPTION=m
CONFIG_USB_SERIAL_OMNINET=m
CONFIG_USB_SERIAL_DEBUG=m
CONFIG_USB_EZUSB=y

#
# USB Miscellaneous drivers
#
CONFIG_USB_EMI62=m
CONFIG_USB_EMI26=m
# CONFIG_USB_ADUTUX is not set
CONFIG_USB_AUERSWALD=m
CONFIG_USB_RIO500=m
CONFIG_USB_LEGOTOWER=m
CONFIG_USB_LCD=m
# CONFIG_USB_BERRY_CHARGE is not set
CONFIG_USB_LED=m
# CONFIG_USB_CYPRESS_CY7C63 is not set
CONFIG_USB_CYTHERM=m
# CONFIG_USB_PHIDGET is not set
CONFIG_USB_IDMOUSE=m
# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
CONFIG_USB_SISUSBVGA=m
CONFIG_USB_SISUSBVGA_CON=y
CONFIG_USB_LD=m
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
# CONFIG_USB_GOTEMP is not set

#
# USB DSL modem support
#

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
CONFIG_MMC=m
# CONFIG_MMC_DEBUG is not set
# CONFIG_MMC_UNSAFE_RESUME is not set
# CONFIG_MMC_PASSWORDS is not set

#
# MMC/SD Card Drivers
#
CONFIG_MMC_BLOCK=m
CONFIG_MMC_BLOCK_BOUNCE=y
# CONFIG_SDIO_UART is not set

#
# MMC/SD Host Controller Drivers
#
CONFIG_MMC_SDHCI=m
CONFIG_MMC_WBSD=m
CONFIG_MMC_TIFM_SD=m
# CONFIG_MMC_SPI is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=m

#
# LED drivers
#

#
# LED Triggers
#
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=m
CONFIG_LEDS_TRIGGER_IDE_DISK=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=m
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
CONFIG_RTC_LIB=m
CONFIG_RTC_CLASS=m

#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
# CONFIG_RTC_DRV_TEST is not set

#
# I2C RTC drivers
#
# CONFIG_RTC_DRV_DS1307 is not set
# CONFIG_RTC_DRV_DS1672 is not set
# CONFIG_RTC_DRV_MAX6900 is not set
# CONFIG_RTC_DRV_RS5C372 is not set
# CONFIG_RTC_DRV_ISL1208 is not set
# CONFIG_RTC_DRV_X1205 is not set
# CONFIG_RTC_DRV_PCF8563 is not set
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_M41T80 is not set

#
# SPI RTC drivers
#
# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_MAX6902 is not set

#
# Platform RTC drivers
#
CONFIG_RTC_DRV_CMOS=m
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T59 is not set
# CONFIG_RTC_DRV_V3020 is not set

#
# on-CPU RTC drivers
#
# CONFIG_DMADEVICES is not set
# CONFIG_VIRTUALIZATION is not set

#
# Userspace I/O
#
# CONFIG_UIO is not set

#
# Firmware Drivers
#
CONFIG_EDD=m
CONFIG_DELL_RBU=m
CONFIG_DCDBAS=m
CONFIG_DMIID=y

#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=m
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=m
CONFIG_JBD_DEBUG=y
CONFIG_FS_MBCACHE=y
# CONFIG_REISER4_FS is not set
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
CONFIG_REISERFS_FS_SECURITY=y
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
CONFIG_QUOTA=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
CONFIG_PRINT_QUOTA_WARNING=y
CONFIG_QFMT_V1=m
CONFIG_QFMT_V2=m
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
CONFIG_FUSE_FS=m
CONFIG_GENERIC_ACL=y

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=852
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-2"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
CONFIG_NTFS_RW=y

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
CONFIG_CONFIGFS_FS=m

#
# Layered filesystems
#
# CONFIG_ECRYPT_FS is not set
# CONFIG_UNION_FS is not set

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_JFFS2_FS=m
CONFIG_JFFS2_FS_DEBUG=0
CONFIG_JFFS2_FS_WRITEBUFFER=y
# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
CONFIG_JFFS2_SUMMARY=y
# CONFIG_JFFS2_FS_XATTR is not set
CONFIG_JFFS2_COMPRESSION_OPTIONS=y
CONFIG_JFFS2_ZLIB=y
CONFIG_JFFS2_LZO=y
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
# CONFIG_JFFS2_CMODE_NONE is not set
CONFIG_JFFS2_CMODE_PRIORITY=y
# CONFIG_JFFS2_CMODE_SIZE is not set
# CONFIG_JFFS2_CMODE_FAVOURLZO is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set

#
# Network File Systems
#
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=m
CONFIG_NFSD_V2_ACL=y
CONFIG_NFSD_V3=y
CONFIG_NFSD_V3_ACL=y
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_ACL_SUPPORT=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=m
CONFIG_RPCSEC_GSS_SPKM3=m
# CONFIG_SMB_FS is not set
CONFIG_CIFS=m
CONFIG_CIFS_STATS=y
CONFIG_CIFS_STATS2=y
CONFIG_CIFS_WEAK_PW_HASH=y
CONFIG_CIFS_XATTR=y
CONFIG_CIFS_POSIX=y
# CONFIG_CIFS_DEBUG2 is not set
CONFIG_CIFS_EXPERIMENTAL=y
CONFIG_CIFS_UPCALL=y
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y

#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf8"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m

#
# Distributed Lock Manager
#
# CONFIG_DLM is not set

#
# Instrumentation Support
#
CONFIG_PROFILING=y
CONFIG_OPROFILE=m
CONFIG_KPROBES=y

#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_UNUSED_SYMBOLS=y
# CONFIG_PAGE_OWNER is not set
CONFIG_DEBUG_FS=y
CONFIG_HEADERS_CHECK=y
CONFIG_DEBUG_KERNEL=y
CONFIG_DEBUG_SHIRQ=y
CONFIG_DETECT_SOFTLOCKUP=y
CONFIG_SCHED_DEBUG=y
CONFIG_SCHEDSTATS=y
CONFIG_TIMER_STATS=y
CONFIG_DEBUG_SLAB=y
CONFIG_DEBUG_SLAB_LEAK=y
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_VM=y
# CONFIG_DEBUG_LIST is not set
CONFIG_FRAME_POINTER=y
# CONFIG_UNWIND_INFO is not set
# CONFIG_PROFILE_LIKELY is not set
CONFIG_FORCED_INLINING=y
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_DEBUG_SYNCHRO_TEST is not set
CONFIG_RCU_TORTURE_TEST=m
# CONFIG_LKDTM is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_WANT_EXTRA_DEBUG_INFORMATION is not set
# CONFIG_KGDB is not set
# CONFIG_KGDB_ATTACH_WAIT is not set
CONFIG_DEBUG_RODATA=y
# CONFIG_IOMMU_DEBUG is not set
CONFIG_DEBUG_STACKOVERFLOW=y
# CONFIG_DEBUG_STACK_USAGE is not set

#
# Security options
#
CONFIG_KEYS=y
CONFIG_KEYS_DEBUG_PROC_KEYS=y
CONFIG_SECURITY=y
CONFIG_SECURITY_NETWORK=y
# CONFIG_SECURITY_NETWORK_XFRM is not set
CONFIG_SECURITY_CAPABILITIES=y
CONFIG_SECURITY_FILE_CAPABILITIES=y
# CONFIG_SECURITY_SELINUX is not set
CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ABLKCIPHER=m
CONFIG_CRYPTO_AEAD=m
CONFIG_CRYPTO_BLKCIPHER=m
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_GF128MUL=m
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_FCRYPT=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m
CONFIG_CRYPTO_TWOFISH_X86_64=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_AES_X86_64=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_SEED=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_AUTHENC=m
# CONFIG_CRYPTO_HW is not set

#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
CONFIG_CRC7=m
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m
CONFIG_LZO_COMPRESS=m
CONFIG_LZO_DECOMPRESS=m
CONFIG_REED_SOLOMON=m
CONFIG_REED_SOLOMON_DEC16=y
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Thomas Gleixner]

On Sun, 2007-09-23 at 22:08 +0200, Rafael J. Wysocki wrote:
> > > Since the boot fails very early, before any messages reach the (VGA) console,
> > > I have no idea what to do next, except for digging in the code.
> > 
> > Ok, lets track it down. Is there any difference when you add:
> > 
> > nohz=off
> > highres=off
> > noapictimer
> > 
> > or any combinations of the above to the kernel command line ?
> 
> First, for now, I build all kernels with NO_HZ and HIGH_RES_TIMERS unset
> (.config for 2.6.23-rc6-mm1 is attached).
> 
> Second, noacpitimer added to the command line makes all of the kernels, up to
> and including 2.6.23-rc6-mm1, boot (this seems to be 100% reproducible).

That's valuable information. Can you please provide a boot log of one of
those with an additional "apic=verbose" on the command line ?

Thanks,

	tglx

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

[-- Attachment #1: Type: text/plain, Size: 1248 bytes --]

On Sunday, 23 September 2007 21:59, Thomas Gleixner wrote:
> On Sun, 2007-09-23 at 22:08 +0200, Rafael J. Wysocki wrote:
> > > > Since the boot fails very early, before any messages reach the (VGA) console,
> > > > I have no idea what to do next, except for digging in the code.
> > > 
> > > Ok, lets track it down. Is there any difference when you add:
> > > 
> > > nohz=off
> > > highres=off
> > > noapictimer
> > > 
> > > or any combinations of the above to the kernel command line ?
> > 
> > First, for now, I build all kernels with NO_HZ and HIGH_RES_TIMERS unset
> > (.config for 2.6.23-rc6-mm1 is attached).
> > 
> > Second, noacpitimer added to the command line makes all of the kernels, up to
> > and including 2.6.23-rc6-mm1, boot (this seems to be 100% reproducible).
> 
> That's valuable information. Can you please provide a boot log of one of
> those with an additional "apic=verbose" on the command line ?

Attached is the dmesg output from the 2.6.23-rc6 kernel with the patchset:

http://tglx.de/projects/hrtimers/2.6.23-rc4/patch-2.6.23-rc4-hrt1.patches.tar.bz2

applied.  I also have the 2.6.23-rc6-mm1 dmesg output ready, but there's some
-mm-specific noise in it.  Please let me know if you want it, though.

Greetings,
Rafael

[-- Attachment #2: 2.6.23-rc6-hrt.log --]
[-- Type: text/x-log, Size: 38785 bytes --]

Linux version 2.6.23-rc6-hrt (rafael@albercik) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #1 SMP Sat Sep 22 22:38:18 CEST 2007
Command line: root=/dev/sda3 vga=792 resume=/dev/sda1 noacpitimer apic=verbose 2
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000077fd0000 (usable)
 BIOS-e820: 0000000077fd0000 - 0000000077fe5600 (reserved)
 BIOS-e820: 0000000077fe5600 - 0000000077ff8000 (ACPI NVS)
 BIOS-e820: 0000000077ff8000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved)
 BIOS-e820: 00000000ffbc0000 - 00000000ffcc0000 (reserved)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 491472) 1 entries of 256 used
end_pfn_map = 1048576
DMI 2.4 present.
ACPI: RSDP 000F7D30, 0024 (r2 HP    )
ACPI: XSDT 77FE57B4, 0054 (r1 HP     0944      6070620 HP          1)
ACPI: FACP 77FE5684, 00F4 (r4 HP     0944            3 HP          1)
ACPI: DSDT 77FE58DC, EE7A (r1 HP        SB400    10000 MSFT  100000E)
ACPI: FACS 77FF7E80, 0040
ACPI: APIC 77FE5808, 0062 (r1 HP     0944            1 HP          1)
ACPI: MCFG 77FE586C, 003C (r1 HP     0944            1 HP          1)
ACPI: TCPA 77FE58A8, 0032 (r2 HP     0944            1 HP          1)
ACPI: SSDT 77FF4756, 0059 (r1 HP       HPQNLP        1 MSFT  100000E)
ACPI: SSDT 77FF47AF, 0206 (r1 HP     PSSTBLID        1 HP          1)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 491472) 1 entries of 256 used
No mptable found.
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0:        0 ->      159
    0:      256 ->   491472
On node 0 totalpages: 491375
  DMA zone: 56 pages used for memmap
  DMA zone: 1446 pages reserved
  DMA zone: 2497 pages, LIFO batch:0
  DMA32 zone: 6663 pages used for memmap
  DMA32 zone: 480713 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
mapped APIC to ffffffffff5fb000 (        fee00000)
mapped IOAPIC to ffffffffff5fa000 (00000000fec00000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 47576 bytes of per cpu data
Built 1 zonelists in Zone order.  Total pages: 483210
Kernel command line: root=/dev/sda3 vga=792 resume=/dev/sda1 noacpitimer apic=verbose 2
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
TSC calibrated against PM_TIMER
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 1995.000 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ 30c000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 1924056k/1965888k available (2203k kernel code, 41160k reserved, 1441k data, 248k init)
Calibrating delay using timer specific routine.. 3994.09 BogoMIPS (lpj=7988184)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Parsing all Control Methods:
Table [DSDT](id 0001) - 1153 Objects with 113 Devices 337 Methods 33 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 2 Objects with 0 Devices 2 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0003) - 8 Objects with 0 Devices 0 Methods 0 Regions
 tbxface-0598 [00] tb_load_namespace     : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable                : Transition to ACPI mode successful
enabled ExtINT on CPU#0
ENABLING IO-APIC IRQs
init IO_APIC IRQs
 IO-APIC (apicid-pin) 2-0<7>IOAPIC[0]: Set routing entry (2-1 -> 0x31 -> IRQ 1 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-2 -> 0x30 -> IRQ 0 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-3 -> 0x33 -> IRQ 3 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-4 -> 0x34 -> IRQ 4 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-5 -> 0x35 -> IRQ 5 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-6 -> 0x36 -> IRQ 6 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-7 -> 0x37 -> IRQ 7 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-8 -> 0x38 -> IRQ 8 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-9 -> 0x39 -> IRQ 9 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-10 -> 0x3a -> IRQ 10 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-11 -> 0x3b -> IRQ 11 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-12 -> 0x3c -> IRQ 12 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-13 -> 0x3d -> IRQ 13 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-14 -> 0x3e -> IRQ 14 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-15 -> 0x3f -> IRQ 15 Mode:0 Active:0)
, 2-16, 2-17, 2-18, 2-19, 2-20<7>IOAPIC[0]: Set routing entry (2-21 -> 0x49 -> IRQ 21 Mode:1 Active:1)
, 2-22, 2-23 not connected.
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...  failed.
...trying to set up timer as Virtual Wire IRQ... works.
Using local APIC timer interrupts.
APIC timer calibration result 12468749
Detected 12.468 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
masked ExtINT on CPU#1
Calibrating delay using timer specific routine.. 3989.98 BogoMIPS (lpj=7979977)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Turion(tm) 64 X2 Mobile Technology TL-60 stepping 02
Brought up 2 CPUs
Time: 20:43:44  Date: 08/23/107
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: No mmconfig possible on device 00:18
evgpeblk-0956 [00] ev_create_gpe_block   : GPE 00 to 1F [_GPE] 4 regs on int 0x15
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 3 Wake, Enabled 11 Runtime GPEs in this block
ACPI: EC: Look up EC in DSDT
ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
Completing Region/Field/Buffer/Package initialization:................................................................................................................................................................
Initialized 29/33 Regions 0/0 Fields 63/64 Buffers 68/78 Packages (1172 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:.......
Executed 7 _INI methods requiring 2 _STA executions (examined 120 objects)
ACPI: Interpreter enabled
ACPI: (supports S0 S3)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [C074] (0000:00)
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.C074._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C074.C075._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C074.C0DF._PRT]
ACPI: PCI Interrupt Link [C125] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C126] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C127] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C128] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C129] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C12A] (IRQs 9) *0, disabled.
ACPI: PCI Interrupt Link [C12B] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C12C] (IRQs *10 11)
ACPI: Power Resource [C223] (off)
ACPI: Power Resource [C1FE] (off)
ACPI: Power Resource [C217] (on)
ACPI: Power Resource [C34B] (off)
ACPI: Power Resource [C34C] (off)
ACPI: Power Resource [C34D] (off)
ACPI: Power Resource [C34E] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
IOAPIC[0]: Set routing entry (2-13 -> 0x3d -> IRQ 13 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-8 -> 0x38 -> IRQ 8 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-1 -> 0x31 -> IRQ 1 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-12 -> 0x3c -> IRQ 12 Mode:0 Active:0)
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 00000000
.......    : physical APIC id: 00
.... register #01: 00178021
.......     : max redirection entries: 0017
.......     : PRQ implemented: 1
.......     : IO APIC version: 0021
.... register #02: 00000000
.......     : arbitration: 00
.... IRQ redirection table:
 NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:   
 00 000 1    0    0   0   0    0    0    00
 01 003 0    0    0   0   0    1    1    31
 02 003 1    0    0   0   0    0    0    30
 03 003 0    0    0   0   0    1    1    33
 04 003 0    0    0   0   0    1    1    34
 05 003 0    0    0   0   0    1    1    35
 06 003 0    0    0   0   0    1    1    36
 07 003 0    0    0   0   0    1    1    37
 08 003 0    0    0   0   0    1    1    38
 09 003 1    0    0   0   0    1    1    39
 0a 003 0    0    0   0   0    1    1    3A
 0b 003 0    0    0   0   0    1    1    3B
 0c 003 0    0    0   0   0    1    1    3C
 0d 003 0    0    0   0   0    1    1    3D
 0e 003 0    0    0   0   0    1    1    3E
 0f 003 0    0    0   0   0    1    1    3F
 10 000 1    0    0   0   0    0    0    00
 11 000 1    0    0   0   0    0    0    00
 12 000 1    0    0   0   0    0    0    00
 13 000 1    0    0   0   0    0    0    00
 14 000 1    0    0   0   0    0    0    00
 15 003 0    1    0   1   0    1    1    49
 16 000 1    0    0   0   0    0    0    00
 17 000 1    0    0   0   0    0    0    00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ21 -> 0:21
.................................... done.
PCI: Cannot allocate resource region 0 of device 0000:00:14.2
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
ACPI: RTC can wake from S4
pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:00: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:00: iomem range 0x100000-0x77ffffff could not be reserved
pnp: 00:0a: ioport range 0x40b-0x40b has been reserved
pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0a: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:0a: iomem range 0xffb00000-0xffbfffff could not be reserved
pnp: 00:0a: iomem range 0xfff00000-0xffffffff could not be reserved
pnp: 00:0b: ioport range 0x8000-0x802f has been reserved
pnp: 00:0b: ioport range 0x8100-0x811f has been reserved
pnp: 00:0b: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:0c: iomem range 0xcf000-0xcffff has been reserved
pnp: 00:0c: iomem range 0x78000000-0x7fffffff could not be reserved
pnp: 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: 6000-6fff
  MEM window: d4300000-d43fffff
  PREFETCH window: c0000000-c7ffffff
PCI: Bridge: 0000:00:04.0
  IO window: 4000-5fff
  MEM window: d0000000-d3ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:05.0
  IO window: 2000-3fff
  MEM window: cc000000-cfffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
  IO window: disabled.
  MEM window: c8000000-c80fffff
  PREFETCH window: disabled.
PCI: Bus 3, cardbus bridge: 0000:02:04.0
  IO window: 00001000-000010ff
  IO window: 00001400-000014ff
  PREFETCH window: 88000000-8bffffff
  MEM window: 90000000-93ffffff
PCI: Bridge: 0000:00:14.4
  IO window: 1000-1fff
  MEM window: d4000000-d42fffff
  PREFETCH window: 88000000-8bffffff
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:05.0 to 64
PCI: Setting latency timer of device 0000:00:06.0 to 64
IOAPIC[0]: Set routing entry (2-20 -> 0x51 -> IRQ 20 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 20 (level, low) -> IRQ 20
NET: Registered protocol family 2
Time: acpi_pm clocksource has been installed.
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 5221k freed
audit: initializing netlink socket (disabled)
audit(1190580224.960:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: MSI quirk detected. MSI deactivated.
Boot video device is 0000:01:05.0
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie01]
Allocate Port Service[0000:00:04.0:pcie03]
PCI: Setting latency timer of device 0000:00:05.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:05.0:pcie00]
Allocate Port Service[0000:00:05.0:pcie01]
Allocate Port Service[0000:00:05.0:pcie03]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
Allocate Port Service[0000:00:06.0:pcie01]
Allocate Port Service[0000:00:06.0:pcie03]
AER service couldn't init device 0000:00:04.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:05.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:06.0:pcie01 - no _OSC support
vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20010100000, using 4608k, total 16384k
vesafb: mode is 1024x768x24, linelength=3072, pages=6
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize
sata_sil 0000:00:12.0: version 2.3
IOAPIC[0]: Set routing entry (2-16 -> 0x59 -> IRQ 16 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 16 (level, low) -> IRQ 16
scsi0 : sata_sil
scsi1 : sata_sil
ata1: SATA max UDMA/100 cmd 0xffffc2000002a080 ctl 0xffffc2000002a08a bmdma 0xffffc2000002a000 irq 16
ata2: SATA max UDMA/100 cmd 0xffffc2000002a0c0 ctl 0xffffc2000002a0ca bmdma 0xffffc2000002a008 irq 16
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: FUJITSU MHV2080BH, 892C, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA48 
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHV2080B 892C PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 0:0:0:0: [sda] Attached SCSI disk
PNP: PS/2 Controller [PNP0303:C214,PNP0f13:C215] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
NET: Registered protocol family 1
swsusp: Resume From Partition /dev/sda1
PM: Checking swsusp image.
PM: Resume from disk failed.
  Magic number: 7:553:751
  hash matches device ttyS2
Freeing unused kernel memory: 248k freed
Write protecting the kernel read-only data: 1060k
sd 0:0:0:0: Attached scsi generic sg0 type 0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
ATIIXP: chipset revision 128
ATIIXP: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x7040-0x7047, BIOS settings: hda:DMA, hdb:pio
ATIIXP: simplex device: DMA disabled
ide1: ATIIXP Bus-Master DMA disabled (BIOS)
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GMA-4082N, ATAPI CD/DVD-ROM drive
hda: selected mode 0x22
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
swsusp: Marking nosave pages: 000000000009f000 - 0000000000100000
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
Attempting manual resume
swsusp: Resume From Partition 8:1
PM: Checking swsusp image.
PM: Resume from disk failed.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Floppy drive(s): fd0 is 1.44M
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
ieee80211_crypt: registered algorithm 'NULL'
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:02:04.2[A] -> GSI 20 (level, low) -> IRQ 20
ACPI: PCI Interrupt 0000:02:04.1[A] -> GSI 20 (level, low) -> IRQ 20
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20]  MMIO=[d4011000-d40117ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc_cmos: probe of 00:07 failed with error -16
tg3.c:v3.80 (August 2, 2007)
IOAPIC[0]: Set routing entry (2-23 -> 0x61 -> IRQ 23 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 23 (level, low) -> IRQ 23
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:17:08:2e:2e:f3
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:02:04.3 [104c:803c] (rev 0)
ACPI: PCI Interrupt 0000:02:04.3[A] -> GSI 20 (level, low) -> IRQ 20
mmc0: SDHCI at 0xd4019000 irq 20 PIO
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
Yenta: CardBus bridge found at 0000:02:04.0 [103c:30b0]
Yenta: Enabling burst memory read transactions
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x01a11002, devctl 0x64
floppy0: no floppy controllers found
bcm43xx driver
Yenta: ISA IRQ mask 0x0ef8, PCI irq 20
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023f9929613f0c]
pcmcia: parent PCI bridge I/O window: 0x1000 - 0x1fff
pcmcia: parent PCI bridge Memory window: 0xd4000000 - 0xd42fffff
pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x8bffffff
IOAPIC[0]: Set routing entry (2-18 -> 0x69 -> IRQ 18 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:30:00.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:30:00.0 to 64
bcm43xx: Chip ID 0x4311, rev 0x1
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0x11, vendor 0x4243
bcm43xx: Core 1: ID 0x812, rev 0xa, vendor 0x4243
bcm43xx: Core 2: ID 0x817, rev 0x3, vendor 0x4243
bcm43xx: Core 3: ID 0x820, rev 0x1, vendor 0x4243
bcm43xx: PHY connected
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
bcm43xx: Detected PHY: Analog: 4, Type 2, Revision 8
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 80 td 96
IOAPIC[0]: Set routing entry (2-19 -> 0x71 -> IRQ 19 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.0: OHCI Host Controller
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file 'devices'
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: created debug files
ohci_hcd 0000:00:13.0: irq 19, io mem 0xd4401000
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
ohci_hcd 0000:00:13.0: OHCI controller state
ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:13.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:13.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:13.0: intrenable 0x8000005a MIE RHSC UE RD WDH
ohci_hcd 0000:00:13.0: hcca frame #0005
ohci_hcd 0000:00:13.0: roothub.a 02000204 POTPGT=2 NPS NDP=4(4)
ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:13.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [3] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.23-rc6-hrt ohci_hcd
usb usb1: SerialNumber: 0000:00:13.0
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 4ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: trying to enable port power on non-switchable hub
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0000
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.1: OHCI Host Controller
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.1: created debug files
ohci_hcd 0000:00:13.1: irq 19, io mem 0xd4402000
ohci_hcd 0000:00:13.1: OHCI controller state
ohci_hcd 0000:00:13.1: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:13.1: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:13.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:13.1: intrstatus 0x00000004 SF
ohci_hcd 0000:00:13.1: intrenable 0x8000005a MIE RHSC UE RD WDH
ohci_hcd 0000:00:13.1: hcca frame #0005
ohci_hcd 0000:00:13.1: roothub.a 02000204 POTPGT=2 NPS NDP=4(4)
ohci_hcd 0000:00:13.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:13.1: roothub.status 00008000 DRWE
ohci_hcd 0000:00:13.1: roothub.portstatus [0] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:13.1: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:13.1: roothub.portstatus [2] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:13.1: roothub.portstatus [3] 0x00000100 PPS
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.23-rc6-hrt ohci_hcd
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
usb usb2: SerialNumber: 0000:00:13.1
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 4ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: trying to enable port power on non-switchable hub
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 1-2: new full speed USB device using ohci_hcd and address 2
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: EHCI Host Controller
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '003'
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:13.2: reset hcs_params 0x2408 dbg=0 cc=2 pcc=4 ordered !ppc ports=8
ehci_hcd 0000:00:13.2: reset hcc_params a012 thresh 1 uframes 256/512/1024
ehci_hcd 0000:00:13.2: MWI active
ehci_hcd 0000:00:13.2: irq 19, io mem 0xd4403000
ehci_hcd 0000:00:13.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:13.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00130100 PRSC PESC CSC PPS
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 000a
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010100 CSC PPS
hub 2-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: EHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.23-rc6-hrt ehci_hcd
usb usb3: SerialNumber: 0000:00:13.2
usb usb3: uevent
usb usb3: usb_probe_device
usb usb3: configuration #1 chosen from 1 choice
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: uevent
usb 3-0:1.0: uevent
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: Single TT
hub 3-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 3-0:1.0: power on to power good time: 20ms
hub 3-0:1.0: local power source is good
hub 3-0:1.0: trying to enable port power on non-switchable hub
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
hub 2-0:1.0: port 3, status 0100, change 0001, 12 Mb/s
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0004
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00030100 PESC CSC PPS
hub 1-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
hub 3-0:1.0: state 7 ports 8 chg 0000 evt 0000
ehci_hcd 0000:00:13.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 3-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 2 full speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 2 status 003801 POWER OWNER sig=j CONNECT
hub 3-0:1.0: port 2 not reset yet, waiting 50ms
ehci_hcd 0000:00:13.2: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
ehci_hcd 0000:00:13.2: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 3-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 3 full speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 3 status 003801 POWER OWNER sig=j CONNECT
hub 3-0:1.0: port 3 not reset yet, waiting 50ms
ehci_hcd 0000:00:13.2: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC
ehci_hcd 0000:00:13.2: GetStatus port 6 status 001403 POWER sig=k CSC CONNECT
hub 3-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
hub 3-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 6 low speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 6 status 003002 POWER OWNER sig=se0 CSC
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0002
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 2-1: new full speed USB device using ohci_hcd and address 2
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04793/0x300000
serio: Synaptics pass-through port at isa0060/serio4/input0
usb 2-1: ep0 maxpacket = 8
usb 2-1: default language 0x0409
usb 2-1: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-1: Product: Fingerprint Sensor
usb 2-1: uevent
usb 2-1: usb_probe_device
usb 2-1: configuration #1 chosen from 1 choice
input: SynPS/2 Synaptics TouchPad as /class/input/input2
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: uevent
usb 2-1:1.0: uevent
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00010301 CSC LSDA PPS CCS
hub 2-0:1.0: port 3, status 0301, change 0001, 1.5 Mb/s
hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS
usb 2-3: new low speed USB device using ohci_hcd and address 3
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS
usb 2-3: skipped 1 descriptor after interface
usb 2-3: skipped 1 descriptor after interface
usb 2-3: default language 0x0409
usb 2-3: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-3: Product: USB Receiver
usb 2-3: Manufacturer: Logitech
usb 2-3: uevent
usb 2-3: usb_probe_device
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: adding 2-3:1.0 (config #1, interface 0)
usb 2-3:1.0: uevent
usb 2-3:1.0: uevent
usb 2-3: adding 2-3:1.1 (config #1, interface 1)
usb 2-3:1.1: uevent
usb 2-3:1.1: uevent
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '003'
hub 3-0:1.0: state 7 ports 8 chg 0000 evt 0040
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0004
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 1-2: new full speed USB device using ohci_hcd and address 3
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
usb 1-2: skipped 1 descriptor after interface
usb 1-2: default language 0x0409
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2: Product: HP Integrated Module
usb 1-2: Manufacturer: Broadcom Corp
usb 1-2: uevent
usb 1-2: usb_probe_device
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2: adding 1-2:1.1 (config #1, interface 1)
usb 1-2:1.1: uevent
usb 1-2:1.1: uevent
usb 1-2: adding 1-2:1.2 (config #1, interface 2)
usb 1-2:1.2: uevent
usb 1-2:1.2: uevent
usb 1-2: adding 1-2:1.3 (config #1, interface 3)
usb 1-2:1.3: uevent
usb 1-2:1.3: uevent
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '003'
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0008
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0004
usbcore: registered new interface driver hiddev
usbhid 2-3:1.0: usb_probe_interface
usbhid 2-3:1.0: usb_probe_interface - got id
input: Logitech USB Receiver as /class/input/input3
input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-3
usbhid 2-3:1.1: usb_probe_interface
usbhid 2-3:1.1: usb_probe_interface - got id
input: Logitech USB Receiver as /class/input/input4
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/file.c: looking for a minor, starting at 96
input,hiddev96: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:13.1-3
usbcore: registered new interface driver usbhid
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: HCI USB driver ver 2.9
hci_usb 1-2:1.0: usb_probe_interface
hci_usb 1-2:1.0: usb_probe_interface - got id
usb_endpoint usbdev1.3_ep83: ep_device_release called for usbdev1.3_ep83
usb_endpoint usbdev1.3_ep03: ep_device_release called for usbdev1.3_ep03
hci_usb 1-2:1.2: usb_probe_interface
hci_usb 1-2:1.2: usb_probe_interface - got id
hci_usb 1-2:1.3: usb_probe_interface
hci_usb 1-2:1.3: usb_probe_interface - got id
usbcore: registered new interface driver hci_usb
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
usb 2-1: usb auto-suspend
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
ehci_hcd 0000:00:13.2: suspend root hub
loop: module loaded
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
Adding 1052216k swap on /dev/sda1.  Priority:-1 extents:1 across:1052216k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ACPI: AC Adapter [C1BD] (on-line)
ACPI: Battery Slot [C1BF] (battery present)
ACPI: Battery Slot [C1BE] (battery absent)
input: Power Button (FF) as /class/input/input5
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [C25A]
input: Lid Switch as /class/input/input7
ACPI: Lid Switch [C25B]
ACPI: Transitioning device [C34F] to D3
ACPI: Transitioning device [C34F] to D3
ACPI: Fan [C34F] (off)
ACPI: Transitioning device [C350] to D3
ACPI: Transitioning device [C350] to D3
ACPI: Fan [C350] (off)
ACPI: Transitioning device [C351] to D3
ACPI: Transitioning device [C351] to D3
ACPI: Fan [C351] (off)
ACPI: Transitioning device [C352] to D3
ACPI: Transitioning device [C352] to D3
ACPI: Fan [C352] (off)
ACPI: Processor [C000] (supports 8 throttling states)
ACPI: Processor [C001] (supports 8 throttling states)
ACPI: Thermal Zone [TZ1] (60 C)
ACPI: Thermal Zone [TZ2] (50 C)
ACPI: Thermal Zone [TZ3] (29 C)
powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-60 processors (2 cpu cores) (version 2.00.00)
powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x13
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x15
powernow-k8:    2 : fid 0x8 (1600 MHz), vid 0x17
powernow-k8:    3 : fid 0x0 (800 MHz), vid 0x1e
powernow-k8: ph2 null fid transition 0xc

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Thomas Gleixner]

On Sun, 2007-09-23 at 22:52 +0200, Rafael J. Wysocki wrote:
> > > Second, noacpitimer added to the command line makes all of the kernels, up to
> > > and including 2.6.23-rc6-mm1, boot (this seems to be 100% reproducible).
> > 
> > That's valuable information. Can you please provide a boot log of one of
> > those with an additional "apic=verbose" on the command line ?
> 
> Attached is the dmesg output from the 2.6.23-rc6 kernel with the patchset:
> 
> http://tglx.de/projects/hrtimers/2.6.23-rc4/patch-2.6.23-rc4-hrt1.patches.tar.bz2
> 
> applied.  I also have the 2.6.23-rc6-mm1 dmesg output ready, but there's some
> -mm-specific noise in it.  Please let me know if you want it, though.

Hmm:

> Command line: root=/dev/sda3 vga=792 resume=/dev/sda1 noacpitimer apic=verbose 2
--------------------------------------------------------^^^^^^^^^^^

noacpitimer is not a valid commandline option.

I asked for: 
>> > > noapictimer

So I really wonder, why noacpitimer on the kernel command line makes any
difference. I'm confused.

	tglx

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

[-- Attachment #1: Type: text/plain, Size: 1338 bytes --]

On Monday, 24 September 2007 10:07, Thomas Gleixner wrote:
> On Sun, 2007-09-23 at 22:52 +0200, Rafael J. Wysocki wrote:
> > > > Second, noacpitimer added to the command line makes all of the kernels, up to
> > > > and including 2.6.23-rc6-mm1, boot (this seems to be 100% reproducible).
> > > 
> > > That's valuable information. Can you please provide a boot log of one of
> > > those with an additional "apic=verbose" on the command line ?
> > 
> > Attached is the dmesg output from the 2.6.23-rc6 kernel with the patchset:
> > 
> > http://tglx.de/projects/hrtimers/2.6.23-rc4/patch-2.6.23-rc4-hrt1.patches.tar.bz2
> > 
> > applied.  I also have the 2.6.23-rc6-mm1 dmesg output ready, but there's some
> > -mm-specific noise in it.  Please let me know if you want it, though.
> 
> Hmm:
> 
> > Command line: root=/dev/sda3 vga=792 resume=/dev/sda1 noacpitimer apic=verbose 2
> --------------------------------------------------------^^^^^^^^^^^
> 
> noacpitimer is not a valid commandline option.
> 
> I asked for: 
> >> > > noapictimer

I'm blind, sorry.

> So I really wonder, why noacpitimer on the kernel command line makes any
> difference. I'm confused.

\metoo

Well, it was probably read as "noacpi". :-)

Fortunately, noapictimer helps as well, dmesg attached (I have the one
from 2.6.23-rc6-mm1 ready, too).

Greetings,
Rafael

[-- Attachment #2: 2.6.23-rc6-hrt.log --]
[-- Type: text/x-log, Size: 38967 bytes --]

Linux version 2.6.23-rc6-hrt (rafael@albercik) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #1 SMP Sat Sep 22 22:38:18 CEST 2007
Command line: root=/dev/sda3 vga=792 resume=/dev/sda1 noapictimer apic=verbose 2
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000077fd0000 (usable)
 BIOS-e820: 0000000077fd0000 - 0000000077fe5600 (reserved)
 BIOS-e820: 0000000077fe5600 - 0000000077ff8000 (ACPI NVS)
 BIOS-e820: 0000000077ff8000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved)
 BIOS-e820: 00000000ffbc0000 - 00000000ffcc0000 (reserved)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 491472) 1 entries of 256 used
end_pfn_map = 1048576
DMI 2.4 present.
ACPI: RSDP 000F7D30, 0024 (r2 HP    )
ACPI: XSDT 77FE57B4, 0054 (r1 HP     0944      6070620 HP          1)
ACPI: FACP 77FE5684, 00F4 (r4 HP     0944            3 HP          1)
ACPI: DSDT 77FE58DC, EE7A (r1 HP        SB400    10000 MSFT  100000E)
ACPI: FACS 77FF7E80, 0040
ACPI: APIC 77FE5808, 0062 (r1 HP     0944            1 HP          1)
ACPI: MCFG 77FE586C, 003C (r1 HP     0944            1 HP          1)
ACPI: TCPA 77FE58A8, 0032 (r2 HP     0944            1 HP          1)
ACPI: SSDT 77FF4756, 0059 (r1 HP       HPQNLP        1 MSFT  100000E)
ACPI: SSDT 77FF47AF, 0206 (r1 HP     PSSTBLID        1 HP          1)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 491472) 1 entries of 256 used
No mptable found.
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0:        0 ->      159
    0:      256 ->   491472
On node 0 totalpages: 491375
  DMA zone: 56 pages used for memmap
  DMA zone: 1446 pages reserved
  DMA zone: 2497 pages, LIFO batch:0
  DMA32 zone: 6663 pages used for memmap
  DMA32 zone: 480713 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
mapped APIC to ffffffffff5fb000 (        fee00000)
mapped IOAPIC to ffffffffff5fa000 (00000000fec00000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 47576 bytes of per cpu data
Built 1 zonelists in Zone order.  Total pages: 483210
Kernel command line: root=/dev/sda3 vga=792 resume=/dev/sda1 noapictimer apic=verbose 2
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
TSC calibrated against PM_TIMER
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 1995.005 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ 108000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 1924056k/1965888k available (2203k kernel code, 41160k reserved, 1441k data, 248k init)
Calibrating delay using timer specific routine.. 3994.16 BogoMIPS (lpj=7988323)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Parsing all Control Methods:
Table [DSDT](id 0001) - 1153 Objects with 113 Devices 337 Methods 33 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 2 Objects with 0 Devices 2 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0003) - 8 Objects with 0 Devices 0 Methods 0 Regions
 tbxface-0598 [00] tb_load_namespace     : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable                : Transition to ACPI mode successful
enabled ExtINT on CPU#0
ENABLING IO-APIC IRQs
init IO_APIC IRQs
 IO-APIC (apicid-pin) 2-0<7>IOAPIC[0]: Set routing entry (2-1 -> 0x31 -> IRQ 1 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-2 -> 0x30 -> IRQ 0 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-3 -> 0x33 -> IRQ 3 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-4 -> 0x34 -> IRQ 4 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-5 -> 0x35 -> IRQ 5 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-6 -> 0x36 -> IRQ 6 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-7 -> 0x37 -> IRQ 7 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-8 -> 0x38 -> IRQ 8 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-9 -> 0x39 -> IRQ 9 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-10 -> 0x3a -> IRQ 10 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-11 -> 0x3b -> IRQ 11 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-12 -> 0x3c -> IRQ 12 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-13 -> 0x3d -> IRQ 13 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-14 -> 0x3e -> IRQ 14 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-15 -> 0x3f -> IRQ 15 Mode:0 Active:0)
, 2-16, 2-17, 2-18, 2-19, 2-20<7>IOAPIC[0]: Set routing entry (2-21 -> 0x49 -> IRQ 21 Mode:1 Active:1)
, 2-22, 2-23 not connected.
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...  failed.
...trying to set up timer as Virtual Wire IRQ... works.
Disabling APIC timer
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
masked ExtINT on CPU#1
Calibrating delay using timer specific routine.. 3990.36 BogoMIPS (lpj=7980739)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Turion(tm) 64 X2 Mobile Technology TL-60 stepping 02
Brought up 2 CPUs
Time: 12:49:59  Date: 08/24/107
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: No mmconfig possible on device 00:18
evgpeblk-0956 [00] ev_create_gpe_block   : GPE 00 to 1F [_GPE] 4 regs on int 0x15
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 3 Wake, Enabled 11 Runtime GPEs in this block
ACPI: EC: Look up EC in DSDT
ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
Completing Region/Field/Buffer/Package initialization:................................................................................................................................................................
Initialized 29/33 Regions 0/0 Fields 63/64 Buffers 68/78 Packages (1172 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:.......
Executed 7 _INI methods requiring 2 _STA executions (examined 120 objects)
ACPI: Interpreter enabled
ACPI: (supports S0 S3)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [C074] (0000:00)
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.C074._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C074.C075._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C074.C0DF._PRT]
ACPI: PCI Interrupt Link [C125] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C126] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C127] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C128] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C129] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C12A] (IRQs 9) *0, disabled.
ACPI: PCI Interrupt Link [C12B] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C12C] (IRQs *10 11)
ACPI: Power Resource [C223] (off)
ACPI: Power Resource [C1FE] (off)
ACPI: Power Resource [C217] (on)
ACPI: Power Resource [C34B] (off)
ACPI: Power Resource [C34C] (off)
ACPI: Power Resource [C34D] (off)
ACPI: Power Resource [C34E] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
IOAPIC[0]: Set routing entry (2-13 -> 0x3d -> IRQ 13 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-8 -> 0x38 -> IRQ 8 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-1 -> 0x31 -> IRQ 1 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-12 -> 0x3c -> IRQ 12 Mode:0 Active:0)
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 00000000
.......    : physical APIC id: 00
.... register #01: 00178021
.......     : max redirection entries: 0017
.......     : PRQ implemented: 1
.......     : IO APIC version: 0021
.... register #02: 00000000
.......     : arbitration: 00
.... IRQ redirection table:
 NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:   
 00 000 1    0    0   0   0    0    0    00
 01 003 0    0    0   0   0    1    1    31
 02 003 1    0    0   0   0    0    0    30
 03 003 0    0    0   0   0    1    1    33
 04 003 0    0    0   0   0    1    1    34
 05 003 0    0    0   0   0    1    1    35
 06 003 0    0    0   0   0    1    1    36
 07 003 0    0    0   0   0    1    1    37
 08 003 0    0    0   0   0    1    1    38
 09 003 1    0    0   0   0    1    1    39
 0a 003 0    0    0   0   0    1    1    3A
 0b 003 0    0    0   0   0    1    1    3B
 0c 003 0    0    0   0   0    1    1    3C
 0d 003 0    0    0   0   0    1    1    3D
 0e 003 0    0    0   0   0    1    1    3E
 0f 003 0    0    0   0   0    1    1    3F
 10 000 1    0    0   0   0    0    0    00
 11 000 1    0    0   0   0    0    0    00
 12 000 1    0    0   0   0    0    0    00
 13 000 1    0    0   0   0    0    0    00
 14 000 1    0    0   0   0    0    0    00
 15 003 0    1    0   1   0    1    1    49
 16 000 1    0    0   0   0    0    0    00
 17 000 1    0    0   0   0    0    0    00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ21 -> 0:21
.................................... done.
PCI: Cannot allocate resource region 0 of device 0000:00:14.2
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
ACPI: RTC can wake from S4
pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:00: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:00: iomem range 0x100000-0x77ffffff could not be reserved
pnp: 00:0a: ioport range 0x40b-0x40b has been reserved
pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0a: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:0a: iomem range 0xffb00000-0xffbfffff could not be reserved
pnp: 00:0a: iomem range 0xfff00000-0xffffffff could not be reserved
pnp: 00:0b: ioport range 0x8000-0x802f has been reserved
pnp: 00:0b: ioport range 0x8100-0x811f has been reserved
pnp: 00:0b: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:0c: iomem range 0xcf000-0xcffff has been reserved
pnp: 00:0c: iomem range 0x78000000-0x7fffffff could not be reserved
pnp: 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: 6000-6fff
  MEM window: d4300000-d43fffff
  PREFETCH window: c0000000-c7ffffff
PCI: Bridge: 0000:00:04.0
  IO window: 4000-5fff
  MEM window: d0000000-d3ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:05.0
  IO window: 2000-3fff
  MEM window: cc000000-cfffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
  IO window: disabled.
  MEM window: c8000000-c80fffff
  PREFETCH window: disabled.
PCI: Bus 3, cardbus bridge: 0000:02:04.0
  IO window: 00001000-000010ff
  IO window: 00001400-000014ff
  PREFETCH window: 88000000-8bffffff
  MEM window: 90000000-93ffffff
PCI: Bridge: 0000:00:14.4
  IO window: 1000-1fff
  MEM window: d4000000-d42fffff
  PREFETCH window: 88000000-8bffffff
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:05.0 to 64
PCI: Setting latency timer of device 0000:00:06.0 to 64
IOAPIC[0]: Set routing entry (2-20 -> 0x51 -> IRQ 20 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 20 (level, low) -> IRQ 20
NET: Registered protocol family 2
Time: acpi_pm clocksource has been installed.
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 5221k freed
audit: initializing netlink socket (disabled)
audit(1190638199.044:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: MSI quirk detected. MSI deactivated.
Boot video device is 0000:01:05.0
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie01]
Allocate Port Service[0000:00:04.0:pcie03]
PCI: Setting latency timer of device 0000:00:05.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:05.0:pcie00]
Allocate Port Service[0000:00:05.0:pcie01]
Allocate Port Service[0000:00:05.0:pcie03]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
Allocate Port Service[0000:00:06.0:pcie01]
Allocate Port Service[0000:00:06.0:pcie03]
AER service couldn't init device 0000:00:04.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:05.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:06.0:pcie01 - no _OSC support
vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20010100000, using 4608k, total 16384k
vesafb: mode is 1024x768x24, linelength=3072, pages=6
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize
sata_sil 0000:00:12.0: version 2.3
IOAPIC[0]: Set routing entry (2-16 -> 0x59 -> IRQ 16 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 16 (level, low) -> IRQ 16
scsi0 : sata_sil
scsi1 : sata_sil
ata1: SATA max UDMA/100 cmd 0xffffc2000002a080 ctl 0xffffc2000002a08a bmdma 0xffffc2000002a000 irq 16
ata2: SATA max UDMA/100 cmd 0xffffc2000002a0c0 ctl 0xffffc2000002a0ca bmdma 0xffffc2000002a008 irq 16
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: FUJITSU MHV2080BH, 892C, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA48 
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHV2080B 892C PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 0:0:0:0: [sda] Attached SCSI disk
PNP: PS/2 Controller [PNP0303:C214,PNP0f13:C215] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
NET: Registered protocol family 1
swsusp: Resume From Partition /dev/sda1
PM: Checking swsusp image.
PM: Resume from disk failed.
  Magic number: 7:880:835
Freeing unused kernel memory: 248k freed
Write protecting the kernel read-only data: 1060k
sd 0:0:0:0: Attached scsi generic sg0 type 0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
ATIIXP: chipset revision 128
ATIIXP: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x7040-0x7047, BIOS settings: hda:DMA, hdb:pio
ATIIXP: simplex device: DMA disabled
ide1: ATIIXP Bus-Master DMA disabled (BIOS)
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GMA-4082N, ATAPI CD/DVD-ROM drive
hda: selected mode 0x22
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
swsusp: Marking nosave pages: 000000000009f000 - 0000000000100000
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
Attempting manual resume
swsusp: Resume From Partition 8:1
PM: Checking swsusp image.
PM: Resume from disk failed.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:02:04.3 [104c:803c] (rev 0)
ACPI: PCI Interrupt 0000:02:04.3[A] -> GSI 20 (level, low) -> IRQ 20
mmc0: SDHCI at 0xd4019000 irq 20 PIO
ieee80211_crypt: registered algorithm 'NULL'
Floppy drive(s): fd0 is 1.44M
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc_cmos: probe of 00:07 failed with error -16
tg3.c:v3.80 (August 2, 2007)
IOAPIC[0]: Set routing entry (2-23 -> 0x61 -> IRQ 23 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 23 (level, low) -> IRQ 23
eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:17:08:<6>piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
2e:2e:f3
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ACPI: PCI Interrupt 0000:02:04.2[A] -> GSI 20 (level, low) -> IRQ 20
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Yenta: CardBus bridge found at 0000:02:04.0 [103c:30b0]
Yenta: Enabling burst memory read transactions
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x01a11002, devctl 0x64
Yenta: ISA IRQ mask 0x0eb8, PCI irq 20
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
pcmcia: parent PCI bridge I/O window: 0x1000 - 0x1fff
pcmcia: parent PCI bridge Memory window: 0xd4000000 - 0xd42fffff
pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x8bffffff
ACPI: PCI Interrupt 0000:02:04.1[A] -> GSI 20 (level, low) -> IRQ 20
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20]  MMIO=[d4011000-d40117ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
bcm43xx driver
IOAPIC[0]: Set routing entry (2-18 -> 0x69 -> IRQ 18 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:30:00.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:30:00.0 to 64
bcm43xx: Chip ID 0x4311, rev 0x1
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0x11, vendor 0x4243
bcm43xx: Core 1: ID 0x812, rev 0xa, vendor 0x4243
bcm43xx: Core 2: ID 0x817, rev 0x3, vendor 0x4243
bcm43xx: Core 3: ID 0x820, rev 0x1, vendor 0x4243
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 80 td 96
bcm43xx: PHY connected
bcm43xx: Detected PHY: Analog: 4, Type 2, Revision 8
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
IOAPIC[0]: Set routing entry (2-19 -> 0x71 -> IRQ 19 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.0: OHCI Host Controller
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file 'devices'
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: created debug files
ohci_hcd 0000:00:13.0: irq 19, io mem 0xd4401000
ohci_hcd 0000:00:13.0: OHCI controller state
ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:13.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:13.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:13.0: intrenable 0x8000005a MIE RHSC UE RD WDH
ohci_hcd 0000:00:13.0: hcca frame #0005
ohci_hcd 0000:00:13.0: roothub.a 02000204 POTPGT=2 NPS NDP=4(4)
ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:13.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [3] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.23-rc6-hrt ohci_hcd
usb usb1: SerialNumber: 0000:00:13.0
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 4ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: trying to enable port power on non-switchable hub
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0000
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
ohci_hcd 0000:00:13.1: OHCI Host Controller
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.1: created debug files
ohci_hcd 0000:00:13.1: irq 19, io mem 0xd4402000
ohci_hcd 0000:00:13.1: OHCI controller state
ohci_hcd 0000:00:13.1: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:13.1: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:13.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:13.1: intrstatus 0x00000004 SF
ohci_hcd 0000:00:13.1: intrenable 0x8000005a MIE RHSC UE RD WDH
ohci_hcd 0000:00:13.1: hcca frame #0005
ohci_hcd 0000:00:13.1: roothub.a 02000204 POTPGT=2 NPS NDP=4(4)
ohci_hcd 0000:00:13.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:13.1: roothub.status 00008000 DRWE
ohci_hcd 0000:00:13.1: roothub.portstatus [0] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:13.1: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:13.1: roothub.portstatus [2] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:13.1: roothub.portstatus [3] 0x00000100 PPS
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.23-rc6-hrt ohci_hcd
usb usb2: SerialNumber: 0000:00:13.1
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 4ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: trying to enable port power on non-switchable hub
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: EHCI Host Controller
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '003'
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
ehci_hcd 0000:00:13.2: reset hcs_params 0x2408 dbg=0 cc=2 pcc=4 ordered !ppc ports=8
ehci_hcd 0000:00:13.2: reset hcc_params a012 thresh 1 uframes 256/512/1024
ehci_hcd 0000:00:13.2: MWI active
ehci_hcd 0000:00:13.2: irq 19, io mem 0xd4403000
ehci_hcd 0000:00:13.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:13.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb 1-2: new full speed USB device using ohci_hcd and address 2
ohci_hcd 0000:00:13.0: urb ffff81007705c9c8 path 2 ep0in 5ec20000 cc 5 --> status -62
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: EHCI Host Controller
ohci_hcd 0000:00:13.0: urb ffff81007705c9c8 path 2 ep0in 5ec20000 cc 5 --> status -62
ohci_hcd 0000:00:13.0: urb ffff81007705c9c8 path 2 ep0in 5ec20000 cc 5 --> status -62
usb usb3: Manufacturer: Linux 2.6.23-rc6-hrt ehci_hcd
usb usb3: SerialNumber: 0000:00:13.2
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00030100 PESC CSC PPS
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0004
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00030100 PESC CSC PPS
hub 1-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023f9929613f0c]
usb usb3: uevent
usb usb3: usb_probe_device
usb usb3: configuration #1 chosen from 1 choice
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: uevent
usb 3-0:1.0: uevent
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: Single TT
hub 3-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 3-0:1.0: power on to power good time: 20ms
hub 3-0:1.0: local power source is good
hub 3-0:1.0: trying to enable port power on non-switchable hub
floppy0: no floppy controllers found
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 000a
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010100 CSC PPS
hub 2-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
hub 2-0:1.0: port 3, status 0100, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0000
hub 3-0:1.0: state 7 ports 8 chg 0000 evt 0000
ehci_hcd 0000:00:13.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 3-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 2 full speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 2 status 003801 POWER OWNER sig=j CONNECT
hub 3-0:1.0: port 2 not reset yet, waiting 50ms
ohci_hcd 0000:00:13.0: auto-stop root hub
ehci_hcd 0000:00:13.2: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
ehci_hcd 0000:00:13.2: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 3-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 3 full speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 3 status 003801 POWER OWNER sig=j CONNECT
ohci_hcd 0000:00:13.0: auto-wakeup root hub
hub 3-0:1.0: port 3 not reset yet, waiting 50ms
ehci_hcd 0000:00:13.2: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC
ehci_hcd 0000:00:13.2: GetStatus port 6 status 001403 POWER sig=k CSC CONNECT
hub 3-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
hub 3-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 6 low speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 6 status 003002 POWER OWNER sig=se0 CSC
hub 3-0:1.0: state 7 ports 8 chg 0000 evt 0040
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0002
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 2-1: new full speed USB device using ohci_hcd and address 2
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04793/0x300000
serio: Synaptics pass-through port at isa0060/serio4/input0
usb 2-1: ep0 maxpacket = 8
usb 2-1: default language 0x0409
usb 2-1: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-1: Product: Fingerprint Sensor
usb 2-1: uevent
usb 2-1: usb_probe_device
usb 2-1: configuration #1 chosen from 1 choice
input: SynPS/2 Synaptics TouchPad as /class/input/input2
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: uevent
usb 2-1:1.0: uevent
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00010301 CSC LSDA PPS CCS
hub 2-0:1.0: port 3, status 0301, change 0001, 1.5 Mb/s
hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS
usb 2-3: new low speed USB device using ohci_hcd and address 3
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS
usb 2-3: skipped 1 descriptor after interface
usb 2-3: skipped 1 descriptor after interface
usb 2-3: default language 0x0409
usb 2-3: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-3: Product: USB Receiver
usb 2-3: Manufacturer: Logitech
usb 2-3: uevent
usb 2-3: usb_probe_device
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: adding 2-3:1.0 (config #1, interface 0)
usb 2-3:1.0: uevent
usb 2-3:1.0: uevent
usb 2-3: adding 2-3:1.1 (config #1, interface 1)
usb 2-3:1.1: uevent
usb 2-3:1.1: uevent
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '003'
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0004
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 1-2: new full speed USB device using ohci_hcd and address 3
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
usb 1-2: skipped 1 descriptor after interface
usb 1-2: default language 0x0409
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2: Product: HP Integrated Module
usb 1-2: Manufacturer: Broadcom Corp
usb 1-2: uevent
usb 1-2: usb_probe_device
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2: adding 1-2:1.1 (config #1, interface 1)
usb 1-2:1.1: uevent
usb 1-2:1.1: uevent
usb 1-2: adding 1-2:1.2 (config #1, interface 2)
usb 1-2:1.2: uevent
usb 1-2:1.2: uevent
usb 1-2: adding 1-2:1.3 (config #1, interface 3)
usb 1-2:1.3: uevent
usb 1-2:1.3: uevent
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/inode.c: creating file '003'
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0008
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0004
usbcore: registered new interface driver hiddev
usbhid 2-3:1.0: usb_probe_interface
usbhid 2-3:1.0: usb_probe_interface - got id
input: Logitech USB Receiver as /class/input/input3
input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-3
usbhid 2-3:1.1: usb_probe_interface
usbhid 2-3:1.1: usb_probe_interface - got id
input: Logitech USB Receiver as /class/input/input4
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/usb/core/file.c: looking for a minor, starting at 96
input,hiddev96: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:13.1-3
usbcore: registered new interface driver usbhid
/home/rafael/tmp/kernel/linux-2.6.23-rc6/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
ehci_hcd 0000:00:13.2: suspend root hub
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: HCI USB driver ver 2.9
hci_usb 1-2:1.0: usb_probe_interface
hci_usb 1-2:1.0: usb_probe_interface - got id
usb_endpoint usbdev1.3_ep83: ep_device_release called for usbdev1.3_ep83
usb_endpoint usbdev1.3_ep03: ep_device_release called for usbdev1.3_ep03
hci_usb 1-2:1.2: usb_probe_interface
hci_usb 1-2:1.2: usb_probe_interface - got id
hci_usb 1-2:1.3: usb_probe_interface
hci_usb 1-2:1.3: usb_probe_interface - got id
usbcore: registered new interface driver hci_usb
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
usb 2-1: usb auto-suspend
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
loop: module loaded
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
Adding 1052216k swap on /dev/sda1.  Priority:-1 extents:1 across:1052216k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ACPI: AC Adapter [C1BD] (on-line)
ACPI: Battery Slot [C1BF] (battery present)
ACPI: Battery Slot [C1BE] (battery absent)
input: Power Button (FF) as /class/input/input5
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [C25A]
input: Lid Switch as /class/input/input7
ACPI: Lid Switch [C25B]
ACPI: Transitioning device [C34F] to D3
ACPI: Transitioning device [C34F] to D3
ACPI: Fan [C34F] (off)
ACPI: Transitioning device [C350] to D3
ACPI: Transitioning device [C350] to D3
ACPI: Fan [C350] (off)
ACPI: Transitioning device [C351] to D3
ACPI: Transitioning device [C351] to D3
ACPI: Fan [C351] (off)
ACPI: Transitioning device [C352] to D3
ACPI: Transitioning device [C352] to D3
ACPI: Fan [C352] (off)
ACPI: Processor [C000] (supports 8 throttling states)
ACPI: Processor [C001] (supports 8 throttling states)
ACPI: Thermal Zone [TZ1] (59 C)
ACPI: Thermal Zone [TZ2] (50 C)
ACPI: Thermal Zone [TZ3] (30 C)
powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-60 processors (2 cpu cores) (version 2.00.00)
powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x13
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x15
powernow-k8:    2 : fid 0x8 (1600 MHz), vid 0x17
powernow-k8:    3 : fid 0x0 (800 MHz), vid 0x1e
powernow-k8: ph2 null fid transition 0xc

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Thomas Gleixner]

On Mon, 2007-09-24 at 14:57 +0200, Rafael J. Wysocki wrote:
> > > http://tglx.de/projects/hrtimers/2.6.23-rc4/patch-2.6.23-rc4-hrt1.patches.tar.bz2
> > > 
> > > applied.  I also have the 2.6.23-rc6-mm1 dmesg output ready, but there's some
> > > -mm-specific noise in it.  Please let me know if you want it, though.
> > 
> > Hmm:
> > 
> > > Command line: root=/dev/sda3 vga=792 resume=/dev/sda1 noacpitimer apic=verbose 2
> > --------------------------------------------------------^^^^^^^^^^^
> > 
> > noacpitimer is not a valid commandline option.
> > 
> > I asked for: 
> > >> > > noapictimer
> 
> I'm blind, sorry.
> 
> > So I really wonder, why noacpitimer on the kernel command line makes any
> > difference. I'm confused.
> 
> \metoo
> 
> Well, it was probably read as "noacpi". :-)

Hmm, ACPI is in the log all over the place.

> Fortunately, noapictimer helps as well, dmesg attached (I have the one
> from 2.6.23-rc6-mm1 ready, too).

Ok, at which point is the box stopping, when you omit noa* ? Is
earlyprintk giving you any useful info ?

	tglx

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

On Monday, 24 September 2007 15:05, Thomas Gleixner wrote:
> On Mon, 2007-09-24 at 14:57 +0200, Rafael J. Wysocki wrote:
> > > > http://tglx.de/projects/hrtimers/2.6.23-rc4/patch-2.6.23-rc4-hrt1.patches.tar.bz2
> > > > 
> > > > applied.  I also have the 2.6.23-rc6-mm1 dmesg output ready, but there's some
> > > > -mm-specific noise in it.  Please let me know if you want it, though.
> > > 
> > > Hmm:
> > > 
> > > > Command line: root=/dev/sda3 vga=792 resume=/dev/sda1 noacpitimer apic=verbose 2
> > > --------------------------------------------------------^^^^^^^^^^^
> > > 
> > > noacpitimer is not a valid commandline option.
> > > 
> > > I asked for: 
> > > >> > > noapictimer
> > 
> > I'm blind, sorry.
> > 
> > > So I really wonder, why noacpitimer on the kernel command line makes any
> > > difference. I'm confused.
> > 
> > \metoo
> > 
> > Well, it was probably read as "noacpi". :-)
> 
> Hmm, ACPI is in the log all over the place.

Well, "noacpi" seems to be a synonym for "pci=noacpi".

Anyway, it causes acpi_disable_pci() to be executed, which according to
Documentation/kernel-parameters.txt means "Do not use ACPI for IRQ routing or
for PCI scanning" (it works like this on x86_64 too, although the doc says it's
x86_32-specific).

And yes, it matches "noacpiwhatever" in the command line with "noacpi".  Sigh.

> > Fortunately, noapictimer helps as well, dmesg attached (I have the one
> > from 2.6.23-rc6-mm1 ready, too).
> 
> Ok, at which point is the box stopping, when you omit noa* ? Is
> earlyprintk giving you any useful info ?

earlyprintk=vga doesn't display anything (ie. black screen) and there are no
serial ports in the box.

Greetings,
Rafael

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Thomas Gleixner]

On Mon, 2007-09-24 at 15:52 +0200, Rafael J. Wysocki wrote:
> > > > So I really wonder, why noacpitimer on the kernel command line makes any
> > > > difference. I'm confused.
> > > 
> > > \metoo
> > > 
> > > Well, it was probably read as "noacpi". :-)
> > 
> > Hmm, ACPI is in the log all over the place.
> 
> Well, "noacpi" seems to be a synonym for "pci=noacpi".
> 
> Anyway, it causes acpi_disable_pci() to be executed, which according to
> Documentation/kernel-parameters.txt means "Do not use ACPI for IRQ routing or
> for PCI scanning" (it works like this on x86_64 too, although the doc says it's
> x86_32-specific).

Hrm. The local apic timer calibration does not use anything which is
related to interrupts, but if we use the local APIC timer we switch off
PIT.

Can you boot Linus latest (w/o hrt patches) and add "apicmaintimer" to
the kernel command line please ?

> And yes, it matches "noacpiwhatever" in the command line with "noacpi".  Sigh.

Urgh.

	tglx

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

[-- Attachment #1: Type: text/plain, Size: 1024 bytes --]

On Monday, 24 September 2007 16:23, Thomas Gleixner wrote:
> On Mon, 2007-09-24 at 15:52 +0200, Rafael J. Wysocki wrote:
> > > > > So I really wonder, why noacpitimer on the kernel command line makes any
> > > > > difference. I'm confused.
> > > > 
> > > > \metoo
> > > > 
> > > > Well, it was probably read as "noacpi". :-)
> > > 
> > > Hmm, ACPI is in the log all over the place.
> > 
> > Well, "noacpi" seems to be a synonym for "pci=noacpi".
> > 
> > Anyway, it causes acpi_disable_pci() to be executed, which according to
> > Documentation/kernel-parameters.txt means "Do not use ACPI for IRQ routing or
> > for PCI scanning" (it works like this on x86_64 too, although the doc says it's
> > x86_32-specific).
> 
> Hrm. The local apic timer calibration does not use anything which is
> related to interrupts, but if we use the local APIC timer we switch off
> PIT.
> 
> Can you boot Linus latest (w/o hrt patches) and add "apicmaintimer" to
> the kernel command line please ?

Works, dmesg attached.

Greetings,
Rafael

[-- Attachment #2: 2.6.23-rc7test.log --]
[-- Type: text/x-log, Size: 41551 bytes --]

Linux version 2.6.23-rc7test (rafael@albercik) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #19 SMP Mon Sep 24 16:55:05 CEST 2007
Command line: root=/dev/sda3 vga=792 resume=/dev/sda1 apicmaintimer apic=verbose 2
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000077fd0000 (usable)
 BIOS-e820: 0000000077fd0000 - 0000000077fe5600 (reserved)
 BIOS-e820: 0000000077fe5600 - 0000000077ff8000 (ACPI NVS)
 BIOS-e820: 0000000077ff8000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved)
 BIOS-e820: 00000000ffbc0000 - 00000000ffcc0000 (reserved)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 491472) 1 entries of 256 used
end_pfn_map = 1048576
DMI 2.4 present.
ACPI: RSDP 000F7D30, 0024 (r2 HP    )
ACPI: XSDT 77FE57B4, 0054 (r1 HP     0944      6070620 HP          1)
ACPI: FACP 77FE5684, 00F4 (r4 HP     0944            3 HP          1)
ACPI: DSDT 77FE58DC, EE7A (r1 HP        SB400    10000 MSFT  100000E)
ACPI: FACS 77FF7E80, 0040
ACPI: APIC 77FE5808, 0062 (r1 HP     0944            1 HP          1)
ACPI: MCFG 77FE586C, 003C (r1 HP     0944            1 HP          1)
ACPI: TCPA 77FE58A8, 0032 (r2 HP     0944            1 HP          1)
ACPI: SSDT 77FF4756, 0059 (r1 HP       HPQNLP        1 MSFT  100000E)
ACPI: SSDT 77FF47AF, 0206 (r1 HP     PSSTBLID        1 HP          1)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 491472) 1 entries of 256 used
No mptable found.
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0:        0 ->      159
    0:      256 ->   491472
On node 0 totalpages: 491375
  DMA zone: 56 pages used for memmap
  DMA zone: 1442 pages reserved
  DMA zone: 2501 pages, LIFO batch:0
  DMA32 zone: 6663 pages used for memmap
  DMA32 zone: 480713 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
mapped APIC to ffffffffff5fb000 (        fee00000)
mapped IOAPIC to ffffffffff5fa000 (00000000fec00000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 47320 bytes of per cpu data
Built 1 zonelists in Zone order.  Total pages: 483214
Kernel command line: root=/dev/sda3 vga=792 resume=/dev/sda1 apicmaintimer apic=verbose 2
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 1995.108 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ 1c8000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 1924072k/1965888k available (2196k kernel code, 41144k reserved, 1433k data, 248k init)
Calibrating delay using timer specific routine.. 3994.18 BogoMIPS (lpj=7988376)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Parsing all Control Methods:
Table [DSDT](id 0001) - 1153 Objects with 113 Devices 337 Methods 33 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 2 Objects with 0 Devices 2 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0003) - 8 Objects with 0 Devices 0 Methods 0 Regions
 tbxface-0598 [00] tb_load_namespace     : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable                : Transition to ACPI mode successful
enabled ExtINT on CPU#0
ENABLING IO-APIC IRQs
init IO_APIC IRQs
 IO-APIC (apicid-pin) 2-0<7>IOAPIC[0]: Set routing entry (2-1 -> 0x31 -> IRQ 1 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-2 -> 0x30 -> IRQ 0 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-3 -> 0x33 -> IRQ 3 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-4 -> 0x34 -> IRQ 4 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-5 -> 0x35 -> IRQ 5 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-6 -> 0x36 -> IRQ 6 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-7 -> 0x37 -> IRQ 7 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-8 -> 0x38 -> IRQ 8 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-9 -> 0x39 -> IRQ 9 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-10 -> 0x3a -> IRQ 10 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-11 -> 0x3b -> IRQ 11 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-12 -> 0x3c -> IRQ 12 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-13 -> 0x3d -> IRQ 13 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-14 -> 0x3e -> IRQ 14 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-15 -> 0x3f -> IRQ 15 Mode:0 Active:0)
, 2-16, 2-17, 2-18, 2-19, 2-20<7>IOAPIC[0]: Set routing entry (2-21 -> 0x49 -> IRQ 21 Mode:1 Active:1)
, 2-22, 2-23 not connected.
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...  failed.
...trying to set up timer as Virtual Wire IRQ... works.
Using local APIC timer interrupts.
result 12469442
Detected 12.469 MHz APIC timer.
timer: PIT interrupt stopped.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
masked ExtINT on CPU#1
Calibrating delay using timer specific routine.. 3990.23 BogoMIPS (lpj=7980478)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Turion(tm) 64 X2 Mobile Technology TL-60 stepping 02
Brought up 2 CPUs
Time: 15:06:59  Date: 08/24/107
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: No mmconfig possible on device 00:18
evgpeblk-0956 [00] ev_create_gpe_block   : GPE 00 to 1F [_GPE] 4 regs on int 0x15
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 3 Wake, Enabled 11 Runtime GPEs in this block
ACPI: EC: Look up EC in DSDT
ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
Completing Region/Field/Buffer/Package initialization:................................................................................................................................................................
Initialized 29/33 Regions 0/0 Fields 63/64 Buffers 68/78 Packages (1172 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:.......
Executed 7 _INI methods requiring 2 _STA executions (examined 120 objects)
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [C074] (0000:00)
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.C074._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C074.C075._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C074.C0DF._PRT]
ACPI: PCI Interrupt Link [C125] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C126] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C127] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C128] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C129] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C12A] (IRQs 9) *0, disabled.
ACPI: PCI Interrupt Link [C12B] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C12C] (IRQs *10 11)
ACPI: Power Resource [C223] (off)
ACPI: Power Resource [C1FE] (off)
ACPI: Power Resource [C217] (on)
ACPI: Power Resource [C34B] (off)
ACPI: Power Resource [C34C] (off)
ACPI: Power Resource [C34D] (off)
ACPI: Power Resource [C34E] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
IOAPIC[0]: Set routing entry (2-13 -> 0x3d -> IRQ 13 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-8 -> 0x38 -> IRQ 8 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-1 -> 0x31 -> IRQ 1 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (2-12 -> 0x3c -> IRQ 12 Mode:0 Active:0)
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 00000000
.......    : physical APIC id: 00
.... register #01: 00178021
.......     : max redirection entries: 0017
.......     : PRQ implemented: 1
.......     : IO APIC version: 0021
.... register #02: 00000000
.......     : arbitration: 00
.... IRQ redirection table:
 NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:   
 00 000 1    0    0   0   0    0    0    00
 01 003 0    0    0   0   0    1    1    31
 02 003 1    0    0   0   0    0    0    30
 03 003 0    0    0   0   0    1    1    33
 04 003 0    0    0   0   0    1    1    34
 05 003 0    0    0   0   0    1    1    35
 06 003 0    0    0   0   0    1    1    36
 07 003 0    0    0   0   0    1    1    37
 08 003 0    0    0   0   0    1    1    38
 09 003 1    0    0   0   0    1    1    39
 0a 003 0    0    0   0   0    1    1    3A
 0b 003 0    0    0   0   0    1    1    3B
 0c 003 0    0    0   0   0    1    1    3C
 0d 003 0    0    0   0   0    1    1    3D
 0e 003 0    0    0   0   0    1    1    3E
 0f 003 0    0    0   0   0    1    1    3F
 10 000 1    0    0   0   0    0    0    00
 11 000 1    0    0   0   0    0    0    00
 12 000 1    0    0   0   0    0    0    00
 13 000 1    0    0   0   0    0    0    00
 14 000 1    0    0   0   0    0    0    00
 15 003 0    1    0   1   0    1    1    49
 16 000 1    0    0   0   0    0    0    00
 17 000 1    0    0   0   0    0    0    00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ21 -> 0:21
.................................... done.
PCI: Cannot allocate resource region 0 of device 0000:00:14.2
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
ACPI: RTC can wake from S4
pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:00: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:00: iomem range 0x100000-0x77ffffff could not be reserved
pnp: 00:0a: ioport range 0x40b-0x40b has been reserved
pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0a: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:0a: iomem range 0xffb00000-0xffbfffff could not be reserved
pnp: 00:0a: iomem range 0xfff00000-0xffffffff could not be reserved
pnp: 00:0b: ioport range 0x8000-0x802f has been reserved
pnp: 00:0b: ioport range 0x8100-0x811f has been reserved
pnp: 00:0b: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:0c: iomem range 0xcf000-0xcffff has been reserved
pnp: 00:0c: iomem range 0x78000000-0x7fffffff could not be reserved
pnp: 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: 6000-6fff
  MEM window: d4300000-d43fffff
  PREFETCH window: c0000000-c7ffffff
PCI: Bridge: 0000:00:04.0
  IO window: 4000-5fff
  MEM window: d0000000-d3ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:05.0
  IO window: 2000-3fff
  MEM window: cc000000-cfffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
  IO window: disabled.
  MEM window: c8000000-c80fffff
  PREFETCH window: disabled.
PCI: Bus 3, cardbus bridge: 0000:02:04.0
  IO window: 00001000-000010ff
  IO window: 00001400-000014ff
  PREFETCH window: 88000000-8bffffff
  MEM window: 90000000-93ffffff
PCI: Bridge: 0000:00:14.4
  IO window: 1000-1fff
  MEM window: d4000000-d42fffff
  PREFETCH window: 88000000-8bffffff
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:05.0 to 64
PCI: Setting latency timer of device 0000:00:06.0 to 64
IOAPIC[0]: Set routing entry (2-20 -> 0x51 -> IRQ 20 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 20 (level, low) -> IRQ 20
NET: Registered protocol family 2
Time: acpi_pm clocksource has been installed.
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 5222k freed
audit: initializing netlink socket (disabled)
audit(1190646419.972:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: MSI quirk detected. MSI deactivated.
Boot video device is 0000:01:05.0
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie01]
Allocate Port Service[0000:00:04.0:pcie03]
PCI: Setting latency timer of device 0000:00:05.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:05.0:pcie00]
Allocate Port Service[0000:00:05.0:pcie01]
Allocate Port Service[0000:00:05.0:pcie03]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
Allocate Port Service[0000:00:06.0:pcie01]
Allocate Port Service[0000:00:06.0:pcie03]
AER service couldn't init device 0000:00:04.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:05.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:06.0:pcie01 - no _OSC support
vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20010100000, using 4608k, total 16384k
vesafb: mode is 1024x768x24, linelength=3072, pages=6
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize
sata_sil 0000:00:12.0: version 2.3
IOAPIC[0]: Set routing entry (2-16 -> 0x59 -> IRQ 16 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 16 (level, low) -> IRQ 16
scsi0 : sata_sil
scsi1 : sata_sil
ata1: SATA max UDMA/100 cmd 0xffffc2000002a080 ctl 0xffffc2000002a08a bmdma 0xffffc2000002a000 irq 16
ata2: SATA max UDMA/100 cmd 0xffffc2000002a0c0 ctl 0xffffc2000002a0ca bmdma 0xffffc2000002a008 irq 16
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: FUJITSU MHV2080BH, 892C, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA48 
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHV2080B 892C PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 0:0:0:0: [sda] Attached SCSI disk
PNP: PS/2 Controller [PNP0303:C214,PNP0f13:C215] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
NET: Registered protocol family 1
swsusp: Resume From Partition /dev/sda1
PM: Checking swsusp image.
PM: Resume from disk failed.
  Magic number: 7:477:134
  hash matches device device:09
Freeing unused kernel memory: 248k freed
Write protecting the kernel read-only data: 1056k
sd 0:0:0:0: Attached scsi generic sg0 type 0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
ATIIXP: chipset revision 128
ATIIXP: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x7040-0x7047, BIOS settings: hda:DMA, hdb:pio
ATIIXP: simplex device: DMA disabled
ide1: ATIIXP Bus-Master DMA disabled (BIOS)
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GMA-4082N, ATAPI CD/DVD-ROM drive
hda: selected mode 0x22
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
swsusp: Marking nosave pages: 000000000009f000 - 0000000000100000
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
Attempting manual resume
swsusp: Resume From Partition 8:1
PM: Checking swsusp image.
PM: Resume from disk failed.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Floppy drive(s): fd0 is 1.44M
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc_cmos: probe of 00:07 failed with error -16
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:02:04.3 [104c:803c] (rev 0)
ACPI: PCI Interrupt 0000:02:04.3[A] -> GSI 20 (level, low) -> IRQ 20
mmc0: SDHCI at 0xd4019000 irq 20 PIO
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 80 td 96
IOAPIC[0]: Set routing entry (2-19 -> 0x61 -> IRQ 19 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.0: OHCI Host Controller
/home/rafael/src/linux-2.6/drivers/usb/core/inode.c: creating file 'devices'
/home/rafael/src/linux-2.6/drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: created debug files
ohci_hcd 0000:00:13.0: irq 19, io mem 0xd4401000
ohci_hcd 0000:00:13.0: OHCI controller state
ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:13.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:13.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:13.0: intrenable 0x8000005a MIE RHSC UE RD WDH
ohci_hcd 0000:00:13.0: hcca frame #0005
ohci_hcd 0000:00:13.0: roothub.a 02000204 POTPGT=2 NPS NDP=4(4)
ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:13.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [3] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.23-rc7test ohci_hcd
usb usb1: SerialNumber: 0000:00:13.0
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 4ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: trying to enable port power on non-switchable hub
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0000
/home/rafael/src/linux-2.6/drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.1: OHCI Host Controller
/home/rafael/src/linux-2.6/drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.1: created debug files
ohci_hcd 0000:00:13.1: irq 19, io mem 0xd4402000
bcm43xx driver
ohci_hcd 0000:00:13.1: OHCI controller state
ohci_hcd 0000:00:13.1: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:13.1: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:13.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:13.1: intrstatus 0x00000004 SF
ohci_hcd 0000:00:13.1: intrenable 0x8000005a MIE RHSC UE RD WDH
ohci_hcd 0000:00:13.1: hcca frame #0005
ohci_hcd 0000:00:13.1: roothub.a 02000204 POTPGT=2 NPS NDP=4(4)
ohci_hcd 0000:00:13.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:13.1: roothub.status 00008000 DRWE
ohci_hcd 0000:00:13.1: roothub.portstatus [0] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:13.1: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:13.1: roothub.portstatus [2] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:13.1: roothub.portstatus [3] 0x00000100 PPS
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.23-rc7test ohci_hcd
usb usb2: SerialNumber: 0000:00:13.1
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 4ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: trying to enable port power on non-switchable hub
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
/home/rafael/src/linux-2.6/drivers/usb/core/inode.c: creating file '001'
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
IOAPIC[0]: Set routing entry (2-18 -> 0x69 -> IRQ 18 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:30:00.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:30:00.0 to 64
bcm43xx: Chip ID 0x4311, rev 0x1
usb 1-2: new full speed USB device using ohci_hcd and address 2
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0x11, vendor 0x4243
bcm43xx: Core 1: ID 0x812, rev 0xa, vendor 0x4243
bcm43xx: Core 2: ID 0x817, rev 0x3, vendor 0x4243
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
bcm43xx: Core 3: ID 0x820, rev 0x1, vendor 0x4243
bcm43xx: PHY connected
bcm43xx: Detected PHY: Analog: 4, Type 2, Revision 8
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
usb 1-2: skipped 1 descriptor after interface
usb 1-2: default language 0x0409
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2: Product: HP Integrated Module
usb 1-2: Manufacturer: Broadcom Corp
usb 1-2: uevent
usb 1-2: usb_probe_device
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2: adding 1-2:1.1 (config #1, interface 1)
usb 1-2:1.1: uevent
usb 1-2:1.1: uevent
usb 1-2: adding 1-2:1.2 (config #1, interface 2)
usb 1-2:1.2: uevent
usb 1-2:1.2: uevent
usb 1-2: adding 1-2:1.3 (config #1, interface 3)
usb 1-2:1.3: uevent
usb 1-2:1.3: uevent
/home/rafael/src/linux-2.6/drivers/usb/core/inode.c: creating file '002'
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0004
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 000a
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
ACPI: PCI Interrupt 0000:02:04.1[A] -> GSI 20 (level, low) -> IRQ 20
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20]  MMIO=[d4011000-d40117ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
tg3.c:v3.81 (September 5, 2007)
IOAPIC[0]: Set routing entry (2-23 -> 0x71 -> IRQ 23 Mode:1 Active:1)
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
eth1: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:17:08:2e:2e:f3
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1]
eth1: dma_rwctrl[763f0000] dma_mask[32-bit]
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
Yenta: CardBus bridge found at 0000:02:04.0 [103c:30b0]
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
Yenta: Enabling burst memory read transactions
ehci_hcd 0000:00:13.2: EHCI Host Controller
/home/rafael/src/linux-2.6/drivers/usb/core/inode.c: creating file '003'
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:13.2: reset hcs_params 0x2408 dbg=0 cc=2 pcc=4 ordered !ppc ports=8
ehci_hcd 0000:00:13.2: reset hcc_params a012 thresh 1 uframes 256/512/1024
ehci_hcd 0000:00:13.2: MWI active
ehci_hcd 0000:00:13.2: irq 19, io mem 0xd4403000
ehci_hcd 0000:00:13.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:13.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: EHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.23-rc7test ehci_hcd
usb usb3: SerialNumber: 0000:00:13.2
usb usb3: uevent
usb usb3: usb_probe_device
usb usb3: configuration #1 chosen from 1 choice
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: uevent
usb 3-0:1.0: uevent
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: Single TT
hub 3-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 3-0:1.0: power on to power good time: 20ms
hub 3-0:1.0: local power source is good
hub 3-0:1.0: trying to enable port power on non-switchable hub
Yenta: Using INTVAL to route CSC interrupts to PCI
usb 2-1: new full speed USB device using ohci_hcd and address 2
floppy0: no floppy controllers found
/home/rafael/src/linux-2.6/drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:13.1: urb ffff810075039158 path 1 ep0in 5ec20000 cc 5 --> status -62
ohci_hcd 0000:00:13.1: urb ffff810075039158 path 1 ep0in 5ec20000 cc 5 --> status -62
ohci_hcd 0000:00:13.1: urb ffff810075039158 path 1 ep0in 5ec20000 cc 5 --> status -62
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x01a11002, devctl 0x64
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00030100 PESC CSC PPS
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
hub 2-0:1.0: port 3, status 0100, change 0001, 12 Mb/s
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: HCI USB driver ver 2.9
net ethxx0: device_rename: sysfs_create_symlink failed (-17)
hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0002
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00030100 PESC CSC PPS
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
Yenta: ISA IRQ mask 0x0ef8, PCI irq 20
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0004
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00030100 PESC CSC PPS
hub 1-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
usb 1-2: USB disconnect, address 2
pcmcia: parent PCI bridge I/O window: 0x1000 - 0x1fff
pcmcia: parent PCI bridge Memory window: 0xd4000000 - 0xd42fffff
pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x8bffffff
hci_usb 1-2:1.0: usb_probe_interface
hci_usb 1-2:1.0: usb_probe_interface - got id
hci_usb_probe: Can't set isoc interface settings
hci_usb 1-2:1.1: usb_probe_interface
hci_usb 1-2:1.1: usb_probe_interface - got id
hci_usb 1-2:1.2: usb_probe_interface
hci_usb 1-2:1.2: usb_probe_interface - got id
hci_usb 1-2:1.3: usb_probe_interface
hci_usb 1-2:1.3: usb_probe_interface - got id
usb 1-2: unregistering device
usb 1-2: usb_disable_device nuking all URBs
usb 1-2: unregistering interface 1-2:1.0
usb_endpoint usbdev1.2_ep81: ep_device_release called for usbdev1.2_ep81
usb_endpoint usbdev1.2_ep82: ep_device_release called for usbdev1.2_ep82
usb_endpoint usbdev1.2_ep02: ep_device_release called for usbdev1.2_ep02
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2: unregistering interface 1-2:1.1
usb_endpoint usbdev1.2_ep83: ep_device_release called for usbdev1.2_ep83
usb_endpoint usbdev1.2_ep03: ep_device_release called for usbdev1.2_ep03
usb 1-2:1.1: uevent
usb 1-2:1.1: uevent
usb 1-2: unregistering interface 1-2:1.2
usb_endpoint usbdev1.2_ep84: ep_device_release called for usbdev1.2_ep84
usb_endpoint usbdev1.2_ep04: ep_device_release called for usbdev1.2_ep04
usb 1-2:1.2: uevent
usb 1-2:1.2: uevent
usb 1-2: unregistering interface 1-2:1.3
usb 1-2:1.3: uevent
usb 1-2:1.3: uevent
usb_endpoint usbdev1.2_ep00: ep_device_release called for usbdev1.2_ep00
usb 1-2: uevent
ACPI: PCI Interrupt 0000:02:04.2[A] -> GSI 20 (level, low) -> IRQ 20
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
net eth0: device_rename: sysfs_create_symlink failed (-17)
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 3-0:1.0: state 7 ports 8 chg 0000 evt 0000
ehci_hcd 0000:00:13.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 3-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
net eth1: device_rename: sysfs_create_symlink failed (-17)
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 2 full speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 2 status 003801 POWER OWNER sig=j CONNECT
hub 3-0:1.0: port 2 not reset yet, waiting 50ms
ehci_hcd 0000:00:13.2: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
ehci_hcd 0000:00:13.2: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 3-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023f9929613f0c]
ohci_hcd 0000:00:13.0: auto-stop root hub
hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 3 full speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 3 status 003801 POWER OWNER sig=j CONNECT
hub 3-0:1.0: port 3 not reset yet, waiting 50ms
ohci_hcd 0000:00:13.0: auto-wakeup root hub
ehci_hcd 0000:00:13.2: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC
ehci_hcd 0000:00:13.2: GetStatus port 6 status 001403 POWER sig=k CSC CONNECT
hub 3-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
hub 3-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 6 low speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 6 status 003002 POWER OWNER sig=se0 CSC
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0002
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
usbcore: registered new interface driver hci_usb
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 2-1: new full speed USB device using ohci_hcd and address 3
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
Bluetooth: RFCOMM socket layer initialized
usb 2-1: ep0 maxpacket = 8
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
usb 2-1: default language 0x0409
usb 2-1: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-1: Product: Fingerprint Sensor
usb 2-1: uevent
usb 2-1: usb_probe_device
usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: uevent
usb 2-1:1.0: uevent
/home/rafael/src/linux-2.6/drivers/usb/core/inode.c: creating file '003'
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00010301 CSC LSDA PPS CCS
hub 2-0:1.0: port 3, status 0301, change 0001, 1.5 Mb/s
hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS
usb 2-3: new low speed USB device using ohci_hcd and address 4
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS
usb 2-3: skipped 1 descriptor after interface
usb 2-3: skipped 1 descriptor after interface
usb 2-3: default language 0x0409
usb 2-3: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-3: Product: USB Receiver
usb 2-3: Manufacturer: Logitech
usb 2-3: uevent
usb 2-3: usb_probe_device
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: adding 2-3:1.0 (config #1, interface 0)
usb 2-3:1.0: uevent
usb 2-3:1.0: uevent
usb 2-3: adding 2-3:1.1 (config #1, interface 1)
usb 2-3:1.1: uevent
usb 2-3:1.1: uevent
/home/rafael/src/linux-2.6/drivers/usb/core/inode.c: creating file '004'
hub 3-0:1.0: state 7 ports 8 chg 0000 evt 0040
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0004
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 1-2: new full speed USB device using ohci_hcd and address 3
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 1-2: skipped 1 descriptor after interface
usb 1-2: default language 0x0409
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2: Product: HP Integrated Module
usb 1-2: Manufacturer: Broadcom Corp
usb 1-2: uevent
usb 1-2: usb_probe_device
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
hci_usb 1-2:1.0: usb_probe_interface
hci_usb 1-2:1.0: usb_probe_interface - got id
usb 1-2: adding 1-2:1.1 (config #1, interface 1)
usb 1-2:1.1: uevent
usb 1-2:1.1: uevent
usb 1-2: adding 1-2:1.2 (config #1, interface 2)
usb 1-2:1.2: uevent
usb 1-2:1.2: uevent
hci_usb 1-2:1.2: usb_probe_interface
hci_usb 1-2:1.2: usb_probe_interface - got id
usb 1-2: adding 1-2:1.3 (config #1, interface 3)
usb 1-2:1.3: uevent
usb 1-2:1.3: uevent
hci_usb 1-2:1.3: usb_probe_interface
hci_usb 1-2:1.3: usb_probe_interface - got id
/home/rafael/src/linux-2.6/drivers/usb/core/inode.c: creating file '003'
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0004
usbcore: registered new interface driver hiddev
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04793/0x300000
serio: Synaptics pass-through port at isa0060/serio4/input0
usbhid 2-3:1.0: usb_probe_interface
usbhid 2-3:1.0: usb_probe_interface - got id
input: Logitech USB Receiver as /class/input/input2
input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-3
usbhid 2-3:1.1: usb_probe_interface
usbhid 2-3:1.1: usb_probe_interface - got id
input: Logitech USB Receiver as /class/input/input3
/home/rafael/src/linux-2.6/drivers/usb/core/file.c: looking for a minor, starting at 96
input,hiddev96: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:13.1-3
input: SynPS/2 Synaptics TouchPad as /class/input/input4
usbcore: registered new interface driver usbhid
/home/rafael/src/linux-2.6/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
ehci_hcd 0000:00:13.2: suspend root hub
loop: module loaded
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
Adding 1052216k swap on /dev/sda1.  Priority:-1 extents:1 across:1052216k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ACPI: AC Adapter [C1BD] (on-line)
ACPI: Battery Slot [C1BF] (battery present)
ACPI: Battery Slot [C1BE] (battery absent)
input: Power Button (FF) as /class/input/input5
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [C25A]
input: Lid Switch as /class/input/input7
ACPI: Lid Switch [C25B]
ACPI: Transitioning device [C34F] to D3
ACPI: Transitioning device [C34F] to D3
ACPI: Fan [C34F] (off)
ACPI: Transitioning device [C350] to D3
ACPI: Transitioning device [C350] to D3
ACPI: Fan [C350] (off)
ACPI: Transitioning device [C351] to D3
ACPI: Transitioning device [C351] to D3
ACPI: Fan [C351] (off)
ACPI: Transitioning device [C352] to D3
ACPI: Transitioning device [C352] to D3
ACPI: Fan [C352] (off)
ACPI: Processor [C000] (supports 8 throttling states)
ACPI: Processor [C001] (supports 8 throttling states)
ACPI: Thermal Zone [TZ1] (61 C)
ACPI: Thermal Zone [TZ2] (51 C)
ACPI: Thermal Zone [TZ3] (32 C)
powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-60 processors (2 cpu cores) (version 2.00.00)
powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x13
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x15
powernow-k8:    2 : fid 0x8 (1600 MHz), vid 0x17
powernow-k8:    3 : fid 0x0 (800 MHz), vid 0x1e
powernow-k8: ph2 null fid transition 0xc

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Thomas Gleixner]

On Mon, 2007-09-24 at 17:18 +0200, Rafael J. Wysocki wrote:
> > > Well, "noacpi" seems to be a synonym for "pci=noacpi".
> > > 
> > > Anyway, it causes acpi_disable_pci() to be executed, which according to
> > > Documentation/kernel-parameters.txt means "Do not use ACPI for IRQ routing or
> > > for PCI scanning" (it works like this on x86_64 too, although the doc says it's
> > > x86_32-specific).
> > 
> > Hrm. The local apic timer calibration does not use anything which is
> > related to interrupts, but if we use the local APIC timer we switch off
> > PIT.
> > 
> > Can you boot Linus latest (w/o hrt patches) and add "apicmaintimer" to
> > the kernel command line please ?
> 
> Works, dmesg attached.

/me scratches head

We know, that
- disabling local apic timers work
- local apic timers (which turn off PIT) work. when noacpiFSCKEDPARSING
is given on the kernel command line.

I have no clue, what might be the difference of noacpiFSCKEDPARSING. The
boot log is not giving any hint at all.

acpi_disable_pci() sets acpi_pci_disabled and acpi_noirq to 1.

What happens, if you set "acpi=noirq" instead ?

	tglx

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

On Monday, 24 September 2007 18:46, Thomas Gleixner wrote:
> On Mon, 2007-09-24 at 17:18 +0200, Rafael J. Wysocki wrote:
> > > > Well, "noacpi" seems to be a synonym for "pci=noacpi".
> > > > 
> > > > Anyway, it causes acpi_disable_pci() to be executed, which according to
> > > > Documentation/kernel-parameters.txt means "Do not use ACPI for IRQ routing or
> > > > for PCI scanning" (it works like this on x86_64 too, although the doc says it's
> > > > x86_32-specific).
> > > 
> > > Hrm. The local apic timer calibration does not use anything which is
> > > related to interrupts, but if we use the local APIC timer we switch off
> > > PIT.
> > > 
> > > Can you boot Linus latest (w/o hrt patches) and add "apicmaintimer" to
> > > the kernel command line please ?
> > 
> > Works, dmesg attached.
> 
> /me scratches head

Retested.

> We know, that
> - disabling local apic timers work

This works reproducibly accross the board.

> - local apic timers (which turn off PIT) work. when noacpiFSCKEDPARSING

This stopped working, although it evidently worked yesterday (wtf?).

There seems to be a history effect in the box, to make things more
"interesting".

> is given on the kernel command line.
> 
> I have no clue, what might be the difference of noacpiFSCKEDPARSING. The
> boot log is not giving any hint at all.
> 
> acpi_disable_pci() sets acpi_pci_disabled and acpi_noirq to 1.
> 
> What happens, if you set "acpi=noirq" instead ?

That obviously doesn't help.

I think the only solid data point so far is that "noapictimer" makes the box
boot.

Greetings,
Rafael

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Thomas Gleixner]

On Mon, 2007-09-24 at 21:11 +0200, Rafael J. Wysocki wrote:
> > /me scratches head
> 
> Retested.
> 
> > We know, that
> > - disabling local apic timers work
> 
> This works reproducibly accross the board.

Ok

> > - local apic timers (which turn off PIT) work. when noacpiFSCKEDPARSING
> 
> This stopped working, although it evidently worked yesterday (wtf?).
> 
> There seems to be a history effect in the box, to make things more
> "interesting".

Did you connect this box to Andrews VAIO during KS ?

> I think the only solid data point so far is that "noapictimer" makes the box
> boot.

Ok. Can you add "nmi_watchdog=1" to the command line please. This runs
through the calibration of APIC, but registers it as a dummy clock
source (the PIT must run to make the watchdog work).

If it boots, please provide the output of /proc/timer_list

Thanks,	

	tlgx

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

On Monday, 24 September 2007 21:13, Thomas Gleixner wrote:
> On Mon, 2007-09-24 at 21:11 +0200, Rafael J. Wysocki wrote:
> > > /me scratches head
> > 
> > Retested.
> > 
> > > We know, that
> > > - disabling local apic timers work
> > 
> > This works reproducibly accross the board.
> 
> Ok
> 
> > > - local apic timers (which turn off PIT) work. when noacpiFSCKEDPARSING
> > 
> > This stopped working, although it evidently worked yesterday (wtf?).
> > 
> > There seems to be a history effect in the box, to make things more
> > "interesting".
> 
> Did you connect this box to Andrews VAIO during KS ?

No, but it's famous for being interestingly broken nevertheless.

> > I think the only solid data point so far is that "noapictimer" makes the box
> > boot.
> 
> Ok. Can you add "nmi_watchdog=1" to the command line please. This runs
> through the calibration of APIC, but registers it as a dummy clock
> source (the PIT must run to make the watchdog work).
> 
> If it boots, please provide the output of /proc/timer_list

No, it doesn't.

Greetings,
Rafael

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Thomas Gleixner]

On Tue, 2007-09-25 at 15:16 +0200, Rafael J. Wysocki wrote:
> > > There seems to be a history effect in the box, to make things more
> > > "interesting".
> > 
> > Did you connect this box to Andrews VAIO during KS ?
> 
> No, but it's famous for being interestingly broken nevertheless.

:)

> > > I think the only solid data point so far is that "noapictimer" makes the box
> > > boot.
> > 
> > Ok. Can you add "nmi_watchdog=1" to the command line please. This runs
> > through the calibration of APIC, but registers it as a dummy clock
> > source (the PIT must run to make the watchdog work).
> > 
> > If it boots, please provide the output of /proc/timer_list
> 
> No, it doesn't.

I start to get desperate. Below is a patch, which moves the apic timer
disable check after the calibration routine. Can you please apply on top
of -hrt and add "noapictimer" to the command line ? Does it boot ?

	tglx

Index: linux-2.6.23-rc7/arch/x86_64/kernel/apic.c
===================================================================
--- linux-2.6.23-rc7.orig/arch/x86_64/kernel/apic.c	2007-09-24 20:30:00.000000000 +0200
+++ linux-2.6.23-rc7/arch/x86_64/kernel/apic.c	2007-09-25 15:05:32.000000000 +0200
@@ -927,6 +927,7 @@ static void __init calibrate_APIC_clock(
 
 void __init setup_boot_APIC_clock (void)
 {
+#if 0
 	/*
 	 * The local apic timer can be disabled via the kernel commandline.
 	 * Register the lapic timer as a dummy clock event source on SMP
@@ -940,7 +941,7 @@ void __init setup_boot_APIC_clock (void)
 			setup_APIC_timer();
 		return;
 	}
-
+#endif
 	printk(KERN_INFO "Using local APIC timer interrupts.\n");
 	calibrate_APIC_clock();
 
@@ -949,11 +950,13 @@ void __init setup_boot_APIC_clock (void)
 	 * PIT/HPET going.  Otherwise register lapic as a dummy
 	 * device.
 	 */
-	if (nmi_watchdog != NMI_IO_APIC)
+	if (!disable_apic_timer && nmi_watchdog != NMI_IO_APIC)
 		lapic_clockevent.features &= ~CLOCK_EVT_FEAT_DUMMY;
+#if 0
 	else
 		printk(KERN_WARNING "APIC timer registered as dummy,"
 		       " due to nmi_watchdog=1!\n");
+#endif
 
 	setup_APIC_timer();
 }

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

[-- Attachment #1: Type: text/plain, Size: 1948 bytes --]

On Tuesday, 25 September 2007 15:17, Thomas Gleixner wrote:
> On Tue, 2007-09-25 at 15:16 +0200, Rafael J. Wysocki wrote:
[--snip--]
> 
> I start to get desperate. Below is a patch, which moves the apic timer
> disable check after the calibration routine. Can you please apply on top
> of -hrt and add "noapictimer" to the command line ? Does it boot ?

2.6.23-rc7 with patch-2.6.23-rc7-hrt1.patch and the patch below applied boots
with noapictimer and doesn't boot without it.

Also, attached is the output of

# cat /proc/interrupts; sleep 10; cat /proc/interrupts

from the current mainline.

Greetings,
Rafael


> Index: linux-2.6.23-rc7/arch/x86_64/kernel/apic.c
> ===================================================================
> --- linux-2.6.23-rc7.orig/arch/x86_64/kernel/apic.c	2007-09-24 20:30:00.000000000 +0200
> +++ linux-2.6.23-rc7/arch/x86_64/kernel/apic.c	2007-09-25 15:05:32.000000000 +0200
> @@ -927,6 +927,7 @@ static void __init calibrate_APIC_clock(
>  
>  void __init setup_boot_APIC_clock (void)
>  {
> +#if 0
>  	/*
>  	 * The local apic timer can be disabled via the kernel commandline.
>  	 * Register the lapic timer as a dummy clock event source on SMP
> @@ -940,7 +941,7 @@ void __init setup_boot_APIC_clock (void)
>  			setup_APIC_timer();
>  		return;
>  	}
> -
> +#endif
>  	printk(KERN_INFO "Using local APIC timer interrupts.\n");
>  	calibrate_APIC_clock();
>  
> @@ -949,11 +950,13 @@ void __init setup_boot_APIC_clock (void)
>  	 * PIT/HPET going.  Otherwise register lapic as a dummy
>  	 * device.
>  	 */
> -	if (nmi_watchdog != NMI_IO_APIC)
> +	if (!disable_apic_timer && nmi_watchdog != NMI_IO_APIC)
>  		lapic_clockevent.features &= ~CLOCK_EVT_FEAT_DUMMY;
> +#if 0
>  	else
>  		printk(KERN_WARNING "APIC timer registered as dummy,"
>  		       " due to nmi_watchdog=1!\n");
> +#endif
>  
>  	setup_APIC_timer();
>  }
> 
> 
> 
> 

-- 
"Premature optimization is the root of all evil." - Donald Knuth

[-- Attachment #2: interrupts.txt --]
[-- Type: text/x-log, Size: 1395 bytes --]

albercik:~ # cat /proc/interrupts; sleep 10; cat /proc/interrupts
           CPU0       CPU1
  0:      62489          0  local-APIC-edge      timer
  1:          3        232   IO-APIC-edge      i8042
  8:          0          0   IO-APIC-edge      rtc
 12:          1        147   IO-APIC-edge      i8042
 14:         15       1947   IO-APIC-edge      ide0
 16:        193      14151   IO-APIC-fasteoi   sata_sil, HDA Intel
 19:         76      43153   IO-APIC-fasteoi   ohci_hcd:usb1, ehci_hcd:usb2, ohci_hcd:usb3
 20:          0          4   IO-APIC-fasteoi   ohci1394, tifm_7xx1, yenta, sdhci:slot0
 21:          7        172   IO-APIC-fasteoi   acpi
NMI:          0          0
LOC:      62454      62082
ERR:          0
           CPU0       CPU1
  0:      64993          0  local-APIC-edge      timer
  1:          3        233   IO-APIC-edge      i8042
  8:          0          0   IO-APIC-edge      rtc
 12:          1        147   IO-APIC-edge      i8042
 14:         15       2037   IO-APIC-edge      ide0
 16:        194      14265   IO-APIC-fasteoi   sata_sil, HDA Intel
 19:         77      45155   IO-APIC-fasteoi   ohci_hcd:usb1, ehci_hcd:usb2, ohci_hcd:usb3
 20:          0          4   IO-APIC-fasteoi   ohci1394, tifm_7xx1, yenta, sdhci:slot0
 21:          7        176   IO-APIC-fasteoi   acpi
NMI:          0          0
LOC:      64958      64586
ERR:          0
albercik:~ #

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Thomas Gleixner]

Rafael,

On Tue, 2007-09-25 at 22:07 +0200, Rafael J. Wysocki wrote:
> On Tuesday, 25 September 2007 15:17, Thomas Gleixner wrote:
> > On Tue, 2007-09-25 at 15:16 +0200, Rafael J. Wysocki wrote:
> [--snip--]
> > 
> > I start to get desperate. Below is a patch, which moves the apic timer
> > disable check after the calibration routine. Can you please apply on top
> > of -hrt and add "noapictimer" to the command line ? Does it boot ?
>
> 2.6.23-rc7 with patch-2.6.23-rc7-hrt1.patch and the patch below applied boots
> with noapictimer and doesn't boot without it.

That was expected. I explicitly asked to add "noapictimer" to the kernel
command line.

Ok, so we ruled out the apic timer calibration routine. I did not expect
that this would be the culprit, but with "dark screen" as the only debug
info, I need to resort to small steps.

Can you please send me the output of /proc/timer_list of 2.6.23-rc7-hrt1
after booting with "noapictimer" ?

I'm a bit confused by your earlier confirmation, that mainline w/o the
-hrt patches boots fine, when you add "apicmaintimer" to the kernel
command line. "apicmaintimer" stops the PIT like we do in -hrt and we
just use the local APIC timer for everything. Can you please retest and
confirm that this is correct ?

Is the 32 bit kernel working on that box ?

Thanks for your patience.

	tglx

PS: I just sent out the "disable APIC timer for AMD C1E boxen" patch. We
debugged this half a year ago on a nx6325, but I completely forgot about
that. The explanation from AMD was sensible, but your "apicmaintimer"
works statement is contradictory.

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

[-- Attachment #1: Type: text/plain, Size: 2670 bytes --]

Thomas,

On Tuesday, 25 September 2007 22:46, Thomas Gleixner wrote:
> Rafael,
> 
> On Tue, 2007-09-25 at 22:07 +0200, Rafael J. Wysocki wrote:
> > On Tuesday, 25 September 2007 15:17, Thomas Gleixner wrote:
> > > On Tue, 2007-09-25 at 15:16 +0200, Rafael J. Wysocki wrote:
> > [--snip--]
> > > 
> > > I start to get desperate. Below is a patch, which moves the apic timer
> > > disable check after the calibration routine. Can you please apply on top
> > > of -hrt and add "noapictimer" to the command line ? Does it boot ?
> >
> > 2.6.23-rc7 with patch-2.6.23-rc7-hrt1.patch and the patch below applied boots
> > with noapictimer and doesn't boot without it.
> 
> That was expected. I explicitly asked to add "noapictimer" to the kernel
> command line.
> 
> Ok, so we ruled out the apic timer calibration routine. I did not expect
> that this would be the culprit, but with "dark screen" as the only debug
> info, I need to resort to small steps.
> 
> Can you please send me the output of /proc/timer_list of 2.6.23-rc7-hrt1
> after booting with "noapictimer" ?

Sure, attached.  [Note: the kernel has been compiled with both NO_HZ and
HIGH_RES_TIMERS unset.]

> I'm a bit confused by your earlier confirmation, that mainline w/o the
> -hrt patches boots fine, when you add "apicmaintimer" to the kernel
> command line. "apicmaintimer" stops the PIT like we do in -hrt and we
> just use the local APIC timer for everything. Can you please retest and
> confirm that this is correct ?

No, it's not.  The mainline _usually_ doesn't boot with "apicmaintimer".

It seems to me that _sometimes_ the CPU just doesn't enter this C1E state
and then everything goes fine ...

> Is the 32 bit kernel working on that box ?

Can't tell, I have only 64-bit userland here.

> Thanks for your patience.

Well, I'm only making sure that future kernels will run on my box. ;-)

> 	tglx
> 
> PS: I just sent out the "disable APIC timer for AMD C1E boxen" patch.

Yes, I've already tested it and sent a reply.  It works. :-)

> We debugged this half a year ago on a nx6325, but I completely forgot about
> that. The explanation from AMD was sensible, but your "apicmaintimer"
> works statement is contradictory.

Well, it was wrong.

I have some problems with resuming from suspend to RAM using 2.6.23-rc8-mm1
with this patch applied, but I think they are related to something else.  I'll
wait for the next -mm with debugging that.

For now, I'm going to build 2.6.23-rc8 with my collection of suspend patches
plus patch-2.6.23-rc7-hrt1.patch and the "disable APIC timer for AMD C1E boxes"
patch applied.  I'll play with that a bit and let you know how it's behaving.

Greetings,
Rafael

[-- Attachment #2: timer_list.txt --]
[-- Type: text/plain, Size: 3052 bytes --]

Timer List Version: v0.3
HRTIMER_MAX_CLOCK_BASES: 2
now at 279792107058 nsecs

cpu: 0
 clock 0:
  .index:      0
  .resolution: 4000250 nsecs
  .get_time:   ktime_get_real
active timers:
 clock 1:
  .index:      1
  .resolution: 4000250 nsecs
  .get_time:   ktime_get
active timers:
 #0: <ffff81004f98bda8>, hrtimer_wakeup, S:01, do_nanosleep, kwrapper/4664
 # expires at 280207419178 nsecs [in 415312120 nsecs]
 #1: <ffff81004f98bda8>, hrtimer_wakeup, S:01, futex_wait, nscd/4080
 # expires at 282678021548 nsecs [in 2885914490 nsecs]
 #2: <ffff81004f98bda8>, hrtimer_wakeup, S:01, futex_wait, nscd/4082
 # expires at 282678129670 nsecs [in 2886022612 nsecs]
 #3: <ffff81004f98bda8>, it_real_fn, S:01, do_setitimer, qmgr/4239
 # expires at 378654389676 nsecs [in 98862282618 nsecs]
 #4: <ffff81004f98bda8>, it_real_fn, S:01, do_setitimer, pickup/4238
 # expires at 557809025993 nsecs [in 278016918935 nsecs]
 #5: <ffff81004f98bda8>, it_real_fn, S:01, do_setitimer, master/4216
 # expires at 557809137746 nsecs [in 278017030688 nsecs]

cpu: 1
 clock 0:
  .index:      0
  .resolution: 4000250 nsecs
  .get_time:   ktime_get_real
active timers:
 clock 1:
  .index:      1
  .resolution: 4000250 nsecs
  .get_time:   ktime_get
active timers:
 #0: <ffff81004f98bda8>, it_real_fn, S:01, do_setitimer, Xorg/4355
 # expires at 279804542721 nsecs [in 12435663 nsecs]
 #1: <ffff81004f98bda8>, it_real_fn, S:01, do_setitimer, ssh-agent/4611
 # expires at 279962268496 nsecs [in 170161438 nsecs]
 #2: <ffff81004f98bda8>, hrtimer_wakeup, S:01, do_nanosleep, hald-addon-stor/4148
 # expires at 280071774352 nsecs [in 279667294 nsecs]
 #3: <ffff81004f98bda8>, hrtimer_wakeup, S:01, futex_wait, nscd/4081
 # expires at 282678034680 nsecs [in 2885927622 nsecs]
 #4: <ffff81004f98bda8>, hrtimer_wakeup, S:01, do_nanosleep, cron/4241
 # expires at 335311096287 nsecs [in 55518989229 nsecs]
 #5: <ffff81004f98bda8>, it_real_fn, S:01, do_setitimer, dhcpcd/5128
 # expires at 604918992928181 nsecs [in 604639200821123 nsecs]
 #6: <ffff81004f98bda8>, hrtimer_wakeup, S:01, do_nanosleep, dhcpcd/5128
 # expires at 604918992950531 nsecs [in 604639200843473 nsecs]


Tick Device: mode:     0
Clock Event Device: pit
 max_delta_ns:   27461866
 min_delta_ns:   12571
 mult:           5124677
 shift:          32
 mode:           2
 next_event:     9223372036854775807 nsecs
 set_next_event: pit_next_event
 set_mode:       init_pit_timer
 event_handler:  tick_handle_periodic_broadcast
tick_broadcast_mask: 00000003


Tick Device: mode:     0
Clock Event Device: lapic
 max_delta_ns:   0
 min_delta_ns:   0
 mult:           0
 shift:          32
 mode:           1
 next_event:     0 nsecs
 set_next_event: lapic_next_event
 set_mode:       lapic_timer_setup
 event_handler:  tick_handle_periodic

Tick Device: mode:     0
Clock Event Device: lapic
 max_delta_ns:   0
 min_delta_ns:   0
 mult:           0
 shift:          32
 mode:           1
 next_event:     0 nsecs
 set_next_event: lapic_next_event
 set_mode:       lapic_timer_setup
 event_handler:  tick_handle_periodic

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Thomas Gleixner]

Rafael,

On Tue, 2007-09-25 at 23:28 +0200, Rafael J. Wysocki wrote:
> > I'm a bit confused by your earlier confirmation, that mainline w/o the
> > -hrt patches boots fine, when you add "apicmaintimer" to the kernel
> > command line. "apicmaintimer" stops the PIT like we do in -hrt and we
> > just use the local APIC timer for everything. Can you please retest and
> > confirm that this is correct ?
> 
> No, it's not.  The mainline _usually_ doesn't boot with "apicmaintimer".
> 
> It seems to me that _sometimes_ the CPU just doesn't enter this C1E state
> and then everything goes fine ...

I'm relieved. I really started to go nuts on this contradicting
patterns.

Your box seems to be worse than the VAIO, it has some random surprise
generator built in :)

> > Is the 32 bit kernel working on that box ?
> 
> Can't tell, I have only 64-bit userland here.

Should be fine. The check is there since late 2.6.21-rc. I really could
kick my own ass that I did not remember the nx6325 wreckage in the
2.6.21-rc time frame. Sigh, way too much broken hardware out there to
keep track of it.

> > Thanks for your patience.
> 
> Well, I'm only making sure that future kernels will run on my box. ;-)

Nothing wrong with that. Thanks again for your help,

	tglx

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

[-- Attachment #1: Type: text/plain, Size: 5497 bytes --]

Thomas,

On Tuesday, 25 September 2007 23:24, Thomas Gleixner wrote:
> Rafael,
> 
> On Tue, 2007-09-25 at 23:28 +0200, Rafael J. Wysocki wrote:
> > > I'm a bit confused by your earlier confirmation, that mainline w/o the
> > > -hrt patches boots fine, when you add "apicmaintimer" to the kernel
> > > command line. "apicmaintimer" stops the PIT like we do in -hrt and we
> > > just use the local APIC timer for everything. Can you please retest and
> > > confirm that this is correct ?
> > 
> > No, it's not.  The mainline _usually_ doesn't boot with "apicmaintimer".
> > 
> > It seems to me that _sometimes_ the CPU just doesn't enter this C1E state
> > and then everything goes fine ...
> 
> I'm relieved. I really started to go nuts on this contradicting
> patterns.
> 
> Your box seems to be worse than the VAIO, it has some random surprise
> generator built in :)
> 
> > > Is the 32 bit kernel working on that box ?
> > 
> > Can't tell, I have only 64-bit userland here.
> 
> Should be fine. The check is there since late 2.6.21-rc. I really could
> kick my own ass that I did not remember the nx6325 wreckage in the
> 2.6.21-rc time frame. Sigh, way too much broken hardware out there to
> keep track of it.
> 
> > > Thanks for your patience.
> > 
> > Well, I'm only making sure that future kernels will run on my box. ;-)
> 
> Nothing wrong with that. Thanks again for your help,

There still are some oddities.

First, with the "x86-64: Disable local APIC timer use on AMD systems with C1E"
patch and my collection of suspend patches applied, the box doesn't boot
(the suspend patches don't even thouch the boot code, so they should be
irrelevant here).  However, it boots if patch-2.6.23-rc7-hrt1.patch (adjusted
for 2.6.23-rc8) is applied in addition.  Is this expected?

Next, on 2.6.23-rc8 with the patches from:

http://www.sisk.pl/kernel/hibernation_and_suspend/2.6.23-rc8/patches/

plus the "x86-64: Disable local APIC timer use on AMD systems with C1E" patch
and patch-2.6.23-rc7-hrt1.patch (adjusted for 2.6.23-rc8), hibernation doesn't
work correctly.  Although the box hibernates and restores, there is a temporary
"hang" during the "resume hardware" sequence, after which the "lock" led starts
to blink (and remains in this state) and something like this appears in dmesg:

Extended CMOS year: 2000
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3990.36 BogoMIPS (lpj=7980735)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Unable to handle kernel paging request at ffffffff806c64d4 RIP: 
 [<ffffffff802104cb>] identify_cpu+0x2ac/0x5a1
PGD 203067 PUD 207063 PMD 37fb4163 PTE 6c6000
Oops: 0002 [1] SMP 
CPU 1 
Modules linked in: ip6t_LOG nf_conntrack_ipv6 xt_pkttype ipt_LOG xt_limit cpufreq_conservative cpufreq_ondemand cpufreq_userspace cpufreq_powersave powernow_k8 freq_table thermal processor fan snd_pcm_oss button snd_mixer_oss snd_seq battery snd_seq_device ac ip6t_REJECT xt_tcpudp ipt_REJECT xt_state iptable_mangle iptable_nat nf_nat iptable_filter ip6table_mangle nf_conntrack_ipv4 nf_conntrack nfnetlink ip_tables ip6table_filter ip6_tables x_tables ipv6 loop dm_mod rfcomm hidp l2cap usbhid ff_memless psmouse hci_usb bluetooth pcmcia tg3 ohci_hcd snd_hda_intel ehci_hcd yenta_socket rsrc_nonstatic ide_cd ohci1394 k8temp i2c_piix4 pcmcia_core sdhci shpchp snd_pcm usbcore hwmon i2c_core rtc_cmos rtc_core rtc_lib ieee1394 mmc_core tifm_7xx1 tifm_core pci_hotplug snd_timer cdrom snd firmware_class ieee80211softmac ieee80211 ieee80211_crypt soundcore snd_page_alloc ext3 jbd edd atiixp ide_disk ide_core sg
Pid: 0, comm: swapper Not tainted 2.6.23-rc8-rjw #6
RIP: 0010:[<ffffffff802104cb>]  [<ffffffff802104cb>] identify_cpu+0x2ac/0x5a1
RSP: 0018:ffff810037abdea8  EFLAGS: 00010006
RAX: 0000000014008015 RBX: 0000000001020800 RCX: 00000000c0010055
RDX: 0000000000000000 RSI: 0000000000040000 RDI: 0000000000000001
RBP: ffff810037abded8 R08: 0000000000000000 R09: ffffffff80444ad0
R10: ffffffff8070c860 R11: 0000000000000001 R12: ffffffff805920c0
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
FS:  0000000000000000(0000) GS:ffff810037ac3e88(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: ffffffff806c64d4 CR3: 0000000000201000 CR4: 00000000000006a0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 0, threadinfo ffff810037abc000, task ffff810037a8f800)
Stack:  0000000f4e5a1540 000000000000059f 0000000000000001 ffffffff805920c0
 0000000000000001 0000000000000000 ffff810037abdef8 ffffffff8021acaa
 000000000000059f 0000000000000000 ffff810037abdf48 ffffffff8021b380
Call Trace:
 [<ffffffff8021acaa>] smp_callin+0xc8/0xde
 [<ffffffff8021b380>] start_secondary+0x1b/0x2e8


Code: c7 05 ff 5f 4b 00 01 00 00 00 e9 4f 01 00 00 4c 89 e7 e8 27 
RIP  [<ffffffff802104cb>] identify_cpu+0x2ac/0x5a1
 RSP <ffff810037abdea8>
CR2: ffffffff806c64d4
Kernel panic - not syncing: Attempted to kill the idle task!
Stuck ??
Inquiring remote APIC #1...
... APIC #1 ID: 01000000
... APIC #1 VERSION: 80050010
... APIC #1 SPIV: 000000ff
Error taking CPU1 up: -5
atkbd.c: Spurious ACK on isa0060/serio0. Some program might be trying access hardware directly.

Looks like the CPU hotplug is busted, or what?

Full dmesg attached.

Greetings,
Rafael

[-- Attachment #2: 2.6.23-rc8-rjw.log --]
[-- Type: text/x-log, Size: 51416 bytes --]

Linux version 2.6.23-rc8-rjw (rafael@albercik) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #6 SMP Wed Sep 26 00:51:10 CEST 2007
Command line: root=/dev/sda3 vga=792 resume=/dev/sda1 no_console_suspend
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000077fd0000 (usable)
 BIOS-e820: 0000000077fd0000 - 0000000077fe5600 (reserved)
 BIOS-e820: 0000000077fe5600 - 0000000077ff8000 (ACPI NVS)
 BIOS-e820: 0000000077ff8000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved)
 BIOS-e820: 00000000ffbc0000 - 00000000ffcc0000 (reserved)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 491472) 1 entries of 256 used
end_pfn_map = 1048576
DMI 2.4 present.
ACPI: RSDP 000F7D30, 0024 (r2 HP    )
ACPI: XSDT 77FE57B4, 0054 (r1 HP     0944      6070620 HP          1)
ACPI: FACP 77FE5684, 00F4 (r4 HP     0944            3 HP          1)
ACPI: DSDT 77FE58DC, EE7A (r1 HP        SB400    10000 MSFT  100000E)
ACPI: FACS 77FF7E80, 0040
ACPI: APIC 77FE5808, 0062 (r1 HP     0944            1 HP          1)
ACPI: MCFG 77FE586C, 003C (r1 HP     0944            1 HP          1)
ACPI: TCPA 77FE58A8, 0032 (r2 HP     0944            1 HP          1)
ACPI: SSDT 77FF4756, 0059 (r1 HP       HPQNLP        1 MSFT  100000E)
ACPI: SSDT 77FF47AF, 0206 (r1 HP     PSSTBLID        1 HP          1)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 491472) 1 entries of 256 used
No mptable found.
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0:        0 ->      159
    0:      256 ->   491472
On node 0 totalpages: 491375
  DMA zone: 56 pages used for memmap
  DMA zone: 1444 pages reserved
  DMA zone: 2499 pages, LIFO batch:0
  DMA32 zone: 6663 pages used for memmap
  DMA32 zone: 480713 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 47512 bytes of per cpu data
Built 1 zonelists in Zone order.  Total pages: 483212
Kernel command line: root=/dev/sda3 vga=792 resume=/dev/sda1 no_console_suspend
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
TSC calibrated against PM_TIMER
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 1994.990 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ 108000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 1924064k/1965888k available (2201k kernel code, 41152k reserved, 1436k data, 248k init)
Calibrating delay using timer specific routine.. 3994.23 BogoMIPS (lpj=7988468)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Parsing all Control Methods:
Table [DSDT](id 0001) - 1153 Objects with 113 Devices 337 Methods 33 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 2 Objects with 0 Devices 2 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0003) - 8 Objects with 0 Devices 0 Methods 0 Regions
 tbxface-0598 [00] tb_load_namespace     : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable                : Transition to ACPI mode successful
..MP-BIOS bug: 8254 timer not connected to IO-APIC
Disabling APIC timer
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3990.40 BogoMIPS (lpj=7980803)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Turion(tm) 64 X2 Mobile Technology TL-60 stepping 02
Brought up 2 CPUs
Time:  0:36:29  Date: 09/26/07
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: No mmconfig possible on device 00:18
evgpeblk-0956 [00] ev_create_gpe_block   : GPE 00 to 1F [_GPE] 4 regs on int 0x15
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 3 Wake, Enabled 11 Runtime GPEs in this block
ACPI: EC: Look up EC in DSDT
ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
Completing Region/Field/Buffer/Package initialization:................................................................................................................................................................
Initialized 29/33 Regions 0/0 Fields 63/64 Buffers 68/78 Packages (1172 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:.......
Executed 7 _INI methods requiring 2 _STA executions (examined 120 objects)
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [C074] (0000:00)
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.C074._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C074.C075._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C074.C0DF._PRT]
ACPI: PCI Interrupt Link [C125] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C126] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C127] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C128] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C129] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C12A] (IRQs 9) *0, disabled.
ACPI: PCI Interrupt Link [C12B] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C12C] (IRQs *10 11)
ACPI: Power Resource [C223] (off)
ACPI: Power Resource [C1FE] (off)
ACPI: Power Resource [C217] (on)
ACPI: Power Resource [C34B] (off)
ACPI: Power Resource [C34C] (off)
ACPI: Power Resource [C34D] (off)
ACPI: Power Resource [C34E] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Cannot allocate resource region 0 of device 0000:00:14.2
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
ACPI: RTC can wake from S4
pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:00: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:00: iomem range 0x100000-0x77ffffff could not be reserved
pnp: 00:0a: ioport range 0x40b-0x40b has been reserved
pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0a: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:0a: iomem range 0xffb00000-0xffbfffff could not be reserved
pnp: 00:0a: iomem range 0xfff00000-0xffffffff could not be reserved
pnp: 00:0b: ioport range 0x8000-0x802f has been reserved
pnp: 00:0b: ioport range 0x8100-0x811f has been reserved
pnp: 00:0b: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:0c: iomem range 0xcf000-0xcffff has been reserved
pnp: 00:0c: iomem range 0x78000000-0x7fffffff could not be reserved
pnp: 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: 6000-6fff
  MEM window: d4300000-d43fffff
  PREFETCH window: c0000000-c7ffffff
PCI: Bridge: 0000:00:04.0
  IO window: 4000-5fff
  MEM window: d0000000-d3ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:05.0
  IO window: 2000-3fff
  MEM window: cc000000-cfffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
  IO window: disabled.
  MEM window: c8000000-c80fffff
  PREFETCH window: disabled.
PCI: Bus 3, cardbus bridge: 0000:02:04.0
  IO window: 00001000-000010ff
  IO window: 00001400-000014ff
  PREFETCH window: 88000000-8bffffff
  MEM window: 90000000-93ffffff
PCI: Bridge: 0000:00:14.4
  IO window: 1000-1fff
  MEM window: d4000000-d42fffff
  PREFETCH window: 88000000-8bffffff
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:05.0 to 64
PCI: Setting latency timer of device 0000:00:06.0 to 64
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 20 (level, low) -> IRQ 20
NET: Registered protocol family 2
Time: acpi_pm clocksource has been installed.
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 5222k freed
audit: initializing netlink socket (disabled)
audit(1190766990.012:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: MSI quirk detected. MSI deactivated.
Boot video device is 0000:01:05.0
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie01]
Allocate Port Service[0000:00:04.0:pcie03]
PCI: Setting latency timer of device 0000:00:05.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:05.0:pcie00]
Allocate Port Service[0000:00:05.0:pcie01]
Allocate Port Service[0000:00:05.0:pcie03]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
Allocate Port Service[0000:00:06.0:pcie01]
Allocate Port Service[0000:00:06.0:pcie03]
AER service couldn't init device 0000:00:04.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:05.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:06.0:pcie01 - no _OSC support
vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20010100000, using 4608k, total 16384k
vesafb: mode is 1024x768x24, linelength=3072, pages=6
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize
sata_sil 0000:00:12.0: version 2.3
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 16 (level, low) -> IRQ 16
scsi0 : sata_sil
scsi1 : sata_sil
ata1: SATA max UDMA/100 cmd 0xffffc2000002a080 ctl 0xffffc2000002a08a bmdma 0xffffc2000002a000 irq 16
ata2: SATA max UDMA/100 cmd 0xffffc2000002a0c0 ctl 0xffffc2000002a0ca bmdma 0xffffc2000002a008 irq 16
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: FUJITSU MHV2080BH, 892C, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA48 
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHV2080B 892C PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 0:0:0:0: [sda] Attached SCSI disk
PNP: PS/2 Controller [PNP0303:C214,PNP0f13:C215] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
NET: Registered protocol family 1
swsusp: Resume From Partition /dev/sda1
PM: Checking swsusp image.
PM: Resume from disk failed.
  Magic number: 7:549:608
Freeing unused kernel memory: 248k freed
Write protecting the kernel read-only data: 1060k
sd 0:0:0:0: Attached scsi generic sg0 type 0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
ATIIXP: chipset revision 128
ATIIXP: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x7040-0x7047, BIOS settings: hda:DMA, hdb:pio
ATIIXP: simplex device: DMA disabled
ide1: ATIIXP Bus-Master DMA disabled (BIOS)
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GMA-4082N, ATAPI CD/DVD-ROM drive
hda: selected mode 0x22
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
swsusp: Marking nosave pages: 000000000009f000 - 0000000000100000
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
Attempting manual resume
swsusp: Resume From Partition 8:1
PM: Checking swsusp image.
PM: Resume from disk failed.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
Floppy drive(s): fd0 is 1.44M
bcm43xx driver
ACPI: PCI Interrupt 0000:30:00.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:30:00.0 to 64
bcm43xx: Chip ID 0x4311, rev 0x1
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0x11, vendor 0x4243
bcm43xx: Core 1: ID 0x812, rev 0xa, vendor 0x4243
bcm43xx: Core 2: ID 0x817, rev 0x3, vendor 0x4243
bcm43xx: Core 3: ID 0x820, rev 0x1, vendor 0x4243
bcm43xx: PHY connected
bcm43xx: Detected PHY: Analog: 4, Type 2, Revision 8
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: PCI Interrupt 0000:02:04.2[A] -> GSI 20 (level, low) -> IRQ 20
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc_cmos: probe of 00:07 failed with error -16
usbcore: registered new interface driver usbfs
net eth1: device_rename: sysfs_create_symlink failed (-17)
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:02:04.3 [104c:803c] (rev 0)
ACPI: PCI Interrupt 0000:02:04.3[A] -> GSI 20 (level, low) -> IRQ 20
mmc0: SDHCI at 0xd4019000 irq 20 PIO
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
ACPI: PCI Interrupt 0000:02:04.1[A] -> GSI 20 (level, low) -> IRQ 20
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20]  MMIO=[d4011000-d40117ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
Yenta: CardBus bridge found at 0000:02:04.0 [103c:30b0]
Yenta: Enabling burst memory read transactions
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x01a11002, devctl 0x64
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: EHCI Host Controller
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/inode.c: creating file 'devices'
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/inode.c: creating file '001'
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.2: reset hcs_params 0x2408 dbg=0 cc=2 pcc=4 ordered !ppc ports=8
ehci_hcd 0000:00:13.2: reset hcc_params a012 thresh 1 uframes 256/512/1024
ehci_hcd 0000:00:13.2: MWI active
ehci_hcd 0000:00:13.2: irq 19, io mem 0xd4403000
ehci_hcd 0000:00:13.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:13.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.23-rc8-rjw ehci_hcd
usb usb1: SerialNumber: 0000:00:13.2
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: trying to enable port power on non-switchable hub
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 80 td 96
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/inode.c: creating file '001'
ehci_hcd 0000:00:13.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
Yenta: ISA IRQ mask 0x0eb8, PCI irq 20
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
pcmcia: parent PCI bridge I/O window: 0x1000 - 0x1fff
pcmcia: parent PCI bridge Memory window: 0xd4000000 - 0xd42fffff
pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x8bffffff
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.0: OHCI Host Controller
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
ohci_hcd 0000:00:13.0: created debug files
ohci_hcd 0000:00:13.0: irq 19, io mem 0xd4401000
ehci_hcd 0000:00:13.2: port 2 full speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 2 status 003801 POWER OWNER sig=j CONNECT
hub 1-0:1.0: port 2 not reset yet, waiting 50ms
ohci_hcd 0000:00:13.0: OHCI controller state
ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:13.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:13.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:13.0: intrenable 0x8000005a MIE RHSC UE RD WDH
ohci_hcd 0000:00:13.0: hcca frame #0005
ohci_hcd 0000:00:13.0: roothub.a 02000204 POTPGT=2 NPS NDP=4(4)
ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00010100 CSC PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [3] 0x00000100 PPS
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
ehci_hcd 0000:00:13.2: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
ehci_hcd 0000:00:13.2: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
usb usb2: Manufacturer: Linux 2.6.23-rc8-rjw ohci_hcd
usb usb2: SerialNumber: 0000:00:13.0
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
hub 2-0:1.0: 4 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 4ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: trying to enable port power on non-switchable hub
ehci_hcd 0000:00:13.2: port 3 full speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 3 status 003801 POWER OWNER sig=j CONNECT
hub 1-0:1.0: port 3 not reset yet, waiting 50ms
ehci_hcd 0000:00:13.2: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC
ehci_hcd 0000:00:13.2: GetStatus port 6 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.1: OHCI Host Controller
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/inode.c: creating file '003'
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: created debug files
ohci_hcd 0000:00:13.1: irq 19, io mem 0xd4402000
ohci_hcd 0000:00:13.1: OHCI controller state
ohci_hcd 0000:00:13.1: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:13.1: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:13.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:13.1: intrstatus 0x00000004 SF
ohci_hcd 0000:00:13.1: intrenable 0x8000005a MIE RHSC UE RD WDH
ohci_hcd 0000:00:13.1: hcca frame #0005
ohci_hcd 0000:00:13.1: roothub.a 02000204 POTPGT=2 NPS NDP=4(4)
ohci_hcd 0000:00:13.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:13.1: roothub.status 00008000 DRWE
ohci_hcd 0000:00:13.1: roothub.portstatus [0] 0x00010100 CSC PPS
ohci_hcd 0000:00:13.1: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:13.1: roothub.portstatus [2] 0x00010100 CSC PPS
ohci_hcd 0000:00:13.1: roothub.portstatus [3] 0x00000100 PPS
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.23-rc8-rjw ohci_hcd
usb usb3: SerialNumber: 0000:00:13.1
usb usb3: uevent
usb usb3: usb_probe_device
usb usb3: configuration #1 chosen from 1 choice
hub 1-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501
usb usb3: adding 3-0:1.0 (config #1, interface 0)
ehci_hcd 0000:00:13.2: port 6 low speed --> companion
usb 3-0:1.0: uevent
usb 3-0:1.0: uevent
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: global over-current protection
hub 3-0:1.0: power on to power good time: 4ms
hub 3-0:1.0: local power source is good
hub 3-0:1.0: no over-current condition exists
hub 3-0:1.0: trying to enable port power on non-switchable hub
ehci_hcd 0000:00:13.2: GetStatus port 6 status 003002 POWER OWNER sig=se0 CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0044
ehci_hcd 0000:00:13.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/inode.c: creating file '001'
tg3.c:v3.81 (September 5, 2007)
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 23 (level, low) -> IRQ 23
eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:17:08:2e:2e:f3
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 2 full speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 2 status 003801 POWER OWNER sig=j CONNECT
hub 1-0:1.0: port 2 not reset yet, waiting 50ms
ehci_hcd 0000:00:13.2: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0004
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023f9929613f0c]
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 2-2: new full speed USB device using ohci_hcd and address 2
floppy0: no floppy controllers found
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 2-2: skipped 1 descriptor after interface
usb 2-2: default language 0x0409
usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-2: Product: HP Integrated Module
usb 2-2: Manufacturer: Broadcom Corp
usb 2-2: uevent
usb 2-2: usb_probe_device
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2: adding 2-2:1.1 (config #1, interface 1)
usb 2-2:1.1: uevent
usb 2-2:1.1: uevent
usb 2-2: adding 2-2:1.2 (config #1, interface 2)
usb 2-2:1.2: uevent
usb 2-2:1.2: uevent
usb 2-2: adding 2-2:1.3 (config #1, interface 3)
usb 2-2:1.3: uevent
usb 2-2:1.3: uevent
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/inode.c: creating file '002'
hub 3-0:1.0: state 7 ports 4 chg 0000 evt 000a
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 3-1: new full speed USB device using ohci_hcd and address 2
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
usb 3-1: ep0 maxpacket = 8
usb 3-1: default language 0x0409
usb 3-1: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 3-1: Product: Fingerprint Sensor
usb 3-1: uevent
usb 3-1: usb_probe_device
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: adding 3-1:1.0 (config #1, interface 0)
usb 3-1:1.0: uevent
usb 3-1:1.0: uevent
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00010301 CSC LSDA PPS CCS
hub 3-0:1.0: port 3, status 0301, change 0001, 1.5 Mb/s
Bluetooth: HCI USB driver ver 2.9
hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS
usb 3-3: new low speed USB device using ohci_hcd and address 3
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS
usb 3-3: skipped 1 descriptor after interface
usb 3-3: skipped 1 descriptor after interface
usb 3-3: default language 0x0409
usb 3-3: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-3: Product: USB Receiver
usb 3-3: Manufacturer: Logitech
usb 3-3: uevent
usb 3-3: usb_probe_device
usb 3-3: configuration #1 chosen from 1 choice
usb 3-3: adding 3-3:1.0 (config #1, interface 0)
usb 3-3:1.0: uevent
usb 3-3:1.0: uevent
usb 3-3: adding 3-3:1.1 (config #1, interface 1)
usb 3-3:1.1: uevent
usb 3-3:1.1: uevent
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/inode.c: creating file '003'
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0004
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0004
hub 3-0:1.0: state 7 ports 4 chg 0000 evt 0002
hci_usb 2-2:1.0: usb_probe_interface
hci_usb 2-2:1.0: usb_probe_interface - got id
usb_endpoint usbdev2.2_ep83: ep_device_release called for usbdev2.2_ep83
usb_endpoint usbdev2.2_ep03: ep_device_release called for usbdev2.2_ep03
hci_usb 2-2:1.2: usb_probe_interface
hci_usb 2-2:1.2: usb_probe_interface - got id
hci_usb 2-2:1.3: usb_probe_interface
hci_usb 2-2:1.3: usb_probe_interface - got id
usbcore: registered new interface driver hci_usb
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04793/0x300000
serio: Synaptics pass-through port at isa0060/serio4/input0
input: SynPS/2 Synaptics TouchPad as /class/input/input2
usbcore: registered new interface driver hiddev
usbhid 3-3:1.0: usb_probe_interface
usbhid 3-3:1.0: usb_probe_interface - got id
input: Logitech USB Receiver as /class/input/input3
input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-3
usbhid 3-3:1.1: usb_probe_interface
usbhid 3-3:1.1: usb_probe_interface - got id
input: Logitech USB Receiver as /class/input/input4
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/file.c: looking for a minor, starting at 96
input,hiddev96: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:13.1-3
usbcore: registered new interface driver usbhid
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
ehci_hcd 0000:00:13.2: suspend root hub
loop: module loaded
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
Adding 1052216k swap on /dev/sda1.  Priority:-1 extents:1 across:1052216k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ACPI: AC Adapter [C1BD] (on-line)
ACPI: Battery Slot [C1BF] (battery present)
ACPI: Battery Slot [C1BE] (battery absent)
input: Power Button (FF) as /class/input/input5
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [C25A]
input: Lid Switch as /class/input/input7
ACPI: Lid Switch [C25B]
ACPI: Transitioning device [C34F] to D3
ACPI: Transitioning device [C34F] to D3
ACPI: Fan [C34F] (off)
ACPI: Transitioning device [C350] to D3
ACPI: Transitioning device [C350] to D3
ACPI: Fan [C350] (off)
ACPI: Transitioning device [C351] to D3
ACPI: Transitioning device [C351] to D3
ACPI: Fan [C351] (off)
ACPI: Transitioning device [C352] to D3
ACPI: Transitioning device [C352] to D3
ACPI: Fan [C352] (off)
ACPI: Processor [C000] (supports 8 throttling states)
ACPI: Processor [C001] (supports 8 throttling states)
ACPI: Thermal Zone [TZ1] (59 C)
ACPI: Thermal Zone [TZ2] (50 C)
ACPI: Thermal Zone [TZ3] (29 C)
powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-60 processors (2 cpu cores) (version 2.00.00)
powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x13
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x15
powernow-k8:    2 : fid 0x8 (1600 MHz), vid 0x17
powernow-k8:    3 : fid 0x0 (800 MHz), vid 0x1e
powernow-k8: ph2 null fid transition 0xc
mtrr: no more MTRRs available
hda-intel: Invalid position buffer, using LPIB read method instead.
ACPI: PCI interrupt for device 0000:30:00.0 disabled
swsusp: Marking nosave pages: 000000000009f000 - 0000000000100000
swsusp: Basic memory bitmaps created
Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.00 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
Shrinking memory...  \b-\b\\bdone (13372 pages freed)
Freed 53488 kbytes in 0.38 seconds (140.75 MB/s)
hub 3-0:1.0: hub_suspend
usb usb3: bus suspend
ohci_hcd 0000:00:13.1: suspend root hub
hub 2-0:1.0: hub_suspend
usb usb2: bus suspend
ohci_hcd 0000:00:13.0: suspend root hub
sd 0:0:0:0: [sda] Synchronizing SCSI cache
ACPI handle has no context!
ACPI handle has no context!
ACPI: PCI interrupt for device 0000:02:04.3 disabled
ACPI handle has no context!
ACPI handle has no context!
ACPI: PCI interrupt for device 0000:02:04.2 disabled
ACPI handle has no context!
ACPI handle has no context!
ACPI: PCI interrupt for device 0000:00:14.2 disabled
ACPI: PCI interrupt for device 0000:00:13.2 disabled
ehci_hcd 0000:00:13.2: --> PCI D3
ACPI: PCI interrupt for device 0000:00:13.1 disabled
ohci_hcd 0000:00:13.1: --> PCI D0/legacy
ACPI: PCI interrupt for device 0000:00:13.0 disabled
ohci_hcd 0000:00:13.0: --> PCI D0/legacy
ACPI: PCI interrupt for device 0000:00:12.0 disabled
ACPI: Transitioning device [C351] to D0
ACPI: Transitioning device [C351] to D0
ACPI: Transitioning device [C350] to D0
ACPI: Transitioning device [C350] to D0
ACPI: Transitioning device [C34F] to D0
ACPI: Transitioning device [C34F] to D0
Disabling non-boot CPUs ...
Cannot set affinity for irq 0
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU1 is down
Extended CMOS year: 2000
swsusp: critical section: 
swsusp: Need to copy 150754 pages
swsusp: Normal pages needed: 150754 + 1024 + 36, available pages: 340619
evxfevnt-0079 [00] enable                : System is already in ACPI mode
Extended CMOS year: 2000
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3990.36 BogoMIPS (lpj=7980735)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Unable to handle kernel paging request at ffffffff806c64d4 RIP: 
 [<ffffffff802104cb>] identify_cpu+0x2ac/0x5a1
PGD 203067 PUD 207063 PMD 37fb4163 PTE 6c6000
Oops: 0002 [1] SMP 
CPU 1 
Modules linked in: ip6t_LOG nf_conntrack_ipv6 xt_pkttype ipt_LOG xt_limit cpufreq_conservative cpufreq_ondemand cpufreq_userspace cpufreq_powersave powernow_k8 freq_table thermal processor fan snd_pcm_oss button snd_mixer_oss snd_seq battery snd_seq_device ac ip6t_REJECT xt_tcpudp ipt_REJECT xt_state iptable_mangle iptable_nat nf_nat iptable_filter ip6table_mangle nf_conntrack_ipv4 nf_conntrack nfnetlink ip_tables ip6table_filter ip6_tables x_tables ipv6 loop dm_mod rfcomm hidp l2cap usbhid ff_memless psmouse hci_usb bluetooth pcmcia tg3 ohci_hcd snd_hda_intel ehci_hcd yenta_socket rsrc_nonstatic ide_cd ohci1394 k8temp i2c_piix4 pcmcia_core sdhci shpchp snd_pcm usbcore hwmon i2c_core rtc_cmos rtc_core rtc_lib ieee1394 mmc_core tifm_7xx1 tifm_core pci_hotplug snd_timer cdrom snd firmware_class ieee80211softmac ieee80211 ieee80211_crypt soundcore snd_page_alloc ext3 jbd edd atiixp ide_disk ide_core sg
Pid: 0, comm: swapper Not tainted 2.6.23-rc8-rjw #6
RIP: 0010:[<ffffffff802104cb>]  [<ffffffff802104cb>] identify_cpu+0x2ac/0x5a1
RSP: 0018:ffff810037abdea8  EFLAGS: 00010006
RAX: 0000000014008015 RBX: 0000000001020800 RCX: 00000000c0010055
RDX: 0000000000000000 RSI: 0000000000040000 RDI: 0000000000000001
RBP: ffff810037abded8 R08: 0000000000000000 R09: ffffffff80444ad0
R10: ffffffff8070c860 R11: 0000000000000001 R12: ffffffff805920c0
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
FS:  0000000000000000(0000) GS:ffff810037ac3e88(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: ffffffff806c64d4 CR3: 0000000000201000 CR4: 00000000000006a0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 0, threadinfo ffff810037abc000, task ffff810037a8f800)
Stack:  0000000f4e5a1540 000000000000059f 0000000000000001 ffffffff805920c0
 0000000000000001 0000000000000000 ffff810037abdef8 ffffffff8021acaa
 000000000000059f 0000000000000000 ffff810037abdf48 ffffffff8021b380
Call Trace:
 [<ffffffff8021acaa>] smp_callin+0xc8/0xde
 [<ffffffff8021b380>] start_secondary+0x1b/0x2e8


Code: c7 05 ff 5f 4b 00 01 00 00 00 e9 4f 01 00 00 4c 89 e7 e8 27 
RIP  [<ffffffff802104cb>] identify_cpu+0x2ac/0x5a1
 RSP <ffff810037abdea8>
CR2: ffffffff806c64d4
Kernel panic - not syncing: Attempted to kill the idle task!
Stuck ??
Inquiring remote APIC #1...
... APIC #1 ID: 01000000
... APIC #1 VERSION: 80050010
... APIC #1 SPIV: 000000ff
Error taking CPU1 up: -5
atkbd.c: Spurious ACK on isa0060/serio0. Some program might be trying access hardware directly.
ACPI: Transitioning device [C34F] to D3
ACPI: Transitioning device [C34F] to D3
ACPI: Transitioning device [C350] to D3
ACPI: Transitioning device [C350] to D3
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:05.0 to 64
PCI: Setting latency timer of device 0000:00:06.0 to 64
PM: Writing back config space on device 0000:00:12.0 at offset 1 (was 2b00003, writing 2b00007)
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:13.0: PCI legacy resume
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.1: PCI legacy resume
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: PCI D0, from previous PCI D3
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
PM: Writing back config space on device 0000:00:13.2 at offset 1 (was 2b00007, writing 2b00017)
ehci_hcd 0000:00:13.2: lost power, restarting
usb usb1: root hub lost power or was reset
ehci_hcd 0000:00:13.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:13.2: MWI active
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
PM: Writing back config space on device 0000:00:14.2 at offset f (was 10a, writing a)
PM: Writing back config space on device 0000:00:14.2 at offset 1 (was 4100006, writing 4100002)
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
PM: Writing back config space on device 0000:00:14.4 at offset 6 (was 40030200, writing 40060200)
PM: Writing back config space on device 0000:30:00.0 at offset 1 (was 100007, writing 100003)
PM: Writing back config space on device 0000:02:04.0 at offset f (was 3c4010a, writing 5c0010a)
PM: Writing back config space on device 0000:02:04.0 at offset 3 (was 824010, writing 82a810)
ata2: SATA link down (SStatus 0 SControl 300)
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20]  MMIO=[d4011000-d40117ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:02:04.2[A] -> GSI 20 (level, low) -> IRQ 20
ACPI: PCI Interrupt 0000:02:04.3[A] -> GSI 20 (level, low) -> IRQ 20
sd 0:0:0:0: [sda] Starting disk
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/100
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
hda: selected mode 0x22
usb usb1: usb resume
ehci_hcd 0000:00:13.2: resume root hub after power loss
hub 1-0:1.0: trying to enable port power on non-switchable hub
usb usb2: usb resume
ohci_hcd 0000:00:13.0: BIOS/SMM active, control 008
ohci_hcd 0000:00:13.0: OHCI controller state
ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:13.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:13.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:13.0: intrenable 0x8000005a MIE RHSC UE RD WDH
ohci_hcd 0000:00:13.0: hcca frame #00c8
ohci_hcd 0000:00:13.0: roothub.a 02000204 POTPGT=2 NPS NDP=4(4)
ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00010100 CSC PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:13.0: restart complete
usb usb2: root hub lost power or was reset
hub 2-0:1.0: trying to enable port power on non-switchable hub
hub 2-0:1.0: logical disconnect on port 2
usb usb3: usb resume
ohci_hcd 0000:00:13.1: BIOS/SMM active, control 008
ohci_hcd 0000:00:13.1: OHCI controller state
ohci_hcd 0000:00:13.1: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:13.1: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:13.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:13.1: intrstatus 0x00000004 SF
ohci_hcd 0000:00:13.1: intrenable 0x8000005a MIE RHSC UE RD WDH
ohci_hcd 0000:00:13.1: hcca frame #00a1
ohci_hcd 0000:00:13.1: roothub.a 02000204 POTPGT=2 NPS NDP=4(4)
ohci_hcd 0000:00:13.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:13.1: roothub.status 00008000 DRWE
ohci_hcd 0000:00:13.1: roothub.portstatus [0] 0x00010100 CSC PPS
ohci_hcd 0000:00:13.1: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:13.1: roothub.portstatus [2] 0x00010100 CSC PPS
ohci_hcd 0000:00:13.1: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:13.1: restart complete
usb usb3: root hub lost power or was reset
hub 3-0:1.0: trying to enable port power on non-switchable hub
hub 3-0:1.0: logical disconnect on port 1
hub 3-0:1.0: logical disconnect on port 3
Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 8 chg 0000 evt 004c
ehci_hcd 0000:00:13.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
done.
swsusp: Basic memory bitmaps freed
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 2 full speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 2 status 003801 POWER OWNER sig=j CONNECT
hub 1-0:1.0: port 2 not reset yet, waiting 50ms
ehci_hcd 0000:00:13.2: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
ehci_hcd 0000:00:13.2: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 3 full speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 3 status 003801 POWER OWNER sig=j CONNECT
hub 1-0:1.0: port 3 not reset yet, waiting 50ms
ehci_hcd 0000:00:13.2: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC
ehci_hcd 0000:00:13.2: GetStatus port 6 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 6 low speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 6 status 003002 POWER OWNER sig=se0 CSC
hub 2-0:1.0: state 7 ports 4 chg 0004 evt 0004
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
usb 2-2: USB disconnect, address 2
usb 2-2: unregistering device
usb 2-2: usb_disable_device nuking all URBs
usb 2-2: unregistering interface 2-2:1.0
usb_endpoint usbdev2.2_ep81: ep_device_release called for usbdev2.2_ep81
usb_endpoint usbdev2.2_ep82: ep_device_release called for usbdev2.2_ep82
usb_endpoint usbdev2.2_ep02: ep_device_release called for usbdev2.2_ep02
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2: unregistering interface 2-2:1.1
usb_endpoint usbdev2.2_ep83: ep_device_release called for usbdev2.2_ep83
usb_endpoint usbdev2.2_ep03: ep_device_release called for usbdev2.2_ep03
usb 2-2:1.1: uevent
usb 2-2:1.1: uevent
usb 2-2: unregistering interface 2-2:1.2
usb_endpoint usbdev2.2_ep84: ep_device_release called for usbdev2.2_ep84
usb_endpoint usbdev2.2_ep04: ep_device_release called for usbdev2.2_ep04
usb 2-2:1.2: uevent
usb 2-2:1.2: uevent
usb 2-2: unregistering interface 2-2:1.3
usb 2-2:1.3: uevent
usb 2-2:1.3: uevent
usb_endpoint usbdev2.2_ep00: ep_device_release called for usbdev2.2_ep00
usb 2-2: uevent
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 2-2: new full speed USB device using ohci_hcd and address 3
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 2-2: skipped 1 descriptor after interface
usb 2-2: default language 0x0409
usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-2: Product: HP Integrated Module
usb 2-2: Manufacturer: Broadcom Corp
usb 2-2: uevent
usb 2-2: usb_probe_device
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
hci_usb 2-2:1.0: usb_probe_interface
hci_usb 2-2:1.0: usb_probe_interface - got id
usb 2-2: adding 2-2:1.1 (config #1, interface 1)
usb 2-2:1.1: uevent
usb 2-2:1.1: uevent
usb 2-2: adding 2-2:1.2 (config #1, interface 2)
usb 2-2:1.2: uevent
usb 2-2:1.2: uevent
hci_usb 2-2:1.2: usb_probe_interface
hci_usb 2-2:1.2: usb_probe_interface - got id
usb 2-2: adding 2-2:1.3 (config #1, interface 3)
usb 2-2:1.3: uevent
usb 2-2:1.3: uevent
hci_usb 2-2:1.3: usb_probe_interface
hci_usb 2-2:1.3: usb_probe_interface - got id
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/inode.c: creating file '003'
hub 3-0:1.0: state 7 ports 4 chg 000a evt 000a
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
usb 3-1: USB disconnect, address 2
usb 3-1: unregistering device
usb 3-1: usb_disable_device nuking all URBs
usb 3-1: unregistering interface 3-1:1.0
usb_endpoint usbdev3.2_ep81: ep_device_release called for usbdev3.2_ep81
usb_endpoint usbdev3.2_ep02: ep_device_release called for usbdev3.2_ep02
usb 3-1:1.0: uevent
usb 3-1:1.0: uevent
usb_endpoint usbdev3.2_ep00: ep_device_release called for usbdev3.2_ep00
usb 3-1: uevent
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 3-1: new full speed USB device using ohci_hcd and address 4
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 3-1: ep0 maxpacket = 8
usb 3-1: default language 0x0409
usb 3-1: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 3-1: Product: Fingerprint Sensor
usb 3-1: uevent
usb 3-1: usb_probe_device
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: adding 3-1:1.0 (config #1, interface 0)
usb 3-1:1.0: uevent
usb 3-1:1.0: uevent
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/inode.c: creating file '004'
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00010301 CSC LSDA PPS CCS
hub 3-0:1.0: port 3, status 0301, change 0001, 1.5 Mb/s
usb 3-3: USB disconnect, address 3
usb 3-3: unregistering device
usb 3-3: usb_disable_device nuking all URBs
usb 3-3: unregistering interface 3-3:1.0
usb_endpoint usbdev3.3_ep81: ep_device_release called for usbdev3.3_ep81
usb 3-3:1.0: uevent
usb 3-3:1.0: uevent
usb 3-3: unregistering interface 3-3:1.1
usb_endpoint usbdev3.3_ep82: ep_device_release called for usbdev3.3_ep82
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/file.c: removing 96 minor
usb 3-3:1.1: uevent
usb 3-3:1.1: uevent
usb_endpoint usbdev3.3_ep00: ep_device_release called for usbdev3.3_ep00
usb 3-3: uevent
hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS
usb 3-3: new low speed USB device using ohci_hcd and address 5
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS
usb 3-3: skipped 1 descriptor after interface
usb 3-3: skipped 1 descriptor after interface
usb 3-3: default language 0x0409
usb 3-3: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-3: Product: USB Receiver
usb 3-3: Manufacturer: Logitech
usb 3-3: uevent
usb 3-3: usb_probe_device
usb 3-3: configuration #1 chosen from 1 choice
usb 3-3: adding 3-3:1.0 (config #1, interface 0)
usb 3-3:1.0: uevent
usb 3-3:1.0: uevent
usbhid 3-3:1.0: usb_probe_interface
usbhid 3-3:1.0: usb_probe_interface - got id
input: Logitech USB Receiver as /class/input/input8
input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-3
usb 3-3: adding 3-3:1.1 (config #1, interface 1)
usb 3-3:1.1: uevent
usb 3-3:1.1: uevent
usbhid 3-3:1.1: usb_probe_interface
usbhid 3-3:1.1: usb_probe_interface - got id
input: Logitech USB Receiver as /class/input/input9
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/file.c: looking for a minor, starting at 96
input,hiddev96: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:13.1-3
/home/rafael/src/rc/linux-2.6.23-rc8/drivers/usb/core/inode.c: creating file '005'
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0040
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0004
hub 3-0:1.0: state 7 ports 4 chg 0000 evt 0000
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
ehci_hcd 0000:00:13.2: suspend root hub

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Thomas Gleixner]

On Wed, 2007-09-26 at 17:25 +0200, Rafael J. Wysocki wrote:
> There still are some oddities.
> 
> First, with the "x86-64: Disable local APIC timer use on AMD systems with C1E"
> patch and my collection of suspend patches applied, the box doesn't boot
> (the suspend patches don't even thouch the boot code, so they should be
> irrelevant here).  However, it boots if patch-2.6.23-rc7-hrt1.patch (adjusted
> for 2.6.23-rc8) is applied in addition.  Is this expected?

No. That's odd. It is nothing else than adding "noapictimer" to the
kernel command line.

> Next, on 2.6.23-rc8 with the patches from:
> 
> http://www.sisk.pl/kernel/hibernation_and_suspend/2.6.23-rc8/patches/
> 
> plus the "x86-64: Disable local APIC timer use on AMD systems with C1E" patch
> and patch-2.6.23-rc7-hrt1.patch (adjusted for 2.6.23-rc8), hibernation doesn't
> work correctly.  Although the box hibernates and restores, there is a temporary
> "hang" during the "resume hardware" sequence, after which the "lock" led starts
> to blink (and remains in this state) and something like this appears in dmesg:
> 
> Extended CMOS year: 2000
> Enabling non-boot CPUs ...
> SMP alternatives: switching to SMP code
> Booting processor 1/2 APIC 0x1
> Initializing CPU#1
> Calibrating delay using timer specific routine.. 3990.36 BogoMIPS (lpj=7980735)
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 512K (64 bytes/line)
> Unable to handle kernel paging request at ffffffff806c64d4 RIP: 
>  [<ffffffff802104cb>] identify_cpu+0x2ac/0x5a1

Hmm. That's really early in the CPU bring up. The only change in this
area is the C1E patch. Can you decode the exact source line, where it is
failing ?

	tglx

Re: 2.6.23-rc4-mm1 and -rc6-mm1: boot failure on HP nx6325, related to clockevents

[Rafael J. Wysocki]

On Wednesday, 26 September 2007 20:51, Thomas Gleixner wrote:
> On Wed, 2007-09-26 at 17:25 +0200, Rafael J. Wysocki wrote:
> > There still are some oddities.
> > 
> > First, with the "x86-64: Disable local APIC timer use on AMD systems with C1E"
> > patch and my collection of suspend patches applied, the box doesn't boot
> > (the suspend patches don't even thouch the boot code, so they should be
> > irrelevant here).  However, it boots if patch-2.6.23-rc7-hrt1.patch (adjusted
> > for 2.6.23-rc8) is applied in addition.  Is this expected?
> 
> No. That's odd. It is nothing else than adding "noapictimer" to the
> kernel command line.

Seems to be reproducible, though.  I'll investigate further.

> > Next, on 2.6.23-rc8 with the patches from:
> > 
> > http://www.sisk.pl/kernel/hibernation_and_suspend/2.6.23-rc8/patches/
> > 
> > plus the "x86-64: Disable local APIC timer use on AMD systems with C1E" patch
> > and patch-2.6.23-rc7-hrt1.patch (adjusted for 2.6.23-rc8), hibernation doesn't
> > work correctly.  Although the box hibernates and restores, there is a temporary
> > "hang" during the "resume hardware" sequence, after which the "lock" led starts
> > to blink (and remains in this state) and something like this appears in dmesg:
> > 
> > Extended CMOS year: 2000
> > Enabling non-boot CPUs ...
> > SMP alternatives: switching to SMP code
> > Booting processor 1/2 APIC 0x1
> > Initializing CPU#1
> > Calibrating delay using timer specific routine.. 3990.36 BogoMIPS (lpj=7980735)
> > CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> > CPU: L2 Cache: 512K (64 bytes/line)
> > Unable to handle kernel paging request at ffffffff806c64d4 RIP: 
> >  [<ffffffff802104cb>] identify_cpu+0x2ac/0x5a1
> 
> Hmm. That's really early in the CPU bring up. The only change in this
> area is the C1E patch. Can you decode the exact source line, where it is
> failing ?

Yes, I can, but I'll first see what's wrong with the boot.

Greetings,
Rafael