From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
To: Vinod Koul <vkoul@kernel.org>, Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org,
Bjorn Andersson <bjorn.andersson@linaro.org>,
David Airlie <airlied@linux.ie>, Daniel Vetter <daniel@ffwll.ch>,
Jonathan Marek <jonathan@marek.ca>,
Abhinav Kumar <abhinavk@codeaurora.org>,
Jeffrey Hugo <jeffrey.l.hugo@gmail.com>,
Sumit Semwal <sumit.semwal@linaro.org>,
linux-kernel@vger.kernel.org, dri-devel@lists.freedesktop.org,
freedreno@lists.freedesktop.org
Subject: Re: [PATCH v2 06/11] drm/msm/disp/dpu1: Don't use DSC with mode_3d
Date: Thu, 14 Oct 2021 16:41:50 +0300 [thread overview]
Message-ID: <11becace-7b44-6141-5a8b-1bd6d0673243@linaro.org> (raw)
In-Reply-To: <20211007070900.456044-7-vkoul@kernel.org>
On 07/10/2021 10:08, Vinod Koul wrote:
> We cannot enable mode_3d when we are using the DSC. So pass
> configuration to detect DSC is enabled and not enable mode_3d
> when we are using DSC
>
> We add a helper dpu_encoder_helper_get_dsc_mode() to detect dsc
> enabled and pass this to .setup_intf_cfg()
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
> Changes since
> v1:
> - Move this patch from 7 to 6
> - Update the changelog
> - Make dsc as int and store the DSC indices
>
> drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h | 11 +++++++++++
> drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c | 2 ++
> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c | 5 +++--
> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h | 2 ++
> 4 files changed, 18 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h
> index e7270eb6b84b..fca07ed03317 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h
> @@ -332,6 +332,17 @@ static inline enum dpu_3d_blend_mode dpu_encoder_helper_get_3d_blend_mode(
> return BLEND_3D_NONE;
> }
>
> +static inline bool dpu_encoder_helper_get_dsc_mode(struct dpu_encoder_phys *phys_enc)
> +{
> + struct drm_encoder *drm_enc = phys_enc->parent;
> + struct msm_drm_private *priv = drm_enc->dev->dev_private;
> +
> + if (priv->dsc)
> + return BIT(0) | BIT(1); /* Hardcoding for 2 DSC topology */
Please use defined values here rater than just BIT().
> +
> + return 0;
> +}
> +
> /**
> * dpu_encoder_helper_split_config - split display configuration helper function
> * This helper function may be used by physical encoders to configure
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
> index aa01698d6b25..8e5c0911734c 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
> @@ -70,6 +70,8 @@ static void _dpu_encoder_phys_cmd_update_intf_cfg(
> intf_cfg.intf_mode_sel = DPU_CTL_MODE_SEL_CMD;
> intf_cfg.stream_sel = cmd_enc->stream_sel;
> intf_cfg.mode_3d = dpu_encoder_helper_get_3d_blend_mode(phys_enc);
> + intf_cfg.dsc = dpu_encoder_helper_get_dsc_mode(phys_enc);
> +
> ctl->ops.setup_intf_cfg(ctl, &intf_cfg);
> }
>
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c
> index 64740ddb983e..3c79bd9c2fe5 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c
> @@ -118,7 +118,7 @@ static u32 dpu_hw_ctl_get_pending_flush(struct dpu_hw_ctl *ctx)
> return ctx->pending_flush_mask;
> }
>
> -static inline void dpu_hw_ctl_trigger_flush_v1(struct dpu_hw_ctl *ctx)
> +static void dpu_hw_ctl_trigger_flush_v1(struct dpu_hw_ctl *ctx)
> {
>
> if (ctx->pending_flush_mask & BIT(MERGE_3D_IDX))
> @@ -519,7 +519,8 @@ static void dpu_hw_ctl_intf_cfg(struct dpu_hw_ctl *ctx,
>
> intf_cfg |= (cfg->intf & 0xF) << 4;
>
> - if (cfg->mode_3d) {
> + /* In DSC we can't set merge, so check for dsc too */
> + if (cfg->mode_3d && !cfg->dsc) {
The more I think about this hunk, the more I'm unsure about it.
Downstream has the following topoligies defined:
* @SDE_RM_TOPOLOGY_DUALPIPE_3DMERGE_DSC: 2 LM, 2 PP, 3DMux, 1 DSC, 1
INTF/WB
* @SDE_RM_TOPOLOGY_QUADPIPE_3DMERGE_DSC 4 LM, 4 PP, 3DMux, 3 DSC, 2 INTF
While the latter is not supported on sdm845, the former one should be
(by the hardware). So in the driver I think we should make sure that
mode_3d does not get set rather than disallowing it here.
> intf_cfg |= BIT(19);
> intf_cfg |= (cfg->mode_3d - 0x1) << 20;
> }
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h
> index 806c171e5df2..5dfac5994bd4 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h
> @@ -39,6 +39,7 @@ struct dpu_hw_stage_cfg {
> * @mode_3d: 3d mux configuration
> * @merge_3d: 3d merge block used
> * @intf_mode_sel: Interface mode, cmd / vid
> + * @dsc: DSC BIT masks
> * @stream_sel: Stream selection for multi-stream interfaces
> */
> struct dpu_hw_intf_cfg {
> @@ -46,6 +47,7 @@ struct dpu_hw_intf_cfg {
> enum dpu_3d_blend_mode mode_3d;
> enum dpu_merge_3d merge_3d;
> enum dpu_ctl_mode_sel intf_mode_sel;
> + unsigned int dsc;
> int stream_sel;
> };
>
>
--
With best wishes
Dmitry
next prev parent reply other threads:[~2021-10-14 13:42 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-10-07 7:08 [PATCH v2 00/11] drm/msm: Add Display Stream Compression Support Vinod Koul
2021-10-07 7:08 ` [PATCH v2 01/11] drm/msm/dsi: add support for dsc data Vinod Koul
2021-10-25 14:43 ` Dmitry Baryshkov
2021-10-07 7:08 ` [PATCH v2 02/11] drm/msm/disp/dpu1: Add support for DSC Vinod Koul
2021-10-14 14:40 ` Dmitry Baryshkov
2021-10-19 14:07 ` Vinod Koul
2021-10-07 7:08 ` [PATCH v2 03/11] drm/msm/disp/dpu1: Add support for DSC in pingpong block Vinod Koul
2021-10-14 13:30 ` Dmitry Baryshkov
2021-10-07 7:08 ` [PATCH v2 04/11] drm/msm/disp/dpu1: Add DSC support in RM Vinod Koul
2021-10-14 14:11 ` Dmitry Baryshkov
2021-10-19 15:30 ` Vinod Koul
2021-10-19 15:52 ` Dmitry Baryshkov
2021-10-19 16:25 ` Vinod Koul
2021-10-07 7:08 ` [PATCH v2 05/11] drm/msm/disp/dpu1: Add DSC for SDM845 to hw_catalog Vinod Koul
2021-10-14 13:33 ` Dmitry Baryshkov
2021-10-07 7:08 ` [PATCH v2 06/11] drm/msm/disp/dpu1: Don't use DSC with mode_3d Vinod Koul
2021-10-14 13:41 ` Dmitry Baryshkov [this message]
2021-10-14 13:50 ` Dmitry Baryshkov
2021-10-20 6:57 ` Vinod Koul
2021-10-25 14:40 ` Dmitry Baryshkov
2021-10-25 16:10 ` Vinod Koul
2021-10-25 18:33 ` Dmitry Baryshkov
2021-10-07 7:08 ` [PATCH v2 07/11] drm/msm/disp/dpu1: Add DSC support in hw_ctl Vinod Koul
2021-10-14 14:06 ` Dmitry Baryshkov
2021-10-20 9:19 ` Vinod Koul
2021-10-07 7:08 ` [PATCH v2 08/11] drm/msm/disp/dpu1: Add support for DSC in encoder Vinod Koul
2021-10-25 14:44 ` Dmitry Baryshkov
2021-10-07 7:08 ` [PATCH v2 09/11] drm/msm/disp/dpu1: Add support for DSC in topology Vinod Koul
2021-10-14 14:13 ` Dmitry Baryshkov
2021-10-25 14:37 ` Dmitry Baryshkov
2021-10-25 16:11 ` Vinod Koul
2021-10-07 7:08 ` [PATCH v2 10/11] drm/msm/dsi: Add support for DSC configuration Vinod Koul
2021-10-14 23:18 ` Dmitry Baryshkov
2021-10-20 11:53 ` Vinod Koul
2021-10-07 7:09 ` [PATCH v2 11/11] drm/msm/dsi: Pass DSC params to drm_panel Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=11becace-7b44-6141-5a8b-1bd6d0673243@linaro.org \
--to=dmitry.baryshkov@linaro.org \
--cc=abhinavk@codeaurora.org \
--cc=airlied@linux.ie \
--cc=bjorn.andersson@linaro.org \
--cc=daniel@ffwll.ch \
--cc=dri-devel@lists.freedesktop.org \
--cc=freedreno@lists.freedesktop.org \
--cc=jeffrey.l.hugo@gmail.com \
--cc=jonathan@marek.ca \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robdclark@gmail.com \
--cc=sumit.semwal@linaro.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®