From: Primoz Fiser <primoz.fiser@norik.com>
To: Ahmad Fatoum <a.fatoum@pengutronix.de>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Shawn Guo <shawnguo@kernel.org>,
Sascha Hauer <s.hauer@pengutronix.de>,
Pengutronix Kernel Team <kernel@pengutronix.de>,
Fabio Estevam <festevam@gmail.com>
Cc: devicetree@vger.kernel.org, upstream@lists.phytec.de,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, imx@lists.linux.dev
Subject: Re: [PATCH] arm64: dts: freescale: imx93-phy{core, board}: Add i2c bus recovery
Date: Thu, 23 Oct 2025 15:18:10 +0200 [thread overview]
Message-ID: <12603435-02c5-4e85-8fd3-53cb65c9159a@norik.com> (raw)
In-Reply-To: <56075d3e-30ac-4501-bd77-2a84d0d124bd@pengutronix.de>
Hi Ahmad,
On 23. 10. 25 14:00, Ahmad Fatoum wrote:
> Hi,
>
> On 10/23/25 12:34 PM, Primoz Fiser wrote:
>> Add bus recovery feature for I2C buses on the PHYTEC phyCORE-i.MX93 SoM
>> based boards (that is phyBOARD-Nash-i.MX93 and phyBOARD-Segin-i.MX93).
>> This enables the i2c-imx-lpi2c driver to recover the stuck I2C bus by
>> switching the SCL and SDA pinmuxing and do the I2C bus bit-banging.
>>
>> Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
>> ---
>> .../arm64/boot/dts/freescale/imx93-phyboard-nash.dts | 12 +++++++++++-
>> .../boot/dts/freescale/imx93-phyboard-segin.dts | 12 +++++++++++-
>> arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi | 12 +++++++++++-
>> 3 files changed, 33 insertions(+), 3 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx93-phyboard-nash.dts b/arch/arm64/boot/dts/freescale/imx93-phyboard-nash.dts
>> index 5599e296919f..96c58cf13754 100644
>> --- a/arch/arm64/boot/dts/freescale/imx93-phyboard-nash.dts
>> +++ b/arch/arm64/boot/dts/freescale/imx93-phyboard-nash.dts
>> @@ -128,8 +128,11 @@ &flexcan1 {
>> /* I2C2 */
>> &lpi2c2 {
>> clock-frequency = <400000>;
>> - pinctrl-names = "default";
>> + pinctrl-names = "default", "gpio";
>> pinctrl-0 = <&pinctrl_lpi2c2>;
>> + pinctrl-1 = <&pinctrl_lpi2c2_gpio>;
>> + scl-gpios = <&gpio1 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
>> + sda-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
>> status = "okay";
>>
>> /* RTC */
>> @@ -253,6 +256,13 @@ MX93_PAD_I2C2_SDA__LPI2C2_SDA 0x40000b9e
>> >;
>> };
>>
>> + pinctrl_lpi2c2_gpio: lpi2c2gpiogrp {
>> + fsl,pins = <
>> + MX93_PAD_I2C2_SCL__GPIO1_IO02 0x31e
>
> I haven't worked with imx93 myself yet, but does this not need the SION
> bit set?
That's a good question.
It seems other in-tree platforms using imx7ulp-lpi2c driver like imx7,
imx8q, imx8mp are setting the SION bit indeed.
However, since we are using the generic I2C GPIO recovery routine, SION
bit probably doesn't need to be set because recovery routine will apply
"gpio" pinctrl via the pinctrl_select_state(), toggle the SDA/SCL lines
now muxed as gpios and lastly apply back the original "i2c" pinctrl.
So I would assume SION bit would need to be set if driver would try to
recover the bus while keeping the original i2c pad muxing?
For which platform was SION bit necessary in your case?
BR,
Primoz
>
> Cheers,
> Ahmad
>
>> + MX93_PAD_I2C2_SDA__GPIO1_IO03 0x31e
>> + >;
>> + };
>> +
>> pinctrl_lpspi6: lpspi6grp {
>> fsl,pins = <
>> MX93_PAD_GPIO_IO00__GPIO2_IO00 0x386
>> diff --git a/arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts b/arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts
>> index 802d96b19e4c..1850a93dbaa4 100644
>> --- a/arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts
>> +++ b/arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts
>> @@ -132,8 +132,11 @@ &flexcan1 {
>> /* I2C2 */
>> &lpi2c2 {
>> clock-frequency = <400000>;
>> - pinctrl-names = "default";
>> + pinctrl-names = "default", "gpio";
>> pinctrl-0 = <&pinctrl_lpi2c2>;
>> + pinctrl-1 = <&pinctrl_lpi2c2_gpio>;
>> + scl-gpios = <&gpio1 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
>> + sda-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
>> status = "okay";
>>
>> /* Codec */
>> @@ -238,6 +241,13 @@ MX93_PAD_I2C2_SDA__LPI2C2_SDA 0x40000b9e
>> >;
>> };
>>
>> + pinctrl_lpi2c2_gpio: lpi2c2gpiogrp {
>> + fsl,pins = <
>> + MX93_PAD_I2C2_SCL__GPIO1_IO02 0x31e
>> + MX93_PAD_I2C2_SDA__GPIO1_IO03 0x31e
>> + >;
>> + };
>> +
>> pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
>> fsl,pins = <
>> MX93_PAD_SD2_RESET_B__GPIO3_IO07 0x31e
>> diff --git a/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
>> index 3f069905cf0b..ebc57841f27f 100644
>> --- a/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
>> +++ b/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
>> @@ -93,8 +93,11 @@ ethphy1: ethernet-phy@1 {
>> /* I2C3 */
>> &lpi2c3 {
>> clock-frequency = <400000>;
>> - pinctrl-names = "default";
>> + pinctrl-names = "default", "gpio";
>> pinctrl-0 = <&pinctrl_lpi2c3>;
>> + pinctrl-1 = <&pinctrl_lpi2c3_gpio>;
>> + scl-gpios = <&gpio2 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
>> + sda-gpios = <&gpio2 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
>> status = "okay";
>>
>> pmic@25 {
>> @@ -234,6 +237,13 @@ MX93_PAD_GPIO_IO29__LPI2C3_SCL 0x40000b9e
>> >;
>> };
>>
>> + pinctrl_lpi2c3_gpio: lpi2c3gpiogrp {
>> + fsl,pins = <
>> + MX93_PAD_GPIO_IO28__GPIO2_IO28 0x31e
>> + MX93_PAD_GPIO_IO29__GPIO2_IO29 0x31e
>> + >;
>> + };
>> +
>> pinctrl_pmic: pmicgrp {
>> fsl,pins = <
>> MX93_PAD_ENET2_RD3__GPIO4_IO27 0x31e
>
--
Primoz Fiser
phone: +386-41-390-545
email: primoz.fiser@norik.com
--
Norik systems d.o.o.
Your embedded software partner
Slovenia, EU
phone: +386-41-540-545
email: info@norik.com
next prev parent reply other threads:[~2025-10-23 13:18 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-10-23 10:34 [PATCH] arm64: dts: freescale: imx93-phy{core,board}: " Primoz Fiser
2025-10-23 12:00 ` [PATCH] arm64: dts: freescale: imx93-phy{core, board}: " Ahmad Fatoum
2025-10-23 13:18 ` Primoz Fiser [this message]
2026-02-23 23:45 ` [PATCH] arm64: dts: freescale: imx93-phy{core,board}: " Frank Li
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=12603435-02c5-4e85-8fd3-53cb65c9159a@norik.com \
--to=primoz.fiser@norik.com \
--cc=a.fatoum@pengutronix.de \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=imx@lists.linux.dev \
--cc=kernel@pengutronix.de \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
--cc=upstream@lists.phytec.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®