From: Ahmad Fatoum <a.fatoum@pengutronix.de>
To: Primoz Fiser <primoz.fiser@norik.com>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Shawn Guo <shawnguo@kernel.org>,
Sascha Hauer <s.hauer@pengutronix.de>,
Pengutronix Kernel Team <kernel@pengutronix.de>,
Fabio Estevam <festevam@gmail.com>
Cc: devicetree@vger.kernel.org, upstream@lists.phytec.de,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, imx@lists.linux.dev
Subject: Re: [PATCH] arm64: dts: freescale: imx93-phy{core, board}: Add i2c bus recovery
Date: Thu, 23 Oct 2025 14:00:46 +0200 [thread overview]
Message-ID: <56075d3e-30ac-4501-bd77-2a84d0d124bd@pengutronix.de> (raw)
In-Reply-To: <20251023103426.3606647-1-primoz.fiser@norik.com>
Hi,
On 10/23/25 12:34 PM, Primoz Fiser wrote:
> Add bus recovery feature for I2C buses on the PHYTEC phyCORE-i.MX93 SoM
> based boards (that is phyBOARD-Nash-i.MX93 and phyBOARD-Segin-i.MX93).
> This enables the i2c-imx-lpi2c driver to recover the stuck I2C bus by
> switching the SCL and SDA pinmuxing and do the I2C bus bit-banging.
>
> Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
> ---
> .../arm64/boot/dts/freescale/imx93-phyboard-nash.dts | 12 +++++++++++-
> .../boot/dts/freescale/imx93-phyboard-segin.dts | 12 +++++++++++-
> arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi | 12 +++++++++++-
> 3 files changed, 33 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx93-phyboard-nash.dts b/arch/arm64/boot/dts/freescale/imx93-phyboard-nash.dts
> index 5599e296919f..96c58cf13754 100644
> --- a/arch/arm64/boot/dts/freescale/imx93-phyboard-nash.dts
> +++ b/arch/arm64/boot/dts/freescale/imx93-phyboard-nash.dts
> @@ -128,8 +128,11 @@ &flexcan1 {
> /* I2C2 */
> &lpi2c2 {
> clock-frequency = <400000>;
> - pinctrl-names = "default";
> + pinctrl-names = "default", "gpio";
> pinctrl-0 = <&pinctrl_lpi2c2>;
> + pinctrl-1 = <&pinctrl_lpi2c2_gpio>;
> + scl-gpios = <&gpio1 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> status = "okay";
>
> /* RTC */
> @@ -253,6 +256,13 @@ MX93_PAD_I2C2_SDA__LPI2C2_SDA 0x40000b9e
> >;
> };
>
> + pinctrl_lpi2c2_gpio: lpi2c2gpiogrp {
> + fsl,pins = <
> + MX93_PAD_I2C2_SCL__GPIO1_IO02 0x31e
I haven't worked with imx93 myself yet, but does this not need the SION
bit set?
Cheers,
Ahmad
> + MX93_PAD_I2C2_SDA__GPIO1_IO03 0x31e
> + >;
> + };
> +
> pinctrl_lpspi6: lpspi6grp {
> fsl,pins = <
> MX93_PAD_GPIO_IO00__GPIO2_IO00 0x386
> diff --git a/arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts b/arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts
> index 802d96b19e4c..1850a93dbaa4 100644
> --- a/arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts
> +++ b/arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts
> @@ -132,8 +132,11 @@ &flexcan1 {
> /* I2C2 */
> &lpi2c2 {
> clock-frequency = <400000>;
> - pinctrl-names = "default";
> + pinctrl-names = "default", "gpio";
> pinctrl-0 = <&pinctrl_lpi2c2>;
> + pinctrl-1 = <&pinctrl_lpi2c2_gpio>;
> + scl-gpios = <&gpio1 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> status = "okay";
>
> /* Codec */
> @@ -238,6 +241,13 @@ MX93_PAD_I2C2_SDA__LPI2C2_SDA 0x40000b9e
> >;
> };
>
> + pinctrl_lpi2c2_gpio: lpi2c2gpiogrp {
> + fsl,pins = <
> + MX93_PAD_I2C2_SCL__GPIO1_IO02 0x31e
> + MX93_PAD_I2C2_SDA__GPIO1_IO03 0x31e
> + >;
> + };
> +
> pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
> fsl,pins = <
> MX93_PAD_SD2_RESET_B__GPIO3_IO07 0x31e
> diff --git a/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
> index 3f069905cf0b..ebc57841f27f 100644
> --- a/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
> @@ -93,8 +93,11 @@ ethphy1: ethernet-phy@1 {
> /* I2C3 */
> &lpi2c3 {
> clock-frequency = <400000>;
> - pinctrl-names = "default";
> + pinctrl-names = "default", "gpio";
> pinctrl-0 = <&pinctrl_lpi2c3>;
> + pinctrl-1 = <&pinctrl_lpi2c3_gpio>;
> + scl-gpios = <&gpio2 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio2 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> status = "okay";
>
> pmic@25 {
> @@ -234,6 +237,13 @@ MX93_PAD_GPIO_IO29__LPI2C3_SCL 0x40000b9e
> >;
> };
>
> + pinctrl_lpi2c3_gpio: lpi2c3gpiogrp {
> + fsl,pins = <
> + MX93_PAD_GPIO_IO28__GPIO2_IO28 0x31e
> + MX93_PAD_GPIO_IO29__GPIO2_IO29 0x31e
> + >;
> + };
> +
> pinctrl_pmic: pmicgrp {
> fsl,pins = <
> MX93_PAD_ENET2_RD3__GPIO4_IO27 0x31e
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
next prev parent reply other threads:[~2025-10-23 12:01 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-10-23 10:34 [PATCH] arm64: dts: freescale: imx93-phy{core,board}: " Primoz Fiser
2025-10-23 12:00 ` Ahmad Fatoum [this message]
2025-10-23 13:18 ` [PATCH] arm64: dts: freescale: imx93-phy{core, board}: " Primoz Fiser
2026-02-23 23:45 ` [PATCH] arm64: dts: freescale: imx93-phy{core,board}: " Frank Li
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=56075d3e-30ac-4501-bd77-2a84d0d124bd@pengutronix.de \
--to=a.fatoum@pengutronix.de \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=imx@lists.linux.dev \
--cc=kernel@pengutronix.de \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=primoz.fiser@norik.com \
--cc=robh@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
--cc=upstream@lists.phytec.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®