mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: "Jean-François Dagenais" <jeff.dagenais@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: "Jean-François Dagenais" <dagenaisj@sonatest.com>,
	akpm@linux-foundation.org,
	"Evgeniy Polyakov" <johnpol@2ka.mipt.ru>
Subject: [patch v2] w1: ds1wm: add a reset recovery parameter
Date: Wed,  6 Jul 2011 09:15:55 -0400	[thread overview]
Message-ID: <1309958155-7609-1-git-send-email-dagenaisj@sonatest.com> (raw)

This follows the regression reported by Paul Parsons regarding
the removal of the msleep(1) in the ds1wm_reset() function. This
sleep should not be required on normal circuitry provided the
pull-ups on the bus are correctly adapted to the slaves.
Unfortunately, this is not always the case. The sleep is restored
but as a parameter to the probe function in the pdata.

This fixes a regression on 3.0 reported by Paul Parsons regarding the
removal of the msleep(1) in the ds1wm_reset() function:

: The linux-3.0-rc4 DS1WM 1-wire driver is logging "bus error, retrying"
: error messages on an HP iPAQ hx4700 PDA (XScale-PXA270):
:
: <snip>
: Driver for 1-wire Dallas network protocol.
: DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko
: 1-Wire driver for the DS2760 battery monitor  chip  - (c) 2004-2005, Szabolcs Gyurko
: ds1wm ds1wm: pass: 1 bus error, retrying
: ds1wm ds1wm: pass: 2 bus error, retrying
: ds1wm ds1wm: pass: 3 bus error, retrying
: ds1wm ds1wm: pass: 4 bus error, retrying
: ds1wm ds1wm: pass: 5 bus error, retrying
: ...
:
: The visible result is that the battery charging LED is erratic; sometimes
: it works, mostly it doesn't.
:
: The linux-2.6.39 DS1WM 1-wire driver worked OK.  I haven't tried 3.0-rc1,
: 3.0-rc2, or 3.0-rc3.

This sleep should not be required on normal circuitry provided the
pull-ups on the bus are correctly adapted to the slaves.  Unfortunately,
this is not always the case.  The sleep is restored but as a parameter to
the probe function in the pdata.

Reported-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
---
 drivers/mfd/asic3.c        |    1 +
 drivers/mfd/htc-pasic3.c   |    1 +
 drivers/w1/masters/ds1wm.c |    5 +++++
 include/linux/mfd/ds1wm.h  |    7 +++++++
 4 files changed, 14 insertions(+), 0 deletions(-)

diff --git a/drivers/mfd/asic3.c b/drivers/mfd/asic3.c
index c27fd1f..c71ae09 100644
--- a/drivers/mfd/asic3.c
+++ b/drivers/mfd/asic3.c
@@ -619,6 +619,7 @@ static void asic3_clk_disable(struct asic3 *asic, struct asic3_clk *clk)
 /* MFD cells (SPI, PWM, LED, DS1WM, MMC) */
 static struct ds1wm_driver_data ds1wm_pdata = {
 	.active_high = 1,
+	.reset_recover_delay = 1,
 };
 
 static struct resource ds1wm_resources[] = {
diff --git a/drivers/mfd/htc-pasic3.c b/drivers/mfd/htc-pasic3.c
index 2808bd1..04c7093 100644
--- a/drivers/mfd/htc-pasic3.c
+++ b/drivers/mfd/htc-pasic3.c
@@ -99,6 +99,7 @@ static int ds1wm_disable(struct platform_device *pdev)
 
 static struct ds1wm_driver_data ds1wm_pdata = {
 	.active_high = 0,
+	.reset_recover_delay = 1,
 };
 
 static struct resource ds1wm_resources[] __initdata = {
diff --git a/drivers/w1/masters/ds1wm.c b/drivers/w1/masters/ds1wm.c
index ad57593..66bf82f 100644
--- a/drivers/w1/masters/ds1wm.c
+++ b/drivers/w1/masters/ds1wm.c
@@ -109,6 +109,7 @@ struct ds1wm_data {
 	/* byte to write that makes all intr disabled, */
 	/* considering active_state (IAS) (optimization) */
 	u8       int_en_reg_none;
+	unsigned int reset_recover_delay; /* see ds1wm.h */
 };
 
 static inline void ds1wm_write_register(struct ds1wm_data *ds1wm_data, u32 reg,
@@ -187,6 +188,9 @@ static int ds1wm_reset(struct ds1wm_data *ds1wm_data)
 		return 1;
 	}
 
+	if(ds1wm_data->reset_recover_delay)
+		msleep(ds1wm_data->reset_recover_delay);
+
 	return 0;
 }
 
@@ -490,6 +494,7 @@ static int ds1wm_probe(struct platform_device *pdev)
 	}
 	ds1wm_data->irq = res->start;
 	ds1wm_data->int_en_reg_none = (plat->active_high ? DS1WM_INTEN_IAS : 0);
+	ds1wm_data->reset_recover_delay = plat->reset_recover_delay;
 
 	if (res->flags & IORESOURCE_IRQ_HIGHEDGE)
 		irq_set_irq_type(ds1wm_data->irq, IRQ_TYPE_EDGE_RISING);
diff --git a/include/linux/mfd/ds1wm.h b/include/linux/mfd/ds1wm.h
index be469a3..068044f 100644
--- a/include/linux/mfd/ds1wm.h
+++ b/include/linux/mfd/ds1wm.h
@@ -3,4 +3,11 @@
 struct ds1wm_driver_data {
 	int active_high;
 	int clock_rate;
+	/* in milliseconds, the amount of time to */
+	/* sleep following a reset pulse. Zero    */
+	/* should work if your bus devices recover*/
+	/* time respects the 1-wire spec since the*/
+	/* ds1wm implements the precise timings of*/
+	/* a reset pulse/presence detect sequence.*/ 
+	unsigned int reset_recover_delay;
 };
-- 
1.7.5.4


                 reply	other threads:[~2011-07-06 13:16 UTC|newest]

Thread overview: [no followups] expand[flat|nested]  mbox.gz  Atom feed

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1309958155-7609-1-git-send-email-dagenaisj@sonatest.com \
    --to=jeff.dagenais@gmail.com \
    --cc=akpm@linux-foundation.org \
    --cc=dagenaisj@sonatest.com \
    --cc=johnpol@2ka.mipt.ru \
    --cc=linux-kernel@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®