* [patch v2] w1: ds1wm: add a reset recovery parameter
@ 2011-07-06 13:15 Jean-François Dagenais
0 siblings, 0 replies; only message in thread
From: Jean-François Dagenais @ 2011-07-06 13:15 UTC (permalink / raw)
To: linux-kernel; +Cc: Jean-François Dagenais, akpm, Evgeniy Polyakov
This follows the regression reported by Paul Parsons regarding
the removal of the msleep(1) in the ds1wm_reset() function. This
sleep should not be required on normal circuitry provided the
pull-ups on the bus are correctly adapted to the slaves.
Unfortunately, this is not always the case. The sleep is restored
but as a parameter to the probe function in the pdata.
This fixes a regression on 3.0 reported by Paul Parsons regarding the
removal of the msleep(1) in the ds1wm_reset() function:
: The linux-3.0-rc4 DS1WM 1-wire driver is logging "bus error, retrying"
: error messages on an HP iPAQ hx4700 PDA (XScale-PXA270):
:
: <snip>
: Driver for 1-wire Dallas network protocol.
: DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko
: 1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005, Szabolcs Gyurko
: ds1wm ds1wm: pass: 1 bus error, retrying
: ds1wm ds1wm: pass: 2 bus error, retrying
: ds1wm ds1wm: pass: 3 bus error, retrying
: ds1wm ds1wm: pass: 4 bus error, retrying
: ds1wm ds1wm: pass: 5 bus error, retrying
: ...
:
: The visible result is that the battery charging LED is erratic; sometimes
: it works, mostly it doesn't.
:
: The linux-2.6.39 DS1WM 1-wire driver worked OK. I haven't tried 3.0-rc1,
: 3.0-rc2, or 3.0-rc3.
This sleep should not be required on normal circuitry provided the
pull-ups on the bus are correctly adapted to the slaves. Unfortunately,
this is not always the case. The sleep is restored but as a parameter to
the probe function in the pdata.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
---
drivers/mfd/asic3.c | 1 +
drivers/mfd/htc-pasic3.c | 1 +
drivers/w1/masters/ds1wm.c | 5 +++++
include/linux/mfd/ds1wm.h | 7 +++++++
4 files changed, 14 insertions(+), 0 deletions(-)
diff --git a/drivers/mfd/asic3.c b/drivers/mfd/asic3.c
index c27fd1f..c71ae09 100644
--- a/drivers/mfd/asic3.c
+++ b/drivers/mfd/asic3.c
@@ -619,6 +619,7 @@ static void asic3_clk_disable(struct asic3 *asic, struct asic3_clk *clk)
/* MFD cells (SPI, PWM, LED, DS1WM, MMC) */
static struct ds1wm_driver_data ds1wm_pdata = {
.active_high = 1,
+ .reset_recover_delay = 1,
};
static struct resource ds1wm_resources[] = {
diff --git a/drivers/mfd/htc-pasic3.c b/drivers/mfd/htc-pasic3.c
index 2808bd1..04c7093 100644
--- a/drivers/mfd/htc-pasic3.c
+++ b/drivers/mfd/htc-pasic3.c
@@ -99,6 +99,7 @@ static int ds1wm_disable(struct platform_device *pdev)
static struct ds1wm_driver_data ds1wm_pdata = {
.active_high = 0,
+ .reset_recover_delay = 1,
};
static struct resource ds1wm_resources[] __initdata = {
diff --git a/drivers/w1/masters/ds1wm.c b/drivers/w1/masters/ds1wm.c
index ad57593..66bf82f 100644
--- a/drivers/w1/masters/ds1wm.c
+++ b/drivers/w1/masters/ds1wm.c
@@ -109,6 +109,7 @@ struct ds1wm_data {
/* byte to write that makes all intr disabled, */
/* considering active_state (IAS) (optimization) */
u8 int_en_reg_none;
+ unsigned int reset_recover_delay; /* see ds1wm.h */
};
static inline void ds1wm_write_register(struct ds1wm_data *ds1wm_data, u32 reg,
@@ -187,6 +188,9 @@ static int ds1wm_reset(struct ds1wm_data *ds1wm_data)
return 1;
}
+ if(ds1wm_data->reset_recover_delay)
+ msleep(ds1wm_data->reset_recover_delay);
+
return 0;
}
@@ -490,6 +494,7 @@ static int ds1wm_probe(struct platform_device *pdev)
}
ds1wm_data->irq = res->start;
ds1wm_data->int_en_reg_none = (plat->active_high ? DS1WM_INTEN_IAS : 0);
+ ds1wm_data->reset_recover_delay = plat->reset_recover_delay;
if (res->flags & IORESOURCE_IRQ_HIGHEDGE)
irq_set_irq_type(ds1wm_data->irq, IRQ_TYPE_EDGE_RISING);
diff --git a/include/linux/mfd/ds1wm.h b/include/linux/mfd/ds1wm.h
index be469a3..068044f 100644
--- a/include/linux/mfd/ds1wm.h
+++ b/include/linux/mfd/ds1wm.h
@@ -3,4 +3,11 @@
struct ds1wm_driver_data {
int active_high;
int clock_rate;
+ /* in milliseconds, the amount of time to */
+ /* sleep following a reset pulse. Zero */
+ /* should work if your bus devices recover*/
+ /* time respects the 1-wire spec since the*/
+ /* ds1wm implements the precise timings of*/
+ /* a reset pulse/presence detect sequence.*/
+ unsigned int reset_recover_delay;
};
--
1.7.5.4
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2011-07-06 13:16 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2011-07-06 13:15 [patch v2] w1: ds1wm: add a reset recovery parameter Jean-François Dagenais
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®