From: Roger Quadros <rogerq@ti.com>
To: <tony@atomide.com>
Cc: <b-cousson@ti.com>, <balbi@ti.com>, <gregkh@linuxfoundation.org>,
<stern@rowland.harvard.edu>, <linux@arm.linux.org.uk>,
<kishon@ti.com>, <mark.rutland@arm.com>, <rogerq@ti.com>,
<linux-omap@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>
Subject: [PATCH v2 11/14] ARM: dts: omap4-panda: Add USB Host support
Date: Thu, 7 Feb 2013 18:02:51 +0200 [thread overview]
Message-ID: <1360252974-7912-12-git-send-email-rogerq@ti.com> (raw)
In-Reply-To: <1360252974-7912-1-git-send-email-rogerq@ti.com>
Provide the RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.
Also provide pin multiplexer information for the USB host
pins.
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
arch/arm/boot/dts/omap4-panda.dts | 55 +++++++++++++++++++++++++++++++++++++
1 files changed, 55 insertions(+), 0 deletions(-)
diff --git a/arch/arm/boot/dts/omap4-panda.dts b/arch/arm/boot/dts/omap4-panda.dts
index 4122efe..d6e59c7 100644
--- a/arch/arm/boot/dts/omap4-panda.dts
+++ b/arch/arm/boot/dts/omap4-panda.dts
@@ -57,6 +57,35 @@
"AFML", "Line In",
"AFMR", "Line In";
};
+
+ /* HS USB Port 1 RESET */
+ hsusb1_reset: hsusb1_reset_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb1_reset";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 30 0>; /* gpio_62 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
+ /* HS USB Port 1 Power */
+ hsusb1_power: hsusb1_power_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb1_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 1 0>; /* gpio_1 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
+ /* HS USB Host PHY on PORT 1 */
+ hsusb1_phy: hsusb1_phy {
+ compatible = "usb-nop-xceiv";
+ reset-supply = <&hsusb1_reset>;
+ vcc-supply = <&hsusb1_power>;
+ };
};
&omap4_pmx_core {
@@ -67,6 +96,7 @@
&mcbsp1_pins
&dss_hdmi_pins
&tpd12s015_pins
+ &hsusbb1_pins
>;
twl6040_pins: pinmux_twl6040_pins {
@@ -110,6 +140,23 @@
0x58 0x10b /* hdmi_hpd.gpio_63 INPUT PULLDOWN | MODE3 */
>;
};
+
+ hsusbb1_pins: pinmux_hsusbb1_pins {
+ pinctrl-single,pins = <
+ 0x82 0x10C /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_clk INPUT | PULLDOWN */
+ 0x84 0x4 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_stp OUTPUT */
+ 0x86 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dir INPUT | PULLDOWN */
+ 0x88 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_nxt INPUT | PULLDOWN */
+ 0x8a 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat0 INPUT | PULLDOWN */
+ 0x8c 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat1 INPUT | PULLDOWN */
+ 0x8e 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat2 INPUT | PULLDOWN */
+ 0x90 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat3 INPUT | PULLDOWN */
+ 0x92 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat4 INPUT | PULLDOWN */
+ 0x94 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat5 INPUT | PULLDOWN */
+ 0x96 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat6 INPUT | PULLDOWN */
+ 0x98 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat7 INPUT | PULLDOWN */
+ >;
+ };
};
&i2c1 {
@@ -206,3 +253,11 @@
&twl_usb_comparator {
usb-supply = <&vusb>;
};
+
+&usbhshost {
+ port1-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <&hsusb1_phy>;
+};
--
1.7.4.1
next prev parent reply other threads:[~2013-02-07 16:04 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-02-07 16:02 [PATCH v2 00/14] Device tree support for OMAP HS USB Host Roger Quadros
2013-02-07 16:02 ` [PATCH v2 01/14] usb: phy: nop: Add device tree support and binding information Roger Quadros
2013-02-11 11:40 ` Mark Rutland
2013-02-11 15:14 ` Roger Quadros
2013-02-11 15:31 ` Mark Rutland
2013-02-07 16:02 ` [PATCH v2 02/14] USB: phy: nop: Defer probe if device needs VCC/RESET Roger Quadros
2013-02-07 16:02 ` [PATCH v2 03/14] mfd: omap-usb-tll: move configuration code to omap_tll_init() Roger Quadros
2013-02-07 16:02 ` [PATCH v2 04/14] mfd: omap-usb-tll: Add device tree support Roger Quadros
2013-02-07 16:02 ` [PATCH v2 05/14] USB: ehci-omap: Get platform resources by index rather than by name Roger Quadros
2013-02-07 16:02 ` [PATCH v2 06/14] USB: ohci-omap3: " Roger Quadros
2013-02-07 16:02 ` [PATCH v2 07/14] USB: ohci-omap3: Add device tree support and binding information Roger Quadros
2013-02-11 11:46 ` Mark Rutland
2013-02-11 15:22 ` Roger Quadros
2013-02-11 15:32 ` Mark Rutland
2013-02-07 16:02 ` [PATCH v2 08/14] USB: ehci-omap: " Roger Quadros
2013-02-11 11:52 ` Mark Rutland
2013-02-07 16:02 ` [PATCH v2 09/14] mfd: omap-usb-host: " Roger Quadros
2013-02-11 12:00 ` Mark Rutland
2013-02-11 15:24 ` Roger Quadros
2013-02-07 16:02 ` [PATCH v2 10/14] ARM: dts: OMAP4: Add HS USB Host IP nodes Roger Quadros
2013-02-07 16:02 ` Roger Quadros [this message]
2013-02-07 16:02 ` [PATCH v2 12/14] ARM: dts: OMAP3: " Roger Quadros
2013-02-07 16:02 ` [PATCH v2 13/14] ARM: dts: omap3-beagle: Add USB Host support Roger Quadros
2013-02-07 16:02 ` [PATCH v2 14/14] USB: ehci-omap: Fix autoloading of module Roger Quadros
2013-02-07 16:11 ` Alan Stern
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1360252974-7912-12-git-send-email-rogerq@ti.com \
--to=rogerq@ti.com \
--cc=b-cousson@ti.com \
--cc=balbi@ti.com \
--cc=gregkh@linuxfoundation.org \
--cc=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=linux@arm.linux.org.uk \
--cc=mark.rutland@arm.com \
--cc=stern@rowland.harvard.edu \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®