From: Hayes Wang <hayeswang@realtek.com>
To: <romieu@fr.zoreil.com>
Cc: <netdev@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Hayes Wang <hayeswang@realtek.com>
Subject: [PATCH v2 net-next 7/8] r8169: adjust the flow of hw_start
Date: Tue, 2 Apr 2013 16:23:41 +0800 [thread overview]
Message-ID: <1364891022-3220-7-git-send-email-hayeswang@realtek.com> (raw)
In-Reply-To: <1364891022-3220-1-git-send-email-hayeswang@realtek.com>
The suggestion as following:
- initial settings or default settings
- rtl_hw_start_xxx. rtl_hw_start_xxx may change some default settings.
- enable tx/rx. This has to be after the above two steps.
- rtl_set_rx_mode. AcceptXXXs have to be enabled after enabling tx/rx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
---
drivers/net/ethernet/realtek/r8169.c | 34 +++++++++++++++++-----------------
1 file changed, 17 insertions(+), 17 deletions(-)
diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c
index 573b693..85536bf 100644
--- a/drivers/net/ethernet/realtek/r8169.c
+++ b/drivers/net/ethernet/realtek/r8169.c
@@ -5240,10 +5240,7 @@ static void rtl_hw_start_8168(struct net_device *dev)
rtl_set_rx_tx_desc_registers(tp, ioaddr);
- rtl_set_rx_mode(dev);
-
- RTL_W32(TxConfig, (TX_DMA_BURST << TxDMAShift) |
- (InterFrameGap << TxInterFrameGapShift));
+ rtl_set_rx_tx_config_registers(tp);
RTL_R8(IntrMask);
@@ -5330,9 +5327,11 @@ static void rtl_hw_start_8168(struct net_device *dev)
break;
}
+ RTL_W8(Cfg9346, Cfg9346_Lock);
+
RTL_W8(ChipCmd, CmdTxEnb | CmdRxEnb);
- RTL_W8(Cfg9346, Cfg9346_Lock);
+ rtl_set_rx_mode(dev);
RTL_W16(MultiIntr, RTL_R16(MultiIntr) & 0xF000);
}
@@ -5490,6 +5489,17 @@ static void rtl_hw_start_8101(struct net_device *dev)
RTL_W8(Cfg9346, Cfg9346_Unlock);
+ RTL_W8(MaxTxPacketSize, TxPacketMax);
+
+ rtl_set_rx_max_size(ioaddr, rx_buf_sz);
+
+ tp->cp_cmd &= ~R810X_CPCMD_QUIRK_MASK;
+ RTL_W16(CPlusCmd, tp->cp_cmd);
+
+ rtl_set_rx_tx_desc_registers(tp, ioaddr);
+
+ rtl_set_rx_tx_config_registers(tp);
+
switch (tp->mac_version) {
case RTL_GIGA_MAC_VER_07:
rtl_hw_start_8102e_1(tp);
@@ -5521,24 +5531,14 @@ static void rtl_hw_start_8101(struct net_device *dev)
RTL_W8(Cfg9346, Cfg9346_Lock);
- RTL_W8(MaxTxPacketSize, TxPacketMax);
-
- rtl_set_rx_max_size(ioaddr, rx_buf_sz);
-
- tp->cp_cmd &= ~R810X_CPCMD_QUIRK_MASK;
- RTL_W16(CPlusCmd, tp->cp_cmd);
-
RTL_W16(IntrMitigate, 0x0000);
- rtl_set_rx_tx_desc_registers(tp, ioaddr);
-
RTL_W8(ChipCmd, CmdTxEnb | CmdRxEnb);
- rtl_set_rx_tx_config_registers(tp);
-
- RTL_R8(IntrMask);
rtl_set_rx_mode(dev);
+ RTL_R8(IntrMask);
+
RTL_W16(MultiIntr, RTL_R16(MultiIntr) & 0xf000);
}
--
1.8.1
next prev parent reply other threads:[~2013-04-02 8:26 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-04-01 13:55 [PATCH net-next 1/7] r8169: Remove firmware code Hayes Wang
2013-04-01 13:55 ` [PATCH net-next 2/7] r8169: Update PHY settings of RTL8111G Hayes Wang
2013-04-01 22:20 ` Francois Romieu
2013-04-02 2:19 ` hayeswang
2013-04-01 13:55 ` [PATCH net-next 3/7] r8169: Modify the method for setting firmware Hayes Wang
2013-04-01 13:55 ` [PATCH net-next 4/7] r8169: Update the RTL8111G parameters Hayes Wang
2013-04-01 13:55 ` [PATCH net-next 5/7] r8169: add a new chip for RTL8111G Hayes Wang
2013-04-01 22:22 ` Francois Romieu
2013-04-02 2:39 ` hayeswang
2013-04-02 23:20 ` Francois Romieu
2013-04-02 23:26 ` David Miller
2013-04-01 13:55 ` [PATCH net-next 6/7] r8169: add a new chip for RTL8106E Hayes Wang
2013-04-01 22:23 ` Francois Romieu
2013-04-02 2:59 ` hayeswang
2013-04-01 13:55 ` [PATCH net-next 7/7] r8169: fix could not dump registers Hayes Wang
2013-04-01 14:07 ` Sergei Shtylyov
2013-04-01 22:24 ` Francois Romieu
2013-04-02 8:23 ` [PATCH v2 net-next 1/8] r8169: Remove firmware code Hayes Wang
2013-04-02 8:23 ` [PATCH v2 net-next 2/8] r8169: Modify the mothod for PHY settings of RTL8111G Hayes Wang
2013-04-02 8:23 ` [PATCH v2 net-next 3/8] r8169: Update " Hayes Wang
2013-04-02 8:23 ` [PATCH v2 net-next 4/8] r8169: Modify the method for setting firmware Hayes Wang
2013-04-02 8:23 ` [PATCH v2 net-next 5/8] r8169: Update the RTL8111G parameters Hayes Wang
2013-04-02 8:23 ` [PATCH v2 net-next 6/8] r8169: add a new chip for RTL8111G Hayes Wang
2013-04-02 22:27 ` Francois Romieu
2013-04-03 3:03 ` hayeswang
2013-04-03 5:59 ` Francois Romieu
2013-04-02 8:23 ` Hayes Wang [this message]
2013-04-02 8:23 ` [PATCH v2 net-next 8/8] r8169: add a new chip for RTL8106E Hayes Wang
2013-04-04 21:47 ` [PATCH v2 net-next 1/8] r8169: Remove firmware code David Miller
2013-04-04 23:42 ` Francois Romieu
2013-04-07 20:45 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1364891022-3220-7-git-send-email-hayeswang@realtek.com \
--to=hayeswang@realtek.com \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=romieu@fr.zoreil.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®