Re: [PATCH 3/3] PowerPC/mpc85xx: Add hotplug support on E6500 cores

[Scott Wood <scottwood@freescale.com>]

On Thu, 2015-08-06 at 12:32 +0800, Chenhui Zhao wrote:
> On Thu, Aug 6, 2015 at 11:16 AM, Scott Wood <scottwood@freescale.com> 
> wrote:
> > On Wed, 2015-08-05 at 19:08 +0800, Chenhui Zhao wrote:
> > >  On Sat, Aug 1, 2015 at 8:22 AM, Scott Wood <scottwood@freescale.com>
> > >  wrote:
> > >  > On Fri, 2015-07-31 at 17:20 +0800,  b29983@freescale.comwrote:
> > >  > >  +             /*
> > >  > >  +              * If both threads are offline, reset core to 
> > > start.
> > >  > >  +              * When core is up, Thread 0 always gets up 
> > > first,
> > >  > >  +              * so bind the current logical cpu with Thread 0.
> > >  > >  +              */
> > >  > >  +             if (hw_cpu != cpu_first_thread_sibling(hw_cpu)) {
> > >  > >  +                     int hw_cpu1, hw_cpu2;
> > >  > >  +
> > >  > >  +                     hw_cpu1 = 
> > > get_hard_smp_processor_id(primary);
> > >  > >  +                     hw_cpu2 = 
> > > get_hard_smp_processor_id(primary +
> > >  > > 1);
> > >  > >  +                     set_hard_smp_processor_id(primary, 
> > > hw_cpu2);
> > >  > >  +                     set_hard_smp_processor_id(primary + 1,
> > >  > > hw_cpu1);
> > >  > >  +                     /* get new physical cpu id */
> > >  > >  +                     hw_cpu = get_hard_smp_processor_id(nr);
> > >  >
> > >  > NACK as discussed in http://patchwork.ozlabs.org/patch/454944/
> > >  >
> > >  > -Scott
> > > 
> > >  You said,
> > > 
> > >      There's no need for this. I have booting from a thread1, and 
> > > having
> > >  it
> > >      kick its thread0, working locally without messing with the 
> > > hwid/cpu
> > >      mapping.
> > > 
> > >  I still have questions here. After a core reset, how can you boot
> > >  Thread1
> > >  of the core first. As I know, Thread0 boots up first by default.
> > 
> > So the issue isn't that thread1 comes up first, but that you *want* 
> > thread1
> > to come up first and it won't.  I don't think this remapping is an 
> > acceptable
> > answer, though.  Instead, if you need only thread1 to come up, start 
> > the
> > core, have thread0 start thread1, and then send thread0 into whatever 
> > waiting
> > state it would be in if thread1 had never been offlined.
> > 
> > -Scott
> 
> Remapping is a concise solution. what's the harm of it?
> Keeping things simple is good in my opinion.

Remapping is not simple.  Remapping will make debugging more complicated (I 
see an oops on CPU <n>, which CPU's registers do I dump in the debugger?), 
could expose bugs where smp_processor_id() is used where 
hard_smp_processor_id() is needed, etc.

Having thread0 start thread1 and then go wherever it would have gone if 
thread1 were up the whole time is much more straightforward.

-Scott