QEMU fw_cfg DMA interface

QEMU fw_cfg DMA interface

[Marc Marí]

Implementation of the FW CFG DMA interface.

When running a Linux guest on top of QEMU, using the -kernel options, this
is the timing improvement for x86:

QEMU commit 16a1b6e and SeaBIOS commit e4d2b8c
QEMU startup time: .080
BIOS startup time: .060
Kernel setup time: .586
Total time: .726

QEMU with this patch series and SeaBIOS with this patch series
QEMU startup time: .080
BIOS startup time: .039
Kernel setup time: .002
Total time: .121

QEMU startup time is the time between the start and the first kvm_entry.
BIOS startup time is the time between the first kvm_entry and the start of
function do_boot, in SeaBIOS.
Kernel setup time is the time between the start of the function do_boot in
SeaBIOS and the jump to the Linux kernel.

As you can see, both the BIOS (because of ACPI tables and other configurations)
and the Linux kernel boot (because of the copy to memory) are greatly
improved with this new interface.

Also, this new interface is an addon to the old interface. Both interfaces
are compatible and interchangeable.

Changes from v1:
 - Take into account order of fields in the FWCfgDmaAccess structure
 - Check and change endianness of FWCfgDmaAccess fields
 - Change order of fields in the FWCfgDmaAccess structure
 - Add FW_CFG_DMA_CTL_SKIP feature for control field
 - Split FW_CFG_SIZE in QEMU
 - Make FW_CFG_ID a bitmap of features
 - Add 64 bit address support for the transfer. Trigger when writing the low
   address, and address is 0 by default and at the end of each transfer.
 - Align ports and addresses.
 - Preserve old fw_cfg_comb_valid behaviour in QEMU
 - Update documentation to reflect all these changes

Changes from v2:
 - Make IOports fw_cfg DMA region a different IO region.
 - Reuse everything for MMIO and IOport DMA regions
 - Make transfer status only based on control field
 - Use DMA helpers instead of direct map/unmap
 - Change ARM fw_cfg DMA address space
 - Change Linux boot process to match linuxboot.S
 - Add select capabilities in the FWCfgDmaAccess struct
 - Update documentation to reflect all these changes

[PATCH v3] QEMU fw_cfg DMA interface documentation

[Marc Marí]

Add fw_cfg DMA interface specfication in the fw_cfg documentation.

Signed-off-by: Marc Marí <markmb@redhat.com>
---
 Documentation/devicetree/bindings/arm/fw-cfg.txt | 49 +++++++++++++++++++++++-
 1 file changed, 48 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/arm/fw-cfg.txt b/Documentation/devicetree/bindings/arm/fw-cfg.txt
index 953fb64..ba6945e 100644
--- a/Documentation/devicetree/bindings/arm/fw-cfg.txt
+++ b/Documentation/devicetree/bindings/arm/fw-cfg.txt
@@ -45,6 +45,51 @@ blob to be read from the data register has size 4, and it is to be interpreted
 as a uint32_t value in little endian byte order. The current value
 (corresponding to the above outer protocol) is zero.
 
+If bit 1 of the feature bitmap is set, the DMA interface is present. This
+can be used through the 64-bit wide address register.
+
+The address register is in big-endian format. The value for the register is 0
+at startup and after an operation. A write to the lower half triggers an
+operation. This means, that operations with 32-bit addresses can be triggered
+with just one write, whereas operations with 64-bit addresses can be triggered
+with one 64-bit write or two 32-bit writes, starting with the higher part.
+
+In this register, the physical address of a FWCfgDmaAccess structure in RAM
+should be written. This is the format of the FWCfgDmaAccess structure:
+
+typedef struct FWCfgDmaAccess {
+    uint32_t control;
+    uint32_t length;
+    uint64_t address;
+} FWCfgDmaAccess;
+
+The fields of the structure are in big endian mode, and the field at the lowest
+address is the "control" field.
+
+The "control" field has the following bits:
+ - Bit 0: Error
+ - Bit 1: Read
+ - Bit 2: Skip
+ - Bit 3: Select. The upper 16 bits are the selected index.
+
+When an operation is triggered, if the "control" field has bit 3 set, the
+upper 16 bits are interpreted as an index of a firmware configuration item.
+This has the same effect as writing the selector register.
+
+If the "control" field has bit 1 set, a read operation will be performed.
+"length" bytes for the current selector and offset will be copied into the
+physical RAM address specified by the "address" field.
+
+If the "control" field has bit 2 set (and not bit 1), a skip operation will be
+performed. The offset for the current selector will be advanced "length" bytes.
+
+To check result, read the "control" field:
+   error bit set        ->  something went wrong.
+   all bits cleared     ->  transfer finished successfully.
+   otherwise            ->  transfer still in progress (doesn't happen
+                            today due to implementation not being async,
+                            but may in the future).
+
 The guest kernel is not expected to use these registers (although it is
 certainly allowed to); the device tree bindings are documented here because
 this is where device tree bindings reside in general.
@@ -56,6 +101,8 @@ Required properties:
 - reg: the MMIO region used by the device.
   * Bytes 0x0 to 0x7 cover the data register.
   * Bytes 0x8 to 0x9 cover the selector register.
+  * With DMA interface enabled: Bytes 0xc to 0x13 cover the DMA address
+    register.
   * Further registers may be appended to the region in case of future interface
     revisions / feature bits.
 
@@ -66,7 +113,7 @@ Example:
 	#address-cells = <0x2>;
 
 	fw-cfg@9020000 {
+		reg = <0x0 0x9020000 0x0 0x14>;
 		compatible = "qemu,fw-cfg-mmio";
-		reg = <0x0 0x9020000 0x0 0xa>;
 	};
 };
-- 
2.4.3