From: Javier Martinez Canillas <javier@osg.samsung.com>
To: linux-kernel@vger.kernel.org
Cc: Kukjin Kim <kgene@kernel.org>,
rtc-linux@googlegroups.com, Chanwoo Choi <cw00.choi@samsung.com>,
Alexandre Belloni <alexandre.belloni@free-electrons.com>,
Krzysztof Kozlowski <k.kozlowski@samsung.com>,
Laxman Dewangan <ldewangan@nvidia.com>,
linux-samsung-soc@vger.kernel.org,
Javier Martinez Canillas <javier@osg.samsung.com>
Subject: [PATCH v3 06/10] rtc: max77686: Add max77802 support
Date: Tue, 26 Jan 2016 16:20:16 -0300 [thread overview]
Message-ID: <1453836020-29579-7-git-send-email-javier@osg.samsung.com> (raw)
In-Reply-To: <1453836020-29579-1-git-send-email-javier@osg.samsung.com>
The MAX77686 and MAX77802 RTC IP blocks are very similar with only
these differences:
0) The RTC registers layout and addresses are different.
1) The MAX77686 use 1 bit of the sec/min/hour/etc registers as the
alarm enable while MAX77802 has a separate register for that.
2) The MAX77686 RTCYEAR register valid values range is 0..99 while
for MAX77802 is 0..199.
3) The MAX77686 has a separate I2C address for the RTC registers
while the MAX77802 uses the same I2C address as the PMIC regs.
5) The minimum delay before a RTC update (16 msecs vs 200 usecs).
There are separate drivers for MAX77686 and MAX77802 RTC IP blocks
but the differences are not that big so the driver can be extended
to support both instead of duplicating a lot of code in 2 drivers.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
---
Changes in v3:
- Add Laxman Dewangan's Acked-by tag to patch #6.
Changes in v2:
- Add a MAX77802 prefix to ALARM_ENABLE_VALUE. Suggested by Krzysztof Kozlowski.
- Rename .rtcae to .alarm_enable_reg and .rtcrm to .separate_i2c_addr.
Suggested by Krzysztof Kozlowski.
- Don't use func and LINE in error messages. Suggested by Krzysztof Kozlowski.
- Remove REG_RTC_AE2 since is not used by neither max77686 nor max77802.
- Check if REG_RTC_AE1 has a valid address before accessing it.
drivers/rtc/rtc-max77686.c | 208 +++++++++++++++++++++++++++++++++++----------
1 file changed, 162 insertions(+), 46 deletions(-)
diff --git a/drivers/rtc/rtc-max77686.c b/drivers/rtc/rtc-max77686.c
index 1f501b6fc314..09fc73016d3a 100644
--- a/drivers/rtc/rtc-max77686.c
+++ b/drivers/rtc/rtc-max77686.c
@@ -1,5 +1,5 @@
/*
- * RTC driver for Maxim MAX77686
+ * RTC driver for Maxim MAX77686 and MAX77802
*
* Copyright (C) 2012 Samsung Electronics Co.Ltd
*
@@ -41,6 +41,15 @@
#define ALARM_ENABLE_SHIFT 7
#define ALARM_ENABLE_MASK (1 << ALARM_ENABLE_SHIFT)
+#define REG_RTC_NONE 0xdeadbeef
+
+/*
+ * MAX77802 has separate register (RTCAE1) for alarm enable instead
+ * using 1 bit from registers RTC{SEC,MIN,HOUR,DAY,MONTH,YEAR,DATE}
+ * as in done in MAX77686.
+ */
+#define MAX77802_ALARM_ENABLE_VALUE 0x77
+
enum {
RTC_SEC = 0,
RTC_MIN,
@@ -59,6 +68,10 @@ struct max77686_rtc_driver_data {
u8 mask;
/* Registers offset to I2C addresses map */
const unsigned int *map;
+ /* Has a separate alarm enable register? */
+ bool alarm_enable_reg;
+ /* Has a separate I2C regmap for the RTC? */
+ bool separate_i2c_addr;
};
struct max77686_rtc_info {
@@ -108,6 +121,7 @@ enum max77686_rtc_reg_offset {
REG_ALARM2_MONTH,
REG_ALARM2_YEAR,
REG_ALARM2_DATE,
+ REG_RTC_AE1,
REG_RTC_END,
};
@@ -138,12 +152,52 @@ static const unsigned int max77686_map[REG_RTC_END] = {
[REG_ALARM2_MONTH] = MAX77686_ALARM2_MONTH,
[REG_ALARM2_YEAR] = MAX77686_ALARM2_YEAR,
[REG_ALARM2_DATE] = MAX77686_ALARM2_DATE,
+ [REG_RTC_AE1] = REG_RTC_NONE,
};
static const struct max77686_rtc_driver_data max77686_drv_data = {
.delay = 16000,
.mask = 0x7f,
.map = max77686_map,
+ .alarm_enable_reg = false,
+ .separate_i2c_addr = true,
+};
+
+static const unsigned int max77802_map[REG_RTC_END] = {
+ [REG_RTC_CONTROLM] = MAX77802_RTC_CONTROLM,
+ [REG_RTC_CONTROL] = MAX77802_RTC_CONTROL,
+ [REG_RTC_UPDATE0] = MAX77802_RTC_UPDATE0,
+ [REG_WTSR_SMPL_CNTL] = MAX77802_WTSR_SMPL_CNTL,
+ [REG_RTC_SEC] = MAX77802_RTC_SEC,
+ [REG_RTC_MIN] = MAX77802_RTC_MIN,
+ [REG_RTC_HOUR] = MAX77802_RTC_HOUR,
+ [REG_RTC_WEEKDAY] = MAX77802_RTC_WEEKDAY,
+ [REG_RTC_MONTH] = MAX77802_RTC_MONTH,
+ [REG_RTC_YEAR] = MAX77802_RTC_YEAR,
+ [REG_RTC_DATE] = MAX77802_RTC_DATE,
+ [REG_ALARM1_SEC] = MAX77802_ALARM1_SEC,
+ [REG_ALARM1_MIN] = MAX77802_ALARM1_MIN,
+ [REG_ALARM1_HOUR] = MAX77802_ALARM1_HOUR,
+ [REG_ALARM1_WEEKDAY] = MAX77802_ALARM1_WEEKDAY,
+ [REG_ALARM1_MONTH] = MAX77802_ALARM1_MONTH,
+ [REG_ALARM1_YEAR] = MAX77802_ALARM1_YEAR,
+ [REG_ALARM1_DATE] = MAX77802_ALARM1_DATE,
+ [REG_ALARM2_SEC] = MAX77802_ALARM2_SEC,
+ [REG_ALARM2_MIN] = MAX77802_ALARM2_MIN,
+ [REG_ALARM2_HOUR] = MAX77802_ALARM2_HOUR,
+ [REG_ALARM2_WEEKDAY] = MAX77802_ALARM2_WEEKDAY,
+ [REG_ALARM2_MONTH] = MAX77802_ALARM2_MONTH,
+ [REG_ALARM2_YEAR] = MAX77802_ALARM2_YEAR,
+ [REG_ALARM2_DATE] = MAX77802_ALARM2_DATE,
+ [REG_RTC_AE1] = MAX77802_RTC_AE1,
+};
+
+static const struct max77686_rtc_driver_data max77802_drv_data = {
+ .delay = 200,
+ .mask = 0xff,
+ .map = max77802_map,
+ .alarm_enable_reg = true,
+ .separate_i2c_addr = false,
};
static void max77686_rtc_data_to_tm(u8 *data, struct rtc_time *tm,
@@ -165,12 +219,20 @@ static void max77686_rtc_data_to_tm(u8 *data, struct rtc_time *tm,
tm->tm_wday = ffs(data[RTC_WEEKDAY] & mask) - 1;
tm->tm_mday = data[RTC_DATE] & 0x1f;
tm->tm_mon = (data[RTC_MONTH] & 0x0f) - 1;
- tm->tm_year = (data[RTC_YEAR] & mask) + 100;
+ tm->tm_year = data[RTC_YEAR] & mask;
tm->tm_yday = 0;
tm->tm_isdst = 0;
+
+ /*
+ * MAX77686 uses 1 bit from sec/min/hour/etc RTC registers and the
+ * year values are just 0..99 so add 100 to support up to 2099.
+ */
+ if (!info->drv_data->alarm_enable_reg)
+ tm->tm_year += 100;
}
-static int max77686_rtc_tm_to_data(struct rtc_time *tm, u8 *data)
+static int max77686_rtc_tm_to_data(struct rtc_time *tm, u8 *data,
+ struct max77686_rtc_info *info)
{
data[RTC_SEC] = tm->tm_sec;
data[RTC_MIN] = tm->tm_min;
@@ -178,13 +240,19 @@ static int max77686_rtc_tm_to_data(struct rtc_time *tm, u8 *data)
data[RTC_WEEKDAY] = 1 << tm->tm_wday;
data[RTC_DATE] = tm->tm_mday;
data[RTC_MONTH] = tm->tm_mon + 1;
- data[RTC_YEAR] = tm->tm_year > 100 ? (tm->tm_year - 100) : 0;
- if (tm->tm_year < 100) {
- pr_warn("RTC cannot handle the year %d. Assume it's 2000.\n",
- 1900 + tm->tm_year);
- return -EINVAL;
+ if (!info->drv_data->alarm_enable_reg) {
+ data[RTC_YEAR] = tm->tm_year > 100 ? (tm->tm_year - 100) : 0;
+
+ if (tm->tm_year < 100) {
+ pr_warn("RTC can't handle year %d. Assume it's 2000.\n",
+ 1900 + tm->tm_year);
+ return -EINVAL;
+ }
+ } else {
+ data[RTC_YEAR] = tm->tm_year;
}
+
return 0;
}
@@ -249,7 +317,7 @@ static int max77686_rtc_set_time(struct device *dev, struct rtc_time *tm)
u8 data[RTC_NR_TIME];
int ret;
- ret = max77686_rtc_tm_to_data(tm, data);
+ ret = max77686_rtc_tm_to_data(tm, data, info);
if (ret < 0)
return ret;
@@ -296,11 +364,32 @@ static int max77686_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm)
max77686_rtc_data_to_tm(data, &alrm->time, info);
alrm->enabled = 0;
- for (i = 0; i < ARRAY_SIZE(data); i++) {
- if (data[i] & ALARM_ENABLE_MASK) {
- alrm->enabled = 1;
- break;
+
+ if (!info->drv_data->alarm_enable_reg) {
+ for (i = 0; i < ARRAY_SIZE(data); i++) {
+ if (data[i] & ALARM_ENABLE_MASK) {
+ alrm->enabled = 1;
+ break;
+ }
+ }
+ } else {
+ if (map[REG_RTC_AE1] == REG_RTC_NONE) {
+ ret = -EINVAL;
+ dev_err(info->dev,
+ "alarm enable register not set(%d)\n", ret);
+ goto out;
}
+
+ ret = regmap_read(info->max77686->regmap,
+ map[REG_RTC_AE1], &val);
+ if (ret < 0) {
+ dev_err(info->dev,
+ "fail to read alarm enable(%d)\n", ret);
+ goto out;
+ }
+
+ if (val)
+ alrm->enabled = 1;
}
alrm->pending = 0;
@@ -333,21 +422,36 @@ static int max77686_rtc_stop_alarm(struct max77686_rtc_info *info)
if (ret < 0)
goto out;
- ret = regmap_bulk_read(info->max77686->rtc_regmap,
- map[REG_ALARM1_SEC], data, ARRAY_SIZE(data));
- if (ret < 0) {
- dev_err(info->dev, "%s: fail to read alarm reg(%d)\n",
+ if (!info->drv_data->alarm_enable_reg) {
+ ret = regmap_bulk_read(info->max77686->rtc_regmap,
+ map[REG_ALARM1_SEC], data,
+ ARRAY_SIZE(data));
+ if (ret < 0) {
+ dev_err(info->dev, "%s: fail to read alarm reg(%d)\n",
__func__, ret);
- goto out;
- }
+ goto out;
+ }
- max77686_rtc_data_to_tm(data, &tm, info);
+ max77686_rtc_data_to_tm(data, &tm, info);
- for (i = 0; i < ARRAY_SIZE(data); i++)
- data[i] &= ~ALARM_ENABLE_MASK;
+ for (i = 0; i < ARRAY_SIZE(data); i++)
+ data[i] &= ~ALARM_ENABLE_MASK;
+
+ ret = regmap_bulk_write(info->max77686->rtc_regmap,
+ map[REG_ALARM1_SEC], data,
+ ARRAY_SIZE(data));
+ } else {
+ if (map[REG_RTC_AE1] == REG_RTC_NONE) {
+ ret = -EINVAL;
+ dev_err(info->dev,
+ "alarm enable register not set(%d)\n", ret);
+ goto out;
+ }
+
+ ret = regmap_write(info->max77686->regmap,
+ map[REG_RTC_AE1], 0);
+ }
- ret = regmap_bulk_write(info->max77686->rtc_regmap,
- map[REG_ALARM1_SEC], data, ARRAY_SIZE(data));
if (ret < 0) {
dev_err(info->dev, "%s: fail to write alarm reg(%d)\n",
__func__, ret);
@@ -373,29 +477,37 @@ static int max77686_rtc_start_alarm(struct max77686_rtc_info *info)
if (ret < 0)
goto out;
- ret = regmap_bulk_read(info->max77686->rtc_regmap,
- map[REG_ALARM1_SEC], data, ARRAY_SIZE(data));
- if (ret < 0) {
- dev_err(info->dev, "%s: fail to read alarm reg(%d)\n",
+ if (!info->drv_data->alarm_enable_reg) {
+ ret = regmap_bulk_read(info->max77686->rtc_regmap,
+ map[REG_ALARM1_SEC], data,
+ ARRAY_SIZE(data));
+ if (ret < 0) {
+ dev_err(info->dev, "%s: fail to read alarm reg(%d)\n",
__func__, ret);
- goto out;
- }
-
- max77686_rtc_data_to_tm(data, &tm, info);
+ goto out;
+ }
- data[RTC_SEC] |= (1 << ALARM_ENABLE_SHIFT);
- data[RTC_MIN] |= (1 << ALARM_ENABLE_SHIFT);
- data[RTC_HOUR] |= (1 << ALARM_ENABLE_SHIFT);
- data[RTC_WEEKDAY] &= ~ALARM_ENABLE_MASK;
- if (data[RTC_MONTH] & 0xf)
- data[RTC_MONTH] |= (1 << ALARM_ENABLE_SHIFT);
- if (data[RTC_YEAR] & info->drv_data->mask)
- data[RTC_YEAR] |= (1 << ALARM_ENABLE_SHIFT);
- if (data[RTC_DATE] & 0x1f)
- data[RTC_DATE] |= (1 << ALARM_ENABLE_SHIFT);
+ max77686_rtc_data_to_tm(data, &tm, info);
+
+ data[RTC_SEC] |= (1 << ALARM_ENABLE_SHIFT);
+ data[RTC_MIN] |= (1 << ALARM_ENABLE_SHIFT);
+ data[RTC_HOUR] |= (1 << ALARM_ENABLE_SHIFT);
+ data[RTC_WEEKDAY] &= ~ALARM_ENABLE_MASK;
+ if (data[RTC_MONTH] & 0xf)
+ data[RTC_MONTH] |= (1 << ALARM_ENABLE_SHIFT);
+ if (data[RTC_YEAR] & info->drv_data->mask)
+ data[RTC_YEAR] |= (1 << ALARM_ENABLE_SHIFT);
+ if (data[RTC_DATE] & 0x1f)
+ data[RTC_DATE] |= (1 << ALARM_ENABLE_SHIFT);
+
+ ret = regmap_bulk_write(info->max77686->rtc_regmap,
+ map[REG_ALARM1_SEC], data,
+ ARRAY_SIZE(data));
+ } else {
+ ret = regmap_write(info->max77686->regmap, map[REG_RTC_AE1],
+ MAX77802_ALARM_ENABLE_VALUE);
+ }
- ret = regmap_bulk_write(info->max77686->rtc_regmap,
- map[REG_ALARM1_SEC], data, ARRAY_SIZE(data));
if (ret < 0) {
dev_err(info->dev, "%s: fail to write alarm reg(%d)\n",
__func__, ret);
@@ -413,7 +525,7 @@ static int max77686_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm)
u8 data[RTC_NR_TIME];
int ret;
- ret = max77686_rtc_tm_to_data(&alrm->time, data);
+ ret = max77686_rtc_tm_to_data(&alrm->time, data, info);
if (ret < 0)
return ret;
@@ -524,6 +636,9 @@ static int max77686_rtc_probe(struct platform_device *pdev)
info->drv_data = (const struct max77686_rtc_driver_data *)
id->driver_data;
+ if (!info->drv_data->separate_i2c_addr)
+ info->max77686->rtc_regmap = info->max77686->regmap;
+
platform_set_drvdata(pdev, info);
ret = max77686_rtc_init_reg(info);
@@ -535,7 +650,7 @@ static int max77686_rtc_probe(struct platform_device *pdev)
device_init_wakeup(&pdev->dev, 1);
- info->rtc_dev = devm_rtc_device_register(&pdev->dev, "max77686-rtc",
+ info->rtc_dev = devm_rtc_device_register(&pdev->dev, id->name,
&max77686_rtc_ops, THIS_MODULE);
if (IS_ERR(info->rtc_dev)) {
@@ -598,6 +713,7 @@ static SIMPLE_DEV_PM_OPS(max77686_rtc_pm_ops,
static const struct platform_device_id rtc_id[] = {
{ "max77686-rtc", .driver_data = (kernel_ulong_t)&max77686_drv_data, },
+ { "max77802-rtc", .driver_data = (kernel_ulong_t)&max77802_drv_data, },
{},
};
MODULE_DEVICE_TABLE(platform, rtc_id);
--
2.5.0
next prev parent reply other threads:[~2016-01-26 19:22 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-01-26 19:20 [PATCH v3 00/10] rtc: max77686: Extend driver and add " Javier Martinez Canillas
2016-01-26 19:20 ` [PATCH v3 01/10] rtc: max77686: Fix max77686_rtc_read_alarm() return value Javier Martinez Canillas
2016-01-27 1:19 ` Andi Shyti
2016-01-26 19:20 ` [PATCH v3 02/10] rtc: max77686: Use ARRAY_SIZE() instead of current array length Javier Martinez Canillas
2016-01-27 1:20 ` Andi Shyti
2016-01-26 19:20 ` [PATCH v3 03/10] rtc: max77686: Use usleep_range() instead of msleep() Javier Martinez Canillas
2016-01-27 1:21 ` Andi Shyti
2016-01-26 19:20 ` [PATCH v3 04/10] rtc: max77686: Use a driver data struct instead hard-coded values Javier Martinez Canillas
2016-01-27 1:21 ` Andi Shyti
2016-01-27 1:47 ` Krzysztof Kozlowski
2016-01-26 19:20 ` [PATCH v3 05/10] rtc: max77686: Add an indirection level to access RTC registers Javier Martinez Canillas
2016-01-27 1:53 ` Krzysztof Kozlowski
2016-01-26 19:20 ` Javier Martinez Canillas [this message]
2016-01-27 1:59 ` [PATCH v3 06/10] rtc: max77686: Add max77802 support Krzysztof Kozlowski
2016-01-27 2:24 ` Javier Martinez Canillas
2016-01-27 2:22 ` Andi Shyti
2016-01-26 19:20 ` [PATCH v3 07/10] rtc: max77686: Use dev_warn() instead of pr_warn() Javier Martinez Canillas
2016-01-27 1:22 ` Andi Shyti
2016-01-27 1:53 ` Javier Martinez Canillas
2016-01-27 2:05 ` Krzysztof Kozlowski
2016-01-27 2:20 ` Javier Martinez Canillas
2016-01-27 2:35 ` Andi Shyti
2016-01-27 2:42 ` Javier Martinez Canillas
2016-01-27 2:46 ` Alexandre Belloni
2016-01-27 2:50 ` Javier Martinez Canillas
2016-01-27 2:12 ` Andi Shyti
2016-01-26 19:20 ` [PATCH v3 08/10] rtc: Remove Maxim 77802 driver Javier Martinez Canillas
2016-01-27 1:22 ` Andi Shyti
2016-01-27 2:09 ` Krzysztof Kozlowski
2016-01-26 19:20 ` [PATCH v3 09/10] ARM: exynos_defconfig: Remove MAX77802 RTC Kconfig symbol Javier Martinez Canillas
2016-01-26 19:20 ` [PATCH v3 10/10] ARM: multi_v7_defconfig: " Javier Martinez Canillas
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1453836020-29579-7-git-send-email-javier@osg.samsung.com \
--to=javier@osg.samsung.com \
--cc=alexandre.belloni@free-electrons.com \
--cc=cw00.choi@samsung.com \
--cc=k.kozlowski@samsung.com \
--cc=kgene@kernel.org \
--cc=ldewangan@nvidia.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=rtc-linux@googlegroups.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®