[PATCH v3 1/4] mtd:fsl-quadspi:use the property fields of SPI-NOR

[PATCH v3 1/4] mtd:fsl-quadspi:use the property fields of SPI-NOR

[Yunhui Cui]

We can get the read/write/erase opcode from the spi nor framework
directly. This patch uses the information stored in the SPI-NOR to
remove the hardcode in the fsl_qspi_init_lut().

Signed-off-by: Yunhui Cui <B56489@freescale.com>
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
---
 drivers/mtd/spi-nor/fsl-quadspi.c | 40 ++++++++++++---------------------------
 1 file changed, 12 insertions(+), 28 deletions(-)

diff --git a/drivers/mtd/spi-nor/fsl-quadspi.c b/drivers/mtd/spi-nor/fsl-quadspi.c
index 9ab2b51..517ffe2 100644
--- a/drivers/mtd/spi-nor/fsl-quadspi.c
+++ b/drivers/mtd/spi-nor/fsl-quadspi.c
@@ -373,9 +373,13 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q)
 	void __iomem *base = q->iobase;
 	int rxfifo = q->devtype_data->rxfifo;
 	u32 lut_base;
-	u8 cmd, addrlen, dummy;
 	int i;
 
+	struct spi_nor *nor = &q->nor[0];
+	u8 addrlen = (nor->addr_width == 3) ? ADDR24BIT : ADDR32BIT;
+	u8 read_op = nor->read_opcode;
+	u8 read_dm = nor->read_dummy;
+
 	fsl_qspi_unlock_lut(q);
 
 	/* Clear all the LUT table */
@@ -385,20 +389,10 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q)
 	/* Quad Read */
 	lut_base = SEQID_QUAD_READ * 4;
 
-	if (q->nor_size <= SZ_16M) {
-		cmd = SPINOR_OP_READ_1_1_4;
-		addrlen = ADDR24BIT;
-		dummy = 8;
-	} else {
-		/* use the 4-byte address */
-		cmd = SPINOR_OP_READ_1_1_4;
-		addrlen = ADDR32BIT;
-		dummy = 8;
-	}
-
-	qspi_writel(q, LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen),
+	qspi_writel(q, LUT0(CMD, PAD1, read_op) | LUT1(ADDR, PAD1, addrlen),
 			base + QUADSPI_LUT(lut_base));
-	qspi_writel(q, LUT0(DUMMY, PAD1, dummy) | LUT1(FSL_READ, PAD4, rxfifo),
+	qspi_writel(q, LUT0(DUMMY, PAD1, read_dm) |
+		    LUT1(FSL_READ, PAD4, rxfifo),
 			base + QUADSPI_LUT(lut_base + 1));
 
 	/* Write enable */
@@ -409,16 +403,8 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q)
 	/* Page Program */
 	lut_base = SEQID_PP * 4;
 
-	if (q->nor_size <= SZ_16M) {
-		cmd = SPINOR_OP_PP;
-		addrlen = ADDR24BIT;
-	} else {
-		/* use the 4-byte address */
-		cmd = SPINOR_OP_PP;
-		addrlen = ADDR32BIT;
-	}
-
-	qspi_writel(q, LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen),
+	qspi_writel(q, LUT0(CMD, PAD1, nor->program_opcode) |
+		    LUT1(ADDR, PAD1, addrlen),
 			base + QUADSPI_LUT(lut_base));
 	qspi_writel(q, LUT0(FSL_WRITE, PAD1, 0),
 			base + QUADSPI_LUT(lut_base + 1));
@@ -432,10 +418,8 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q)
 	/* Erase a sector */
 	lut_base = SEQID_SE * 4;
 
-	cmd = q->nor[0].erase_opcode;
-	addrlen = q->nor_size <= SZ_16M ? ADDR24BIT : ADDR32BIT;
-
-	qspi_writel(q, LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen),
+	qspi_writel(q, LUT0(CMD, PAD1, nor->erase_opcode) |
+		    LUT1(ADDR, PAD1, addrlen),
 			base + QUADSPI_LUT(lut_base));
 
 	/* Erase the whole chip */
-- 
2.1.0.27.g96db324

[PATCH v3 2/4] mtd: fsl-quadspi: Rename SEQID_QUAD_READ to SEQID_READ

[Yunhui Cui]

There are some read modes for flash, such as NORMAL, FAST,
QUAD, DDR QUAD. These modes will use the identical lut table base
So rename SEQID_QUAD_READ to SEQID_READ.

Signed-off-by: Yunhui Cui <B56489@freescale.com>
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
---
 drivers/mtd/spi-nor/fsl-quadspi.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/mtd/spi-nor/fsl-quadspi.c b/drivers/mtd/spi-nor/fsl-quadspi.c
index 517ffe2..9861290 100644
--- a/drivers/mtd/spi-nor/fsl-quadspi.c
+++ b/drivers/mtd/spi-nor/fsl-quadspi.c
@@ -193,7 +193,7 @@
 #define QUADSPI_LUT_NUM		64
 
 /* SEQID -- we can have 16 seqids at most. */
-#define SEQID_QUAD_READ		0
+#define SEQID_READ		0
 #define SEQID_WREN		1
 #define SEQID_WRDI		2
 #define SEQID_RDSR		3
@@ -386,8 +386,8 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q)
 	for (i = 0; i < QUADSPI_LUT_NUM; i++)
 		qspi_writel(q, 0, base + QUADSPI_LUT_BASE + i * 4);
 
-	/* Quad Read */
-	lut_base = SEQID_QUAD_READ * 4;
+	/* Read */
+	lut_base = SEQID_READ * 4;
 
 	qspi_writel(q, LUT0(CMD, PAD1, read_op) | LUT1(ADDR, PAD1, addrlen),
 			base + QUADSPI_LUT(lut_base));
@@ -468,7 +468,7 @@ static int fsl_qspi_get_seqid(struct fsl_qspi *q, u8 cmd)
 {
 	switch (cmd) {
 	case SPINOR_OP_READ_1_1_4:
-		return SEQID_QUAD_READ;
+		return SEQID_READ;
 	case SPINOR_OP_WREN:
 		return SEQID_WREN;
 	case SPINOR_OP_WRDI:
-- 
2.1.0.27.g96db324

[PATCH v3 3/4] mtd: spi-nor: fsl-quadspi: add fast-read mode support

[Yunhui Cui]

From: Yunhui Cui <yunhui.cui@nxp.com>

The qspi driver add generic fast-read mode for different
flash venders. There are some different board flash work on
different mode, such fast-read, quad-mode.

Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
---
 drivers/mtd/spi-nor/fsl-quadspi.c | 21 ++++++++++++++++-----
 1 file changed, 16 insertions(+), 5 deletions(-)

diff --git a/drivers/mtd/spi-nor/fsl-quadspi.c b/drivers/mtd/spi-nor/fsl-quadspi.c
index 9861290..09adaa4 100644
--- a/drivers/mtd/spi-nor/fsl-quadspi.c
+++ b/drivers/mtd/spi-nor/fsl-quadspi.c
@@ -389,11 +389,21 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q)
 	/* Read */
 	lut_base = SEQID_READ * 4;
 
-	qspi_writel(q, LUT0(CMD, PAD1, read_op) | LUT1(ADDR, PAD1, addrlen),
-			base + QUADSPI_LUT(lut_base));
-	qspi_writel(q, LUT0(DUMMY, PAD1, read_dm) |
-		    LUT1(FSL_READ, PAD4, rxfifo),
-			base + QUADSPI_LUT(lut_base + 1));
+	if (nor->flash_read == SPI_NOR_FAST) {
+		qspi_writel(q, LUT0(CMD, PAD1, read_op) |
+			    LUT1(ADDR, PAD1, addrlen),
+				base + QUADSPI_LUT(lut_base));
+		qspi_writel(q,  LUT0(DUMMY, PAD1, read_dm) |
+			    LUT1(FSL_READ, PAD1, rxfifo),
+				base + QUADSPI_LUT(lut_base + 1));
+	} else if (nor->flash_read == SPI_NOR_QUAD) {
+		qspi_writel(q, LUT0(CMD, PAD1, read_op) |
+			    LUT1(ADDR, PAD1, addrlen),
+				base + QUADSPI_LUT(lut_base));
+		qspi_writel(q, LUT0(DUMMY, PAD1, read_dm) |
+			    LUT1(FSL_READ, PAD4, rxfifo),
+				base + QUADSPI_LUT(lut_base + 1));
+	}
 
 	/* Write enable */
 	lut_base = SEQID_WREN * 4;
@@ -468,6 +478,7 @@ static int fsl_qspi_get_seqid(struct fsl_qspi *q, u8 cmd)
 {
 	switch (cmd) {
 	case SPINOR_OP_READ_1_1_4:
+	case SPINOR_OP_READ_FAST:
 		return SEQID_READ;
 	case SPINOR_OP_WREN:
 		return SEQID_WREN;
-- 
2.1.0.27.g96db324

[PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW protection

[Yunhui Cui]

From: Yunhui Cui <yunhui.cui@nxp.com>

For Micron family ,The status register write enable/disable bit,
provides hardware data protection for the device.
When the enable/disable bit is set to 1, the status register
nonvolatile bits become read-only and the WRITE STATUS REGISTER
operation will not execute.

Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
---
 drivers/mtd/spi-nor/spi-nor.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index ed0c19c..917f814 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -39,6 +39,7 @@
 
 #define SPI_NOR_MAX_ID_LEN	6
 #define SPI_NOR_MAX_ADDR_WIDTH	4
+#define SPI_NOR_MICRON_WRITE_ENABLE	0x7f
 
 struct flash_info {
 	char		*name;
@@ -1238,6 +1239,14 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
 		write_sr(nor, 0);
 	}
 
+	if (JEDEC_MFR(info) == SNOR_MFR_MICRON) {
+		ret = read_sr(nor);
+		ret &= SPI_NOR_MICRON_WRITE_ENABLE;
+
+		write_enable(nor);
+		write_sr(nor, ret);
+	}
+
 	if (!mtd->name)
 		mtd->name = dev_name(dev);
 	mtd->priv = nor;
-- 
2.1.0.27.g96db324

RE: [PATCH v3 1/4] mtd:fsl-quadspi:use the property fields of SPI-NOR

[Yunhui Cui]

Hi All,

Thanks for your suggestions before.
Could you help me to review this patch set if you are free?

Thanks
Yunhui

-----Original Message-----
From: Yunhui Cui [mailto:B56489@freescale.com] 
Sent: Thursday, March 03, 2016 2:54 PM
To: dwmw2@infradead.org; computersforpeace@gmail.com; han.xu@freescale.com
Cc: linux-kernel@vger.kernel.org; linux-mtd@lists.infradead.org; linux-arm-kernel@lists.infradead.org; Yao Yuan; Yunhui Cui
Subject: [PATCH v3 1/4] mtd:fsl-quadspi:use the property fields of SPI-NOR

We can get the read/write/erase opcode from the spi nor framework directly. This patch uses the information stored in the SPI-NOR to remove the hardcode in the fsl_qspi_init_lut().

Signed-off-by: Yunhui Cui <B56489@freescale.com>
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
---
 drivers/mtd/spi-nor/fsl-quadspi.c | 40 ++++++++++++---------------------------
 1 file changed, 12 insertions(+), 28 deletions(-)

diff --git a/drivers/mtd/spi-nor/fsl-quadspi.c b/drivers/mtd/spi-nor/fsl-quadspi.c
index 9ab2b51..517ffe2 100644
--- a/drivers/mtd/spi-nor/fsl-quadspi.c
+++ b/drivers/mtd/spi-nor/fsl-quadspi.c
@@ -373,9 +373,13 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q)
 	void __iomem *base = q->iobase;
 	int rxfifo = q->devtype_data->rxfifo;
 	u32 lut_base;
-	u8 cmd, addrlen, dummy;
 	int i;
 
+	struct spi_nor *nor = &q->nor[0];
+	u8 addrlen = (nor->addr_width == 3) ? ADDR24BIT : ADDR32BIT;
+	u8 read_op = nor->read_opcode;
+	u8 read_dm = nor->read_dummy;
+
 	fsl_qspi_unlock_lut(q);
 
 	/* Clear all the LUT table */
@@ -385,20 +389,10 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q)
 	/* Quad Read */
 	lut_base = SEQID_QUAD_READ * 4;
 
-	if (q->nor_size <= SZ_16M) {
-		cmd = SPINOR_OP_READ_1_1_4;
-		addrlen = ADDR24BIT;
-		dummy = 8;
-	} else {
-		/* use the 4-byte address */
-		cmd = SPINOR_OP_READ_1_1_4;
-		addrlen = ADDR32BIT;
-		dummy = 8;
-	}
-
-	qspi_writel(q, LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen),
+	qspi_writel(q, LUT0(CMD, PAD1, read_op) | LUT1(ADDR, PAD1, addrlen),
 			base + QUADSPI_LUT(lut_base));
-	qspi_writel(q, LUT0(DUMMY, PAD1, dummy) | LUT1(FSL_READ, PAD4, rxfifo),
+	qspi_writel(q, LUT0(DUMMY, PAD1, read_dm) |
+		    LUT1(FSL_READ, PAD4, rxfifo),
 			base + QUADSPI_LUT(lut_base + 1));
 
 	/* Write enable */
@@ -409,16 +403,8 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q)
 	/* Page Program */
 	lut_base = SEQID_PP * 4;
 
-	if (q->nor_size <= SZ_16M) {
-		cmd = SPINOR_OP_PP;
-		addrlen = ADDR24BIT;
-	} else {
-		/* use the 4-byte address */
-		cmd = SPINOR_OP_PP;
-		addrlen = ADDR32BIT;
-	}
-
-	qspi_writel(q, LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen),
+	qspi_writel(q, LUT0(CMD, PAD1, nor->program_opcode) |
+		    LUT1(ADDR, PAD1, addrlen),
 			base + QUADSPI_LUT(lut_base));
 	qspi_writel(q, LUT0(FSL_WRITE, PAD1, 0),
 			base + QUADSPI_LUT(lut_base + 1));
@@ -432,10 +418,8 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q)
 	/* Erase a sector */
 	lut_base = SEQID_SE * 4;
 
-	cmd = q->nor[0].erase_opcode;
-	addrlen = q->nor_size <= SZ_16M ? ADDR24BIT : ADDR32BIT;
-
-	qspi_writel(q, LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen),
+	qspi_writel(q, LUT0(CMD, PAD1, nor->erase_opcode) |
+		    LUT1(ADDR, PAD1, addrlen),
 			base + QUADSPI_LUT(lut_base));
 
 	/* Erase the whole chip */
--
2.1.0.27.g96db324

Re: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW protection

[Bean Huo 霍斌斌 (beanhuo)]

> From: Yunhui Cui <B56489@freescale.com>
> To: <dwmw2@infradead.org>, <computersforpeace@gmail.com>,
> 	<han.xu@freescale.com>
> Cc: <linux-kernel@vger.kernel.org>, <linux-mtd@lists.infradead.org>,
> 	<linux-arm-kernel@lists.infradead.org>, <yao.yuan@nxp.com>, Yunhui
> Cui
> 	<yunhui.cui@nxp.com>
> Subject: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW
> 	protection
> Message-ID: <1456988044-37061-4-git-send-email-B56489@freescale.com>
> Content-Type: text/plain
> 
> From: Yunhui Cui <yunhui.cui@nxp.com>
> 
> For Micron family ,The status register write enable/disable bit, provides
> hardware data protection for the device.
> When the enable/disable bit is set to 1, the status register nonvolatile bits
> become read-only and the WRITE STATUS REGISTER operation will not
> execute.
> 
> Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
> ---
>  drivers/mtd/spi-nor/spi-nor.c | 9 +++++++++
>  1 file changed, 9 insertions(+)
> 
> diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
> index ed0c19c..917f814 100644
> --- a/drivers/mtd/spi-nor/spi-nor.c
> +++ b/drivers/mtd/spi-nor/spi-nor.c
> @@ -39,6 +39,7 @@
> 
>  #define SPI_NOR_MAX_ID_LEN	6
>  #define SPI_NOR_MAX_ADDR_WIDTH	4
> +#define SPI_NOR_MICRON_WRITE_ENABLE	0x7f
> 
>  struct flash_info {
>  	char		*name;
> @@ -1238,6 +1239,14 @@ int spi_nor_scan(struct spi_nor *nor, const char
> *name, enum read_mode mode)
>  		write_sr(nor, 0);
>  	}
> 
> +	if (JEDEC_MFR(info) == SNOR_MFR_MICRON) {
> +		ret = read_sr(nor);
> +		ret &= SPI_NOR_MICRON_WRITE_ENABLE;
> +
For Micron the status register write enable/disable bit, its default/factory value is disable.
Can here first check ,then program?
> +		write_enable(nor);
> +		write_sr(nor, ret);
> +	}
> +
>  	if (!mtd->name)
>  		mtd->name = dev_name(dev);
>  	mtd->priv = nor;

RE: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW protection

[Yunhui Cui]

Hi Bean,

Thanks for your suggestions very much.
Yes, the flash N25Q128A status register write enable/disable bit is disable in initial state.
But, This patch aims to clear status register bit[7](write enable/disable bit) to 0, which enables the bit.
Frankly speaking, I also don't want to add this patch.
The reason for this is that clear status register bit[7] to 0 is a must to set quad mode to Enhanced Volatile Configuration Register using command SPINOR_OP_WD_EVCR. Otherwise it will output "Micron EVCR Quad bit not clear" in spi-nor.c
I looked up the datasheet, but I really don't find out any connection between status register bit[7](write enable/disable bit) equals 0 and seting quad mode to Enhanced Volatile Configuration Register.

Just as I want to send the issue to Micron team , could you give me some solutions ?


Thanks 
Yunhui

-----Original Message-----
From: Bean Huo 霍斌斌 (beanhuo) [mailto:beanhuo@micron.com] 
Sent: Thursday, March 03, 2016 9:39 PM
To: Yunhui Cui
Cc: linux-mtd@lists.infradead.org; dwmw2@infradead.org; computersforpeace@gmail.com; han.xu@freescale.com; linux-kernel@vger.kernel.org; linux-mtd@lists.infradead.org; linux-arm-kernel@lists.infradead.org; Yao Yuan; Yunhui Cui
Subject: Re: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW protection

> From: Yunhui Cui <B56489@freescale.com>
> To: <dwmw2@infradead.org>, <computersforpeace@gmail.com>,
> 	<han.xu@freescale.com>
> Cc: <linux-kernel@vger.kernel.org>, <linux-mtd@lists.infradead.org>,
> 	<linux-arm-kernel@lists.infradead.org>, <yao.yuan@nxp.com>, Yunhui 
> Cui
> 	<yunhui.cui@nxp.com>
> Subject: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW
> 	protection
> Message-ID: <1456988044-37061-4-git-send-email-B56489@freescale.com>
> Content-Type: text/plain
> 
> From: Yunhui Cui <yunhui.cui@nxp.com>
> 
> For Micron family ,The status register write enable/disable bit, 
> provides hardware data protection for the device.
> When the enable/disable bit is set to 1, the status register 
> nonvolatile bits become read-only and the WRITE STATUS REGISTER 
> operation will not execute.
> 
> Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
> ---
>  drivers/mtd/spi-nor/spi-nor.c | 9 +++++++++
>  1 file changed, 9 insertions(+)
> 
> diff --git a/drivers/mtd/spi-nor/spi-nor.c 
> b/drivers/mtd/spi-nor/spi-nor.c index ed0c19c..917f814 100644
> --- a/drivers/mtd/spi-nor/spi-nor.c
> +++ b/drivers/mtd/spi-nor/spi-nor.c
> @@ -39,6 +39,7 @@
> 
>  #define SPI_NOR_MAX_ID_LEN	6
>  #define SPI_NOR_MAX_ADDR_WIDTH	4
> +#define SPI_NOR_MICRON_WRITE_ENABLE	0x7f
> 
>  struct flash_info {
>  	char		*name;
> @@ -1238,6 +1239,14 @@ int spi_nor_scan(struct spi_nor *nor, const 
> char *name, enum read_mode mode)
>  		write_sr(nor, 0);
>  	}
> 
> +	if (JEDEC_MFR(info) == SNOR_MFR_MICRON) {
> +		ret = read_sr(nor);
> +		ret &= SPI_NOR_MICRON_WRITE_ENABLE;
> +
For Micron the status register write enable/disable bit, its default/factory value is disable.
Can here first check ,then program?
> +		write_enable(nor);
> +		write_sr(nor, ret);
> +	}
> +
>  	if (!mtd->name)
>  		mtd->name = dev_name(dev);
>  	mtd->priv = nor;

RE: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW protection

[Bean Huo 霍斌斌 (beanhuo)]

Hi, Yunhai
You mean that EVCR.bit7 cannot clear(enable quad mode) if not write SR.bit7 to 0?
They don't have any connection each other.

> -----Original Message-----
> From: Yunhui Cui [mailto:yunhui.cui@nxp.com]
> Sent: Friday, March 18, 2016 6:09 PM
> To: Bean Huo 霍斌斌 (beanhuo); Yunhui Cui
> Cc: linux-mtd@lists.infradead.org; dwmw2@infradead.org;
> computersforpeace@gmail.com; han.xu@freescale.com;
> linux-kernel@vger.kernel.org; linux-mtd@lists.infradead.org;
> linux-arm-kernel@lists.infradead.org; Yao Yuan
> Subject: RE: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW protection
> 
> Hi Bean,
> 
> Thanks for your suggestions very much.
> Yes, the flash N25Q128A status register write enable/disable bit is disable in
> initial state.
> But, This patch aims to clear status registerV bit[7](write enable/disable bit) to
> 0, which enables the bit.
> Frankly speaking, I also don't want to add this patch.
> The reason for this is that clear status register bit[7] to 0 is a must to set quad
> mode to Enhanced Volatile Configuration Register using command
> SPINOR_OP_WD_EVCR. Otherwise it will output "Micron EVCR Quad bit not
> clear" in spi-nor.c I looked up the datasheet, but I really don't find out any
> connection between status register bit[7](write enable/disable bit) equals 0
> and seting quad mode to Enhanced Volatile Configuration Register.
> 
> Just as I want to send the issue to Micron team , could you give me some
> solutions ?
> 
> 
> Thanks
> Yunhui
> 
> -----Original Message-----
> From: Bean Huo 霍斌斌 (beanhuo) [mailto:beanhuo@micron.com]
> Sent: Thursday, March 03, 2016 9:39 PM
> To: Yunhui Cui
> Cc: linux-mtd@lists.infradead.org; dwmw2@infradead.org;
> computersforpeace@gmail.com; han.xu@freescale.com;
> linux-kernel@vger.kernel.org; linux-mtd@lists.infradead.org;
> linux-arm-kernel@lists.infradead.org; Yao Yuan; Yunhui Cui
> Subject: Re: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW protection
> 
> > From: Yunhui Cui <B56489@freescale.com>
> > To: <dwmw2@infradead.org>, <computersforpeace@gmail.com>,
> > 	<han.xu@freescale.com>
> > Cc: <linux-kernel@vger.kernel.org>, <linux-mtd@lists.infradead.org>,
> > 	<linux-arm-kernel@lists.infradead.org>, <yao.yuan@nxp.com>, Yunhui
> > Cui
> > 	<yunhui.cui@nxp.com>
> > Subject: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW
> > 	protection
> > Message-ID:
> <1456988044-37061-4-git-send-email-B56489@freescale.com>
> > Content-Type: text/plain
> >
> > From: Yunhui Cui <yunhui.cui@nxp.com>
> >
> > For Micron family ,The status register write enable/disable bit,
> > provides hardware data protection for the device.
> > When the enable/disable bit is set to 1, the status register
> > nonvolatile bits become read-only and the WRITE STATUS REGISTER
> > operation will not execute.
> >
> > Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
> > ---
> >  drivers/mtd/spi-nor/spi-nor.c | 9 +++++++++
> >  1 file changed, 9 insertions(+)
> >
> > diff --git a/drivers/mtd/spi-nor/spi-nor.c
> > b/drivers/mtd/spi-nor/spi-nor.c index ed0c19c..917f814 100644
> > --- a/drivers/mtd/spi-nor/spi-nor.c
> > +++ b/drivers/mtd/spi-nor/spi-nor.c
> > @@ -39,6 +39,7 @@
> >
> >  #define SPI_NOR_MAX_ID_LEN	6
> >  #define SPI_NOR_MAX_ADDR_WIDTH	4
> > +#define SPI_NOR_MICRON_WRITE_ENABLE	0x7f
> >
> >  struct flash_info {
> >  	char		*name;
> > @@ -1238,6 +1239,14 @@ int spi_nor_scan(struct spi_nor *nor, const
> > char *name, enum read_mode mode)
> >  		write_sr(nor, 0);
> >  	}
> >
> > +	if (JEDEC_MFR(info) == SNOR_MFR_MICRON) {
> > +		ret = read_sr(nor);
> > +		ret &= SPI_NOR_MICRON_WRITE_ENABLE;
> > +
> For Micron the status register write enable/disable bit, its default/factory
> value is disable.
> Can here first check ,then program?
> > +		write_enable(nor);
> > +		write_sr(nor, ret);
> > +	}
> > +
> >  	if (!mtd->name)
> >  		mtd->name = dev_name(dev);
> >  	mtd->priv = nor;

RE: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW protection

[Yunhui Cui]

Hi Bean,

I tested with flash N25Q128A again.
In fact, It must output "Micron EVCR Quad bit not clear" in spi-nor.c, if the status register write enable/disable bit is set.

Could you give some suggestions about this ?
Thanks
Yunhui

-----Original Message-----
From: Bean Huo 霍斌斌 (beanhuo) [mailto:beanhuo@micron.com] 
Sent: Monday, March 21, 2016 10:56 AM
To: Yunhui Cui; Yunhui Cui
Cc: linux-mtd@lists.infradead.org; dwmw2@infradead.org; computersforpeace@gmail.com; han.xu@freescale.com; linux-kernel@vger.kernel.org; linux-mtd@lists.infradead.org; linux-arm-kernel@lists.infradead.org; Yao Yuan
Subject: RE: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW protection

Hi, Yunhai
You mean that EVCR.bit7 cannot clear(enable quad mode) if not write SR.bit7 to 0?
They don't have any connection each other.

> -----Original Message-----
> From: Yunhui Cui [mailto:yunhui.cui@nxp.com]
> Sent: Friday, March 18, 2016 6:09 PM
> To: Bean Huo 霍斌斌 (beanhuo); Yunhui Cui
> Cc: linux-mtd@lists.infradead.org; dwmw2@infradead.org; 
> computersforpeace@gmail.com; han.xu@freescale.com; 
> linux-kernel@vger.kernel.org; linux-mtd@lists.infradead.org; 
> linux-arm-kernel@lists.infradead.org; Yao Yuan
> Subject: RE: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW 
> protection
> 
> Hi Bean,
> 
> Thanks for your suggestions very much.
> Yes, the flash N25Q128A status register write enable/disable bit is 
> disable in initial state.
> But, This patch aims to clear status registerV bit[7](write 
> enable/disable bit) to 0, which enables the bit.
> Frankly speaking, I also don't want to add this patch.
> The reason for this is that clear status register bit[7] to 0 is a 
> must to set quad mode to Enhanced Volatile Configuration Register 
> using command SPINOR_OP_WD_EVCR. Otherwise it will output "Micron EVCR 
> Quad bit not clear" in spi-nor.c I looked up the datasheet, but I 
> really don't find out any connection between status register 
> bit[7](write enable/disable bit) equals 0 and seting quad mode to Enhanced Volatile Configuration Register.
> 
> Just as I want to send the issue to Micron team , could you give me 
> some solutions ?
> 
> 
> Thanks
> Yunhui
> 
> -----Original Message-----
> From: Bean Huo 霍斌斌 (beanhuo) [mailto:beanhuo@micron.com]
> Sent: Thursday, March 03, 2016 9:39 PM
> To: Yunhui Cui
> Cc: linux-mtd@lists.infradead.org; dwmw2@infradead.org; 
> computersforpeace@gmail.com; han.xu@freescale.com; 
> linux-kernel@vger.kernel.org; linux-mtd@lists.infradead.org; 
> linux-arm-kernel@lists.infradead.org; Yao Yuan; Yunhui Cui
> Subject: Re: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW 
> protection
> 
> > From: Yunhui Cui <B56489@freescale.com>
> > To: <dwmw2@infradead.org>, <computersforpeace@gmail.com>,
> > 	<han.xu@freescale.com>
> > Cc: <linux-kernel@vger.kernel.org>, <linux-mtd@lists.infradead.org>,
> > 	<linux-arm-kernel@lists.infradead.org>, <yao.yuan@nxp.com>, Yunhui 
> > Cui
> > 	<yunhui.cui@nxp.com>
> > Subject: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW
> > 	protection
> > Message-ID:
> <1456988044-37061-4-git-send-email-B56489@freescale.com>
> > Content-Type: text/plain
> >
> > From: Yunhui Cui <yunhui.cui@nxp.com>
> >
> > For Micron family ,The status register write enable/disable bit, 
> > provides hardware data protection for the device.
> > When the enable/disable bit is set to 1, the status register 
> > nonvolatile bits become read-only and the WRITE STATUS REGISTER 
> > operation will not execute.
> >
> > Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
> > ---
> >  drivers/mtd/spi-nor/spi-nor.c | 9 +++++++++
> >  1 file changed, 9 insertions(+)
> >
> > diff --git a/drivers/mtd/spi-nor/spi-nor.c 
> > b/drivers/mtd/spi-nor/spi-nor.c index ed0c19c..917f814 100644
> > --- a/drivers/mtd/spi-nor/spi-nor.c
> > +++ b/drivers/mtd/spi-nor/spi-nor.c
> > @@ -39,6 +39,7 @@
> >
> >  #define SPI_NOR_MAX_ID_LEN	6
> >  #define SPI_NOR_MAX_ADDR_WIDTH	4
> > +#define SPI_NOR_MICRON_WRITE_ENABLE	0x7f
> >
> >  struct flash_info {
> >  	char		*name;
> > @@ -1238,6 +1239,14 @@ int spi_nor_scan(struct spi_nor *nor, const 
> > char *name, enum read_mode mode)
> >  		write_sr(nor, 0);
> >  	}
> >
> > +	if (JEDEC_MFR(info) == SNOR_MFR_MICRON) {
> > +		ret = read_sr(nor);
> > +		ret &= SPI_NOR_MICRON_WRITE_ENABLE;
> > +
> For Micron the status register write enable/disable bit, its 
> default/factory value is disable.
> Can here first check ,then program?
> > +		write_enable(nor);
> > +		write_sr(nor, ret);
> > +	}
> > +
> >  	if (!mtd->name)
> >  		mtd->name = dev_name(dev);
> >  	mtd->priv = nor;

RE: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW protection

[Yunhui Cui]

Hi all,

I will send another patch set to replace this patch set. This patch set need not be reviewed more, Many thanks! 

Thanks
Yunhui

-----Original Message-----
From: Bean Huo 霍斌斌 (beanhuo) [mailto:beanhuo@micron.com] 
Sent: Monday, March 21, 2016 10:56 AM
To: Yunhui Cui; Yunhui Cui
Cc: linux-mtd@lists.infradead.org; dwmw2@infradead.org; computersforpeace@gmail.com; han.xu@freescale.com; linux-kernel@vger.kernel.org; linux-mtd@lists.infradead.org; linux-arm-kernel@lists.infradead.org; Yao Yuan
Subject: RE: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW protection

Hi, Yunhai
You mean that EVCR.bit7 cannot clear(enable quad mode) if not write SR.bit7 to 0?
They don't have any connection each other.

> -----Original Message-----
> From: Yunhui Cui [mailto:yunhui.cui@nxp.com]
> Sent: Friday, March 18, 2016 6:09 PM
> To: Bean Huo 霍斌斌 (beanhuo); Yunhui Cui
> Cc: linux-mtd@lists.infradead.org; dwmw2@infradead.org; 
> computersforpeace@gmail.com; han.xu@freescale.com; 
> linux-kernel@vger.kernel.org; linux-mtd@lists.infradead.org; 
> linux-arm-kernel@lists.infradead.org; Yao Yuan
> Subject: RE: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW 
> protection
> 
> Hi Bean,
> 
> Thanks for your suggestions very much.
> Yes, the flash N25Q128A status register write enable/disable bit is 
> disable in initial state.
> But, This patch aims to clear status registerV bit[7](write 
> enable/disable bit) to 0, which enables the bit.
> Frankly speaking, I also don't want to add this patch.
> The reason for this is that clear status register bit[7] to 0 is a 
> must to set quad mode to Enhanced Volatile Configuration Register 
> using command SPINOR_OP_WD_EVCR. Otherwise it will output "Micron EVCR 
> Quad bit not clear" in spi-nor.c I looked up the datasheet, but I 
> really don't find out any connection between status register 
> bit[7](write enable/disable bit) equals 0 and seting quad mode to Enhanced Volatile Configuration Register.
> 
> Just as I want to send the issue to Micron team , could you give me 
> some solutions ?
> 
> 
> Thanks
> Yunhui
> 
> -----Original Message-----
> From: Bean Huo 霍斌斌 (beanhuo) [mailto:beanhuo@micron.com]
> Sent: Thursday, March 03, 2016 9:39 PM
> To: Yunhui Cui
> Cc: linux-mtd@lists.infradead.org; dwmw2@infradead.org; 
> computersforpeace@gmail.com; han.xu@freescale.com; 
> linux-kernel@vger.kernel.org; linux-mtd@lists.infradead.org; 
> linux-arm-kernel@lists.infradead.org; Yao Yuan; Yunhui Cui
> Subject: Re: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW 
> protection
> 
> > From: Yunhui Cui <B56489@freescale.com>
> > To: <dwmw2@infradead.org>, <computersforpeace@gmail.com>,
> > 	<han.xu@freescale.com>
> > Cc: <linux-kernel@vger.kernel.org>, <linux-mtd@lists.infradead.org>,
> > 	<linux-arm-kernel@lists.infradead.org>, <yao.yuan@nxp.com>, Yunhui 
> > Cui
> > 	<yunhui.cui@nxp.com>
> > Subject: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW
> > 	protection
> > Message-ID:
> <1456988044-37061-4-git-send-email-B56489@freescale.com>
> > Content-Type: text/plain
> >
> > From: Yunhui Cui <yunhui.cui@nxp.com>
> >
> > For Micron family ,The status register write enable/disable bit, 
> > provides hardware data protection for the device.
> > When the enable/disable bit is set to 1, the status register 
> > nonvolatile bits become read-only and the WRITE STATUS REGISTER 
> > operation will not execute.
> >
> > Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
> > ---
> >  drivers/mtd/spi-nor/spi-nor.c | 9 +++++++++
> >  1 file changed, 9 insertions(+)
> >
> > diff --git a/drivers/mtd/spi-nor/spi-nor.c 
> > b/drivers/mtd/spi-nor/spi-nor.c index ed0c19c..917f814 100644
> > --- a/drivers/mtd/spi-nor/spi-nor.c
> > +++ b/drivers/mtd/spi-nor/spi-nor.c
> > @@ -39,6 +39,7 @@
> >
> >  #define SPI_NOR_MAX_ID_LEN	6
> >  #define SPI_NOR_MAX_ADDR_WIDTH	4
> > +#define SPI_NOR_MICRON_WRITE_ENABLE	0x7f
> >
> >  struct flash_info {
> >  	char		*name;
> > @@ -1238,6 +1239,14 @@ int spi_nor_scan(struct spi_nor *nor, const 
> > char *name, enum read_mode mode)
> >  		write_sr(nor, 0);
> >  	}
> >
> > +	if (JEDEC_MFR(info) == SNOR_MFR_MICRON) {
> > +		ret = read_sr(nor);
> > +		ret &= SPI_NOR_MICRON_WRITE_ENABLE;
> > +
> For Micron the status register write enable/disable bit, its 
> default/factory value is disable.
> Can here first check ,then program?
> > +		write_enable(nor);
> > +		write_sr(nor, ret);
> > +	}
> > +
> >  	if (!mtd->name)
> >  		mtd->name = dev_name(dev);
> >  	mtd->priv = nor;