From: "Lothar Waßmann" <LW@KARO-electronics.de>
To: Dan Williams <dan.j.williams@intel.com>,
Ian Campbell <ijc+devicetree@hellion.org.uk>,
Kumar Gala <galak@codeaurora.org>,
Mark Rutland <mark.rutland@arm.com>,
Pawel Moll <pawel.moll@arm.com>, Rob Herring <robh+dt@kernel.org>,
Russell King <linux@arm.linux.org.uk>,
Sascha Hauer <kernel@pengutronix.de>,
Shawn Guo <shawnguo@kernel.org>,
Vinod Koul <vinod.koul@intel.com>,
devicetree@vger.kernel.org, dmaengine@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Cc: "Lothar Waßmann" <LW@KARO-electronics.de>
Subject: [PATCHv2 3/8] ARM: dts: imx6-tx6: remove regulator bus
Date: Tue, 8 Mar 2016 09:03:59 +0100 [thread overview]
Message-ID: <1457424244-14549-4-git-send-email-LW@KARO-electronics.de> (raw)
In-Reply-To: <1457424244-14549-1-git-send-email-LW@KARO-electronics.de>
DT maintainers don't like the 'simple-bus' container around the
regulator nodes. So remove it.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6qdl-tx6.dtsi | 178 +++++++++++++++++--------------------
1 file changed, 81 insertions(+), 97 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
index 912f284..ec374f5 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
@@ -97,104 +97,88 @@
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
+ reg_3v3_etn: reg-3v3-etn {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3_ETN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_etnphy_power>;
+ gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
- reg_3v3_etn: regulator@0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "3V3_ETN";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_etnphy_power>;
- gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- reg_2v5: regulator@1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "2V5";
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <2500000>;
- regulator-always-on;
- };
-
- reg_3v3: regulator@2 {
- compatible = "regulator-fixed";
- reg = <2>;
- regulator-name = "3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- reg_can_xcvr: regulator@3 {
- compatible = "regulator-fixed";
- reg = <3>;
- regulator-name = "CAN XCVR";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_flexcan_xcvr>;
- gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
- enable-active-low;
- };
-
- reg_lcd0_pwr: regulator@4 {
- compatible = "regulator-fixed";
- reg = <4>;
- regulator-name = "LCD0 POWER";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_lcd0_pwr>;
- gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_lcd1_pwr: regulator@5 {
- compatible = "regulator-fixed";
- reg = <5>;
- regulator-name = "LCD1 POWER";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_lcd1_pwr>;
- gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_usbh1_vbus: regulator@6 {
- compatible = "regulator-fixed";
- reg = <6>;
- regulator-name = "usbh1_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbh1_vbus>;
- gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- reg_usbotg_vbus: regulator@7 {
- compatible = "regulator-fixed";
- reg = <7>;
- regulator-name = "usbotg_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg_vbus>;
- gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
+ reg_2v5: reg-2v5 {
+ compatible = "regulator-fixed";
+ regulator-name = "2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ reg_3v3: reg-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_can_xcvr: reg-can-xcvr {
+ compatible = "regulator-fixed";
+ regulator-name = "CAN XCVR";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan_xcvr>;
+ gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
+ enable-active-low;
+ };
+
+ reg_lcd0_pwr: reg-lcd0-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD0 POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd0_pwr>;
+ gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ reg_lcd1_pwr: reg-lcd1-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD1 POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd1_pwr>;
+ gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ reg_usbh1_vbus: reg-usbh1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_vbus>;
+ gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usbotg_vbus: reg-usbotg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbotg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg_vbus>;
+ gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
};
sound {
--
2.1.4
next prev parent reply other threads:[~2016-03-08 8:07 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-03-08 8:03 [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
2016-03-08 8:03 ` [PATCHv2 1/8] ARM: dts: imx6-tx6: Relicense the Ka-Ro DT files under GPLv2/X11 Lothar Waßmann
2016-03-08 8:03 ` [PATCHv2 2/8] ARM: dts: imx6-tx6: cleanup; no functional change Lothar Waßmann
2016-03-08 8:03 ` Lothar Waßmann [this message]
2016-03-31 6:00 ` [PATCHv2 3/8] ARM: dts: imx6-tx6: remove regulator bus Shawn Guo
2016-03-08 8:04 ` [PATCHv2 4/8] ARM: dts: imx6-tx6: disable the spi node by default Lothar Waßmann
2016-03-08 8:04 ` [PATCHv2 5/8] ARM: dts: imx6-tx6: remove container node around pinctrl nodes Lothar Waßmann
2016-03-08 8:04 ` [PATCHv2 6/8] ARM: dts: imx6qdl-tx6: add mdio node for ethernet phy Lothar Waßmann
2016-03-08 8:04 ` [PATCHv2 7/8] ARM: dts: imx6: add support for more Ka-Ro electronics modules Lothar Waßmann
2016-03-31 6:10 ` Shawn Guo
2016-03-31 6:29 ` Lothar Waßmann
2016-03-31 7:47 ` Shawn Guo
2016-03-08 8:04 ` [PATCHv2 8/8] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard Lothar Waßmann
2016-03-31 6:14 ` [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Shawn Guo
2016-03-31 12:33 ` [PATCHv3 0/5] " Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 1/5] ARM: dts: imx6-tx6: remove regulator bus Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 2/5] ARM: dts: imx6-tx6: remove LED pinctrl setting from hoggrp Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 3/5] ARM: dts: imx6-tx6: enable support for rtscts on UARTs Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 4/5] ARM: dts: imx6: add support for more Ka-Ro electronics modules Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 5/5] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard Lothar Waßmann
2016-04-11 13:57 ` [PATCHv3 0/5] ARM: dts: update Ka-Ro i.MX6 module support Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1457424244-14549-4-git-send-email-LW@KARO-electronics.de \
--to=lw@karo-electronics.de \
--cc=dan.j.williams@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=dmaengine@vger.kernel.org \
--cc=galak@codeaurora.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@arm.linux.org.uk \
--cc=mark.rutland@arm.com \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
--cc=vinod.koul@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®