From: "Lothar Waßmann" <LW@KARO-electronics.de>
To: Shawn Guo <shawnguo@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>,
Ian Campbell <ijc+devicetree@hellion.org.uk>,
Kumar Gala <galak@codeaurora.org>,
Mark Rutland <mark.rutland@arm.com>,
Pawel Moll <pawel.moll@arm.com>, Rob Herring <robh+dt@kernel.org>,
Russell King <linux@arm.linux.org.uk>,
Sascha Hauer <kernel@pengutronix.de>,
Vinod Koul <vinod.koul@intel.com>,
devicetree@vger.kernel.org, dmaengine@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCHv2 7/8] ARM: dts: imx6: add support for more Ka-Ro electronics modules
Date: Thu, 31 Mar 2016 08:29:44 +0200 [thread overview]
Message-ID: <20160331082944.3f604423@ipc1.ka-ro> (raw)
In-Reply-To: <20160331061023.GO28207@tiger>
Hi,
On Thu, 31 Mar 2016 14:10:23 +0800 Shawn Guo wrote:
> On Tue, Mar 08, 2016 at 09:04:03AM +0100, Lothar Waßmann wrote:
> > Add support for the following i.MX6 based modules from Ka-Ro
> > electronics GmbH:
> > TX6S-8034:
> > Processor Freescale i.MX 6 Solo, 800MHz
> > RAM 256MiB DDR3 SDRAM
> > ROM 128MiB NAND Flash
> > Power supply Single 3.1V to 5.5V
> > Size 31mm SO-DIMM
> > Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
> >
> > TX6S-8035:
> > Processor Freescale i.MX 6 Solo, 800MHz
> > RAM 512MiB DDR3 SDRAM
> > ROM 4GiB eMMC
> > Power supply Single 3.1V to 5.5V
> > Size 31mm SO-DIMM
> > Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
> >
> > TX6U-8033:
> > Processor Freescale i.MX 6 Dual Lite, 800MHz
> > RAM 1GiB DDR3 SDRAM
> > ROM 4GiB eMMC
> > Power supply Single 3.1V to 5.5V
> > Size 31mm SO-DIMM
> > Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
> >
> > TX6Q-1036:
> > Processor Freescale i.MX 6Quad, 1GHz
> > RAM 1GB DDR3 SDRAM 64-bit
> > ROM 8GiB eMMC
> > Power supply Single 3.1V to 5.5V
> > Size 31mm SO-DIMM
> > Temp. Range Extended Consumer Grade (-20°C to 105°C Tj)
> >
> > Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
> > ---
> > arch/arm/boot/dts/Makefile | 4 +
> > arch/arm/boot/dts/imx6dl-tx6s-8034.dts | 249 ++++++++++++++++++++++++++++
> > arch/arm/boot/dts/imx6dl-tx6s-8035.dts | 246 +++++++++++++++++++++++++++
> > arch/arm/boot/dts/imx6dl-tx6u-8033.dts | 248 +++++++++++++++++++++++++++
> > arch/arm/boot/dts/imx6q-tx6q-1036.dts | 295 +++++++++++++++++++++++++++++++++
> > 5 files changed, 1042 insertions(+)
> > create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8034.dts
> > create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8035.dts
> > create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-8033.dts
> > create mode 100644 arch/arm/boot/dts/imx6q-tx6q-1036.dts
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index 072294f..71b5cd3 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -320,6 +320,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > imx6dl-sabrelite.dtb \
> > imx6dl-sabresd.dtb \
> > imx6dl-tx6dl-comtft.dtb \
> > + imx6dl-tx6s-8034.dtb \
> > + imx6dl-tx6s-8035.dtb \
> > + imx6dl-tx6u-8033.dtb \
>
> imx6dl-tx6u-8033.dtb should go after imx6dl-tx6u-801x.dtb?
>
Of course. I obviously missed this when dropping the patch to rename
the dtb files which you rejected.
NB: There is no need to quote the full original mail when you have no
further comments on the remaining part. This would save people
from having to scroll through the mail needlessly looking for further
comments.
Lothar Waßmann
next prev parent reply other threads:[~2016-03-31 6:30 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-03-08 8:03 [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
2016-03-08 8:03 ` [PATCHv2 1/8] ARM: dts: imx6-tx6: Relicense the Ka-Ro DT files under GPLv2/X11 Lothar Waßmann
2016-03-08 8:03 ` [PATCHv2 2/8] ARM: dts: imx6-tx6: cleanup; no functional change Lothar Waßmann
2016-03-08 8:03 ` [PATCHv2 3/8] ARM: dts: imx6-tx6: remove regulator bus Lothar Waßmann
2016-03-31 6:00 ` Shawn Guo
2016-03-08 8:04 ` [PATCHv2 4/8] ARM: dts: imx6-tx6: disable the spi node by default Lothar Waßmann
2016-03-08 8:04 ` [PATCHv2 5/8] ARM: dts: imx6-tx6: remove container node around pinctrl nodes Lothar Waßmann
2016-03-08 8:04 ` [PATCHv2 6/8] ARM: dts: imx6qdl-tx6: add mdio node for ethernet phy Lothar Waßmann
2016-03-08 8:04 ` [PATCHv2 7/8] ARM: dts: imx6: add support for more Ka-Ro electronics modules Lothar Waßmann
2016-03-31 6:10 ` Shawn Guo
2016-03-31 6:29 ` Lothar Waßmann [this message]
2016-03-31 7:47 ` Shawn Guo
2016-03-08 8:04 ` [PATCHv2 8/8] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard Lothar Waßmann
2016-03-31 6:14 ` [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Shawn Guo
2016-03-31 12:33 ` [PATCHv3 0/5] " Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 1/5] ARM: dts: imx6-tx6: remove regulator bus Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 2/5] ARM: dts: imx6-tx6: remove LED pinctrl setting from hoggrp Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 3/5] ARM: dts: imx6-tx6: enable support for rtscts on UARTs Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 4/5] ARM: dts: imx6: add support for more Ka-Ro electronics modules Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 5/5] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard Lothar Waßmann
2016-04-11 13:57 ` [PATCHv3 0/5] ARM: dts: update Ka-Ro i.MX6 module support Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160331082944.3f604423@ipc1.ka-ro \
--to=lw@karo-electronics.de \
--cc=dan.j.williams@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=dmaengine@vger.kernel.org \
--cc=galak@codeaurora.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@arm.linux.org.uk \
--cc=mark.rutland@arm.com \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
--cc=vinod.koul@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®