[PATCH 1/4] dt-bindings: Add Japan Display Inc vendor id

[PATCH 1/4] dt-bindings: Add Japan Display Inc vendor id

[Vinay Simha BN]

Add vendor id for Japan Display Inc.

Cc: Archit Taneja <archit.taneja@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index ecc8cf4..1b134f3 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -138,6 +138,7 @@ invensense	InvenSense Inc.
 isee	ISEE 2007 S.L.
 isil	Intersil
 issi	Integrated Silicon Solutions Inc.
+jdi	Japan Display Inc.
 jedec	JEDEC Solid State Technology Association
 karo	Ka-Ro electronics GmbH
 keymile	Keymile GmbH
-- 
1.9.1

[PATCH v2 2/4] dt-bindings: Add jdi lt070me05000 panel bindings

[Vinay Simha BN]

Add documentation for lt070me05000 panel

Cc: Archit Taneja <archit.taneja@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>

---
v2:
 * incorporated rob herring and thierry reviews
   gpio to gpios, gpio to regulator using fixed regulators
   and pwm backlight is removed, since it is controlled by
   dcs commands
---
 .../bindings/display/panel/jdi,lt070me05000.txt    | 57 ++++++++++++++++++++++
 1 file changed, 57 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt

diff --git a/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
new file mode 100644
index 0000000..613b76f
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
@@ -0,0 +1,57 @@
+JDI model LT070ME05000 1200x1920 7" DSI Panel
+
+Required properties:
+- compatible: should be "jdi,lt070me05000"
+- vddp-supply: phandle of the regulator that provides the supply voltage
+  Power IC supply (3-5V)
+- dcdc_en-supply: phandle of the regulator that provides the supply voltage
+  Power IC supply enable, High active
+- vcc-supply: phandle of the regulator that provides the supply voltage
+  IOVCC , power supply for LCM (1.8V)
+- reset-gpios: phandle of gpio for reset line
+  This should be 8mA, gpio can be configured using mux, pinctrl, pinctrl-names
+  XRES, Reset, Low active
+- enable-gpios: phandle of gpio for enable line
+  LED_EN, LED backlight enable, High active
+
+Example:
+
+	vcc_1p8v: regulator-fixed@2 {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-name = "vcc_1p8v";
+		regulator-type = "voltage";
+		startup-delay-us = <0>;
+		gpio = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	tlmm_pinmux: pinctrl@800000 {
+
+		dsi_panel_pinctrl: dsi-panel-pinctrl {
+			mux {
+				pins = "gpio54";
+				function = "gpio";
+				bias-pull-up;
+				drive-strength = <8>;
+			};
+		};
+	};
+
+	dsi0: qcom,mdss_dsi@4700000 {
+		panel@0 {
+			compatible = "jdi,lt070me05000";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&dsi_panel_pinctrl>;
+
+			vddp-supply = <&pm8921_l17>;
+			dcdc_en-supply = <&pm8921_lvs7>;
+			vcc-supply = <&vcc_1p8v>;
+
+			reset-gpios = <&tlmm_pinmux 54 0>;
+			enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
+		};
+	};
-- 
1.9.1

[PATCH v2 3/4] drm/dsi: Implement dcs set/get display brightness

[Vinay Simha BN]

Provide a small convenience wrapper that set/get the
display brightness value

Cc: John Stultz <john.stultz@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Archit Taneja <archit.taneja@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>

---
v1:
 *tested in nexus7 2nd gen.

v2:
 * implemented jani review comments
   -functions name mapped accordingly
   -bl value increased from 0xff to 0xffff
   -backlight interface will be handled in panel driver,
    so it is moved from the mipi_dsi helper function
---
 drivers/gpu/drm/drm_mipi_dsi.c | 49 ++++++++++++++++++++++++++++++++++++++++++
 include/drm/drm_mipi_dsi.h     |  4 ++++
 2 files changed, 53 insertions(+)

diff --git a/drivers/gpu/drm/drm_mipi_dsi.c b/drivers/gpu/drm/drm_mipi_dsi.c
index af0d471..7c22f64 100644
--- a/drivers/gpu/drm/drm_mipi_dsi.c
+++ b/drivers/gpu/drm/drm_mipi_dsi.c
@@ -1041,6 +1041,55 @@ int mipi_dsi_dcs_set_pixel_format(struct mipi_dsi_device *dsi, u8 format)
 }
 EXPORT_SYMBOL(mipi_dsi_dcs_set_pixel_format);
 
+/**
+ * mipi_dsi_dcs_get_display_brightness() - gets the current brightness value
+ * of the display
+ * @dsi: DSI peripheral device
+ * @brightness: brightness value
+ *
+ * Return: 0 on success or a negative error code on failure.
+ */
+int mipi_dsi_dcs_get_display_brightness(struct mipi_dsi_device *dsi,
+					u16 *brightness)
+{
+	ssize_t err;
+
+	err = mipi_dsi_dcs_read(dsi, MIPI_DCS_GET_DISPLAY_BRIGHTNESS,
+				brightness, sizeof(*brightness));
+	if (err < 0) {
+		if (err == 0)
+			err = -ENODATA;
+
+		return err;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL(mipi_dsi_dcs_get_display_brightness);
+
+/**
+ * mipi_dsi_dcs_set_display_brightness() - sets the brightness value of
+ * the display
+ * @dsi: DSI peripheral device
+ * @brightness: brightness value
+ *
+ * Return: 0 on success or a negative error code on failure.
+ */
+int mipi_dsi_dcs_set_display_brightness(struct mipi_dsi_device *dsi,
+					u16 brightness)
+{
+	ssize_t err;
+	u8 bl_value[2] = { brightness & 0xff, brightness >> 8 };
+
+	err = mipi_dsi_dcs_write(dsi, MIPI_DCS_SET_DISPLAY_BRIGHTNESS,
+				 bl_value, sizeof(bl_value));
+	if (err < 0)
+		return err;
+
+	return 0;
+}
+EXPORT_SYMBOL(mipi_dsi_dcs_set_display_brightness);
+
 static int mipi_dsi_drv_probe(struct device *dev)
 {
 	struct mipi_dsi_driver *drv = to_mipi_dsi_driver(dev->driver);
diff --git a/include/drm/drm_mipi_dsi.h b/include/drm/drm_mipi_dsi.h
index 47ac925..404c373 100644
--- a/include/drm/drm_mipi_dsi.h
+++ b/include/drm/drm_mipi_dsi.h
@@ -270,6 +270,10 @@ int mipi_dsi_dcs_set_tear_off(struct mipi_dsi_device *dsi);
 int mipi_dsi_dcs_set_tear_on(struct mipi_dsi_device *dsi,
 			     enum mipi_dsi_dcs_tear_mode mode);
 int mipi_dsi_dcs_set_pixel_format(struct mipi_dsi_device *dsi, u8 format);
+int mipi_dsi_dcs_get_display_brightness(struct mipi_dsi_device *dsi,
+					u16 *brightness);
+int mipi_dsi_dcs_set_display_brightness(struct mipi_dsi_device *dsi,
+					u16 brightness);
 
 /**
  * struct mipi_dsi_driver - DSI driver
-- 
1.9.1

[PATCH v8 4/4] drm/panel: Add JDI LT070ME05000 WUXGA DSI Panel

[Vinay Simha BN]

Add support for the JDI LT070ME05000 WUXGA DSI panel used in
Nexus 7 2013 devices.

Programming sequence for the panel is was originally found in the
android-msm-flo-3.4-lollipop-release branch from:
    https://android.googlesource.com/kernel/msm.git

And video mode setting is from dsi-panel-jdi-dualmipi1-video.dtsi
file in:
    git://codeaurora.org/kernel/msm-3.10.git  LNX.LA.3.6_rb1.27

Cc: Archit Taneja <archit.taneja@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>

---
v1:
 * sumit ported to drm/panel framework, john cherry-picked to mainline,
   folded down other fixes from Vinay and Archit, vinay removed interface
   setting cmd mode, video mode panel selected

v2:
 * incorporated code reviews from theiry, archit
   code style, alphabetical soring in Makefile, Kconfig, regulator_bulk,
   arrays of u8, generic helper function, documentation bindings,

v3:
 * dcs backlight support added
 * tested this panel driver in nexus7 2013 device

v4:
 * backlight interface added in the panel driver
 * incorporated width_mm and height_mm suggested by rob herring

v5:
 * theirry review comments incorporated
   panel model naming consistent, alphabetical soring in Kconfig
   Makefile, MAX_BRIGHTNESS dropped, regulator_names, parameterize
   panel width and height, descprition for control display, cabc
   and interface setting, temporary variable removed, consistent
   error reporting and commit message
 * removed tear on/off, scanline, since these are required only
   for command mode panels

v6:
 * emil review comments incorporated
   PANEL_NUM_REGULATORS dropped, return ret added at necessary
   places, if checks dropped for backlight and gpios

v7:
 * emil review comments incorporated
   added ARRAY_SIZE in struct, regulator_bulk_disable in poweroff,
   gpios checks dropped.
   some returns cannot be dropped, since drm panel framework return
   type required.

v8:
 * emil review commnets incorporated for jdi_panel_unprepare,
   dropped the returns (ref: panel-sharp-lq101r1sx01.c) and
   for jdi_panel_prepare(panel_on) it does not return prematurely
   and goes to poweroff if not success
 * few dev_err's for panel_init
---
 drivers/gpu/drm/panel/Kconfig                  |  11 +
 drivers/gpu/drm/panel/Makefile                 |   1 +
 drivers/gpu/drm/panel/panel-jdi-lt070me05000.c | 518 +++++++++++++++++++++++++
 3 files changed, 530 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-jdi-lt070me05000.c

diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index 1500ab9..62aba97 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -18,6 +18,17 @@ config DRM_PANEL_SIMPLE
 	  that it can be automatically turned off when the panel goes into a
 	  low power state.
 
+config DRM_PANEL_JDI_LT070ME05000
+	tristate "JDI LT070ME05000 WUXGA DSI panel"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	depends on BACKLIGHT_CLASS_DEVICE
+	help
+	  Say Y here if you want to enable support for JDI DSI video mode
+	  panel as found in Google Nexus 7 (2013) devices.
+	  The panel has a 1200(RGB)×1920 (WUXGA) resolution and uses
+	  24 bit per pixel.
+
 config DRM_PANEL_SAMSUNG_LD9040
 	tristate "Samsung LD9040 RGB/SPI panel"
 	depends on OF && SPI
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index f277eed..a5c7ec0 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -1,4 +1,5 @@
 obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
+obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
 obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o
 obj-$(CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00) += panel-panasonic-vvx10f034n00.o
 obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o
diff --git a/drivers/gpu/drm/panel/panel-jdi-lt070me05000.c b/drivers/gpu/drm/panel/panel-jdi-lt070me05000.c
new file mode 100644
index 0000000..d54c472
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-jdi-lt070me05000.c
@@ -0,0 +1,518 @@
+/*
+ * Copyright (C) 2016 InforceComputing
+ * Author: Vinay Simha BN <simhavcs@gmail.com>
+ *
+ * Copyright (C) 2016 Linaro Ltd
+ * Author: Sumit Semwal <sumit.semwal@linaro.org>
+ *
+ * From internet archives, the panel for Nexus 7 2nd Gen, 2013 model is a
+ * JDI model LT070ME05000, and its data sheet is at:
+ * http://panelone.net/en/7-0-inch/JDI_LT070ME05000_7.0_inch-datasheet
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/backlight.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regulator/consumer.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_panel.h>
+
+#include <video/mipi_display.h>
+
+static const char * const regulator_names[] = {
+	"vddp",
+	"dcdc_en",
+	"vcc"
+};
+
+struct jdi_panel {
+	struct drm_panel base;
+	struct mipi_dsi_device *dsi;
+
+	struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
+
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *enable_gpio;
+	struct backlight_device *backlight;
+
+	bool prepared;
+	bool enabled;
+
+	const struct drm_display_mode *mode;
+};
+
+static inline struct jdi_panel *to_jdi_panel(struct drm_panel *panel)
+{
+	return container_of(panel, struct jdi_panel, base);
+}
+
+static int jdi_panel_init(struct jdi_panel *jdi)
+{
+	struct mipi_dsi_device *dsi = jdi->dsi;
+	struct device *dev = &jdi->dsi->dev;
+	int ret;
+
+	dsi->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	ret = mipi_dsi_dcs_soft_reset(dsi);
+	if (ret < 0)
+		return ret;
+
+	usleep_range(10000, 20000);
+
+	ret = mipi_dsi_dcs_set_pixel_format(dsi, MIPI_DCS_PIXEL_FMT_24BIT << 4);
+	if (ret < 0) {
+		dev_err(dev, "failed to set pixel format: %d\n", ret);
+		return ret;
+	}
+
+	ret = mipi_dsi_dcs_set_column_address(dsi, 0, jdi->mode->hdisplay - 1);
+	if (ret < 0) {
+		dev_err(dev, "failed to set column address: %d\n", ret);
+		return ret;
+	}
+
+	ret = mipi_dsi_dcs_set_page_address(dsi, 0, jdi->mode->vdisplay - 1);
+	if (ret < 0) {
+		dev_err(dev, "failed to set page address: %d\n", ret);
+		return ret;
+	}
+
+	/*
+	 * BIT(5) BCTRL = 1 Backlight Control Block On, Brightness registers
+	 *                  are active
+	 * BIT(3) BL = 1    Backlight Control On
+	 * BIT(2) DD = 0    Display Dimming is Off
+	 */
+	ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_WRITE_CONTROL_DISPLAY,
+				 (u8[]){ 0x24 }, 1);
+	if (ret < 0) {
+		dev_err(dev, "failed to write control display: %d\n", ret);
+		return ret;
+	}
+
+	/* CABC off */
+	ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_WRITE_POWER_SAVE,
+				 (u8[]){ 0x00 }, 1);
+	if (ret < 0) {
+		dev_err(dev, "failed to set cabc off: %d\n", ret);
+		return ret;
+	}
+
+	ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
+	if (ret < 0) {
+		dev_err(dev, "failed to set exit sleep mode: %d\n", ret);
+		return ret;
+	}
+
+	msleep(120);
+
+	ret = mipi_dsi_generic_write(dsi, (u8[]){0xB0, 0x00}, 2);
+	if (ret < 0) {
+		dev_err(dev, "failed to set mcap: %d\n", ret);
+		return ret;
+	}
+
+	mdelay(10);
+
+	/* Interface setting, video mode */
+	ret = mipi_dsi_generic_write(dsi, (u8[])
+				     {0xB3, 0x26, 0x08, 0x00, 0x20, 0x00}, 6);
+	if (ret < 0) {
+		dev_err(dev, "failed to set display interface setting: %d\n"
+			, ret);
+		return ret;
+	}
+
+	mdelay(20);
+
+	ret = mipi_dsi_generic_write(dsi, (u8[]){0xB0, 0x03}, 2);
+	if (ret < 0) {
+		dev_err(dev, "failed to set default values for mcap: %d\n"
+			, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int jdi_panel_on(struct jdi_panel *jdi)
+{
+	struct mipi_dsi_device *dsi = jdi->dsi;
+	struct device *dev = &jdi->dsi->dev;
+	int ret;
+
+	dsi->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	ret = mipi_dsi_dcs_set_display_on(dsi);
+	if (ret < 0)
+		dev_err(dev, "failed to set display on: %d\n", ret);
+
+	return ret;
+}
+
+static void jdi_panel_off(struct jdi_panel *jdi)
+{
+	struct mipi_dsi_device *dsi = jdi->dsi;
+	struct device *dev = &jdi->dsi->dev;
+	int ret;
+
+	dsi->mode_flags &= ~MIPI_DSI_MODE_LPM;
+
+	ret = mipi_dsi_dcs_set_display_off(dsi);
+	if (ret < 0)
+		dev_err(dev, "failed to set display off: %d\n", ret);
+
+	ret = mipi_dsi_dcs_enter_sleep_mode(dsi);
+	if (ret < 0)
+		dev_err(dev, "failed to enter sleep mode: %d\n", ret);
+
+	msleep(100);
+}
+
+static int jdi_panel_disable(struct drm_panel *panel)
+{
+	struct jdi_panel *jdi = to_jdi_panel(panel);
+
+	if (!jdi->enabled)
+		return 0;
+
+	jdi->backlight->props.power = FB_BLANK_POWERDOWN;
+	backlight_update_status(jdi->backlight);
+
+	jdi->enabled = false;
+
+	return 0;
+}
+
+static int jdi_panel_unprepare(struct drm_panel *panel)
+{
+	struct jdi_panel *jdi = to_jdi_panel(panel);
+	struct device *dev = &jdi->dsi->dev;
+	int ret;
+
+	if (!jdi->prepared)
+		return 0;
+
+	jdi_panel_off(jdi);
+
+	ret = regulator_bulk_disable(ARRAY_SIZE(jdi->supplies), jdi->supplies);
+	if (ret < 0)
+		dev_err(dev, "regulator disable failed, %d\n", ret);
+
+	gpiod_set_value(jdi->enable_gpio, 0);
+
+	gpiod_set_value(jdi->reset_gpio, 0);
+
+	jdi->prepared = false;
+
+	return 0;
+}
+
+static int jdi_panel_prepare(struct drm_panel *panel)
+{
+	struct jdi_panel *jdi = to_jdi_panel(panel);
+	struct device *dev = &jdi->dsi->dev;
+	int ret;
+
+	if (jdi->prepared)
+		return 0;
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(jdi->supplies), jdi->supplies);
+	if (ret < 0) {
+		dev_err(dev, "regulator enable failed, %d\n", ret);
+		return ret;
+	}
+
+	msleep(20);
+
+	gpiod_set_value(jdi->reset_gpio, 1);
+	usleep_range(10, 20);
+
+	gpiod_set_value(jdi->enable_gpio, 1);
+	usleep_range(10, 20);
+
+	ret = jdi_panel_init(jdi);
+	if (ret < 0) {
+		dev_err(dev, "failed to init panel: %d\n", ret);
+		goto poweroff;
+	}
+
+	ret = jdi_panel_on(jdi);
+	if (ret < 0) {
+		dev_err(dev, "failed to set panel on: %d\n", ret);
+		goto poweroff;
+	}
+
+	jdi->prepared = true;
+
+	return 0;
+
+poweroff:
+	ret = regulator_bulk_disable(ARRAY_SIZE(jdi->supplies), jdi->supplies);
+	if (ret < 0)
+		dev_err(dev, "regulator disable failed, %d\n", ret);
+
+	gpiod_set_value(jdi->enable_gpio, 0);
+
+	gpiod_set_value(jdi->reset_gpio, 0);
+
+	return ret;
+}
+
+static int jdi_panel_enable(struct drm_panel *panel)
+{
+	struct jdi_panel *jdi = to_jdi_panel(panel);
+
+	if (jdi->enabled)
+		return 0;
+
+	jdi->backlight->props.power = FB_BLANK_UNBLANK;
+	backlight_update_status(jdi->backlight);
+
+	jdi->enabled = true;
+
+	return 0;
+}
+
+static const struct drm_display_mode default_mode = {
+		.clock = 155493,
+		.hdisplay = 1200,
+		.hsync_start = 1200 + 48,
+		.hsync_end = 1200 + 48 + 32,
+		.htotal = 1200 + 48 + 32 + 60,
+		.vdisplay = 1920,
+		.vsync_start = 1920 + 3,
+		.vsync_end = 1920 + 3 + 5,
+		.vtotal = 1920 + 3 + 5 + 6,
+		.vrefresh = 60,
+		.flags = 0,
+};
+
+static int jdi_panel_get_modes(struct drm_panel *panel)
+{
+	struct drm_display_mode *mode;
+	struct jdi_panel *jdi = to_jdi_panel(panel);
+	struct device *dev = &jdi->dsi->dev;
+
+	mode = drm_mode_duplicate(panel->drm, &default_mode);
+	if (!mode) {
+		dev_err(dev, "failed to add mode %ux%ux@%u\n",
+			default_mode.hdisplay, default_mode.vdisplay,
+			default_mode.vrefresh);
+		return -ENOMEM;
+	}
+
+	drm_mode_set_name(mode);
+
+	drm_mode_probed_add(panel->connector, mode);
+
+	panel->connector->display_info.width_mm = 95;
+	panel->connector->display_info.height_mm = 151;
+
+	return 1;
+}
+
+static int dsi_dcs_bl_get_brightness(struct backlight_device *bl)
+{
+	struct mipi_dsi_device *dsi = bl_get_data(bl);
+	int ret;
+	u16 brightness = bl->props.brightness;
+
+	dsi->mode_flags &= ~MIPI_DSI_MODE_LPM;
+
+	ret = mipi_dsi_dcs_get_display_brightness(dsi, &brightness);
+	if (ret < 0)
+		return ret;
+
+	dsi->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	return brightness & 0xff;
+}
+
+static int dsi_dcs_bl_update_status(struct backlight_device *bl)
+{
+	struct mipi_dsi_device *dsi = bl_get_data(bl);
+	int ret;
+
+	dsi->mode_flags &= ~MIPI_DSI_MODE_LPM;
+
+	ret = mipi_dsi_dcs_set_display_brightness(dsi, bl->props.brightness);
+	if (ret < 0)
+		return ret;
+
+	dsi->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	return 0;
+}
+
+static const struct backlight_ops dsi_bl_ops = {
+	.update_status = dsi_dcs_bl_update_status,
+	.get_brightness = dsi_dcs_bl_get_brightness,
+};
+
+struct backlight_device *
+drm_panel_create_dsi_backlight(struct mipi_dsi_device *dsi)
+{
+	struct device *dev = &dsi->dev;
+	struct backlight_properties props;
+
+	memset(&props, 0, sizeof(props));
+	props.type = BACKLIGHT_RAW;
+	props.brightness = 255;
+	props.max_brightness = 255;
+
+	return devm_backlight_device_register(dev, dev_name(dev), dev, dsi,
+					      &dsi_bl_ops, &props);
+}
+
+static const struct drm_panel_funcs jdi_panel_funcs = {
+	.disable = jdi_panel_disable,
+	.unprepare = jdi_panel_unprepare,
+	.prepare = jdi_panel_prepare,
+	.enable = jdi_panel_enable,
+	.get_modes = jdi_panel_get_modes,
+};
+
+static const struct of_device_id jdi_of_match[] = {
+	{ .compatible = "jdi,lt070me05000", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, jdi_of_match);
+
+static int jdi_panel_add(struct jdi_panel *jdi)
+{
+	struct device *dev = &jdi->dsi->dev;
+	int ret;
+	unsigned int i;
+
+	jdi->mode = &default_mode;
+
+	for (i = 0; i < ARRAY_SIZE(jdi->supplies); i++)
+		jdi->supplies[i].supply = regulator_names[i];
+
+	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(jdi->supplies),
+				      jdi->supplies);
+	if (ret < 0) {
+		dev_err(dev, "failed to init regulator, ret=%d\n", ret);
+		return ret;
+	}
+
+	jdi->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(jdi->reset_gpio)) {
+		ret = PTR_ERR(jdi->reset_gpio);
+		dev_err(dev, "cannot get reset-gpios %d\n", ret);
+		return ret;
+	}
+
+	jdi->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW);
+	if (IS_ERR(jdi->enable_gpio)) {
+		ret = PTR_ERR(jdi->enable_gpio);
+		dev_err(dev, "cannot get enable-gpio %d\n", ret);
+		return ret;
+	}
+
+	jdi->backlight = drm_panel_create_dsi_backlight(jdi->dsi);
+	if (IS_ERR(jdi->backlight)) {
+		ret = PTR_ERR(jdi->backlight);
+		dev_err(dev, "failed to register backlight %d\n", ret);
+		return ret;
+	}
+
+	drm_panel_init(&jdi->base);
+	jdi->base.funcs = &jdi_panel_funcs;
+	jdi->base.dev = &jdi->dsi->dev;
+
+	ret = drm_panel_add(&jdi->base);
+
+	return ret;
+}
+
+static void jdi_panel_del(struct jdi_panel *jdi)
+{
+	if (jdi->base.dev)
+		drm_panel_remove(&jdi->base);
+}
+
+static int jdi_panel_probe(struct mipi_dsi_device *dsi)
+{
+	struct jdi_panel *jdi;
+	int ret;
+
+	dsi->lanes = 4;
+	dsi->format = MIPI_DSI_FMT_RGB888;
+	dsi->mode_flags =  MIPI_DSI_MODE_VIDEO_HSE | MIPI_DSI_MODE_VIDEO |
+			   MIPI_DSI_CLOCK_NON_CONTINUOUS;
+
+	jdi = devm_kzalloc(&dsi->dev, sizeof(*jdi), GFP_KERNEL);
+	if (!jdi)
+		return -ENOMEM;
+
+	mipi_dsi_set_drvdata(dsi, jdi);
+
+	jdi->dsi = dsi;
+
+	ret = jdi_panel_add(jdi);
+	if (ret < 0)
+		return ret;
+
+	return mipi_dsi_attach(dsi);
+}
+
+static int jdi_panel_remove(struct mipi_dsi_device *dsi)
+{
+	struct jdi_panel *jdi = mipi_dsi_get_drvdata(dsi);
+	int ret;
+
+	ret = jdi_panel_disable(&jdi->base);
+	if (ret < 0)
+		dev_err(&dsi->dev, "failed to disable panel: %d\n", ret);
+
+	ret = mipi_dsi_detach(dsi);
+	if (ret < 0)
+		dev_err(&dsi->dev, "failed to detach from DSI host: %d\n",
+			ret);
+
+	drm_panel_detach(&jdi->base);
+	jdi_panel_del(jdi);
+
+	return 0;
+}
+
+static void jdi_panel_shutdown(struct mipi_dsi_device *dsi)
+{
+	struct jdi_panel *jdi = mipi_dsi_get_drvdata(dsi);
+
+	jdi_panel_disable(&jdi->base);
+}
+
+static struct mipi_dsi_driver jdi_panel_driver = {
+	.driver = {
+		.name = "panel-jdi-lt070me05000",
+		.of_match_table = jdi_of_match,
+	},
+	.probe = jdi_panel_probe,
+	.remove = jdi_panel_remove,
+	.shutdown = jdi_panel_shutdown,
+};
+module_mipi_dsi_driver(jdi_panel_driver);
+
+MODULE_AUTHOR("Sumit Semwal <sumit.semwal@linaro.org>");
+MODULE_AUTHOR("Vinay Simha BN <simhavcs@gmail.com>");
+MODULE_DESCRIPTION("JDI LT070ME05000 WUXGA");
+MODULE_LICENSE("GPL v2");
-- 
1.9.1

Re: [PATCH v8 4/4] drm/panel: Add JDI LT070ME05000 WUXGA DSI Panel

[John Stultz]

On Wed, Jul 13, 2016 at 9:44 AM, Vinay Simha BN <simhavcs@gmail.com> wrote:
> Add support for the JDI LT070ME05000 WUXGA DSI panel used in
> Nexus 7 2013 devices.
>
> Programming sequence for the panel is was originally found in the
> android-msm-flo-3.4-lollipop-release branch from:
>     https://android.googlesource.com/kernel/msm.git
>
> And video mode setting is from dsi-panel-jdi-dualmipi1-video.dtsi
> file in:
>     git://codeaurora.org/kernel/msm-3.10.git  LNX.LA.3.6_rb1.27
>
> Cc: Archit Taneja <archit.taneja@gmail.com>
> Cc: Rob Clark <robdclark@gmail.com>
> Cc: Sumit Semwal <sumit.semwal@linaro.org>
> Cc: John Stultz <john.stultz@linaro.org>
> Cc: Emil Velikov <emil.l.velikov@gmail.com>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: David Airlie <airlied@linux.ie>
> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
> Signed-off-by: John Stultz <john.stultz@linaro.org>
> Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>

Just fyi, I've re-integrated this patch set into my flo-WIP branch and
its working well.

I dunno if its of any use, but:
Tested-by: John Stultz <john.stultz@linaro.org>

thanks
-john

Re: [PATCH v8 4/4] drm/panel: Add JDI LT070ME05000 WUXGA DSI Panel

[Emil Velikov]

On 13 July 2016 at 19:58, John Stultz <john.stultz@linaro.org> wrote:
> On Wed, Jul 13, 2016 at 9:44 AM, Vinay Simha BN <simhavcs@gmail.com> wrote:
>> Add support for the JDI LT070ME05000 WUXGA DSI panel used in
>> Nexus 7 2013 devices.
>>
>> Programming sequence for the panel is was originally found in the
>> android-msm-flo-3.4-lollipop-release branch from:
>>     https://android.googlesource.com/kernel/msm.git
>>
>> And video mode setting is from dsi-panel-jdi-dualmipi1-video.dtsi
>> file in:
>>     git://codeaurora.org/kernel/msm-3.10.git  LNX.LA.3.6_rb1.27
>>
>> Cc: Archit Taneja <archit.taneja@gmail.com>
>> Cc: Rob Clark <robdclark@gmail.com>
>> Cc: Sumit Semwal <sumit.semwal@linaro.org>
>> Cc: John Stultz <john.stultz@linaro.org>
>> Cc: Emil Velikov <emil.l.velikov@gmail.com>
>> Cc: Thierry Reding <thierry.reding@gmail.com>
>> Cc: David Airlie <airlied@linux.ie>
>> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
>> Signed-off-by: John Stultz <john.stultz@linaro.org>
>> Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
>
> Just fyi, I've re-integrated this patch set into my flo-WIP branch and
> its working well.
>
> I dunno if its of any use, but:
> Tested-by: John Stultz <john.stultz@linaro.org>
>
It always is. Thank you!

Vinay, thanks for the patience and I hope you grok the reason behind
the requested changes.

The patch is
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>

Regards,
Emil

Re: [PATCH v2 3/4] drm/dsi: Implement dcs set/get display brightness

[Emil Velikov]

On 13 July 2016 at 17:44, Vinay Simha BN <simhavcs@gmail.com> wrote:

> +int mipi_dsi_dcs_get_display_brightness(struct mipi_dsi_device *dsi,
> +                                       u16 *brightness)
> +{
> +       ssize_t err;
> +
> +       err = mipi_dsi_dcs_read(dsi, MIPI_DCS_GET_DISPLAY_BRIGHTNESS,
> +                               brightness, sizeof(*brightness));
> +       if (err < 0) {
> +               if (err == 0)
Something looks fishy here. This can never be true, can it ?

 -Emil

Re: [PATCH v2 2/4] dt-bindings: Add jdi lt070me05000 panel bindings

[Thierry Reding]

[-- Attachment #1: Type: text/plain, Size: 2871 bytes --]

On Fri, Apr 22, 2016 at 12:25:52PM +0530, Vinay Simha wrote:
> On Thu, Apr 21, 2016 at 9:15 PM, Rob Herring <robh@kernel.org> wrote:
> > On Wed, Apr 20, 2016 at 03:02:31PM +0530, Vinay Simha BN wrote:
> >> Add documentation for lt070me05000 panel
> >>
> >> Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
> >> ---
> >>  .../bindings/display/panel/jdi,lt070me05000.txt    | 43 ++++++++++++++++++++++
> >>  1 file changed, 43 insertions(+)
> >>  create mode 100644 Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
> >>
> >> diff --git a/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
> >> new file mode 100644
> >> index 0000000..ffe0550
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
> >> @@ -0,0 +1,43 @@
> >> +JDI model LT070ME05000 1200x1920 7" DSI Panel
> >> +
> >> +Required properties:
> >> +- compatible: should be "jdi,lt070me05000"
> >> +- power-supply: phandle of the regulator that provides the supply voltage
> >> +  IOVCC , power supply for LCM (1.8V)
> >> +- vddp-supply: phandle of the regulator that provides the supply voltage
> >> +  Power IC supply (3-5V)
> >> +- dcdc_en-supply: phandle of the regulator that provides the supply voltage
> >> +  Power IC supply enable, High active
> >> +- reset-gpio: phandle of gpio for reset line
> >> +  This should be 8mA, gpio can be configured using mux and pinctrl.
> >> +  XRES, Reset, Low active
> >> +- enable-gpio: phandle of gpio for enable line
> >> +  LED_EN, LED backlight enable, High active
> >
> > These should all be -gpios instead.
> will implement in v3
> >
> >> +- vcc-gpio: phandle of regulator/gpio that provides the supply voltage
> >> +  VDD, LED power supply (3-5V)
> >
> > Is it a regulator or gpio?
> >
> VDD is LED power supply, but in nexus 7 2nd gen they are using gpio 23
> instead of regulator.
> if we use vcc-supply, not sure we can give the gpio device tree entry
> to it in nexus 7 dts. Any inputs ?

You can model it as a fixed regulator that's enabled by a GPIO. See:

	Documentation/devicetree/bindings/regulator/fixed-regulator.txt

> >> +
> >> +Optional properties:
> >> +- pwm-gpio: phandle of gpio/pwm
> >
> > This should use the PWM binding. It may not be a GPIO on some hosts.
> 
> pwm-gpio will go to the backlight (pwm). right now it is not used
> since pwm pm8921 upstream driver is not yet implemented. Shall i
> remove this pwm-gpio now and the backlight property when pwm pm8921 is
> implemented?

This suggests to me that you don't have a good idea yet what the final
binding would need to look like, so it might be better to get all the
dependencies in place first so that the binding can be validated to work
properly.

Thierry

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v2 2/4] dt-bindings: Add jdi lt070me05000 panel bindings

[Vinay Simha]

On Thu, Apr 21, 2016 at 9:15 PM, Rob Herring <robh@kernel.org> wrote:
> On Wed, Apr 20, 2016 at 03:02:31PM +0530, Vinay Simha BN wrote:
>> Add documentation for lt070me05000 panel
>>
>> Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
>> ---
>>  .../bindings/display/panel/jdi,lt070me05000.txt    | 43 ++++++++++++++++++++++
>>  1 file changed, 43 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
>>
>> diff --git a/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
>> new file mode 100644
>> index 0000000..ffe0550
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
>> @@ -0,0 +1,43 @@
>> +JDI model LT070ME05000 1200x1920 7" DSI Panel
>> +
>> +Required properties:
>> +- compatible: should be "jdi,lt070me05000"
>> +- power-supply: phandle of the regulator that provides the supply voltage
>> +  IOVCC , power supply for LCM (1.8V)
>> +- vddp-supply: phandle of the regulator that provides the supply voltage
>> +  Power IC supply (3-5V)
>> +- dcdc_en-supply: phandle of the regulator that provides the supply voltage
>> +  Power IC supply enable, High active
>> +- reset-gpio: phandle of gpio for reset line
>> +  This should be 8mA, gpio can be configured using mux and pinctrl.
>> +  XRES, Reset, Low active
>> +- enable-gpio: phandle of gpio for enable line
>> +  LED_EN, LED backlight enable, High active
>
> These should all be -gpios instead.
will implement in v3
>
>> +- vcc-gpio: phandle of regulator/gpio that provides the supply voltage
>> +  VDD, LED power supply (3-5V)
>
> Is it a regulator or gpio?
>
VDD is LED power supply, but in nexus 7 2nd gen they are using gpio 23
instead of regulator.
if we use vcc-supply, not sure we can give the gpio device tree entry
to it in nexus 7 dts. Any inputs ?
>> +
>> +Optional properties:
>> +- pwm-gpio: phandle of gpio/pwm
>
> This should use the PWM binding. It may not be a GPIO on some hosts.

pwm-gpio will go to the backlight (pwm). right now it is not used
since pwm pm8921 upstream driver is not yet implemented. Shall i
remove this pwm-gpio now and the backlight property when pwm pm8921 is
implemented?
>
>> +  pwm backlight control, this should be mapped to the backlight level
>> +  display brightness (0x51)
>> +
>> +Example:
>> +
>> +     dsi0: qcom,mdss_dsi@4700000 {
>> +             panel@0 {
>> +                     compatible = "jdi,lt070me05000";
>> +                     reg = <0>;
>> +                     pinctrl-names = "default";
>> +                     pinctrl-0 = <&dsi_panel_pinctrl>;
>> +
>> +                     power-supply = <&pm8921_lvs5>;
>> +                     vddp-supply = <&pm8921_l17>;
>> +                     dcdc_en-supply = <&pm8921_lvs7>;
>> +
>> +                     reset-gpio = <&tlmm_pinmux 54 0>;
>> +                     enable-gpio = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
>> +                     vcc-gpio = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
>> +
>> +                     pwm-gpio = <&pm8921_gpio 26 GPIO_ACTIVE_HIGH>;
>> +             };
>> +     };
>> --
>> 2.1.2
>>



-- 
Regards,

Vinay Simha.B.N.

Re: [PATCH v2 2/4] dt-bindings: Add jdi lt070me05000 panel bindings

[Rob Herring]

On Wed, Apr 20, 2016 at 03:02:31PM +0530, Vinay Simha BN wrote:
> Add documentation for lt070me05000 panel
> 
> Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
> ---
>  .../bindings/display/panel/jdi,lt070me05000.txt    | 43 ++++++++++++++++++++++
>  1 file changed, 43 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
> 
> diff --git a/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
> new file mode 100644
> index 0000000..ffe0550
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
> @@ -0,0 +1,43 @@
> +JDI model LT070ME05000 1200x1920 7" DSI Panel
> +
> +Required properties:
> +- compatible: should be "jdi,lt070me05000"
> +- power-supply: phandle of the regulator that provides the supply voltage
> +  IOVCC , power supply for LCM (1.8V)
> +- vddp-supply: phandle of the regulator that provides the supply voltage
> +  Power IC supply (3-5V)
> +- dcdc_en-supply: phandle of the regulator that provides the supply voltage
> +  Power IC supply enable, High active
> +- reset-gpio: phandle of gpio for reset line
> +  This should be 8mA, gpio can be configured using mux and pinctrl.
> +  XRES, Reset, Low active
> +- enable-gpio: phandle of gpio for enable line
> +  LED_EN, LED backlight enable, High active

These should all be -gpios instead.

> +- vcc-gpio: phandle of regulator/gpio that provides the supply voltage
> +  VDD, LED power supply (3-5V)

Is it a regulator or gpio?

> +
> +Optional properties:
> +- pwm-gpio: phandle of gpio/pwm

This should use the PWM binding. It may not be a GPIO on some hosts.

> +  pwm backlight control, this should be mapped to the backlight level
> +  display brightness (0x51)
> +
> +Example:
> +
> +	dsi0: qcom,mdss_dsi@4700000 {
> +		panel@0 {
> +			compatible = "jdi,lt070me05000";
> +			reg = <0>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&dsi_panel_pinctrl>;
> +
> +			power-supply = <&pm8921_lvs5>;
> +			vddp-supply = <&pm8921_l17>;
> +			dcdc_en-supply = <&pm8921_lvs7>;
> +
> +			reset-gpio = <&tlmm_pinmux 54 0>;
> +			enable-gpio = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
> +			vcc-gpio = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
> +
> +			pwm-gpio = <&pm8921_gpio 26 GPIO_ACTIVE_HIGH>;
> +		};
> +	};
> -- 
> 2.1.2
> 

[PATCH v2 2/4] dt-bindings: Add jdi lt070me05000 panel bindings

[Vinay Simha BN]

Add documentation for lt070me05000 panel

Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
---
 .../bindings/display/panel/jdi,lt070me05000.txt    | 43 ++++++++++++++++++++++
 1 file changed, 43 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt

diff --git a/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
new file mode 100644
index 0000000..ffe0550
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
@@ -0,0 +1,43 @@
+JDI model LT070ME05000 1200x1920 7" DSI Panel
+
+Required properties:
+- compatible: should be "jdi,lt070me05000"
+- power-supply: phandle of the regulator that provides the supply voltage
+  IOVCC , power supply for LCM (1.8V)
+- vddp-supply: phandle of the regulator that provides the supply voltage
+  Power IC supply (3-5V)
+- dcdc_en-supply: phandle of the regulator that provides the supply voltage
+  Power IC supply enable, High active
+- reset-gpio: phandle of gpio for reset line
+  This should be 8mA, gpio can be configured using mux and pinctrl.
+  XRES, Reset, Low active
+- enable-gpio: phandle of gpio for enable line
+  LED_EN, LED backlight enable, High active
+- vcc-gpio: phandle of regulator/gpio that provides the supply voltage
+  VDD, LED power supply (3-5V)
+
+Optional properties:
+- pwm-gpio: phandle of gpio/pwm
+  pwm backlight control, this should be mapped to the backlight level
+  display brightness (0x51)
+
+Example:
+
+	dsi0: qcom,mdss_dsi@4700000 {
+		panel@0 {
+			compatible = "jdi,lt070me05000";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&dsi_panel_pinctrl>;
+
+			power-supply = <&pm8921_lvs5>;
+			vddp-supply = <&pm8921_l17>;
+			dcdc_en-supply = <&pm8921_lvs7>;
+
+			reset-gpio = <&tlmm_pinmux 54 0>;
+			enable-gpio = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
+			vcc-gpio = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
+
+			pwm-gpio = <&pm8921_gpio 26 GPIO_ACTIVE_HIGH>;
+		};
+	};
-- 
2.1.2