[PATCH v3 1/6] pinctrl: bcm2835: add pull defines to dt bindings

[PATCH v3 1/6] pinctrl: bcm2835: add pull defines to dt bindings

[Gerd Hoffmann]

Also delete (unused) private enum from driver.
The pull defines can be used instead if needed.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 drivers/pinctrl/bcm/pinctrl-bcm2835.c | 6 ------
 include/dt-bindings/pinctrl/bcm2835.h | 5 +++++
 2 files changed, 5 insertions(+), 6 deletions(-)

diff --git a/drivers/pinctrl/bcm/pinctrl-bcm2835.c b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
index fa77165..4cf612b 100644
--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
@@ -76,12 +76,6 @@ enum bcm2835_pinconf_param {
 	BCM2835_PINCONF_PARAM_PULL,
 };
 
-enum bcm2835_pinconf_pull {
-	BCM2835_PINCONFIG_PULL_NONE,
-	BCM2835_PINCONFIG_PULL_DOWN,
-	BCM2835_PINCONFIG_PULL_UP,
-};
-
 #define BCM2835_PINCONF_PACK(_param_, _arg_) ((_param_) << 16 | (_arg_))
 #define BCM2835_PINCONF_UNPACK_PARAM(_conf_) ((_conf_) >> 16)
 #define BCM2835_PINCONF_UNPACK_ARG(_conf_) ((_conf_) & 0xffff)
diff --git a/include/dt-bindings/pinctrl/bcm2835.h b/include/dt-bindings/pinctrl/bcm2835.h
index 6f0bc37..e4e4fdf 100644
--- a/include/dt-bindings/pinctrl/bcm2835.h
+++ b/include/dt-bindings/pinctrl/bcm2835.h
@@ -24,4 +24,9 @@
 #define BCM2835_FSEL_ALT2	6
 #define BCM2835_FSEL_ALT3	7
 
+/* brcm,pull property */
+#define BCM2835_PUD_OFF		0
+#define BCM2835_PUD_DOWN	1
+#define BCM2835_PUD_UP		2
+
 #endif /* __DT_BINDINGS_PINCTRL_BCM2835_H__ */
-- 
1.8.3.1

[PATCH v3 2/6] ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.

[Gerd Hoffmann]

From: Eric Anholt <eric@anholt.net>

The BCM2835-ARM-Peripherals.pdf documentation specifies what the
function selects do for the pins, and there are a bunch of obvious
groupings to be made.  With these created, we'll be able to replace
bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
references to specific groups we want enabled.

Also add pinctrl groups for emmc and sdhost.

Based on patches by Eric Anholt <eric@anholt.net>

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm283x.dtsi | 203 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 203 insertions(+)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 4d9f3ab..68d559e 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -131,6 +131,209 @@
 
 			interrupt-controller;
 			#interrupt-cells = <2>;
+
+			/* Defines pin muxing groups according to
+			 * BCM2835-ARM-Peripherals.pdf page 102.
+			 *
+			 * While each pin can have its mux selected
+			 * for various functions individually, some
+			 * groups only make sense to switch to a
+			 * particular function together.
+			 */
+			dpi_gpio0: dpi_gpio0 {
+				brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
+					     12 13 14 15 16 17 18 19
+					     20 21 22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			emmc_gpio22: emmc_gpio22 {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			emmc_gpio34: emmc_gpio34 {
+				brcm,pins = <34 35 36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+				brcm,pull = <BCM2835_PUD_OFF
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP>;
+			};
+			emmc_gpio48: emmc_gpio48 {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+
+			gpclk0_gpio4: gpclk0_gpio4 {
+				brcm,pins = <4>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio5: gpclk1_gpio5 {
+				brcm,pins = <5>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio42: gpclk1_gpio42 {
+				brcm,pins = <42>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio44: gpclk1_gpio44 {
+				brcm,pins = <44>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk2_gpio6: gpclk2_gpio6 {
+				brcm,pins = <6>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk2_gpio43: gpclk2_gpio43 {
+				brcm,pins = <43>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+
+			i2c0_gpio0: i2c0_gpio0 {
+				brcm,pins = <0 1>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c0_gpio32: i2c0_gpio32 {
+				brcm,pins = <32 34>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c0_gpio44: i2c0_gpio44 {
+				brcm,pins = <44 45>;
+				brcm,function = <BCM2835_FSEL_ALT1>;
+			};
+			i2c1_gpio2: i2c1_gpio2 {
+				brcm,pins = <2 3>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c1_gpio44: i2c1_gpio44 {
+				brcm,pins = <44 45>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			i2c_slave_gpio18: i2c_slave_gpio18 {
+				brcm,pins = <18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+
+			jtag_gpio4: jtag_gpio4 {
+				brcm,pins = <4 5 6 12 13>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			jtag_gpio22: jtag_gpio22 {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+
+			pcm_gpio18: pcm_gpio18 {
+				brcm,pins = <18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pcm_gpio28: pcm_gpio28 {
+				brcm,pins = <28 29 30 31>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+
+			pwm0_gpio12: pwm0_gpio12 {
+				brcm,pins = <12>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm0_gpio18: pwm0_gpio18 {
+				brcm,pins = <18>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			pwm0_gpio40: pwm0_gpio40 {
+				brcm,pins = <40>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio13: pwm1_gpio13 {
+				brcm,pins = <13>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio19: pwm1_gpio19 {
+				brcm,pins = <19>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			pwm1_gpio41: pwm1_gpio41 {
+				brcm,pins = <41>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio45: pwm1_gpio45 {
+				brcm,pins = <45>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+
+			sdhost_gpio48: sdhost_gpio48 {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+
+			spi0_gpio7: spi0_gpio7 {
+				brcm,pins = <7 8 9 10 11>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			spi0_gpio35: spi0_gpio35 {
+				brcm,pins = <35 36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			spi1_gpio16: spi1_gpio16 {
+				brcm,pins = <16 17 18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			spi2_gpio40: spi2_gpio40 {
+				brcm,pins = <40 41 42 43 44 45>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+
+			uart0_gpio14: uart0_gpio14 {
+				brcm,pins = <14 15>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			/* Separate from the uart0_gpio14 group
+			 * because it conflicts with spi1_gpio16, and
+			 * people often run uart0 on the two pins
+			 * without flow contrl.
+			 */
+			uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 {
+				brcm,pins = <16 17>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			uart0_gpio30: uart0_gpio30 {
+				brcm,pins = <30 31>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			uart0_ctsrts_gpio32: uart0_ctsrts_gpio32 {
+				brcm,pins = <32 33>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+
+			uart1_gpio14: uart1_gpio14 {
+				brcm,pins = <14 15>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 {
+				brcm,pins = <16 17>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_gpio32: uart1_gpio32 {
+				brcm,pins = <32 33>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 {
+				brcm,pins = <30 31>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_gpio36: uart1_gpio36 {
+				brcm,pins = <36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			uart1_gpio40: uart1_gpio40 {
+				brcm,pins = <40 41>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
+				brcm,pins = <42 43>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
 		};
 
 		uart0: serial@7e201000 {
-- 
1.8.3.1

[PATCH v3 3/6] ARM: dts: bcm283x: add pinctrl group to &pwm, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index 88bcd0c..ff62236 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -38,7 +38,7 @@
 	};
 
 	alt0: alt0 {
-		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 40 45>;
+		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
 
@@ -68,6 +68,8 @@
 };
 
 &pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
 	status = "okay";
 };
 
-- 
1.8.3.1

[PATCH v3 4/6] ARM: dts: bcm283x: add pinctrl group to &i2c0, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index ff62236..b936978 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -38,7 +38,7 @@
 	};
 
 	alt0: alt0 {
-		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11>;
+		brcm,pins = <2 3 4 5 7 8 9 10 11>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
 
@@ -49,6 +49,8 @@
 };
 
 &i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_gpio0>;
 	status = "okay";
 	clock-frequency = <100000>;
 };
-- 
1.8.3.1

[PATCH v3 5/6] ARM: dts: bcm283x: add pinctrl group to &i2c1, drop pins from &gpio

[Gerd Hoffmann]

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index b936978..8688204 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -38,7 +38,7 @@
 	};
 
 	alt0: alt0 {
-		brcm,pins = <2 3 4 5 7 8 9 10 11>;
+		brcm,pins = <4 5 7 8 9 10 11>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
 
@@ -56,6 +56,8 @@
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_gpio2>;
 	status = "okay";
 	clock-frequency = <100000>;
 };
-- 
1.8.3.1

[PATCH v3 6/6] ARM: dts: bcm283x: add pinctrl group to &sdhci, drop pins from &gpio

[Gerd Hoffmann]

As the alt3 group has no pins left after this
update drop the whole alt3 group from &gpio.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index 8688204..a46fa41 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -41,11 +41,6 @@
 		brcm,pins = <4 5 7 8 9 10 11>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
-
-	alt3: alt3 {
-		brcm,pins = <48 49 50 51 52 53>;
-		brcm,function = <BCM2835_FSEL_ALT3>;
-	};
 };
 
 &i2c0 {
@@ -67,6 +62,8 @@
 };
 
 &sdhci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio48>;
 	status = "okay";
 	bus-width = <4>;
 };
-- 
1.8.3.1

Re: [PATCH v3 6/6] ARM: dts: bcm283x: add pinctrl group to &sdhci, drop pins from &gpio

[Stefan Wahren]

Hi Gerd,

> Gerd Hoffmann <kraxel@redhat.com> hat am 14. September 2016 um 10:23
> geschrieben:
> 
> 
> As the alt3 group has no pins left after this
> update drop the whole alt3 group from &gpio.

sorry it won't be that simple. The references needs to removed too :-(

> grep alt3 *.dts*
bcm2835-rpi-a.dts:	pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
bcm2835-rpi-a-plus.dts:	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
bcm2835-rpi-b.dts:	pinctrl-0 = <&gpioout &alt0 &alt3>;
bcm2835-rpi-b-plus.dts:	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
bcm2835-rpi-b-rev2.dts:	pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
bcm2835-rpi.dtsi:	alt3: alt3 {
bcm2835-rpi-zero.dts:	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
bcm2836-rpi-2-b.dts:	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;

Regards
Stefan