[RFC][PATCH 0/2 v2] dwc2 fixes for HiKey

[RFC][PATCH 0/2 v2] dwc2 fixes for HiKey

[John Stultz]

I wanted to send out two patches we're using on the dwc2
driver in order to make HiKey function.

The first is seemingly just a bug fix we ran into when
changing modes while the bus was auto-suspended.

The second is a little more interesting as it works around
a limitation of the the device in that it can't handle split
transactions, so the usb speed but be lowered and raised
manually when full-speed devices come and go.

I wanted to send these out for further review and consideration.

Changes in v2:
* Fix build issue reported by kbuildbot
* Rework to avoid using new dts entry suggested by RobH
* Further tweaks from Chen Yu to try to address comments from
  John Youn
* Further simplified logic


Feedback would be greatly appreciated!

thanks
-john


Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: Chen Yu <chenyu56@huawei.com>


Chen Yu (2):
  usb: dwc2: Force port resume on switching to device mode
  usb: dwc2: Add a quirk to allow speed negotiation for Hisilicon Hi6220

 drivers/usb/dwc2/core.h     |  6 ++++
 drivers/usb/dwc2/hcd.c      | 69 +++++++++++++++++++++++++++++++++++++++++++++
 drivers/usb/dwc2/platform.c |  1 +
 3 files changed, 76 insertions(+)

-- 
2.7.4

[RFC][PATCH 1/2 v2] usb: dwc2: Force port resume on switching to device mode

[John Stultz]

From: Chen Yu <chenyu56@huawei.com>

We've seen failures when switching between host and gadget mode,
which was diagnosed as being caused due to the bus being
auto-suspended when we switched.

So this patch forces a port resume when switching to device
mode if the bus is suspended.

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
---
 drivers/usb/dwc2/hcd.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/usb/dwc2/hcd.c b/drivers/usb/dwc2/hcd.c
index df5a065..b374e60 100644
--- a/drivers/usb/dwc2/hcd.c
+++ b/drivers/usb/dwc2/hcd.c
@@ -54,6 +54,9 @@
 #include "core.h"
 #include "hcd.h"
 
+
+static void dwc2_port_resume(struct dwc2_hsotg *hsotg);
+
 /*
  * =========================================================================
  *  Host Core Layer Functions
@@ -3204,6 +3207,11 @@ static void dwc2_conn_id_status_change(struct work_struct *work)
 	if (gotgctl & GOTGCTL_CONID_B) {
 		/* Wait for switch to device mode */
 		dev_dbg(hsotg->dev, "connId B\n");
+		if (hsotg->bus_suspended) {
+			dev_info(hsotg->dev,
+				"Do port resume before switching to device mode\n");
+			dwc2_port_resume(hsotg);
+		}
 		while (!dwc2_is_device_mode(hsotg)) {
 			dev_info(hsotg->dev,
 				 "Waiting for Peripheral Mode, Mode=%s\n",
-- 
2.7.4

[RFC][PATCH 2/2 v2] usb: dwc2: Add a quirk to allow speed negotiation for Hisilicon Hi6220

[John Stultz]

From: Chen Yu <chenyu56@huawei.com>

The Hi6220's usb controller is limited in that it does not
support "Split Transactions", so it does not support communicating
with low-speed and full-speed devices behind a high-speed hub.

Thus it requires a quirk so that we can manually drop the usb
speed when low/full-speed are attached, and bump back to high
speed when they are removed.

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Chen Yu <chenyu56@huawei.com>
[jstultz: Reworked to simplify the patch, and made
 commit log to be more specific about the issue]
Signed-off-by: John Stultz <john.stultz@linaro.org>
---
v2:
* Fix build issue reported by kbuildbot
* Rework to avoid using new dts entry suggested by RobH
* Further tweaks from Chen Yu to try to address comments from
  John Youn
* Further simplified logic
---
 drivers/usb/dwc2/core.h     |  6 +++++
 drivers/usb/dwc2/hcd.c      | 61 +++++++++++++++++++++++++++++++++++++++++++++
 drivers/usb/dwc2/platform.c |  1 +
 3 files changed, 68 insertions(+)

diff --git a/drivers/usb/dwc2/core.h b/drivers/usb/dwc2/core.h
index 2a21a04..baa4f64 100644
--- a/drivers/usb/dwc2/core.h
+++ b/drivers/usb/dwc2/core.h
@@ -417,6 +417,11 @@ enum dwc2_ep0_state {
  *			needed.
  *			0 - No (default)
  *			1 - Yes
+ * @change_speed_quirk: Change speed configuration to DWC2_SPEED_PARAM_FULL
+ *                      while full&low speed device connect. And change speed
+ *                      back to DWC2_SPEED_PARAM_HIGH while device is gone.
+ *			0 - No (default)
+ *			1 - Yes
  *
  * The following parameters may be specified when starting the module. These
  * parameters define how the DWC_otg controller should be configured. A
@@ -457,6 +462,7 @@ struct dwc2_core_params {
 	int uframe_sched;
 	int external_id_pin_ctl;
 	int hibernation;
+	int change_speed_quirk;
 };
 
 /**
diff --git a/drivers/usb/dwc2/hcd.c b/drivers/usb/dwc2/hcd.c
index b374e60..85121e2 100644
--- a/drivers/usb/dwc2/hcd.c
+++ b/drivers/usb/dwc2/hcd.c
@@ -4868,6 +4868,62 @@ static void _dwc2_hcd_clear_tt_buffer_complete(struct usb_hcd *hcd,
 	spin_unlock_irqrestore(&hsotg->lock, flags);
 }
 
+/*
+ * HPRT0_SPD_HIGH_SPEED: high speed
+ * HPRT0_SPD_FULL_SPEED: full speed
+ */
+static void dwc2_change_bus_speed(struct usb_hcd *hcd, int speed)
+{
+	struct dwc2_hsotg *hsotg = dwc2_hcd_to_hsotg(hcd);
+
+	if (hsotg->core_params->speed == speed)
+		return;
+
+	hsotg->core_params->speed = speed;
+	queue_work(hsotg->wq_otg, &hsotg->wf_otg);
+}
+
+static void dwc2_free_dev(struct usb_hcd *hcd, struct usb_device *udev)
+{
+	struct dwc2_hsotg *hsotg = dwc2_hcd_to_hsotg(hcd);
+
+	if (!hsotg->core_params->change_speed_quirk)
+		return;
+
+	/*
+	 * On removal, set speed to default high-speed.
+	 */
+	if (udev->parent &&
+			udev->parent->speed > USB_SPEED_UNKNOWN &&
+			udev->parent->speed < USB_SPEED_HIGH) {
+		dev_info(hsotg->dev, "Set speed to default high-speed\n");
+		dwc2_change_bus_speed(hcd, HPRT0_SPD_HIGH_SPEED);
+	}
+}
+
+static int dwc2_reset_device(struct usb_hcd *hcd, struct usb_device *udev)
+{
+	struct dwc2_hsotg *hsotg = dwc2_hcd_to_hsotg(hcd);
+
+	if (!hsotg->core_params->change_speed_quirk)
+		return 0;
+
+	if (udev->speed == USB_SPEED_HIGH) {
+		dev_info(hsotg->dev, "Set speed to high-speed\n");
+		dwc2_change_bus_speed(hcd, HPRT0_SPD_HIGH_SPEED);
+	} else if ((udev->speed == USB_SPEED_FULL ||
+				udev->speed == USB_SPEED_LOW)) {
+		/*
+		 * Change speed setting to full-speed if there's
+		 * a full-speed or low-speed device plugged in.
+		 */
+		dev_info(hsotg->dev, "Set speed to full-speed\n");
+		dwc2_change_bus_speed(hcd, HPRT0_SPD_FULL_SPEED);
+	}
+
+	return 0;
+}
+
 static struct hc_driver dwc2_hc_driver = {
 	.description = "dwc2_hsotg",
 	.product_desc = "DWC OTG Controller",
@@ -5023,6 +5079,11 @@ int dwc2_hcd_init(struct dwc2_hsotg *hsotg, int irq)
 			dev_warn(hsotg->dev, "can't set coherent DMA mask\n");
 	}
 
+	if (hsotg->core_params->change_speed_quirk) {
+		dwc2_hc_driver.free_dev = dwc2_free_dev;
+		dwc2_hc_driver.reset_device = dwc2_reset_device;
+	}
+
 	hcd = usb_create_hcd(&dwc2_hc_driver, hsotg->dev, dev_name(hsotg->dev));
 	if (!hcd)
 		goto error1;
diff --git a/drivers/usb/dwc2/platform.c b/drivers/usb/dwc2/platform.c
index 8e1728b..17eb5fd 100644
--- a/drivers/usb/dwc2/platform.c
+++ b/drivers/usb/dwc2/platform.c
@@ -85,6 +85,7 @@ static const struct dwc2_core_params params_hi6220 = {
 	.uframe_sched			= 0,
 	.external_id_pin_ctl		= -1,
 	.hibernation			= -1,
+	.change_speed_quirk		= 1,
 };
 
 static const struct dwc2_core_params params_bcm2835 = {
-- 
2.7.4