From: Lionel Debieve <lionel.debieve@st.com>
To: Herbert Xu <herbert@gondor.apana.org.au>,
"David S . Miller" <davem@davemloft.net>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
"Alexandre Torgue" <alexandre.torgue@st.com>,
<linux-crypto@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>,
Fabien Dessenne <fabien.dessenne@st.com>,
Ludovic Barre <ludovic.barre@st.com>
Subject: [PATCH 1/3] crypto: stm32/cryp - Add power management support
Date: Tue, 26 Jun 2018 14:52:44 +0200 [thread overview]
Message-ID: <1530017566-14779-2-git-send-email-lionel.debieve@st.com> (raw)
In-Reply-To: <1530017566-14779-1-git-send-email-lionel.debieve@st.com>
Adding pm and pm_runtime support to STM32 CRYP.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
---
drivers/crypto/stm32/stm32-cryp.c | 62 +++++++++++++++++++++++++++++++++++++++
1 file changed, 62 insertions(+)
diff --git a/drivers/crypto/stm32/stm32-cryp.c b/drivers/crypto/stm32/stm32-cryp.c
index c5d3efc..23b0b7b 100644
--- a/drivers/crypto/stm32/stm32-cryp.c
+++ b/drivers/crypto/stm32/stm32-cryp.c
@@ -11,6 +11,7 @@
#include <linux/module.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
#include <linux/reset.h>
#include <crypto/aes.h>
@@ -105,6 +106,7 @@
#define GCM_CTR_INIT 2
#define _walked_in (cryp->in_walk.offset - cryp->in_sg->offset)
#define _walked_out (cryp->out_walk.offset - cryp->out_sg->offset)
+#define CRYP_AUTOSUSPEND_DELAY 50
struct stm32_cryp_caps {
bool swap_final;
@@ -519,6 +521,8 @@ static int stm32_cryp_hw_init(struct stm32_cryp *cryp)
int ret;
u32 cfg, hw_mode;
+ pm_runtime_get_sync(cryp->dev);
+
/* Disable interrupt */
stm32_cryp_write(cryp, CRYP_IMSCR, 0);
@@ -638,6 +642,9 @@ static void stm32_cryp_finish_req(struct stm32_cryp *cryp, int err)
free_pages((unsigned long)buf_out, pages);
}
+ pm_runtime_mark_last_busy(cryp->dev);
+ pm_runtime_put_autosuspend(cryp->dev);
+
if (is_gcm(cryp) || is_ccm(cryp)) {
crypto_finalize_aead_request(cryp->engine, cryp->areq, err);
cryp->areq = NULL;
@@ -1969,6 +1976,13 @@ static int stm32_cryp_probe(struct platform_device *pdev)
return ret;
}
+ pm_runtime_set_autosuspend_delay(dev, CRYP_AUTOSUSPEND_DELAY);
+ pm_runtime_use_autosuspend(dev);
+
+ pm_runtime_get_noresume(dev);
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
+
rst = devm_reset_control_get(dev, NULL);
if (!IS_ERR(rst)) {
reset_control_assert(rst);
@@ -2008,6 +2022,8 @@ static int stm32_cryp_probe(struct platform_device *pdev)
dev_info(dev, "Initialized\n");
+ pm_runtime_put_sync(dev);
+
return 0;
err_aead_algs:
@@ -2020,6 +2036,11 @@ static int stm32_cryp_probe(struct platform_device *pdev)
list_del(&cryp->list);
spin_unlock(&cryp_list.lock);
+ pm_runtime_disable(dev);
+ pm_runtime_put_noidle(dev);
+ pm_runtime_disable(dev);
+ pm_runtime_put_noidle(dev);
+
clk_disable_unprepare(cryp->clk);
return ret;
@@ -2028,10 +2049,15 @@ static int stm32_cryp_probe(struct platform_device *pdev)
static int stm32_cryp_remove(struct platform_device *pdev)
{
struct stm32_cryp *cryp = platform_get_drvdata(pdev);
+ int ret;
if (!cryp)
return -ENODEV;
+ ret = pm_runtime_get_sync(cryp->dev);
+ if (ret < 0)
+ return ret;
+
crypto_unregister_aeads(aead_algs, ARRAY_SIZE(aead_algs));
crypto_unregister_algs(crypto_algs, ARRAY_SIZE(crypto_algs));
@@ -2041,16 +2067,52 @@ static int stm32_cryp_remove(struct platform_device *pdev)
list_del(&cryp->list);
spin_unlock(&cryp_list.lock);
+ pm_runtime_disable(cryp->dev);
+ pm_runtime_put_noidle(cryp->dev);
+
+ clk_disable_unprepare(cryp->clk);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int stm32_cryp_runtime_suspend(struct device *dev)
+{
+ struct stm32_cryp *cryp = dev_get_drvdata(dev);
+
clk_disable_unprepare(cryp->clk);
return 0;
}
+static int stm32_cryp_runtime_resume(struct device *dev)
+{
+ struct stm32_cryp *cryp = dev_get_drvdata(dev);
+ int ret;
+
+ ret = clk_prepare_enable(cryp->clk);
+ if (ret) {
+ dev_err(cryp->dev, "Failed to prepare_enable clock\n");
+ return ret;
+ }
+
+ return 0;
+}
+#endif
+
+static const struct dev_pm_ops stm32_cryp_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+ pm_runtime_force_resume)
+ SET_RUNTIME_PM_OPS(stm32_cryp_runtime_suspend,
+ stm32_cryp_runtime_resume, NULL)
+};
+
static struct platform_driver stm32_cryp_driver = {
.probe = stm32_cryp_probe,
.remove = stm32_cryp_remove,
.driver = {
.name = DRIVER_NAME,
+ .pm = &stm32_cryp_pm_ops,
.of_match_table = stm32_dt_ids,
},
};
--
2.7.4
next prev parent reply other threads:[~2018-06-26 12:55 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-06-26 12:52 [PATCH 0/3] crypto: stm32 - Add power mamagement support Lionel Debieve
2018-06-26 12:52 ` Lionel Debieve [this message]
2018-06-26 12:52 ` [PATCH 2/3] crypto: stm32/hash - Add power management support Lionel Debieve
2018-06-26 12:52 ` [PATCH 3/3] crypto: stm32/crc " Lionel Debieve
2018-07-08 16:43 ` [PATCH 0/3] crypto: stm32 - Add power mamagement support Herbert Xu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1530017566-14779-2-git-send-email-lionel.debieve@st.com \
--to=lionel.debieve@st.com \
--cc=alexandre.torgue@st.com \
--cc=benjamin.gaignard@st.com \
--cc=davem@davemloft.net \
--cc=fabien.dessenne@st.com \
--cc=herbert@gondor.apana.org.au \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-crypto@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=ludovic.barre@st.com \
--cc=mcoquelin.stm32@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®