* [PATCH v3 0/2] ARM: dts: am3355: add support for the Sancloud Beaglebone Enhanced
@ 2018-07-12 10:23 Koen Kooi
2018-07-12 10:23 ` [PATCH v3 1/2] dt-bindings: Add vendor prefix for Sancloud Koen Kooi
2018-07-12 10:23 ` [PATCH v3 2/2] ARM: dts: am335x: add am335x-sancloud-bbe board support Koen Kooi
0 siblings, 2 replies; 4+ messages in thread
From: Koen Kooi @ 2018-07-12 10:23 UTC (permalink / raw)
To: linux-omap; +Cc: Koen Kooi, linux-kernel
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
This series adds the Sancloud vendor prefix as well as the actual dts.
v3: Drop 1GHz Opp tweak
v2: * Add missing #include <dt-bindings/interrupt-controller/irq.h>
* Fix barometer compatible string
v1: Initial submission, not the dts actually tested :/
Also double checked if the kbuild error has been fixed:
koen@beast:/build/pkg/linux-torvalds$ git describe
v4.18-rc4-71-gd69088d
koen@beast:/build/pkg/linux-torvalds$ ARCH=arm CROSS_COMPILE=arm-angstrom-linux-gnueabi- make am335x-sancloud-bbe.dtb
DTC arch/arm/boot/dts/am335x-sancloud-bbe.dtb
koen@beast:/build/pkg/linux-torvalds$
Same successful result on tmlind/for-next (which has v2 already) and robh/for-next
Koen Kooi (2):
dt-bindings: Add vendor prefix for Sancloud
ARM: dts: am335x: add am335x-sancloud-bbe board support
.../devicetree/bindings/vendor-prefixes.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/am335x-sancloud-bbe.dts | 146 +++++++++++++++++++++
3 files changed, 148 insertions(+)
create mode 100644 arch/arm/boot/dts/am335x-sancloud-bbe.dts
--
2.0.1
^ permalink raw reply [flat|nested] 4+ messages in thread* [PATCH v3 1/2] dt-bindings: Add vendor prefix for Sancloud 2018-07-12 10:23 [PATCH v3 0/2] ARM: dts: am3355: add support for the Sancloud Beaglebone Enhanced Koen Kooi @ 2018-07-12 10:23 ` Koen Kooi 2018-07-12 10:23 ` [PATCH v3 2/2] ARM: dts: am335x: add am335x-sancloud-bbe board support Koen Kooi 1 sibling, 0 replies; 4+ messages in thread From: Koen Kooi @ 2018-07-12 10:23 UTC (permalink / raw) To: linux-omap Cc: Koen Kooi, Rob Herring, Mark Rutland, Andreas Färber, Noralf Trønnes, David Lechner, Shawn Guo, SZ Lin, Alexandre Belloni, devicetree, linux-kernel Add vendor prefix for Sancloud Ltd. Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> --- v3: No changes v2: No changes v1: Initial submission Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 7cad066..c7aaa1f 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -314,6 +314,7 @@ rohm ROHM Semiconductor Co., Ltd roofull Shenzhen Roofull Technology Co, Ltd samsung Samsung Semiconductor samtec Samtec/Softing company +sancloud Sancloud Ltd sandisk Sandisk Corporation sbs Smart Battery System schindler Schindler -- 2.0.1 ^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH v3 2/2] ARM: dts: am335x: add am335x-sancloud-bbe board support 2018-07-12 10:23 [PATCH v3 0/2] ARM: dts: am3355: add support for the Sancloud Beaglebone Enhanced Koen Kooi 2018-07-12 10:23 ` [PATCH v3 1/2] dt-bindings: Add vendor prefix for Sancloud Koen Kooi @ 2018-07-12 10:23 ` Koen Kooi 1 sibling, 0 replies; 4+ messages in thread From: Koen Kooi @ 2018-07-12 10:23 UTC (permalink / raw) To: linux-omap Cc: Koen Kooi, Rob Herring, Mark Rutland, Benoît Cousson, Tony Lindgren, devicetree, linux-kernel The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black, but with the following differences: * Gigabit capable PHY * Extra USB hub, optional i2c control * lps3331ap barometer connected over i2c * MPU6050 6 axis MEMS accelerometer/gyro connected over i2c * 1GiB DDR3 RAM * RTL8723 Wifi/Bluetooth connected over USB Tested on a revision G board. Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> --- v3: Drop oppnitro-1000000000, not needed on the versions Sancloud is using v2: * Add missing #include <dt-bindings/interrupt-controller/irq.h> * Fix Barometer compatible string v1: Initial submission arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/am335x-sancloud-bbe.dts | 136 ++++++++++++++++++++++++++++++ 2 files changed, 137 insertions(+) create mode 100644 arch/arm/boot/dts/am335x-sancloud-bbe.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 37a3de7..83a4d61 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -695,6 +695,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-pepper.dtb \ am335x-phycore-rdk.dtb \ am335x-pocketbeagle.dtb \ + am335x-sancloud-bbe.dtb \ am335x-shc.dtb \ am335x-sbc-t335.dtb \ am335x-sl50.dtb \ diff --git a/arch/arm/boot/dts/am335x-sancloud-bbe.dts b/arch/arm/boot/dts/am335x-sancloud-bbe.dts new file mode 100644 index 0000000..ba5f4bd --- /dev/null +++ b/arch/arm/boot/dts/am335x-sancloud-bbe.dts @@ -0,0 +1,136 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +#include "am335x-boneblack-common.dtsi" +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + model = "SanCloud BeagleBone Enhanced"; + compatible = "sancloud,am335x-boneenhanced", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ + AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ + AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ + AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ + AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ + AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */ + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */ + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + usb_hub_ctrl: usb_hub_ctrl { + pinctrl-single,pins = < + AM33XX_IOPAD(0x944, PIN_OUTPUT_PULLUP | MUX_MODE7) /* rmii1_refclk.gpio0_29 */ + >; + }; + + mpu6050_pins: pinmux_mpu6050_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x968, PIN_INPUT | MUX_MODE7) /* uart0_ctsn.gpio1_8 */ + >; + }; + + lps3331ap_pins: pinmux_lps3331ap_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x868, PIN_INPUT | MUX_MODE7) /* gpmc_a10.gpio1_26 */ + >; + }; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; +}; + +&i2c0 { + lps331ap: lps331ap@5C { + compatible = "st,lps331ap-press"; + st,drdy-int-pin = <1>; + reg = <0x5C>; + interrupt-parent = <&gpio1>; + interrupts = <26 IRQ_TYPE_EDGE_RISING>; + }; + + mpu6050: mpu6050@68 { + compatible = "invensense,mpu6050"; + reg = <0x68>; + interrupt-parent = <&gpio0>; + interrupts = <2 IRQ_TYPE_EDGE_RISING>; + orientation = <0xff 0 0 0 1 0 0 0 0xff>; + }; + + usb2512b@2c { + compatible = "microchip,usb2512b"; + reg = <0x2c>; + reset-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; + /* wifi on port 4 */ + }; +}; -- 2.0.1 ^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH v3 0/2] ARM: dts: am3355: add support for the Sancloud Beaglebone Enhanced
@ 2018-07-13 6:22 Koen Kooi
2018-07-13 6:22 ` [PATCH v3 2/2] ARM: dts: am335x: add am335x-sancloud-bbe board support Koen Kooi
0 siblings, 1 reply; 4+ messages in thread
From: Koen Kooi @ 2018-07-13 6:22 UTC (permalink / raw)
To: linux-omap; +Cc: Koen Kooi, linux-kernel
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
This series adds the Sancloud vendor prefix as well as the actual dts.
v3: Drop 1GHz Opp tweak
v2: * Add missing #include <dt-bindings/interrupt-controller/irq.h>
* Fix barometer compatible string
v1: Initial submission, not the dts actually tested :/
Also double checked if the kbuild error has been fixed:
koen@beast:/build/pkg/linux-torvalds$ git describe
v4.18-rc4-71-gd69088d
koen@beast:/build/pkg/linux-torvalds$ ARCH=arm CROSS_COMPILE=arm-angstrom-linux-gnueabi- make am335x-sancloud-bbe.dtb
DTC arch/arm/boot/dts/am335x-sancloud-bbe.dtb
koen@beast:/build/pkg/linux-torvalds$
Same successful result on tmlind/for-next (which has v2 already) and robh/for-next
Koen Kooi (2):
dt-bindings: Add vendor prefix for Sancloud
ARM: dts: am335x: add am335x-sancloud-bbe board support
.../devicetree/bindings/vendor-prefixes.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/am335x-sancloud-bbe.dts | 146 +++++++++++++++++++++
3 files changed, 148 insertions(+)
create mode 100644 arch/arm/boot/dts/am335x-sancloud-bbe.dts
--
2.0.1
^ permalink raw reply [flat|nested] 4+ messages in thread* [PATCH v3 2/2] ARM: dts: am335x: add am335x-sancloud-bbe board support 2018-07-13 6:22 [PATCH v3 0/2] ARM: dts: am3355: add support for the Sancloud Beaglebone Enhanced Koen Kooi @ 2018-07-13 6:22 ` Koen Kooi 0 siblings, 0 replies; 4+ messages in thread From: Koen Kooi @ 2018-07-13 6:22 UTC (permalink / raw) To: linux-omap Cc: Koen Kooi, Rob Herring, Mark Rutland, Benoît Cousson, Tony Lindgren, devicetree, linux-kernel The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black, but with the following differences: * Gigabit capable PHY * Extra USB hub, optional i2c control * lps3331ap barometer connected over i2c * MPU6050 6 axis MEMS accelerometer/gyro connected over i2c * 1GiB DDR3 RAM * RTL8723 Wifi/Bluetooth connected over USB Tested on a revision G board. Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> --- v3: Drop oppnitro-1000000000, not needed on the versions Sancloud is using v2: * Add missing #include <dt-bindings/interrupt-controller/irq.h> * Fix Barometer compatible string v1: Initial submission arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/am335x-sancloud-bbe.dts | 136 ++++++++++++++++++++++++++++++ 2 files changed, 137 insertions(+) create mode 100644 arch/arm/boot/dts/am335x-sancloud-bbe.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 37a3de7..83a4d61 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -695,6 +695,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-pepper.dtb \ am335x-phycore-rdk.dtb \ am335x-pocketbeagle.dtb \ + am335x-sancloud-bbe.dtb \ am335x-shc.dtb \ am335x-sbc-t335.dtb \ am335x-sl50.dtb \ diff --git a/arch/arm/boot/dts/am335x-sancloud-bbe.dts b/arch/arm/boot/dts/am335x-sancloud-bbe.dts new file mode 100644 index 0000000..ba5f4bd --- /dev/null +++ b/arch/arm/boot/dts/am335x-sancloud-bbe.dts @@ -0,0 +1,136 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +#include "am335x-boneblack-common.dtsi" +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + model = "SanCloud BeagleBone Enhanced"; + compatible = "sancloud,am335x-boneenhanced", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ + AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ + AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ + AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ + AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ + AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */ + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */ + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + usb_hub_ctrl: usb_hub_ctrl { + pinctrl-single,pins = < + AM33XX_IOPAD(0x944, PIN_OUTPUT_PULLUP | MUX_MODE7) /* rmii1_refclk.gpio0_29 */ + >; + }; + + mpu6050_pins: pinmux_mpu6050_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x968, PIN_INPUT | MUX_MODE7) /* uart0_ctsn.gpio1_8 */ + >; + }; + + lps3331ap_pins: pinmux_lps3331ap_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x868, PIN_INPUT | MUX_MODE7) /* gpmc_a10.gpio1_26 */ + >; + }; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; +}; + +&i2c0 { + lps331ap: lps331ap@5C { + compatible = "st,lps331ap-press"; + st,drdy-int-pin = <1>; + reg = <0x5C>; + interrupt-parent = <&gpio1>; + interrupts = <26 IRQ_TYPE_EDGE_RISING>; + }; + + mpu6050: mpu6050@68 { + compatible = "invensense,mpu6050"; + reg = <0x68>; + interrupt-parent = <&gpio0>; + interrupts = <2 IRQ_TYPE_EDGE_RISING>; + orientation = <0xff 0 0 0 1 0 0 0 0xff>; + }; + + usb2512b@2c { + compatible = "microchip,usb2512b"; + reg = <0x2c>; + reset-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; + /* wifi on port 4 */ + }; +}; -- 2.0.1 ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2018-07-13 6:22 UTC | newest] Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2018-07-12 10:23 [PATCH v3 0/2] ARM: dts: am3355: add support for the Sancloud Beaglebone Enhanced Koen Kooi 2018-07-12 10:23 ` [PATCH v3 1/2] dt-bindings: Add vendor prefix for Sancloud Koen Kooi 2018-07-12 10:23 ` [PATCH v3 2/2] ARM: dts: am335x: add am335x-sancloud-bbe board support Koen Kooi 2018-07-13 6:22 [PATCH v3 0/2] ARM: dts: am3355: add support for the Sancloud Beaglebone Enhanced Koen Kooi 2018-07-13 6:22 ` [PATCH v3 2/2] ARM: dts: am335x: add am335x-sancloud-bbe board support Koen Kooi
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®