* [PATCH v3 1/4] net: macb: Check MDIO state before read/write and use timeouts
2019-03-01 10:50 [PATCH v2 0/4] Macb power management support for ZynqMP Harini Katakam
@ 2019-03-01 10:50 ` Harini Katakam
2019-03-01 10:50 ` [PATCH v3 2/4] net: macb: Support clock management for tsu_clk Harini Katakam
` (3 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Harini Katakam @ 2019-03-01 10:50 UTC (permalink / raw)
To: nicolas.ferre, davem, claudiu.beznea, andrew
Cc: netdev, linux-kernel, michal.simek, harinikatakamlinux, harini.katakam
Replace the while loop in MDIO read/write functions with a timeout.
In addition, add a check for MDIO bus busy before initiating a new
operation as well to make sure there is no ongoing MDIO operation.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
v3 changes:
Used MACB_BIT for IDLE field
v2 changes:
Use readx_poll_timeout
Changes form RFC:
Cleaned up timeout implementation and moved it to a helper.
drivers/net/ethernet/cadence/macb.h | 2 ++
drivers/net/ethernet/cadence/macb_main.c | 33 ++++++++++++++++++++++++++------
2 files changed, 29 insertions(+), 6 deletions(-)
diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
index 9bbaad9..f51040f 100644
--- a/drivers/net/ethernet/cadence/macb.h
+++ b/drivers/net/ethernet/cadence/macb.h
@@ -715,6 +715,8 @@
__v; \
})
+#define MACB_READ_NSR(bp) macb_readl(bp, NSR)
+
/* struct macb_dma_desc - Hardware DMA descriptor
* @addr: DMA address of data buffer
* @ctrl: Control and status bits
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index f2915f2..a19ed2b 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -36,6 +36,7 @@
#include <linux/ip.h>
#include <linux/udp.h>
#include <linux/tcp.h>
+#include <linux/iopoll.h>
#include "macb.h"
#define MACB_RX_BUFFER_SIZE 128
@@ -79,6 +80,8 @@
*/
#define MACB_HALT_TIMEOUT 1230
+#define MACB_MDIO_TIMEOUT 1000000 /* in usecs */
+
/* DMA buffer descriptor might be different size
* depends on hardware configuration:
*
@@ -318,10 +321,23 @@ static void macb_get_hwaddr(struct macb *bp)
eth_hw_addr_random(bp->dev);
}
+static int macb_mdio_wait_for_idle(struct macb *bp)
+{
+ u32 val;
+
+ return readx_poll_timeout(MACB_READ_NSR, bp, val, val & MACB_BIT(IDLE),
+ 1, MACB_MDIO_TIMEOUT);
+}
+
static int macb_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
{
struct macb *bp = bus->priv;
int value;
+ int err;
+
+ err = macb_mdio_wait_for_idle(bp);
+ if (err < 0)
+ return err;
macb_writel(bp, MAN, (MACB_BF(SOF, MACB_MAN_SOF)
| MACB_BF(RW, MACB_MAN_READ)
@@ -329,9 +345,9 @@ static int macb_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
| MACB_BF(REGA, regnum)
| MACB_BF(CODE, MACB_MAN_CODE)));
- /* wait for end of transfer */
- while (!MACB_BFEXT(IDLE, macb_readl(bp, NSR)))
- cpu_relax();
+ err = macb_mdio_wait_for_idle(bp);
+ if (err < 0)
+ return err;
value = MACB_BFEXT(DATA, macb_readl(bp, MAN));
@@ -342,6 +358,11 @@ static int macb_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
u16 value)
{
struct macb *bp = bus->priv;
+ int err;
+
+ err = macb_mdio_wait_for_idle(bp);
+ if (err < 0)
+ return err;
macb_writel(bp, MAN, (MACB_BF(SOF, MACB_MAN_SOF)
| MACB_BF(RW, MACB_MAN_WRITE)
@@ -350,9 +371,9 @@ static int macb_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
| MACB_BF(CODE, MACB_MAN_CODE)
| MACB_BF(DATA, value)));
- /* wait for end of transfer */
- while (!MACB_BFEXT(IDLE, macb_readl(bp, NSR)))
- cpu_relax();
+ err = macb_mdio_wait_for_idle(bp);
+ if (err < 0)
+ return err;
return 0;
}
--
2.7.4
^ permalink raw reply [flat|nested] 6+ messages in thread* [PATCH v3 2/4] net: macb: Support clock management for tsu_clk
2019-03-01 10:50 [PATCH v2 0/4] Macb power management support for ZynqMP Harini Katakam
2019-03-01 10:50 ` [PATCH v3 1/4] net: macb: Check MDIO state before read/write and use timeouts Harini Katakam
@ 2019-03-01 10:50 ` Harini Katakam
2019-03-01 10:50 ` [PATCH v3 3/4] net: macb: Add pm runtime support Harini Katakam
` (2 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Harini Katakam @ 2019-03-01 10:50 UTC (permalink / raw)
To: nicolas.ferre, davem, claudiu.beznea, andrew
Cc: netdev, linux-kernel, michal.simek, harinikatakamlinux, harini.katakam
TSU clock needs to be enabled/disabled as per support in devicetree
and it should also be controlled during suspend/resume (WOL has no
dependency on this clock).
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
---
v3 and v2:
No changes
drivers/net/ethernet/cadence/macb.h | 3 ++-
drivers/net/ethernet/cadence/macb_main.c | 30 +++++++++++++++++++++++++-----
2 files changed, 27 insertions(+), 6 deletions(-)
diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
index f51040f..acc66a7 100644
--- a/drivers/net/ethernet/cadence/macb.h
+++ b/drivers/net/ethernet/cadence/macb.h
@@ -1085,7 +1085,7 @@ struct macb_config {
unsigned int dma_burst_length;
int (*clk_init)(struct platform_device *pdev, struct clk **pclk,
struct clk **hclk, struct clk **tx_clk,
- struct clk **rx_clk);
+ struct clk **rx_clk, struct clk **tsu_clk);
int (*init)(struct platform_device *pdev);
int jumbo_max_len;
};
@@ -1165,6 +1165,7 @@ struct macb {
struct clk *hclk;
struct clk *tx_clk;
struct clk *rx_clk;
+ struct clk *tsu_clk;
struct net_device *dev;
union {
struct macb_stats macb;
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index a19ed2b..be10ee4 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -3325,7 +3325,7 @@ static void macb_probe_queues(void __iomem *mem,
static int macb_clk_init(struct platform_device *pdev, struct clk **pclk,
struct clk **hclk, struct clk **tx_clk,
- struct clk **rx_clk)
+ struct clk **rx_clk, struct clk **tsu_clk)
{
struct macb_platform_data *pdata;
int err;
@@ -3359,6 +3359,10 @@ static int macb_clk_init(struct platform_device *pdev, struct clk **pclk,
if (IS_ERR(*rx_clk))
*rx_clk = NULL;
+ *tsu_clk = devm_clk_get(&pdev->dev, "tsu_clk");
+ if (IS_ERR(*tsu_clk))
+ *tsu_clk = NULL;
+
err = clk_prepare_enable(*pclk);
if (err) {
dev_err(&pdev->dev, "failed to enable pclk (%u)\n", err);
@@ -3383,8 +3387,17 @@ static int macb_clk_init(struct platform_device *pdev, struct clk **pclk,
goto err_disable_txclk;
}
+ err = clk_prepare_enable(*tsu_clk);
+ if (err) {
+ dev_err(&pdev->dev, "failed to enable tsu_clk (%u)\n", err);
+ goto err_disable_rxclk;
+ }
+
return 0;
+err_disable_rxclk:
+ clk_disable_unprepare(*rx_clk);
+
err_disable_txclk:
clk_disable_unprepare(*tx_clk);
@@ -3835,13 +3848,14 @@ static const struct net_device_ops at91ether_netdev_ops = {
static int at91ether_clk_init(struct platform_device *pdev, struct clk **pclk,
struct clk **hclk, struct clk **tx_clk,
- struct clk **rx_clk)
+ struct clk **rx_clk, struct clk **tsu_clk)
{
int err;
*hclk = NULL;
*tx_clk = NULL;
*rx_clk = NULL;
+ *tsu_clk = NULL;
*pclk = devm_clk_get(&pdev->dev, "ether_clk");
if (IS_ERR(*pclk))
@@ -3992,11 +4006,12 @@ static int macb_probe(struct platform_device *pdev)
{
const struct macb_config *macb_config = &default_gem_config;
int (*clk_init)(struct platform_device *, struct clk **,
- struct clk **, struct clk **, struct clk **)
- = macb_config->clk_init;
+ struct clk **, struct clk **, struct clk **,
+ struct clk **) = macb_config->clk_init;
int (*init)(struct platform_device *) = macb_config->init;
struct device_node *np = pdev->dev.of_node;
struct clk *pclk, *hclk = NULL, *tx_clk = NULL, *rx_clk = NULL;
+ struct clk *tsu_clk = NULL;
unsigned int queue_mask, num_queues;
struct macb_platform_data *pdata;
bool native_io;
@@ -4024,7 +4039,7 @@ static int macb_probe(struct platform_device *pdev)
}
}
- err = clk_init(pdev, &pclk, &hclk, &tx_clk, &rx_clk);
+ err = clk_init(pdev, &pclk, &hclk, &tx_clk, &rx_clk, &tsu_clk);
if (err)
return err;
@@ -4061,6 +4076,7 @@ static int macb_probe(struct platform_device *pdev)
bp->hclk = hclk;
bp->tx_clk = tx_clk;
bp->rx_clk = rx_clk;
+ bp->tsu_clk = tsu_clk;
if (macb_config)
bp->jumbo_max_len = macb_config->jumbo_max_len;
@@ -4180,6 +4196,7 @@ static int macb_probe(struct platform_device *pdev)
clk_disable_unprepare(hclk);
clk_disable_unprepare(pclk);
clk_disable_unprepare(rx_clk);
+ clk_disable_unprepare(tsu_clk);
return err;
}
@@ -4207,6 +4224,7 @@ static int macb_remove(struct platform_device *pdev)
clk_disable_unprepare(bp->hclk);
clk_disable_unprepare(bp->pclk);
clk_disable_unprepare(bp->rx_clk);
+ clk_disable_unprepare(bp->tsu_clk);
of_node_put(bp->phy_node);
free_netdev(dev);
}
@@ -4232,6 +4250,7 @@ static int __maybe_unused macb_suspend(struct device *dev)
clk_disable_unprepare(bp->pclk);
clk_disable_unprepare(bp->rx_clk);
}
+ clk_disable_unprepare(bp->tsu_clk);
return 0;
}
@@ -4251,6 +4270,7 @@ static int __maybe_unused macb_resume(struct device *dev)
clk_prepare_enable(bp->tx_clk);
clk_prepare_enable(bp->rx_clk);
}
+ clk_prepare_enable(bp->tsu_clk);
netif_device_attach(netdev);
--
2.7.4
^ permalink raw reply [flat|nested] 6+ messages in thread* [PATCH v3 3/4] net: macb: Add pm runtime support
2019-03-01 10:50 [PATCH v2 0/4] Macb power management support for ZynqMP Harini Katakam
2019-03-01 10:50 ` [PATCH v3 1/4] net: macb: Check MDIO state before read/write and use timeouts Harini Katakam
2019-03-01 10:50 ` [PATCH v3 2/4] net: macb: Support clock management for tsu_clk Harini Katakam
@ 2019-03-01 10:50 ` Harini Katakam
2019-03-01 10:50 ` [PATCH v3 4/4] net: macb: Add support for suspend/resume with full power down Harini Katakam
2019-03-03 21:51 ` [PATCH v2 0/4] Macb power management support for ZynqMP David Miller
4 siblings, 0 replies; 6+ messages in thread
From: Harini Katakam @ 2019-03-01 10:50 UTC (permalink / raw)
To: nicolas.ferre, davem, claudiu.beznea, andrew
Cc: netdev, linux-kernel, michal.simek, harinikatakamlinux, harini.katakam
Add runtime pm functions and move clock handling there.
Add runtime PM calls to mdio functions to allow for active mdio bus.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
---
v3 changes:
Fix exit path using goto
v2 changes:
Allow for mdio bus to be active
Changes from RFC:
Updated pm get sync/put sync calls.
Removed unecessary clk up in mdio helpers.
drivers/net/ethernet/cadence/macb_main.c | 148 +++++++++++++++++++++++--------
1 file changed, 112 insertions(+), 36 deletions(-)
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index be10ee4..5173c02 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -37,6 +37,7 @@
#include <linux/udp.h>
#include <linux/tcp.h>
#include <linux/iopoll.h>
+#include <linux/pm_runtime.h>
#include "macb.h"
#define MACB_RX_BUFFER_SIZE 128
@@ -80,6 +81,8 @@
*/
#define MACB_HALT_TIMEOUT 1230
+#define MACB_PM_TIMEOUT 100 /* ms */
+
#define MACB_MDIO_TIMEOUT 1000000 /* in usecs */
/* DMA buffer descriptor might be different size
@@ -332,12 +335,15 @@ static int macb_mdio_wait_for_idle(struct macb *bp)
static int macb_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
{
struct macb *bp = bus->priv;
- int value;
- int err;
+ int status;
- err = macb_mdio_wait_for_idle(bp);
- if (err < 0)
- return err;
+ status = pm_runtime_get_sync(&bp->pdev->dev);
+ if (status < 0)
+ goto mdio_pm_exit;
+
+ status = macb_mdio_wait_for_idle(bp);
+ if (status < 0)
+ goto mdio_read_exit;
macb_writel(bp, MAN, (MACB_BF(SOF, MACB_MAN_SOF)
| MACB_BF(RW, MACB_MAN_READ)
@@ -345,24 +351,32 @@ static int macb_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
| MACB_BF(REGA, regnum)
| MACB_BF(CODE, MACB_MAN_CODE)));
- err = macb_mdio_wait_for_idle(bp);
- if (err < 0)
- return err;
+ status = macb_mdio_wait_for_idle(bp);
+ if (status < 0)
+ goto mdio_read_exit;
- value = MACB_BFEXT(DATA, macb_readl(bp, MAN));
+ status = MACB_BFEXT(DATA, macb_readl(bp, MAN));
- return value;
+mdio_read_exit:
+ pm_runtime_mark_last_busy(&bp->pdev->dev);
+ pm_runtime_put_autosuspend(&bp->pdev->dev);
+mdio_pm_exit:
+ return status;
}
static int macb_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
u16 value)
{
struct macb *bp = bus->priv;
- int err;
+ int status;
- err = macb_mdio_wait_for_idle(bp);
- if (err < 0)
- return err;
+ status = pm_runtime_get_sync(&bp->pdev->dev);
+ if (status < 0)
+ goto mdio_pm_exit;
+
+ status = macb_mdio_wait_for_idle(bp);
+ if (status < 0)
+ goto mdio_write_exit;
macb_writel(bp, MAN, (MACB_BF(SOF, MACB_MAN_SOF)
| MACB_BF(RW, MACB_MAN_WRITE)
@@ -371,11 +385,15 @@ static int macb_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
| MACB_BF(CODE, MACB_MAN_CODE)
| MACB_BF(DATA, value)));
- err = macb_mdio_wait_for_idle(bp);
- if (err < 0)
- return err;
+ status = macb_mdio_wait_for_idle(bp);
+ if (status < 0)
+ goto mdio_write_exit;
- return 0;
+mdio_write_exit:
+ pm_runtime_mark_last_busy(&bp->pdev->dev);
+ pm_runtime_put_autosuspend(&bp->pdev->dev);
+mdio_pm_exit:
+ return status;
}
/**
@@ -2418,12 +2436,18 @@ static int macb_open(struct net_device *dev)
netdev_dbg(bp->dev, "open\n");
+ err = pm_runtime_get_sync(&bp->pdev->dev);
+ if (err < 0)
+ goto pm_exit;
+
/* carrier starts down */
netif_carrier_off(dev);
/* if the phy is not yet register, retry later*/
- if (!dev->phydev)
- return -EAGAIN;
+ if (!dev->phydev) {
+ err = -EAGAIN;
+ goto pm_exit;
+ }
/* RX buffers initialization */
macb_init_rx_buffer_size(bp, bufsz);
@@ -2432,7 +2456,7 @@ static int macb_open(struct net_device *dev)
if (err) {
netdev_err(dev, "Unable to allocate DMA memory (error %d)\n",
err);
- return err;
+ goto pm_exit;
}
bp->macbgem_ops.mog_init_rings(bp);
@@ -2449,6 +2473,11 @@ static int macb_open(struct net_device *dev)
if (bp->ptp_info)
bp->ptp_info->ptp_init(dev);
+pm_exit:
+ if (err) {
+ pm_runtime_put_sync(&bp->pdev->dev);
+ return err;
+ }
return 0;
}
@@ -2477,6 +2506,8 @@ static int macb_close(struct net_device *dev)
if (bp->ptp_info)
bp->ptp_info->ptp_remove(dev);
+ pm_runtime_put(&bp->pdev->dev);
+
return 0;
}
@@ -4043,6 +4074,11 @@ static int macb_probe(struct platform_device *pdev)
if (err)
return err;
+ pm_runtime_set_autosuspend_delay(&pdev->dev, MACB_PM_TIMEOUT);
+ pm_runtime_use_autosuspend(&pdev->dev);
+ pm_runtime_get_noresume(&pdev->dev);
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
native_io = hw_is_native_io(mem);
macb_probe_queues(mem, native_io, &queue_mask, &num_queues);
@@ -4178,6 +4214,9 @@ static int macb_probe(struct platform_device *pdev)
macb_is_gem(bp) ? "GEM" : "MACB", macb_readl(bp, MID),
dev->base_addr, dev->irq, dev->dev_addr);
+ pm_runtime_mark_last_busy(&bp->pdev->dev);
+ pm_runtime_put_autosuspend(&bp->pdev->dev);
+
return 0;
err_out_unregister_mdio:
@@ -4197,6 +4236,9 @@ static int macb_probe(struct platform_device *pdev)
clk_disable_unprepare(pclk);
clk_disable_unprepare(rx_clk);
clk_disable_unprepare(tsu_clk);
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_set_suspended(&pdev->dev);
+ pm_runtime_dont_use_autosuspend(&pdev->dev);
return err;
}
@@ -4220,11 +4262,16 @@ static int macb_remove(struct platform_device *pdev)
mdiobus_free(bp->mii_bus);
unregister_netdev(dev);
- clk_disable_unprepare(bp->tx_clk);
- clk_disable_unprepare(bp->hclk);
- clk_disable_unprepare(bp->pclk);
- clk_disable_unprepare(bp->rx_clk);
- clk_disable_unprepare(bp->tsu_clk);
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_dont_use_autosuspend(&pdev->dev);
+ if (!pm_runtime_suspended(&pdev->dev)) {
+ clk_disable_unprepare(bp->tx_clk);
+ clk_disable_unprepare(bp->hclk);
+ clk_disable_unprepare(bp->pclk);
+ clk_disable_unprepare(bp->rx_clk);
+ clk_disable_unprepare(bp->tsu_clk);
+ pm_runtime_set_suspended(&pdev->dev);
+ }
of_node_put(bp->phy_node);
free_netdev(dev);
}
@@ -4244,13 +4291,9 @@ static int __maybe_unused macb_suspend(struct device *dev)
macb_writel(bp, IER, MACB_BIT(WOL));
macb_writel(bp, WOL, MACB_BIT(MAG));
enable_irq_wake(bp->queues[0].irq);
- } else {
- clk_disable_unprepare(bp->tx_clk);
- clk_disable_unprepare(bp->hclk);
- clk_disable_unprepare(bp->pclk);
- clk_disable_unprepare(bp->rx_clk);
}
- clk_disable_unprepare(bp->tsu_clk);
+
+ pm_runtime_force_suspend(dev);
return 0;
}
@@ -4260,11 +4303,43 @@ static int __maybe_unused macb_resume(struct device *dev)
struct net_device *netdev = dev_get_drvdata(dev);
struct macb *bp = netdev_priv(netdev);
+ pm_runtime_force_resume(dev);
+
if (bp->wol & MACB_WOL_ENABLED) {
macb_writel(bp, IDR, MACB_BIT(WOL));
macb_writel(bp, WOL, 0);
disable_irq_wake(bp->queues[0].irq);
- } else {
+ }
+
+ netif_device_attach(netdev);
+
+ return 0;
+}
+
+static int __maybe_unused macb_runtime_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct net_device *netdev = platform_get_drvdata(pdev);
+ struct macb *bp = netdev_priv(netdev);
+
+ if (!(device_may_wakeup(&bp->dev->dev))) {
+ clk_disable_unprepare(bp->tx_clk);
+ clk_disable_unprepare(bp->hclk);
+ clk_disable_unprepare(bp->pclk);
+ clk_disable_unprepare(bp->rx_clk);
+ }
+ clk_disable_unprepare(bp->tsu_clk);
+
+ return 0;
+}
+
+static int __maybe_unused macb_runtime_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct net_device *netdev = platform_get_drvdata(pdev);
+ struct macb *bp = netdev_priv(netdev);
+
+ if (!(device_may_wakeup(&bp->dev->dev))) {
clk_prepare_enable(bp->pclk);
clk_prepare_enable(bp->hclk);
clk_prepare_enable(bp->tx_clk);
@@ -4272,12 +4347,13 @@ static int __maybe_unused macb_resume(struct device *dev)
}
clk_prepare_enable(bp->tsu_clk);
- netif_device_attach(netdev);
-
return 0;
}
-static SIMPLE_DEV_PM_OPS(macb_pm_ops, macb_suspend, macb_resume);
+static const struct dev_pm_ops macb_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(macb_suspend, macb_resume)
+ SET_RUNTIME_PM_OPS(macb_runtime_suspend, macb_runtime_resume, NULL)
+};
static struct platform_driver macb_driver = {
.probe = macb_probe,
--
2.7.4
^ permalink raw reply [flat|nested] 6+ messages in thread* [PATCH v3 4/4] net: macb: Add support for suspend/resume with full power down
2019-03-01 10:50 [PATCH v2 0/4] Macb power management support for ZynqMP Harini Katakam
` (2 preceding siblings ...)
2019-03-01 10:50 ` [PATCH v3 3/4] net: macb: Add pm runtime support Harini Katakam
@ 2019-03-01 10:50 ` Harini Katakam
2019-03-03 21:51 ` [PATCH v2 0/4] Macb power management support for ZynqMP David Miller
4 siblings, 0 replies; 6+ messages in thread
From: Harini Katakam @ 2019-03-01 10:50 UTC (permalink / raw)
To: nicolas.ferre, davem, claudiu.beznea, andrew
Cc: netdev, linux-kernel, michal.simek, harinikatakamlinux, harini.katakam
When macb device is suspended and system is powered down, the clocks
are removed and hence macb should be closed gracefully and restored
upon resume. This patch does the same by switching off the net device,
suspending phy and performing necessary cleanup of interrupts and BDs.
Upon resume, all these are reinitialized again.
Reset of macb device is done only when GEM is not a wake device.
Even when gem is a wake device, tx queues can be stopped and ptp device
can be closed (tsu clock will be disabled in pm_runtime_suspend) as
wake event detection has no dependency on this.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
---
v3:
Fix >80 char lines
v2 changes:
Fixed parameter passed to phy calls.
drivers/net/ethernet/cadence/macb_main.c | 40 ++++++++++++++++++++++++++++++--
1 file changed, 38 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index 5173c02..ad099fd 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -4283,16 +4283,34 @@ static int __maybe_unused macb_suspend(struct device *dev)
{
struct net_device *netdev = dev_get_drvdata(dev);
struct macb *bp = netdev_priv(netdev);
+ struct macb_queue *queue = bp->queues;
+ unsigned long flags;
+ unsigned int q;
+
+ if (!netif_running(netdev))
+ return 0;
- netif_carrier_off(netdev);
- netif_device_detach(netdev);
if (bp->wol & MACB_WOL_ENABLED) {
macb_writel(bp, IER, MACB_BIT(WOL));
macb_writel(bp, WOL, MACB_BIT(MAG));
enable_irq_wake(bp->queues[0].irq);
+ netif_device_detach(netdev);
+ } else {
+ netif_device_detach(netdev);
+ for (q = 0, queue = bp->queues; q < bp->num_queues;
+ ++q, ++queue)
+ napi_disable(&queue->napi);
+ phy_stop(netdev->phydev);
+ phy_suspend(netdev->phydev);
+ spin_lock_irqsave(&bp->lock, flags);
+ macb_reset_hw(bp);
+ spin_unlock_irqrestore(&bp->lock, flags);
}
+ netif_carrier_off(netdev);
+ if (bp->ptp_info)
+ bp->ptp_info->ptp_remove(netdev);
pm_runtime_force_suspend(dev);
return 0;
@@ -4302,6 +4320,11 @@ static int __maybe_unused macb_resume(struct device *dev)
{
struct net_device *netdev = dev_get_drvdata(dev);
struct macb *bp = netdev_priv(netdev);
+ struct macb_queue *queue = bp->queues;
+ unsigned int q;
+
+ if (!netif_running(netdev))
+ return 0;
pm_runtime_force_resume(dev);
@@ -4309,9 +4332,22 @@ static int __maybe_unused macb_resume(struct device *dev)
macb_writel(bp, IDR, MACB_BIT(WOL));
macb_writel(bp, WOL, 0);
disable_irq_wake(bp->queues[0].irq);
+ } else {
+ macb_writel(bp, NCR, MACB_BIT(MPE));
+ for (q = 0, queue = bp->queues; q < bp->num_queues;
+ ++q, ++queue)
+ napi_enable(&queue->napi);
+ phy_resume(netdev->phydev);
+ phy_init_hw(netdev->phydev);
+ phy_start(netdev->phydev);
}
+ bp->macbgem_ops.mog_init_rings(bp);
+ macb_init_hw(bp);
+ macb_set_rx_mode(netdev);
netif_device_attach(netdev);
+ if (bp->ptp_info)
+ bp->ptp_info->ptp_init(netdev);
return 0;
}
--
2.7.4
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: [PATCH v2 0/4] Macb power management support for ZynqMP
2019-03-01 10:50 [PATCH v2 0/4] Macb power management support for ZynqMP Harini Katakam
` (3 preceding siblings ...)
2019-03-01 10:50 ` [PATCH v3 4/4] net: macb: Add support for suspend/resume with full power down Harini Katakam
@ 2019-03-03 21:51 ` David Miller
4 siblings, 0 replies; 6+ messages in thread
From: David Miller @ 2019-03-03 21:51 UTC (permalink / raw)
To: harini.katakam
Cc: nicolas.ferre, claudiu.beznea, andrew, netdev, linux-kernel,
michal.simek, harinikatakamlinux
From: Harini Katakam <harini.katakam@xilinx.com>
Date: Fri, 1 Mar 2019 16:20:31 +0530
> This series adds support for macb suspend/resume with system power down.
> In relation to the above, this series also updates mdio_read/write
> function for PM and adds tsu clock management.
Series applied to net-next, thank you.
^ permalink raw reply [flat|nested] 6+ messages in thread