[PATCH 4/5] scsi: hisi_sas: Modify v3 HW SATA completion error processing

[John Garry <john.garry@huawei.com>]

From: Xingui Yang <yangxingui@huawei.com>

If the I/O completion response frame returned by the target device has been
written to the host memory and the err bit in the status field of the
received fis is 1, ts->stat should set to SAS_PROTO_RESPONSE, and this will
let EH analyze and further determine cause of failure.

Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
---
 drivers/scsi/hisi_sas/hisi_sas_v3_hw.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c b/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
index 4d3eb53a8209..efe8c5be5870 100644
--- a/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
+++ b/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
@@ -481,6 +481,9 @@ struct hisi_sas_err_record_v3 {
 #define RX_DATA_LEN_UNDERFLOW_OFF	6
 #define RX_DATA_LEN_UNDERFLOW_MSK	(1 << RX_DATA_LEN_UNDERFLOW_OFF)
 
+#define RX_FIS_STATUS_ERR_OFF		0
+#define RX_FIS_STATUS_ERR_MSK		(1 << RX_FIS_STATUS_ERR_OFF)
+
 #define HISI_SAS_COMMAND_ENTRIES_V3_HW 4096
 #define HISI_SAS_MSI_COUNT_V3_HW 32
 
@@ -2161,6 +2164,7 @@ slot_err_v3_hw(struct hisi_hba *hisi_hba, struct sas_task *task,
 			hisi_sas_status_buf_addr_mem(slot);
 	u32 dma_rx_err_type = le32_to_cpu(record->dma_rx_err_type);
 	u32 trans_tx_fail_type = le32_to_cpu(record->trans_tx_fail_type);
+	u16 sipc_rx_err_type = le16_to_cpu(record->sipc_rx_err_type);
 	u32 dw3 = le32_to_cpu(complete_hdr->dw3);
 
 	switch (task->task_proto) {
@@ -2188,7 +2192,10 @@ slot_err_v3_hw(struct hisi_hba *hisi_hba, struct sas_task *task,
 	case SAS_PROTOCOL_SATA:
 	case SAS_PROTOCOL_STP:
 	case SAS_PROTOCOL_SATA | SAS_PROTOCOL_STP:
-		if (dma_rx_err_type & RX_DATA_LEN_UNDERFLOW_MSK) {
+		if ((complete_hdr->dw0 & CMPLT_HDR_RSPNS_XFRD_MSK) &&
+		    (sipc_rx_err_type & RX_FIS_STATUS_ERR_MSK)) {
+			ts->stat = SAS_PROTO_RESPONSE;
+		} else if (dma_rx_err_type & RX_DATA_LEN_UNDERFLOW_MSK) {
 			ts->residual = trans_tx_fail_type;
 			ts->stat = SAS_DATA_UNDERRUN;
 		} else if (dw3 & CMPLT_HDR_IO_IN_TARGET_MSK) {
-- 
2.35.3