* [PATCH 1/3] ARM: dts: qcom: pm8226: Add thermal sensor and thermal zone config
2023-05-29 22:14 [PATCH 0/3] Thermal zones for pm8226, pm8841 and pm8941 Matti Lehtimäki
@ 2023-05-29 22:14 ` Matti Lehtimäki
2023-05-29 22:15 ` [PATCH 2/3] ARM: dts: qcom: pm8841: Add " Matti Lehtimäki
` (2 subsequent siblings)
3 siblings, 0 replies; 5+ messages in thread
From: Matti Lehtimäki @ 2023-05-29 22:14 UTC (permalink / raw)
To: linux-arm-msm
Cc: ~postmarketos/upstreaming, phone-devel, Matti Lehtimäki,
Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, devicetree, linux-kernel
Add thermal sensor, which is using on chip VADC channel to report PMIC
die temperature. Also add the corresponding thermal zone.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
---
arch/arm/boot/dts/qcom-pm8226.dtsi | 39 ++++++++++++++++++++++++++++++
1 file changed, 39 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-pm8226.dtsi b/arch/arm/boot/dts/qcom-pm8226.dtsi
index 46ba84f86c9f..3b8ad28cecb0 100644
--- a/arch/arm/boot/dts/qcom-pm8226.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8226.dtsi
@@ -4,6 +4,36 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
+/ {
+ thermal-zones {
+ pm8226-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+ thermal-sensors = <&pm8226_temp>;
+
+ trips {
+ trip0 {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ crit {
+ temperature = <145000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
+
&spmi_bus {
pm8226_0: pm8226@0 {
compatible = "qcom,pm8226", "qcom,spmi-pmic";
@@ -55,6 +85,15 @@ smbb: charger@1000 {
chg_otg: otg-vbus { };
};
+ pm8226_temp: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+ io-channels = <&pm8226_vadc VADC_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
pm8226_vadc: adc@3100 {
compatible = "qcom,spmi-vadc";
reg = <0x3100>;
--
2.34.1
^ permalink raw reply [flat|nested] 5+ messages in thread* [PATCH 2/3] ARM: dts: qcom: pm8841: Add thermal zone config
2023-05-29 22:14 [PATCH 0/3] Thermal zones for pm8226, pm8841 and pm8941 Matti Lehtimäki
2023-05-29 22:14 ` [PATCH 1/3] ARM: dts: qcom: pm8226: Add thermal sensor and thermal zone config Matti Lehtimäki
@ 2023-05-29 22:15 ` Matti Lehtimäki
2023-05-29 22:15 ` [PATCH 3/3] ARM: dts: qcom: pm8941: " Matti Lehtimäki
2023-06-13 23:48 ` [PATCH 0/3] Thermal zones for pm8226, pm8841 and pm8941 Bjorn Andersson
3 siblings, 0 replies; 5+ messages in thread
From: Matti Lehtimäki @ 2023-05-29 22:15 UTC (permalink / raw)
To: linux-arm-msm
Cc: ~postmarketos/upstreaming, phone-devel, Matti Lehtimäki,
Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, devicetree, linux-kernel
Add thermal zone for the PMIC thermal sensor. Temperatures are based on
downstream values, except for critical trip point where 140°C is used
instead of 145°C due to limitations without a configured ADC.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
---
arch/arm/boot/dts/qcom-pm8841.dtsi | 33 +++++++++++++++++++++++++++++-
1 file changed, 32 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/qcom-pm8841.dtsi b/arch/arm/boot/dts/qcom-pm8841.dtsi
index b5cdde034d18..3bf2ce5c86a6 100644
--- a/arch/arm/boot/dts/qcom-pm8841.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8841.dtsi
@@ -2,6 +2,37 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
+
+/ {
+ thermal-zones {
+ pm8841-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+ thermal-sensors = <&pm8841_temp>;
+
+ trips {
+ trip0 {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ crit {
+ temperature = <140000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
+
&spmi_bus {
pm8841_0: pm8841@4 {
@@ -20,7 +51,7 @@ pm8841_mpps: mpps@a000 {
#interrupt-cells = <2>;
};
- temp-alarm@2400 {
+ pm8841_temp: temp-alarm@2400 {
compatible = "qcom,spmi-temp-alarm";
reg = <0x2400>;
interrupts = <4 0x24 0 IRQ_TYPE_EDGE_RISING>;
--
2.34.1
^ permalink raw reply [flat|nested] 5+ messages in thread* [PATCH 3/3] ARM: dts: qcom: pm8941: Add thermal zone config
2023-05-29 22:14 [PATCH 0/3] Thermal zones for pm8226, pm8841 and pm8941 Matti Lehtimäki
2023-05-29 22:14 ` [PATCH 1/3] ARM: dts: qcom: pm8226: Add thermal sensor and thermal zone config Matti Lehtimäki
2023-05-29 22:15 ` [PATCH 2/3] ARM: dts: qcom: pm8841: Add " Matti Lehtimäki
@ 2023-05-29 22:15 ` Matti Lehtimäki
2023-06-13 23:48 ` [PATCH 0/3] Thermal zones for pm8226, pm8841 and pm8941 Bjorn Andersson
3 siblings, 0 replies; 5+ messages in thread
From: Matti Lehtimäki @ 2023-05-29 22:15 UTC (permalink / raw)
To: linux-arm-msm
Cc: ~postmarketos/upstreaming, phone-devel, Matti Lehtimäki,
Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, devicetree, linux-kernel
Add thermal zone for the PMIC thermal sensor.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
---
arch/arm/boot/dts/qcom-pm8941.dtsi | 31 ++++++++++++++++++++++++++++++
1 file changed, 31 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi
index a821f0368a28..b3e246bacd78 100644
--- a/arch/arm/boot/dts/qcom-pm8941.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8941.dtsi
@@ -3,6 +3,37 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
+
+/ {
+ thermal-zones {
+ pm8941-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+ thermal-sensors = <&pm8941_temp>;
+
+ trips {
+ trip0 {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+
+ crit {
+ temperature = <145000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
+
&spmi_bus {
pm8941_0: pm8941@0 {
--
2.34.1
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: [PATCH 0/3] Thermal zones for pm8226, pm8841 and pm8941
2023-05-29 22:14 [PATCH 0/3] Thermal zones for pm8226, pm8841 and pm8941 Matti Lehtimäki
` (2 preceding siblings ...)
2023-05-29 22:15 ` [PATCH 3/3] ARM: dts: qcom: pm8941: " Matti Lehtimäki
@ 2023-06-13 23:48 ` Bjorn Andersson
3 siblings, 0 replies; 5+ messages in thread
From: Bjorn Andersson @ 2023-06-13 23:48 UTC (permalink / raw)
To: linux-arm-msm, Matti Lehtimäki
Cc: devicetree, linux-kernel, phone-devel, ~postmarketos/upstreaming,
Konrad Dybcio
On Tue, 30 May 2023 01:14:58 +0300, Matti Lehtimäki wrote:
> Add thermal sensor for pm8226, which is using on chip VADC channel to
> report PMIC die temperature. Add thermal zone configurations for
> PMIC thermal sensors found in pm8226, pm8841 and pm8941.
>
> Matti Lehtimäki (3):
> ARM: dts: qcom: pm8226: Add thermal sensor and thermal zone config
> ARM: dts: qcom: pm8841: Add thermal zone config
> ARM: dts: qcom: pm8941: Add thermal zone config
>
> [...]
Applied, thanks!
[1/3] ARM: dts: qcom: pm8226: Add thermal sensor and thermal zone config
commit: 1b118df488f2be09b846994a4135d57f634e564b
[2/3] ARM: dts: qcom: pm8841: Add thermal zone config
commit: 84e72ea467db83043858b48fcd97de4c9e68881a
[3/3] ARM: dts: qcom: pm8941: Add thermal zone config
commit: 637cc974046abe5718bf045a1bc66a238778a145
Best regards,
--
Bjorn Andersson <andersson@kernel.org>
^ permalink raw reply [flat|nested] 5+ messages in thread