* [PATCH v5 1/3] dt-bindings: vendor-prefixes: Add prefix for Ariaboard
2024-11-08 3:18 [PATCH v5 0/3] Add support for Ariaboard Photonicat RK3568 Junhao Xie
@ 2024-11-08 3:18 ` Junhao Xie
2024-11-08 3:18 ` [PATCH v5 2/3] dt-bindings: arm: rockchip: Add Ariaboard Photonicat RK3568 Junhao Xie
` (2 subsequent siblings)
3 siblings, 0 replies; 5+ messages in thread
From: Junhao Xie @ 2024-11-08 3:18 UTC (permalink / raw)
To: devicetree, linux-arm-kernel
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner,
Jonas Karlman, Chukun Pan, Junhao Xie, FUKAUMI Naoki,
Dragan Simic, linux-rockchip, linux-kernel, Krzysztof Kozlowski
Add an entry for Ariaboard from Shanghai Novotech
Ariaboard represents a product line from Shanghai Novotech Co., Ltd.
Link: https://shanghainovotech.com/
Link: https://ariaboard.com/
Signed-off-by: Junhao Xie <bigfoot@classfun.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
| 2 ++
1 file changed, 2 insertions(+)
--git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index b320a39de7fe..ddeb4ade4080 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -145,6 +145,8 @@ patternProperties:
description: Arctic Sand
"^arcx,.*":
description: arcx Inc. / Archronix Inc.
+ "^ariaboard,.*":
+ description: Shanghai Novotech Co., Ltd. (Ariaboard)
"^aries,.*":
description: Aries Embedded GmbH
"^arm,.*":
--
2.47.0
^ permalink raw reply [flat|nested] 5+ messages in thread* [PATCH v5 2/3] dt-bindings: arm: rockchip: Add Ariaboard Photonicat RK3568
2024-11-08 3:18 [PATCH v5 0/3] Add support for Ariaboard Photonicat RK3568 Junhao Xie
2024-11-08 3:18 ` [PATCH v5 1/3] dt-bindings: vendor-prefixes: Add prefix for Ariaboard Junhao Xie
@ 2024-11-08 3:18 ` Junhao Xie
2024-11-08 3:18 ` [PATCH v5 3/3] arm64: dts: rockchip: add dts for " Junhao Xie
2024-11-08 15:39 ` [PATCH v5 0/3] Add support " Rob Herring (Arm)
3 siblings, 0 replies; 5+ messages in thread
From: Junhao Xie @ 2024-11-08 3:18 UTC (permalink / raw)
To: devicetree, linux-arm-kernel
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner,
Jonas Karlman, Chukun Pan, Junhao Xie, FUKAUMI Naoki,
Dragan Simic, linux-rockchip, linux-kernel, Krzysztof Kozlowski
This documents Ariaboard Photonicat which is a router based on RK3568 SoC.
Link: https://ariaboard.com/
Link: https://photonicat.com/
Signed-off-by: Junhao Xie <bigfoot@classfun.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
| 5 +++++
1 file changed, 5 insertions(+)
--git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 687823e58c22..28408e08b374 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -49,6 +49,11 @@ properties:
- anbernic,rg-arc-s
- const: rockchip,rk3566
+ - description: Ariaboard Photonicat
+ items:
+ - const: ariaboard,photonicat
+ - const: rockchip,rk3568
+
- description: ArmSoM Sige7 board
items:
- const: armsom,sige7
--
2.47.0
^ permalink raw reply [flat|nested] 5+ messages in thread* [PATCH v5 3/3] arm64: dts: rockchip: add dts for Ariaboard Photonicat RK3568
2024-11-08 3:18 [PATCH v5 0/3] Add support for Ariaboard Photonicat RK3568 Junhao Xie
2024-11-08 3:18 ` [PATCH v5 1/3] dt-bindings: vendor-prefixes: Add prefix for Ariaboard Junhao Xie
2024-11-08 3:18 ` [PATCH v5 2/3] dt-bindings: arm: rockchip: Add Ariaboard Photonicat RK3568 Junhao Xie
@ 2024-11-08 3:18 ` Junhao Xie
2024-11-08 15:39 ` [PATCH v5 0/3] Add support " Rob Herring (Arm)
3 siblings, 0 replies; 5+ messages in thread
From: Junhao Xie @ 2024-11-08 3:18 UTC (permalink / raw)
To: devicetree, linux-arm-kernel
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner,
Jonas Karlman, Chukun Pan, Junhao Xie, FUKAUMI Naoki,
Dragan Simic, linux-rockchip, linux-kernel
Add dts for Ariaboard Photonicat RK3568.
Working IO:
Debug UART
SDIO QCA9377 WiFi and Bluetooth
M.2 E-Key PCIe WiFi and Bluetooth
M.2 B-Key USB Modem WWAN
Ethernet WAN Port
MicroSD Card slot
eMMC
HDMI Output
Mali GPU
USB Type-A
Not working IO:
Ethernet LAN Port (Lack of SGMII support)
Power management MCU on UART4 (Driver pending)
Not working IO in MCU:
Battery voltage sensor
Board temperature sensor
Hardware Power-off
Hardware Watchdog
Network status LED
Real-time clock
USB Charger voltage sensor
About onboard power management MCU:
A heartbeat must be sent to the MCU within 60 seconds,
otherwise the MCU will restart the system.
When powering off, a shutdown command needs to be sent to the MCU.
When the power button is long pressed, the MCU will send a shutdown
command to the system. If system does not shutdown within 60 seconds,
the power will be turned off directly.
MCU only provides voltage for charger and battery.
Manufacturer removed RK8xx PMIC.
Signed-off-by: Junhao Xie <bigfoot@classfun.cn>
---
| 1 +
| 600 ++++++++++++++++++
2 files changed, 601 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
--git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 09423070c992..577bfa6e86d3 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -116,6 +116,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-mecsbc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5c.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5s.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-odroid-m1.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-photonicat.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts433.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-radxa-e25.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-roc-pc.dtb
--git a/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts b/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
new file mode 100644
index 000000000000..940bd7a6160f
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
@@ -0,0 +1,600 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3568.dtsi"
+
+/ {
+ model = "Ariaboard Photonicat";
+ compatible = "ariaboard,photonicat", "rockchip,rk3568";
+
+ aliases {
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ mmc0 = &sdhci;
+ mmc1 = &sdmmc0;
+ mmc2 = &sdmmc1;
+ };
+
+ battery: battery {
+ compatible = "simple-battery";
+ device-chemistry = "lithium-ion";
+ charge-full-design-microamp-hours = <6800000>;
+ energy-full-design-microwatt-hours = <25000000>;
+ voltage-max-design-microvolt = <4200000>;
+ voltage-min-design-microvolt = <3400000>;
+
+ ocv-capacity-celsius = <25>;
+ ocv-capacity-table-0 = <4100000 100>, <4040000 90>,
+ <3980000 80>, <3920000 70>,
+ <3870000 60>, <3820000 50>,
+ <3790000 40>, <3770000 30>,
+ <3740000 20>, <3680000 10>,
+ <3450000 0>;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ hdmi_con: hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ vcca_1v8: regulator-vcca-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcca_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ vccin_5v: regulator-vccin-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "vccin_5v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ /* actually fed by vcc_syson, dependent
+ * on pi6c clock generator
+ */
+ vcc3v3_pcie: regulator-vcc3v3-pcie {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_pcie";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc3v3_pi6c>;
+ };
+
+ /* pi6c pcie clock generator */
+ vcc3v3_pi6c: regulator-vcc3v3-pi6c {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_pwren_h>;
+ regulator-name = "vcc3v3_pi6c";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_syson>;
+ };
+
+ vcc3v3_sd: regulator-vcc3v3-sd {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_pwren>;
+ regulator-boot-on;
+ regulator-name = "vcc3v3_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3>;
+ };
+
+ vcc3v3_sys: regulator-vcc3v3-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_syson>;
+ };
+
+ vcc3v4_rf: regulator-vcc3v4-rf {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rf_pwr_en>;
+ regulator-name = "vcc3v4_rf";
+ regulator-min-microvolt = <3400000>;
+ regulator-max-microvolt = <3400000>;
+ vin-supply = <&vccin_5v>;
+ };
+
+ vcc5v0_usb30_otg0: regulator-vcc5v0-usb30-otg0 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_host_pwren_h>;
+ regulator-name = "vcc5v0_usb30_otg0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vccin_5v>;
+ };
+
+ vcc_sysin: regulator-vcc-sysin {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sysin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vccin_5v>;
+ };
+
+ vcc_syson: regulator-vcc-syson {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_syson";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_sysin>;
+ };
+
+ vcc_1v8: regulator-vcc-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ vcc_3v3: regulator-vcc-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ vdda_0v9: regulator-vdda-0v9 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdda_0v9";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ vdd_gpu: regulator-vdd-gpu {
+ compatible = "pwm-regulator";
+ pwms = <&pwm2 0 5000 1>;
+ pwm-supply = <&vcc_syson>;
+ regulator-name = "vdd_gpu";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-settling-time-up-us = <250>;
+ };
+
+ vdd_logic: regulator-vdd-logic {
+ compatible = "pwm-regulator";
+ pwms = <&pwm1 0 5000 1>;
+ pwm-supply = <&vcc_syson>;
+ regulator-name = "vdd_logic";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-settling-time-up-us = <250>;
+ };
+
+ rfkill-modem {
+ compatible = "rfkill-gpio";
+ label = "M.2 USB Modem";
+ radio-type = "wwan";
+ reset-gpios = <&gpio0 RK_PB0 GPIO_ACTIVE_LOW>;
+ shutdown-gpios = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>;
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&pmucru CLK_RTC_32K>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_reg_on_h &clk32k_out1>;
+ post-power-on-delay-ms = <200>;
+ reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&combphy0 {
+ status = "okay";
+};
+
+&combphy1 {
+ status = "okay";
+};
+
+&combphy2 {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+/* Motorcomm YT8521SC LAN port (require SGMII) */
+&gmac0 {
+ status = "disabled";
+};
+
+/* Motorcomm YT8521SC WAN port */
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
+ assigned-clock-rates = <0>, <125000000>;
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy1>;
+ phy-mode = "rgmii-id";
+ phy-supply = <&vcc_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m1_miim
+ &gmac1m1_tx_bus2
+ &gmac1m1_rx_bus2
+ &gmac1m1_rgmii_clk
+ &gmac1m1_rgmii_bus>;
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&hdmi {
+ avdd-0v9-supply = <&vdda_0v9>;
+ avdd-1v8-supply = <&vcca_1v8>;
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: regulator@1c {
+ compatible = "tcs,tcs4525";
+ reg = <0x1c>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc_syson>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2m1_xfer>;
+ status = "okay";
+};
+
+&i2s0_8ch {
+ status = "okay";
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ð1_phy_rst>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <100000>;
+ reset-gpios = <&gpio4 RK_PC0 GPIO_ACTIVE_LOW>;
+ rx-internal-delay-ps = <1500>;
+ tx-internal-delay-ps = <1500>;
+ };
+};
+
+&pcie30phy {
+ phy-supply = <&vcc3v3_pi6c>;
+ status = "okay";
+};
+
+/* M.2 E-Key for PCIe WLAN */
+&pcie3x2 {
+ max-link-speed = <1>;
+ num-lanes = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie30x1m0_pins>;
+ reset-gpios = <&gpio0 RK_PC3 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie>;
+ status = "okay";
+};
+
+&pinctrl {
+ bt {
+ bt_reg_on_h: bt-reg-on-h {
+ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ ethernet {
+ eth1_phy_rst: eth1-phy-rst {
+ rockchip,pins = <4 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie {
+ pcie_pwren_h: pcie-pwren-h {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdmmc0 {
+ sdmmc0_pwren: sdmmc0-pwren {
+ rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb {
+ rf_pwr_en: rf-pwr-en {
+ rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ usb_host_pwren_h: usb-host-pwren-h {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wifi {
+ wifi_reg_on_h: wifi-reg-on-h {
+ rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio1-supply = <&vcc_3v3>;
+ pmuio2-supply = <&vcc_3v3>;
+ vccio1-supply = <&vcc_3v3>;
+ vccio2-supply = <&vcc_1v8>;
+ vccio3-supply = <&vcc_3v3>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc_3v3>;
+ vccio7-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcca_1v8>;
+ status = "okay";
+};
+
+/* eMMC */
+&sdhci {
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ mmc-hs200-1_8v;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+/* Micro SD card slot */
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ no-1-8-v;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd>;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+/* Qualcomm Atheros QCA9377 WiFi */
+&sdmmc1 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sys>;
+ vqmmc-supply = <&vcc_1v8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ wifi: wifi@1 {
+ reg = <1>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <RK_PB2 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wake";
+ };
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+/* Qualcomm Atheros QCA9377 Bluetooth */
+&uart1 {
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth: bluetooth {
+ compatible = "qcom,qca9377-bt";
+ clocks = <&pmucru CLK_RTC_32K>;
+ clock-names = "lpo";
+ enable-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_reg_on_h>;
+ vddio-supply = <&vcc_1v8>;
+ };
+};
+
+/* Debug UART */
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ dma-names = "tx", "rx";
+ status = "okay";
+};
+
+/* Onboard power management MCU */
+&uart4 {
+ dma-names = "tx", "rx";
+ status = "okay";
+};
+
+/* M.2 E-Key for USB Bluetooth */
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+/* USB Type-A Port */
+&usb_host0_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+/* M.2 B-Key for USB Modem WWAN */
+&usb_host1_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_host {
+ phy-supply = <&vcc3v4_rf>;
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ phy-supply = <&vcc5v0_usb30_otg0>;
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0_usb30_otg0>;
+ status = "okay";
+};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
+
+&xin32k {
+ pinctrl-names = "default";
+ pinctrl-0 = <&clk32k_out1>;
+};
--
2.47.0
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: [PATCH v5 0/3] Add support for Ariaboard Photonicat RK3568
2024-11-08 3:18 [PATCH v5 0/3] Add support for Ariaboard Photonicat RK3568 Junhao Xie
` (2 preceding siblings ...)
2024-11-08 3:18 ` [PATCH v5 3/3] arm64: dts: rockchip: add dts for " Junhao Xie
@ 2024-11-08 15:39 ` Rob Herring (Arm)
3 siblings, 0 replies; 5+ messages in thread
From: Rob Herring (Arm) @ 2024-11-08 15:39 UTC (permalink / raw)
To: Junhao Xie
Cc: Dragan Simic, Conor Dooley, Heiko Stuebner, Krzysztof Kozlowski,
devicetree, linux-rockchip, linux-arm-kernel, FUKAUMI Naoki,
Jonas Karlman, linux-kernel, Chukun Pan
On Fri, 08 Nov 2024 11:18:44 +0800, Junhao Xie wrote:
> Add dts for Ariaboard Photonicat RK3568.
>
> This series bring support for:
> * Debug UART
> * SDIO QCA9377 WiFi and Bluetooth
> * M.2 E-Key PCIe WiFi and Bluetooth
> * M.2 B-Key USB Modem WWAN
> * Ethernet WAN Port
> * MicroSD Card slot
> * eMMC
> * HDMI Output
> * Mali GPU
> * USB Type-A
>
> Changed from v1:
> - move some general nodes (firmware, ramoops, reboot-mode) to rk356x.dtsi
> - gmac1 change to phy-mode rgmii-id
> - corrected some regulator to be closer to schematics
> - rename rk3568-ariaboard-photonicat.dts to rk3568-photonicat.dts
> https://lore.kernel.org/lkml/20240904111456.87089-1-bigfoot@classfun.cn/
>
> Changed from v2:
> - remove unused headers
> - corrected some regulator to be closer to schematics
> - remove usb_host1_ohci, usb_host1_ehci, usb2phy1_host that have no connection
> https://lore.kernel.org/lkml/20240906045706.1004813-1-bigfoot@classfun.cn/
>
> Changed from v3:
> - corrected some regulator to be closer to schematics
> - changed to using clk32k_out1 in xin32k
> https://lore.kernel.org/lkml/20240911122809.1789778-2-bigfoot@classfun.cn/
>
> Changed from v4:
> - corrected some regulator to be closer to schematics
> - corrected some label to match node name
> - use resets props in phy node instead deprecated snps,reset-gpio
> https://lore.kernel.org/lkml/20240914145549.879936-1-bigfoot@classfun.cn/
>
> Junhao Xie (3):
> dt-bindings: vendor-prefixes: Add prefix for Ariaboard
> dt-bindings: arm: rockchip: Add Ariaboard Photonicat RK3568
> arm64: dts: rockchip: add dts for Ariaboard Photonicat RK3568
>
> .../devicetree/bindings/arm/rockchip.yaml | 5 +
> .../devicetree/bindings/vendor-prefixes.yaml | 2 +
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3568-photonicat.dts | 600 ++++++++++++++++++
> 4 files changed, 608 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
>
> --
> 2.47.0
>
>
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y rockchip/rk3568-photonicat.dtb' for 20241108031847.700606-1-bigfoot@classfun.cn:
arch/arm64/boot/dts/rockchip/rk3568-photonicat.dtb: bluetooth: 'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml#
arch/arm64/boot/dts/rockchip/rk3568-photonicat.dtb: phy@fe8c0000: 'phy-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/phy/rockchip,pcie3-phy.yaml#
arch/arm64/boot/dts/rockchip/rk3568-photonicat.dtb: rfkill-modem: 'reset-gpios' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/net/rfkill-gpio.yaml#
^ permalink raw reply [flat|nested] 5+ messages in thread