From: Adrian Hunter <adrian.hunter@intel.com>
To: Sarthak Garg <quic_sartgarg@quicinc.com>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Ulf Hansson <ulf.hansson@linaro.org>
Cc: <linux-arm-msm@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <linux-mmc@vger.kernel.org>,
<quic_cang@quicinc.com>, <quic_nguyenb@quicinc.com>,
<quic_rampraka@quicinc.com>, <quic_pragalla@quicinc.com>,
<quic_sayalil@quicinc.com>, <quic_nitirawa@quicinc.com>,
<quic_bhaskarv@quicinc.com>
Subject: Re: [PATCH V2 1/3] mmc: sdhci-msm: Enable tuning for SDR50 mode for SD card
Date: Wed, 28 May 2025 14:32:20 +0300 [thread overview]
Message-ID: <177e21cc-0a9b-4543-8135-f4da424f5713@intel.com> (raw)
In-Reply-To: <20250523105745.6210-2-quic_sartgarg@quicinc.com>
On 23/05/2025 13:57, Sarthak Garg wrote:
> For Qualcomm SoCs which needs level shifter for SD card, extra delay is
> seen on receiver data path.
>
> To compensate this delay enable tuning for SDR50 mode for targets which
> has level shifter. SDHCI_SDR50_NEEDS_TUNING caps will be set for targets
> with level shifter on Qualcomm SOC's.
>
> Signed-off-by: Sarthak Garg <quic_sartgarg@quicinc.com>
Assuming this is still needed even with new generic quirk approach:
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
> ---
> drivers/mmc/host/sdhci-msm.c | 15 +++++++++++++++
> 1 file changed, 15 insertions(+)
>
> diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
> index 66c0d1ba2a33..bf91cb96a0ea 100644
> --- a/drivers/mmc/host/sdhci-msm.c
> +++ b/drivers/mmc/host/sdhci-msm.c
> @@ -81,6 +81,7 @@
> #define CORE_IO_PAD_PWR_SWITCH_EN BIT(15)
> #define CORE_IO_PAD_PWR_SWITCH BIT(16)
> #define CORE_HC_SELECT_IN_EN BIT(18)
> +#define CORE_HC_SELECT_IN_SDR50 (4 << 19)
> #define CORE_HC_SELECT_IN_HS400 (6 << 19)
> #define CORE_HC_SELECT_IN_MASK (7 << 19)
>
> @@ -1133,6 +1134,10 @@ static bool sdhci_msm_is_tuning_needed(struct sdhci_host *host)
> {
> struct mmc_ios *ios = &host->mmc->ios;
>
> + if (ios->timing == MMC_TIMING_UHS_SDR50 &&
> + host->flags & SDHCI_SDR50_NEEDS_TUNING)
> + return true;
> +
> /*
> * Tuning is required for SDR104, HS200 and HS400 cards and
> * if clock frequency is greater than 100MHz in these modes.
> @@ -1201,6 +1206,8 @@ static int sdhci_msm_execute_tuning(struct mmc_host *mmc, u32 opcode)
> struct mmc_ios ios = host->mmc->ios;
> struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
> + const struct sdhci_msm_offset *msm_offset = msm_host->offset;
> + u32 config;
>
> if (!sdhci_msm_is_tuning_needed(host)) {
> msm_host->use_cdr = false;
> @@ -1217,6 +1224,14 @@ static int sdhci_msm_execute_tuning(struct mmc_host *mmc, u32 opcode)
> */
> msm_host->tuning_done = 0;
>
> + if (ios.timing == MMC_TIMING_UHS_SDR50 &&
> + host->flags & SDHCI_SDR50_NEEDS_TUNING) {
> + config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec);
> + config &= ~CORE_HC_SELECT_IN_MASK;
> + config |= CORE_HC_SELECT_IN_EN | CORE_HC_SELECT_IN_SDR50;
> + writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec);
> + }
> +
> /*
> * For HS400 tuning in HS200 timing requires:
> * - select MCLK/2 in VENDOR_SPEC
next prev parent reply other threads:[~2025-05-28 11:32 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-05-23 10:57 [PATCH V2 0/3] Add level shifter support for qualcomm SOC's Sarthak Garg
2025-05-23 10:57 ` [PATCH V2 1/3] mmc: sdhci-msm: Enable tuning for SDR50 mode for SD card Sarthak Garg
2025-05-28 11:32 ` Adrian Hunter [this message]
2025-05-23 10:57 ` [PATCH V2 2/3] mmc: sdhci-msm: Limit HS mode frequency to 37.5MHz Sarthak Garg
2025-05-23 10:57 ` [PATCH V2 3/3] arm64: dts: qcom: sm8550: Remove SDR104/SDR50 broken caps Sarthak Garg
2025-05-23 18:25 ` [PATCH V2 0/3] Add level shifter support for qualcomm SOC's Konrad Dybcio
2025-05-27 14:35 ` Ulf Hansson
2025-06-16 7:14 ` Sarthak Garg
2025-06-16 7:13 ` Sarthak Garg
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=177e21cc-0a9b-4543-8135-f4da424f5713@intel.com \
--to=adrian.hunter@intel.com \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=quic_bhaskarv@quicinc.com \
--cc=quic_cang@quicinc.com \
--cc=quic_nguyenb@quicinc.com \
--cc=quic_nitirawa@quicinc.com \
--cc=quic_pragalla@quicinc.com \
--cc=quic_rampraka@quicinc.com \
--cc=quic_sartgarg@quicinc.com \
--cc=quic_sayalil@quicinc.com \
--cc=robh@kernel.org \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®