* [PATCH v9 1/3] arm64: dts: ti: k3-j7200: Add gpio nodes
2021-03-26 6:41 [PATCH v9 0/3] J7200: Add support for GPIO and higher speed modes in MMCSD subsystems Aswath Govindraju
@ 2021-03-26 6:41 ` Aswath Govindraju
2021-03-26 6:41 ` [PATCH v9 2/3] arm64: dts: ti: k3-j7200-common-proc-board: Disable unused gpio modules Aswath Govindraju
` (2 subsequent siblings)
3 siblings, 0 replies; 6+ messages in thread
From: Aswath Govindraju @ 2021-03-26 6:41 UTC (permalink / raw)
Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I,
Aswath Govindraju, Faiz Abbas, Sekhar Nori, Nishanth Menon,
Tero Kristo, Rob Herring, linux-arm-kernel, devicetree,
linux-kernel
From: Faiz Abbas <faiz_abbas@ti.com>
There are 4 instances of gpio modules in main domain:
gpio0, gpio2, gpio4 and gpio6
Groups are created to provide protection between different processor
virtual worlds. Each of these modules I/O pins are muxed within the
group. Exactly one module can be selected to control the corresponding
pin by selecting it in the pad mux configuration registers.
This group in main domain pins out 69 lines (5 banks). Add DT modes for
each module instance in the main domain.
Similar to the gpio groups in main domain, there is one gpio group in
wakeup domain with 2 module instances in it.
The gpio group pins out 72 pins (6 banks) of the first 85 gpio lines. Add
DT nodes for each module instance in the wakeup domain.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 72 +++++++++++++++++++
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 34 +++++++++
2 files changed, 106 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index 17477ab0fd8e..e60650a62b14 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -672,6 +672,78 @@
};
};
+ main_gpio0: gpio@600000 {
+ compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x00600000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&main_gpio_intr>;
+ interrupts = <145>, <146>, <147>, <148>,
+ <149>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ ti,ngpio = <69>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 105 0>;
+ clock-names = "gpio";
+ };
+
+ main_gpio2: gpio@610000 {
+ compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x00610000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&main_gpio_intr>;
+ interrupts = <154>, <155>, <156>, <157>,
+ <158>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ ti,ngpio = <69>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 107 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 107 0>;
+ clock-names = "gpio";
+ };
+
+ main_gpio4: gpio@620000 {
+ compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x00620000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&main_gpio_intr>;
+ interrupts = <163>, <164>, <165>, <166>,
+ <167>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ ti,ngpio = <69>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 109 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 109 0>;
+ clock-names = "gpio";
+ };
+
+ main_gpio6: gpio@630000 {
+ compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x00630000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&main_gpio_intr>;
+ interrupts = <172>, <173>, <174>, <175>,
+ <176>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ ti,ngpio = <69>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 111 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 111 0>;
+ clock-names = "gpio";
+ };
+
main_r5fss0: r5fss@5c00000 {
compatible = "ti,j7200-r5fss";
ti,cluster-mode = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 5408ec815d58..4e4ea7655fe2 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -107,6 +107,40 @@
ti,interrupt-ranges = <16 960 16>;
};
+ wkup_gpio0: gpio@42110000 {
+ compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x42110000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&wkup_gpio_intr>;
+ interrupts = <103>, <104>, <105>, <106>, <107>, <108>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ ti,ngpio = <85>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 113 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 113 0>;
+ clock-names = "gpio";
+ };
+
+ wkup_gpio1: gpio@42100000 {
+ compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x42100000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&wkup_gpio_intr>;
+ interrupts = <112>, <113>, <114>, <115>, <116>, <117>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ ti,ngpio = <85>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 114 0>;
+ clock-names = "gpio";
+ };
+
mcu_navss: bus@28380000 {
compatible = "simple-mfd";
#address-cells = <2>;
--
2.17.1
^ permalink raw reply [flat|nested] 6+ messages in thread* [PATCH v9 2/3] arm64: dts: ti: k3-j7200-common-proc-board: Disable unused gpio modules
2021-03-26 6:41 [PATCH v9 0/3] J7200: Add support for GPIO and higher speed modes in MMCSD subsystems Aswath Govindraju
2021-03-26 6:41 ` [PATCH v9 1/3] arm64: dts: ti: k3-j7200: Add gpio nodes Aswath Govindraju
@ 2021-03-26 6:41 ` Aswath Govindraju
2021-03-26 6:41 ` [PATCH v9 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems Aswath Govindraju
2021-03-26 23:24 ` [PATCH v9 0/3] J7200: Add support for GPIO and higher speed modes in " Nishanth Menon
3 siblings, 0 replies; 6+ messages in thread
From: Aswath Govindraju @ 2021-03-26 6:41 UTC (permalink / raw)
Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I,
Aswath Govindraju, Faiz Abbas, Sekhar Nori, Nishanth Menon,
Tero Kristo, Rob Herring, linux-arm-kernel, devicetree,
linux-kernel
From: Faiz Abbas <faiz_abbas@ti.com>
There are 6 gpio instances inside SoC with 2 groups as show below:
Group one: wkup_gpio0, wkup_gpio1
Group two: main_gpio0, main_gpio2, main_gpio4, main_gpio6
Only one instance from each group can be used at a time. So use main_gpio0
and wkup_gpio0 in current linux context and disable the rest of the nodes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
.../boot/dts/ti/k3-j7200-common-proc-board.dts | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 4a7182abccf5..b493f939b09a 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -122,6 +122,22 @@
status = "disabled";
};
+&main_gpio2 {
+ status = "disabled";
+};
+
+&main_gpio4 {
+ status = "disabled";
+};
+
+&main_gpio6 {
+ status = "disabled";
+};
+
+&wkup_gpio1 {
+ status = "disabled";
+};
+
&mcu_cpsw {
pinctrl-names = "default";
pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
--
2.17.1
^ permalink raw reply [flat|nested] 6+ messages in thread* [PATCH v9 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems
2021-03-26 6:41 [PATCH v9 0/3] J7200: Add support for GPIO and higher speed modes in MMCSD subsystems Aswath Govindraju
2021-03-26 6:41 ` [PATCH v9 1/3] arm64: dts: ti: k3-j7200: Add gpio nodes Aswath Govindraju
2021-03-26 6:41 ` [PATCH v9 2/3] arm64: dts: ti: k3-j7200-common-proc-board: Disable unused gpio modules Aswath Govindraju
@ 2021-03-26 6:41 ` Aswath Govindraju
2021-03-26 13:43 ` Kishon Vijay Abraham I
2021-03-26 23:24 ` [PATCH v9 0/3] J7200: Add support for GPIO and higher speed modes in " Nishanth Menon
3 siblings, 1 reply; 6+ messages in thread
From: Aswath Govindraju @ 2021-03-26 6:41 UTC (permalink / raw)
Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I,
Aswath Govindraju, Nishanth Menon, Tero Kristo, Rob Herring,
linux-arm-kernel, devicetree, linux-kernel
The following speed modes are now supported in J7200 SoC,
- HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
- UHS-I speed modes in MMCSD1 subsystem [1].
Add support for UHS-I modes by adding voltage regulator device tree nodes
and corresponding pinmux details, to power cycle and voltage switch cards.
Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
device tree nodes.
Also update the delay values for various speed modes supported, based on
the revised january 2021 J7200 datasheet[2].
[1] - section 12.3.6.1.1 MMCSD Features, in
https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf,
(SPRUIU1A – JULY 2020 – REVISED JANUARY 2021)
[2] - https://www.ti.com/lit/ds/symlink/dra821u.pdf,
(SPRSP57B – APRIL 2020 – REVISED JANUARY 2021)
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 78 +++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 14 +++-
2 files changed, 90 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index b493f939b09a..bedd01b7a32c 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -16,6 +16,65 @@
stdout-path = "serial2:115200n8";
bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
};
+
+ evm_12v0: fixedregulator-evm12v0 {
+ /* main supply */
+ compatible = "regulator-fixed";
+ regulator-name = "evm_12v0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vsys_3v3: fixedregulator-vsys3v3 {
+ /* Output of LM5140 */
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&evm_12v0>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vsys_5v0: fixedregulator-vsys5v0 {
+ /* Output of LM5140 */
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&evm_12v0>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_mmc1: fixedregulator-sd {
+ /* Output of TPS22918 */
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ vin-supply = <&vsys_3v3>;
+ gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv: gpio-regulator-TLV71033 {
+ /* Output of TLV71033 */
+ compatible = "regulator-gpio";
+ regulator-name = "tlv71033";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_pins_default>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ vin-supply = <&vsys_5v0>;
+ gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ };
};
&wkup_pmx0 {
@@ -45,6 +104,13 @@
};
&main_pmx0 {
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
+ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
+ >;
+ };
+
main_i2c1_pins_default: main-i2c1-pins-default {
pinctrl-single,pins = <
J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
@@ -70,6 +136,12 @@
J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>;
};
+
+ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
+ >;
+ };
};
&wkup_uart0 {
@@ -157,6 +229,10 @@
};
&main_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+
exp1: gpio@20 {
compatible = "ti,tca6416";
reg = <0x20>;
@@ -206,6 +282,8 @@
/* SD card */
pinctrl-0 = <&main_mmc1_pins_default>;
pinctrl-names = "default";
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv>;
ti,driver-strength-ohm = <50>;
disable-wp;
};
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index e60650a62b14..f86c493a44f1 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -512,11 +512,16 @@
ti,otap-del-sel-mmc-hs = <0x0>;
ti,otap-del-sel-ddr52 = <0x6>;
ti,otap-del-sel-hs200 = <0x8>;
- ti,otap-del-sel-hs400 = <0x0>;
+ ti,otap-del-sel-hs400 = <0x5>;
+ ti,itap-del-sel-legacy = <0x10>;
+ ti,itap-del-sel-mmc-hs = <0xa>;
ti,strobe-sel = <0x77>;
+ ti,clkbuf-sel = <0x7>;
ti,trm-icp = <0x8>;
bus-width = <8>;
mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
dma-coherent;
};
@@ -534,7 +539,12 @@
ti,otap-del-sel-sdr50 = <0xc>;
ti,otap-del-sel-sdr104 = <0x5>;
ti,otap-del-sel-ddr50 = <0xc>;
- no-1-8-v;
+ ti,itap-del-sel-legacy = <0x0>;
+ ti,itap-del-sel-sd-hs = <0x0>;
+ ti,itap-del-sel-sdr12 = <0x0>;
+ ti,itap-del-sel-sdr25 = <0x0>;
+ ti,clkbuf-sel = <0x7>;
+ ti,trm-icp = <0x8>;
dma-coherent;
};
--
2.17.1
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: [PATCH v9 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems
2021-03-26 6:41 ` [PATCH v9 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems Aswath Govindraju
@ 2021-03-26 13:43 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 6+ messages in thread
From: Kishon Vijay Abraham I @ 2021-03-26 13:43 UTC (permalink / raw)
To: Aswath Govindraju
Cc: Vignesh Raghavendra, Lokesh Vutla, Nishanth Menon, Tero Kristo,
Rob Herring, linux-arm-kernel, devicetree, linux-kernel
Hi,
On 26/03/21 12:11 pm, Aswath Govindraju wrote:
> The following speed modes are now supported in J7200 SoC,
> - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
> - UHS-I speed modes in MMCSD1 subsystem [1].
>
> Add support for UHS-I modes by adding voltage regulator device tree nodes
> and corresponding pinmux details, to power cycle and voltage switch cards.
> Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
> device tree nodes.
>
> Also update the delay values for various speed modes supported, based on
> the revised january 2021 J7200 datasheet[2].
>
> [1] - section 12.3.6.1.1 MMCSD Features, in
> https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf,
> (SPRUIU1A – JULY 2020 – REVISED JANUARY 2021)
>
> [2] - https://www.ti.com/lit/ds/symlink/dra821u.pdf,
> (SPRSP57B – APRIL 2020 – REVISED JANUARY 2021)
>
> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
> Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Thanks! Patch looks good to me.
Regards
Kishon
> ---
> .../dts/ti/k3-j7200-common-proc-board.dts | 78 +++++++++++++++++++
> arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 14 +++-
> 2 files changed, 90 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> index b493f939b09a..bedd01b7a32c 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> @@ -16,6 +16,65 @@
> stdout-path = "serial2:115200n8";
> bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
> };
> +
> + evm_12v0: fixedregulator-evm12v0 {
> + /* main supply */
> + compatible = "regulator-fixed";
> + regulator-name = "evm_12v0";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vsys_3v3: fixedregulator-vsys3v3 {
> + /* Output of LM5140 */
> + compatible = "regulator-fixed";
> + regulator-name = "vsys_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&evm_12v0>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vsys_5v0: fixedregulator-vsys5v0 {
> + /* Output of LM5140 */
> + compatible = "regulator-fixed";
> + regulator-name = "vsys_5v0";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&evm_12v0>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vdd_mmc1: fixedregulator-sd {
> + /* Output of TPS22918 */
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_mmc1";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + enable-active-high;
> + vin-supply = <&vsys_3v3>;
> + gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
> + };
> +
> + vdd_sd_dv: gpio-regulator-TLV71033 {
> + /* Output of TLV71033 */
> + compatible = "regulator-gpio";
> + regulator-name = "tlv71033";
> + pinctrl-names = "default";
> + pinctrl-0 = <&vdd_sd_dv_pins_default>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + vin-supply = <&vsys_5v0>;
> + gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
> + states = <1800000 0x0>,
> + <3300000 0x1>;
> + };
> };
>
> &wkup_pmx0 {
> @@ -45,6 +104,13 @@
> };
>
> &main_pmx0 {
> + main_i2c0_pins_default: main-i2c0-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
> + J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
> + >;
> + };
> +
> main_i2c1_pins_default: main-i2c1-pins-default {
> pinctrl-single,pins = <
> J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
> @@ -70,6 +136,12 @@
> J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
> >;
> };
> +
> + vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
> + >;
> + };
> };
>
> &wkup_uart0 {
> @@ -157,6 +229,10 @@
> };
>
> &main_i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c0_pins_default>;
> + clock-frequency = <400000>;
> +
> exp1: gpio@20 {
> compatible = "ti,tca6416";
> reg = <0x20>;
> @@ -206,6 +282,8 @@
> /* SD card */
> pinctrl-0 = <&main_mmc1_pins_default>;
> pinctrl-names = "default";
> + vmmc-supply = <&vdd_mmc1>;
> + vqmmc-supply = <&vdd_sd_dv>;
> ti,driver-strength-ohm = <50>;
> disable-wp;
> };
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> index e60650a62b14..f86c493a44f1 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> @@ -512,11 +512,16 @@
> ti,otap-del-sel-mmc-hs = <0x0>;
> ti,otap-del-sel-ddr52 = <0x6>;
> ti,otap-del-sel-hs200 = <0x8>;
> - ti,otap-del-sel-hs400 = <0x0>;
> + ti,otap-del-sel-hs400 = <0x5>;
> + ti,itap-del-sel-legacy = <0x10>;
> + ti,itap-del-sel-mmc-hs = <0xa>;
> ti,strobe-sel = <0x77>;
> + ti,clkbuf-sel = <0x7>;
> ti,trm-icp = <0x8>;
> bus-width = <8>;
> mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> dma-coherent;
> };
>
> @@ -534,7 +539,12 @@
> ti,otap-del-sel-sdr50 = <0xc>;
> ti,otap-del-sel-sdr104 = <0x5>;
> ti,otap-del-sel-ddr50 = <0xc>;
> - no-1-8-v;
> + ti,itap-del-sel-legacy = <0x0>;
> + ti,itap-del-sel-sd-hs = <0x0>;
> + ti,itap-del-sel-sdr12 = <0x0>;
> + ti,itap-del-sel-sdr25 = <0x0>;
> + ti,clkbuf-sel = <0x7>;
> + ti,trm-icp = <0x8>;
> dma-coherent;
> };
>
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v9 0/3] J7200: Add support for GPIO and higher speed modes in MMCSD subsystems
2021-03-26 6:41 [PATCH v9 0/3] J7200: Add support for GPIO and higher speed modes in MMCSD subsystems Aswath Govindraju
` (2 preceding siblings ...)
2021-03-26 6:41 ` [PATCH v9 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems Aswath Govindraju
@ 2021-03-26 23:24 ` Nishanth Menon
3 siblings, 0 replies; 6+ messages in thread
From: Nishanth Menon @ 2021-03-26 23:24 UTC (permalink / raw)
To: Aswath Govindraju
Cc: Nishanth Menon, Tero Kristo, Vignesh Raghavendra,
Kishon Vijay Abraham I, devicetree, linux-arm-kernel,
Lokesh Vutla, Rob Herring, linux-kernel
On Fri, 26 Mar 2021 12:11:17 +0530, Aswath Govindraju wrote:
> The following series of patches
> - Add support for GPIO subsystem in main and wakeup domains.
> - Add voltage regulator device tree nodes and their corresponding pinmux
> to support power cycle and voltage switch required for UHS-I modes
> - sets respective tags in sdhci0 node to support higher speeds
> - remove no-1-8-v tag from sdhci1 node to support UHS-I modes
> - Update delay values for various speed modes supported.
>
> [...]
Hi Aswath Govindraju,
I have applied the following to branch ti-k3-dts-next on [1].
Thank you!
[1/3] arm64: dts: ti: k3-j7200: Add gpio nodes
commit: e0b2e6af39ea94a6fdba53571e6711df49b6ee8d
[2/3] arm64: dts: ti: k3-j7200-common-proc-board: Disable unused gpio modules
commit: f4cc7daf460b285d3b318496654dab01472df8e4
[3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems
commit: 9437499086c24abf298bc3c3a053faedfc19bab1
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
[1] git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux.git
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
^ permalink raw reply [flat|nested] 6+ messages in thread