[PATCH 0/4] arm64: dts: qcom: ipq5018: add Ubiquiti UniFi U6 Enterprise

[PATCH 0/4] arm64: dts: qcom: ipq5018: add Ubiquiti UniFi U6 Enterprise

[Andrei-Alexandru Bleortu]

Add the Ubiquiti UniFi U6 Enterprise, an IPQ5018 access point with two
QCN9074 radios on PCIe (5 GHz and 6 GHz). The first patch documents the
QCN9074's PCI ID in the ath11k PCI binding, so the radios' nodes can
carry the calibration variants their board data is looked up by; the
third labels the PCIe1 root port the way PCIe0's already is.

The Ethernet port (GMAC1 with a QCA8081 PHY) and the IPQ5018's own
2.4 GHz radio are left out until the GMAC and the WCSS remoteproc have
bindings.

The vendor U-Boot only boots Ubiquiti-signed images, so the board was
booted by chainloading from it. Tested on hardware with Linux 7.2 and
the out-of-tree board description these nodes come from: both QCN9074
radios come up with ath11k and their board data selected by these variants,
and the eMMC and the SPI NOR (including U-Boot environment writes) are
in use. The reset button and the accelerometer are described as in the
vendor device tree and were not exercised.

Patch 1 is for the ath11k binding; the rest go through the qcom tree.

The patches were written with an AI coding assistant (Claude Code),
which also drafted the changelogs; the testing above was done on the
device.

Andrei-Alexandru Bleortu (4):
  dt-bindings: net: wireless: qcom,ath11k-pci: add QCN9074
  dt-bindings: arm: qcom: add Ubiquiti UniFi U6 Enterprise
  arm64: dts: qcom: ipq5018: label the PCIe1 root port
  arm64: dts: qcom: ipq5018: add Ubiquiti UniFi U6 Enterprise

 .../devicetree/bindings/arm/qcom.yaml         |   1 +
 .../net/wireless/qcom,ath11k-pci.yaml         |   1 +
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../dts/qcom/ipq5018-ubnt-u6-enterprise.dts   | 236 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/ipq5018.dtsi         |   2 +-
 5 files changed, 240 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/boot/dts/qcom/ipq5018-ubnt-u6-enterprise.dts

-- 
2.47.3

[PATCH 1/4] dt-bindings: net: wireless: qcom,ath11k-pci: add QCN9074

[Andrei-Alexandru Bleortu]

QCN9074 is a PCIe 802.11ax radio that boards such as the IPQ5018-based
Ubiquiti UniFi U6 Enterprise solder down, two of them on different
bands. Like the other ath11k PCIe devices, each needs
qcom,calibration-variant to select its board data. Document its PCI ID.

No supplies are added: on these boards the radio's rails are fixed and
not under software control.

Assisted-by: LLM
Signed-off-by: Andrei-Alexandru Bleortu <me@andrei-z.com>
---
 .../devicetree/bindings/net/wireless/qcom,ath11k-pci.yaml        | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath11k-pci.yaml b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k-pci.yaml
index 0162e3657..605ac5e01 100644
--- a/Documentation/devicetree/bindings/net/wireless/qcom,ath11k-pci.yaml
+++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k-pci.yaml
@@ -18,6 +18,7 @@ properties:
     enum:
       - pci17cb,1101  # QCA6390
       - pci17cb,1103  # WCN6855
+      - pci17cb,1104  # QCN9074
 
   reg:
     maxItems: 1
-- 
2.47.3

Re: [PATCH 1/4] dt-bindings: net: wireless: qcom,ath11k-pci: add QCN9074

[Krzysztof Kozlowski]

On 03/10/2026 10:34, Andrei-Alexandru Bleortu wrote:
> QCN9074 is a PCIe 802.11ax radio that boards such as the IPQ5018-based
> Ubiquiti UniFi U6 Enterprise solder down, two of them on different
> bands. Like the other ath11k PCIe devices, each needs
> qcom,calibration-variant to select its board data. Document its PCI ID.
> 
> No supplies are added: on these boards the radio's rails are fixed and
> not under software control.
> 
> Assisted-by: LLM
> Signed-off-by: Andrei-Alexandru Bleortu <me@andrei-z.com>
> ---


Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

Best regards,
Krzysztof

[PATCH 2/4] dt-bindings: arm: qcom: add Ubiquiti UniFi U6 Enterprise

[Andrei-Alexandru Bleortu]

Document the Ubiquiti UniFi U6 Enterprise, an IPQ5018 based access
point.

Assisted-by: LLM
Signed-off-by: Andrei-Alexandru Bleortu <me@andrei-z.com>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 121ca557c..4524f76b4 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -113,6 +113,7 @@ properties:
           - enum:
               - qcom,ipq5018-rdp432-c2
               - tplink,archer-ax55-v1
+              - ubnt,u6-enterprise
           - const: qcom,ipq5018
 
       - items:
-- 
2.47.3

Re: [PATCH 2/4] dt-bindings: arm: qcom: add Ubiquiti UniFi U6 Enterprise

[Krzysztof Kozlowski]

On 03/10/2026 10:34, Andrei-Alexandru Bleortu wrote:
> Document the Ubiquiti UniFi U6 Enterprise, an IPQ5018 based access
> point.
> 
> Assisted-by: LLM

I am still surprised people use LLM for such single liners.

> Signed-off-by: Andrei-Alexandru Bleortu <me@andrei-z.com>


Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

Best regards,
Krzysztof

[PATCH 3/4] arm64: dts: qcom: ipq5018: label the PCIe1 root port

[Andrei-Alexandru Bleortu]

The root port of pcie0 has a label, the one of pcie1 has none, so a
board cannot attach its PERST# GPIO or a device below it the same way.
Add pcie1_port0.

Assisted-by: LLM
Signed-off-by: Andrei-Alexandru Bleortu <me@andrei-z.com>
---
 arch/arm64/boot/dts/qcom/ipq5018.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
index fe1ed240d..2f3bcfa88 100644
--- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
@@ -838,7 +838,7 @@ pcie1: pcie@80000000 {
 
 			status = "disabled";
 
-			pcie@0 {
+			pcie1_port0: pcie@0 {
 				device_type = "pci";
 				reg = <0x0 0x0 0x0 0x0 0x0>;
 				bus-range = <0x01 0xff>;
-- 
2.47.3

Re: [PATCH 3/4] arm64: dts: qcom: ipq5018: label the PCIe1 root port

[Krzysztof Kozlowski]

On 03/10/2026 10:34, Andrei-Alexandru Bleortu wrote:
> The root port of pcie0 has a label, the one of pcie1 has none, so a

This is pointless commit. The label does not end up in DTB and there is
no user of it.

Drop or squash.


Best regards,
Krzysztof

[PATCH 4/4] arm64: dts: qcom: ipq5018: add Ubiquiti UniFi U6 Enterprise

[Andrei-Alexandru Bleortu]

The Ubiquiti UniFi U6 Enterprise is a ceiling-mount Wi-Fi 6E access point:

- SoC: Qualcomm IPQ5018
- RAM: 1 GiB
- Flash: SPI NOR (boot chain) and eMMC
- 5 GHz: QCN9074 on PCIe0
- 6 GHz: QCN9074 on PCIe1
- Ethernet: one 2.5GbE PoE port, a QCA8081 PHY behind GMAC1
- Accelerometer: ST LIS2DH12
- Button: reset

Describe what mainline supports today. The Ethernet port and the
IPQ5018's own 2.4 GHz radio are left out until the GMAC and the WCSS
remoteproc have bindings; the LED controller and the board MCU on the
I2C bus have none. The QCN9074s carry the calibration variants their
board data is looked up by. The vendor QSEE reserves 4 MiB, twice the
SoC default.

Assisted-by: LLM
Signed-off-by: Andrei-Alexandru Bleortu <me@andrei-z.com>
---
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../dts/qcom/ipq5018-ubnt-u6-enterprise.dts   | 236 ++++++++++++++++++
 2 files changed, 237 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/ipq5018-ubnt-u6-enterprise.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 88230c4e0..aca7d8e41 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -32,6 +32,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= hamoa-lenovo-ideacentre-mini-01q8x10.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= hawi-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq5018-rdp432-c2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq5018-tplink-archer-ax55-v1.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= ipq5018-ubnt-u6-enterprise.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq5210-rdp504.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq5332-rdp441.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq5332-rdp442.dtb
diff --git a/arch/arm64/boot/dts/qcom/ipq5018-ubnt-u6-enterprise.dts b/arch/arm64/boot/dts/qcom/ipq5018-ubnt-u6-enterprise.dts
new file mode 100644
index 000000000..6462f99df
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq5018-ubnt-u6-enterprise.dts
@@ -0,0 +1,236 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ipq5018.dtsi"
+
+/ {
+	model = "Ubiquiti UniFi U6 Enterprise";
+	compatible = "ubnt,u6-enterprise", "qcom,ipq5018";
+
+	aliases {
+		serial0 = &blsp1_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		button-reset {
+			label = "reset";
+			gpios = <&tlmm 24 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+};
+
+&blsp1_i2c3 {
+	pinctrl-0 = <&i2c_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	accelerometer@18 {
+		compatible = "st,lis2dh12-accel";
+		reg = <0x18>;
+	};
+};
+
+&blsp1_spi1 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "0:sbl1";
+				reg = <0x000000 0x030000>;
+				read-only;
+			};
+
+			partition@30000 {
+				label = "0:mibib";
+				reg = <0x030000 0x010000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "0:bootconfig";
+				reg = <0x040000 0x010000>;
+				read-only;
+			};
+
+			partition@50000 {
+				label = "0:qsee";
+				reg = <0x050000 0x0a0000>;
+				read-only;
+			};
+
+			partition@f0000 {
+				label = "0:devcfg";
+				reg = <0x0f0000 0x010000>;
+				read-only;
+			};
+
+			partition@100000 {
+				label = "0:cdt";
+				reg = <0x100000 0x010000>;
+				read-only;
+			};
+
+			partition@110000 {
+				label = "0:appsblenv";
+				reg = <0x110000 0x010000>;
+			};
+
+			partition@120000 {
+				label = "0:appsbl";
+				reg = <0x120000 0x0a0000>;
+				read-only;
+			};
+
+			partition@1c0000 {
+				label = "0:art";
+				reg = <0x1c0000 0x070000>;
+				read-only;
+			};
+
+			partition@230000 {
+				label = "eeprom";
+				reg = <0x230000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+/* The bootloader muxes the console pins; GPIO33/34 are I2C on this board. */
+&blsp1_uart1 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie0_phy {
+	status = "okay";
+};
+
+&pcie0_port0 {
+	reset-gpios = <&tlmm 15 GPIO_ACTIVE_LOW>;
+
+	wifi@0,0 {
+		compatible = "pci17cb,1104";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+		qcom,calibration-variant = "Ubiquiti-U6-Enterprise-5G";
+	};
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pcie1_phy {
+	status = "okay";
+};
+
+&pcie1_port0 {
+	reset-gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+
+	wifi@0,0 {
+		compatible = "pci17cb,1104";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+		qcom,calibration-variant = "Ubiquiti-U6-Enterprise-6G";
+	};
+};
+
+&prng {
+	status = "okay";
+};
+
+&sdhc_1 {
+	pinctrl-0 = <&emmc_pins>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&sleep_clk {
+	clock-frequency = <32000>;
+};
+
+&tlmm {
+	button_pins: button-state {
+		pins = "gpio24";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	emmc_pins: emmc-state {
+		clk-pins {
+			pins = "gpio9";
+			function = "sdc1_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "gpio8";
+			function = "sdc1_cmd";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "gpio4", "gpio5", "gpio6", "gpio7";
+			function = "sdc1_data";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	i2c_pins: i2c-state {
+		pins = "gpio33", "gpio34";
+		function = "blsp2_i2c0";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	spi_0_pins: spi-0-state {
+		pins = "gpio10", "gpio11", "gpio12", "gpio13";
+		function = "blsp0_spi";
+		drive-strength = <8>;
+		bias-disable;
+	};
+};
+
+/* The vendor QSEE uses 4 MiB, twice the SoC default. */
+&tz_region {
+	reg = <0x0 0x4ac00000 0x0 0x400000>;
+};
+
+&xo_board_clk {
+	clock-div = <4>;
+	clock-mult = <1>;
+};
-- 
2.47.3