Broken tulip in 2.4.5+

Broken tulip in 2.4.5+

[Tom Rini]

Hello.  The current tulip driver in 2.4.5 and up no longer works with my
'tulip' ethernet card.  0.9.14 (what's in prior to 2.4.5-pre6, iirc) works
fine with the card, as does de4x5.  Version 0.9.15-pre5 (2.4.6-pre8) and
1.1.8 (from sourceforge) both don't work.  The card is:
01:15.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
        Flags: bus master, medium devsel, latency 96, IRQ 58
        I/O ports at 0400 [size=128]
        Memory at 80080000 (32-bit, non-prefetchable) [size=128]
        Expansion ROM at <unassigned> [disabled] [size=256K]
The error(s) are as follows, for both 0.9.15-pre5 and 1.1.8:
Linux Tulip driver version 0.9.15-pre5 (June 16, 2001)
tulip0:  EEPROM default media type 10baseT.
tulip0:  Index #0 - Media 10baseT (#0) described by a 21140 non-MII (0) block.
tulip0:  Index #1 - Media 100baseTx (#3) described by a 21140 non-MII (0) block.
tulip0:  Index #2 - Media 10baseT-FDX (#4) described by a 21140 non-MII (0) block.
tulip0:  Index #3 - Media 100baseTx-FDX (#5) described by a 21140 non-MII (0) block.
tulip0:  MII transceiver #1 config 1000 status 782d advertising 05e1.
eth1: Digital DS21140 Tulip rev 34 at 0xd2118000, 00:00:94:A3:FA:0D, IRQ 58.
eth1: Using EEPROM-set media 10baseT.
eth1: Setting full-duplex based on MII#1 link partner capability of 41e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: 21140 transmit timed out, status fc680000, SIA ffffff0b ffffffff 1c09fdc0 fffffec8, resetting.
..
eth1: transmit timed out, switching to 100baseTx-FDX media.

-- 
Tom Rini (TR1265)
http://gate.crashing.org/~trini/

Re: Broken tulip in 2.4.5+

[Pasi Kärkkäinen]

On Sat, 30 Jun 2001, Tom Rini wrote:

> Hello.  The current tulip driver in 2.4.5 and up no longer works with my
> 'tulip' ethernet card.  0.9.14 (what's in prior to 2.4.5-pre6, iirc) works
> fine with the card, as does de4x5.  Version 0.9.15-pre5 (2.4.6-pre8) and
> 1.1.8 (from sourceforge) both don't work.
>

I am seeing the same problem.
I had to plug my tulip to 10Mbps HUB yesterday, and it couldn't autosense
(options=0) 10Mbps Halfduplex! It tried to use 100Mbps or something..

Also, If I try to create 100Mbps Fullduplex connection with cross-cable
between two tulip-cards (2.2.19 on the other end, and 2.4.5 on the other
end) it doesn't work either.


- Pasi Kärkkäinen

                                   ^
                                .     .
                                 Linux
                              /    -    \
                             Choice.of.the
                           .Next.Generation.