* aic-6.2.8 with U160 drives
@ 2002-05-30 13:25 J.A. Magallon
2002-05-30 16:39 ` Justin T. Gibbs
0 siblings, 1 reply; 2+ messages in thread
From: J.A. Magallon @ 2002-05-30 13:25 UTC (permalink / raw)
To: Lista Linux-Kernel; +Cc: Justin T. Gibbs
Hi.
I have noticed a problem with the recent update in 2.4.19-pre9.
I have an Adaptec 29160 card, and a couple scsi4 Fujitsu drives,
that with previous -pre version worked at 160, AFAIR.
With the recent update, they slow down to 40Mb/s. I will recheck
bios settings, but...
Info:
lspvi -v:
03:02.0 SCSI storage controller: Adaptec 7892A (rev 02)
Subsystem: Adaptec: Unknown device e2a0
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 18
BIST result: 00
I/O ports at 9000 [disabled] [size=256]
Memory at df031000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
dmesg:
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8
<Adaptec 29160 Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Vendor: FUJITSU Model: MAJ3364MP Rev: 0115
Type: Direct-Access ANSI SCSI revision: 04
Vendor: FUJITSU Model: MAJ3364MP Rev: 0115
Type: Direct-Access ANSI SCSI revision: 04
Vendor: TOSHIBA Model: CD-ROM XM-6201TA Rev: 1030
Type: CD-ROM ANSI SCSI revision: 02
Vendor: PHILIPS Model: CDD3600 CD-R/RW Rev: 2.00
Type: CD-ROM ANSI SCSI revision: 02
Vendor: IOMEGA Model: ZIP 100 Rev: E.08
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled. Depth 253
scsi0:A:1:0: Tagged Queuing enabled. Depth 253
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
Attached scsi removable disk sdc at scsi0, channel 0, id 4, lun 0
(scsi0:A:0): 40.000MB/s transfers (20.000MHz, offset 127, 16bit) <======= ?????
SCSI device sda: 71390320 512-byte hdwr sectors (36552 MB)
Partition check:
sda: sda1 sda2 sda3 sda4 < sda5 >
(scsi0:A:1): 40.000MB/s transfers (20.000MHz, offset 127, 16bit) <======= ?????
SCSI device sdb: 71390320 512-byte hdwr sectors (36552 MB)
sdb: sdb1
sdc : READ CAPACITY failed.
sdc : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sns = 70 2
ASC=3a ASCQ= 0
Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x11 0x00 0x00 0x00 0x00 0x3a
0x00 0x00 0x00 0x00 0x00 0xff 0xfe 0x01 0x00 0x00 0x00 0x00
sdc : block size assumed to be 512 bytes, disk size 1GB.
sdc: I/O error: dev 08:20, sector 0
I/O error: dev 08:20, sector 0
unable to read partition table
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 3, lun 0
(scsi0:A:2): 10.000MB/s transfers (10.000MHz, offset 16)
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.12
(scsi0:A:3): 10.000MB/s transfers (10.000MHz, offset 15)
sr1: scsi3-mmc drive: 2x/6x writer cd/rw xa/form2 cdda tray
/proc/scsi/aic7xxx/0:
Adaptec AIC7xxx driver version: 6.2.8
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Serial EEPROM:
0xc33a 0xc33a 0xc33a 0xc33a 0xc33a 0xc33a 0xc33a 0xc33a
0xc33a 0xc33a 0xc33a 0xc33a 0xc33a 0xc33a 0xc33a 0xc33a
0x08f6 0x7c59 0x2807 0x0010 0x0300 0xffff 0xffff 0xffff
0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0x0250 0xe64d
Channel A Target 0 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 255, 16bit)
Goal: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
Curr: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
Channel A Target 0 Lun 0 Settings
Commands Queued 139953
Commands Active 0
Command Openings 128
Max Tagged Openings 128
Device Queue Frozen Count 0
Channel A Target 1 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 255, 16bit)
Goal: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
Curr: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
Channel A Target 1 Lun 0 Settings
Commands Queued 25
Commands Active 0
Command Openings 253
Max Tagged Openings 253
Device Queue Frozen Count 0
Channel A Target 2 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 255, 16bit)
Goal: 10.000MB/s transfers (10.000MHz, offset 16)
Curr: 10.000MB/s transfers (10.000MHz, offset 16)
Channel A Target 2 Lun 0 Settings
Commands Queued 14
Commands Active 0
Command Openings 1
Max Tagged Openings 0
Device Queue Frozen Count 0
Channel A Target 3 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 255, 16bit)
Goal: 10.000MB/s transfers (10.000MHz, offset 15)
Curr: 10.000MB/s transfers (10.000MHz, offset 15)
Channel A Target 3 Lun 0 Settings
Commands Queued 14
Commands Active 0
Command Openings 1
Max Tagged Openings 0
Device Queue Frozen Count 0
Channel A Target 4 Negotiation Settings
User: 160.000MB/s transfers (80.000MHz DT, offset 255, 16bit)
Goal: 3.300MB/s transfers
Curr: 3.300MB/s transfers
Channel A Target 4 Lun 0 Settings
Commands Queued 6
Commands Active 0
Command Openings 1
Max Tagged Openings 0
Device Queue Frozen Count 0
Any clues ?
TIA
--
J.A. Magallon # Let the source be with you...
mailto:jamagallon@able.es
Mandrake Linux release 8.3 (Cooker) for i586
Linux werewolf 2.4.19-pre9-jam1 #1 SMP mié may 29 02:20:48 CEST 2002 i686
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: aic-6.2.8 with U160 drives
2002-05-30 13:25 aic-6.2.8 with U160 drives J.A. Magallon
@ 2002-05-30 16:39 ` Justin T. Gibbs
0 siblings, 0 replies; 2+ messages in thread
From: Justin T. Gibbs @ 2002-05-30 16:39 UTC (permalink / raw)
To: J.A. Magallon; +Cc: Lista Linux-Kernel
>I have noticed a problem with the recent update in 2.4.19-pre9.
>I have an Adaptec 29160 card, and a couple scsi4 Fujitsu drives,
>that with previous -pre version worked at 160, AFAIR.
>With the recent update, they slow down to 40Mb/s. I will recheck
>bios settings, but...
Are you sure you don't have a single ended device on the same
bus segment as the fujitsu drives? It looks like the driver is
running the bus in SE mode.
--
Justin
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2002-05-30 16:42 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2002-05-30 13:25 aic-6.2.8 with U160 drives J.A. Magallon
2002-05-30 16:39 ` Justin T. Gibbs
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®