* HPT370 + ACPI -> freeze (doesn't boot)
@ 2002-07-01 20:22 Pozsar Balazs
2002-07-01 22:16 ` Arnvid Karstad
0 siblings, 1 reply; 5+ messages in thread
From: Pozsar Balazs @ 2002-07-01 20:22 UTC (permalink / raw)
To: linux-kernel
[-- Attachment #1: Type: TEXT/PLAIN, Size: 712 bytes --]
Hi all!
I have an abit VP6 mobo with the integrated HPT370 ide-controller.
If I enable ACPI support, and I connect any harddisk to the hpt host, my
system locks up hard during boot while initializing the drive(s) on the
hpt controller (ie. before printing the 'hde:...' line). The hard drive's
led remains lit.
I attached the lspci output if that helps.
I tried the follow releases/branches, all of them locked up:
2.4.18
2.4.19-rc1
2.4.19-pre7 + ide.all.convert.10
2.4.19-pre10-ac2
2.4.19-pre8-jp13
2.4.18-wolk3.5-rc2
If I pass the 'acpi=off' option to the kernel, it does boot but obviously
I don't have acpi support that way :(.
Thanks for any help, I am willing to test any patches!
--
pozsy
[-- Attachment #2: Type: TEXT/PLAIN, Size: 10131 bytes --]
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Subsystem: ABIT Computer Corp.: Unknown device a204
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 8
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 91 06 06 00 10 a2 c4 00 00 06 00 08 00 00
10: 08 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 04 a2
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d8000000-d9ffffff
Prefetchable memory behind bridge: d0000000-d7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 98 85 07 00 30 22 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 00
20: 00 d8 f0 d9 00 d0 f0 d7 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 0c 00
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: ABIT Computer Corp.: Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 86 06 87 00 10 02 40 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 00
30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at c000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 c0 00 00 00 00 00 00 00 00 00 00 06 11 71 05
30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 00 00 00
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at c400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 c4 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 09 04 00 00
00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at c800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 c8 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 09 04 00 00
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 11
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 57 30 00 00 90 02 40 00 80 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 68 00 00 00 00 00 00 00 00 00 00 00
00:0a.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 08)
Subsystem: Creative Labs CT4832 SBLive! Value
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at cc00 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 11 02 00 05 00 90 02 08 00 01 04 00 20 80 00
10: 01 cc 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 27 80
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 02 14
00:0a.1 Input device controller: Creative Labs SB Live! (rev 08)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at d000 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 11 02 70 05 00 90 02 08 00 80 09 00 20 80 00
10: 01 d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 20 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 00 00
00:0b.0 Ethernet controller: 3Com Corporation 3c905 100BaseTX [Boomerang]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at d400 [size=64]
Expansion ROM at <unassigned> [disabled] [size=64K]
00: b7 10 50 90 07 00 00 02 00 00 00 02 00 20 00 00
10: 01 d4 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 03 08
00:0e.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366 / HPT370 (rev 03)
Subsystem: Triones Technologies, Inc.: Unknown device 0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 120 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at d800 [size=8]
Region 1: I/O ports at dc00 [size=4]
Region 2: I/O ports at e000 [size=8]
Region 3: I/O ports at e400 [size=4]
Region 4: I/O ports at e800 [size=256]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 03 11 04 00 05 00 30 02 03 00 80 01 08 78 00 00
10: 01 d8 00 00 01 dc 00 00 01 e0 00 00 01 e4 00 00
20: 01 e8 00 00 00 00 00 00 00 00 00 00 03 11 01 00
30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 08 08
01:00.0 VGA compatible controller: nVidia Corporation GeForce 256 (rev 10) (prog-if 00 [VGA])
Subsystem: LeadTek Research Inc.: Unknown device 2820
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at d8000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00: de 10 00 01 07 00 b0 02 10 00 00 03 00 20 00 00
10: 00 00 00 d8 08 00 00 d0 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7d 10 20 28
30: 00 00 00 00 60 00 00 00 00 00 00 00 05 01 05 01
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: HPT370 + ACPI -> freeze (doesn't boot)
2002-07-01 20:22 HPT370 + ACPI -> freeze (doesn't boot) Pozsar Balazs
@ 2002-07-01 22:16 ` Arnvid Karstad
2002-07-01 22:50 ` Xavier Bestel
0 siblings, 1 reply; 5+ messages in thread
From: Arnvid Karstad @ 2002-07-01 22:16 UTC (permalink / raw)
To: Pozsar Balazs; +Cc: linux-kernel
Hiya,
Pozsar Balazs writes:
> I have an abit VP6 mobo with the integrated HPT370 ide-controller.
> If I enable ACPI support, and I connect any harddisk to the hpt host, my
> system locks up hard during boot while initializing the drive(s) on the
> hpt controller (ie. before printing the 'hde:...' line). The hard drive's
> led remains lit.
I have a similar system to yours, but I have drives only on the hpt370
controller. My system boots, but crashes after 5 to 15 minuttes regardless
of usage. (I've posted this to this list on a previous occation.)
My system is running on dual P3-866 cpu's, but I don't think that this is of
any importance to the configuration. I haven't really tried to run any
patches. Do you have any similar problems when running a clean 2.4.18? Or
does your system only freeze?
> If I pass the 'acpi=off' option to the kernel, it does boot but obviously
> I don't have acpi support that way :(.
I haven't tried this. But my system is not exactly freezing, just I cant
access the drives anymore.
> Thanks for any help, I am willing to test any patches!
If u find anything that works, could you send me a note aswell? Since I've
been wanting to run Linux on my machine for a while now and my systems seems
to preform better when the drives are connected to the HPT370 than the other
internal VIA ide controller. Atleast this is the 'general' feeling I have
after experimenting with a few things under windows 2000 pro.
Best regards,
Arnvid Karstad
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: HPT370 + ACPI -> freeze (doesn't boot)
2002-07-01 22:16 ` Arnvid Karstad
@ 2002-07-01 22:50 ` Xavier Bestel
2002-07-02 4:50 ` Ulrich Wiederhold
0 siblings, 1 reply; 5+ messages in thread
From: Xavier Bestel @ 2002-07-01 22:50 UTC (permalink / raw)
To: Arnvid Karstad; +Cc: Pozsar Balazs, Linux Kernel Mailing List
Le mar 02/07/2002 à 00:16, Arnvid Karstad a écrit :
> Hiya,
>
> Pozsar Balazs writes:
> > I have an abit VP6 mobo with the integrated HPT370 ide-controller.
> > If I enable ACPI support, and I connect any harddisk to the hpt host, my
> > system locks up hard during boot while initializing the drive(s) on the
> > hpt controller (ie. before printing the 'hde:...' line). The hard drive's
> > led remains lit.
>
> I have a similar system to yours, but I have drives only on the hpt370
> controller. My system boots, but crashes after 5 to 15 minuttes regardless
> of usage. (I've posted this to this list on a previous occation.)
Mine (ABit VP6, some drives on both controllers) either stops at
"hde:..." at boot or freezes a bit later when ACPI is on with stable
kernels (or -ac ones). Without ACPI it runs pretty well, unless I use
USBnet.
Xav
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: HPT370 + ACPI -> freeze (doesn't boot)
2002-07-01 22:50 ` Xavier Bestel
@ 2002-07-02 4:50 ` Ulrich Wiederhold
0 siblings, 0 replies; 5+ messages in thread
From: Ulrich Wiederhold @ 2002-07-02 4:50 UTC (permalink / raw)
To: Linux Kernel Mailing List
Hi,
my kernel (still 2.4.17-rc2) boots from hde and finds hde and hdg during
bootup.
After the boot-prozess is finished, I can't access the drives anymore.
(I have only /boot on hde1, the rest on scsi-disks).
I will try 2.4.19 if it's finish.
If you find a solution, pls msg me as well, thanks.
Uli
--
'The box said, 'Requires Windows 95 or better', so i installed Linux - TKK 5
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: HPT370 + ACPI -> freeze (doesn't boot)
[not found] <20020703192645.B836@brodo.de>
@ 2002-07-03 18:56 ` Pozsar Balazs
0 siblings, 0 replies; 5+ messages in thread
From: Pozsar Balazs @ 2002-07-03 18:56 UTC (permalink / raw)
To: Dominik Brodowski; +Cc: linux-kernel
Hi,
I tried
2.4.18 + acpi-20020611
and
2.4.18 + acpi-20020611 + pciirq-27
but both of them freeze the same way :(.
I noticed that it is not an immediate freeze though. alt-sysrq-T works for
about 5 seconds... after that, nothing.
If you do think the call traces would do help, I might take time to do
write them down.
On Wed, 3 Jul 2002, Dominik Brodowski wrote:
> Hi,
>
> On Tue, Jul 02, 2002 at 08:33:32AM +0200, Pozsar Balazs wrote:
> >
> > I tried 2.4.18-pre8 + acpi-20020503 + pciirq-18 and the same freeze :(
> pciirq-18 is buggy, unfortunately. Could you please get the latest
> acpi-patch from
> http://www.sourceforge.net/projects/acpi/ ?
> Thanks.
>
> Dominik
>
--
pozsy
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2002-07-03 18:53 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2002-07-01 20:22 HPT370 + ACPI -> freeze (doesn't boot) Pozsar Balazs
2002-07-01 22:16 ` Arnvid Karstad
2002-07-01 22:50 ` Xavier Bestel
2002-07-02 4:50 ` Ulrich Wiederhold
[not found] <20020703192645.B836@brodo.de>
2002-07-03 18:56 ` Pozsar Balazs
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®