* Re: PROBLEM: floppy oops in 2.5.25
@ 2002-07-07 10:57 Mikael Pettersson
0 siblings, 0 replies; 2+ messages in thread
From: Mikael Pettersson @ 2002-07-07 10:57 UTC (permalink / raw)
To: fbujanic; +Cc: linux-kernel
On Sat, 6 Jul 2002 22:27:23 -0400 (EDT), Filip J. Bujanic wrote:
>[1.] One line summary of the problem:
> accessing floppy drive oopses 2.5.25 kernel
If you had searched the LKML archives you would soon have found out
that the floppy driver is known to be broken since 2.5.13.
A partial fix exists which eliminates the oopses and allows raw
/dev/fd0 accesses to work; VFS accesses to mounted floppies are
still broken however. You can get it from the -dj patch or from
http://www.csd.uu.se/~mikpe/linux/patches/2.5/patch-fix-floppy-2.5.25
/Mikael
^ permalink raw reply [flat|nested] 2+ messages in thread
* PROBLEM: floppy oops in 2.5.25
@ 2002-07-07 2:27 Filip J. Bujanic
0 siblings, 0 replies; 2+ messages in thread
From: Filip J. Bujanic @ 2002-07-07 2:27 UTC (permalink / raw)
To: linux-kernel
[1.] One line summary of the problem:
accessing floppy drive oopses 2.5.25 kernel
[2.] Full description of the problem/report:
formating or dd-ing a floppy raises an oops in 2.5.25 kernel
[3.] Keywords (i.e., modules, networking, kernel):
floppy, 2.5.25
[4.] Kernel version (from /proc/version):
Linux version 2.5.25 (root@lizard.fikus.com) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-85)) #7 SMP Sat Jul 6 11:26:56 EDT 2002
[5.] Output of Oops.. message (if applicable) with symbolic information
resolved (see Documentation/oops-tracing.txt)
ksymoops 2.4.5 on i686 2.5.25. Options used
-v /boot/vmlinux-2.5.25 (specified)
-k /proc/ksyms (default)
-l /proc/modules (default)
-o /lib/modules/2.5.25/ (default)
-m /boot/System.map-2.5.25 (specified)
Unable to handle kernel NULL pointer dereference at virtual address 000000a8
c0218b87
*pde = 00000000
Oops: 0000
CPU: 0
EIP: 0010:[<c0218b87>] Not tainted
Using defaults from ksymoops -t elf32-i386 -a i386
EFLAGS: 00010086
eax: 00000000 ebx: 00000000 ecx: c897be40 edx: c897be00
esi: c897be40 edi: c112b504 ebp: d7d0f0e4 esp: c897bdf8
ds: 0018 es: 0018 ss: 0018
Stack: c897be10 c897be40 c02223f7 00000000 00000000 c897be40 00000001 00000001
dead4ead c897be1c c897be1c 00000000 c032dd96 00000000 c112b504 00000400
00000000 00000000 00000000 00000000 d7d0f0e4 00000000 00000000 00000001
Call Trace: [<c02223f7>] [<c014b535>] [<c0222320>] [<c022245d>] [<c014bb39>]
[<c02221b7>] [<c014bcf6>] [<c015b2cb>] [<c014b473>] [<c014bf85>] [<c0143ae6>]
[<c01439ed>] [<c0143e15>] [<c010742b>]
Code: 8b b3 a8 00 00 00 81 7e 04 ad 4e ad de 74 1a 68 80 8b 21 c0
>>EIP; c0218b87 <generic_unplug_device+7/120> <=====
>>ecx; c897be40 <_end+8517804/1a5ed9c4>
>>edx; c897be00 <_end+85177c4/1a5ed9c4>
>>esi; c897be40 <_end+8517804/1a5ed9c4>
>>edi; c112b504 <_end+cc6ec8/1a5ed9c4>
>>ebp; d7d0f0e4 <_end+178aaaa8/1a5ed9c4>
>>esp; c897bdf8 <_end+85177bc/1a5ed9c4>
Trace; c02223f7 <__floppy_read_block_0+c7/f0>
Trace; c014b535 <bdput+15/e0>
Trace; c0222320 <floppy_rb0_complete+0/10>
Trace; c022245d <floppy_read_block_0+3d/50>
Trace; c014bb39 <check_disk_change+79/90>
Trace; c02221b7 <floppy_open+347/3b0>
Trace; c014bcf6 <do_open+156/350>
Trace; c015b2cb <new_inode+b/c0>
Trace; c014b473 <bdget+163/210>
Trace; c014bf85 <blkdev_open+25/30>
Trace; c0143ae6 <dentry_open+e6/1b0>
Trace; c01439ed <filp_open+4d/60>
Trace; c0143e15 <sys_open+35/70>
Trace; c010742b <syscall_call+7/b>
Code; c0218b87 <generic_unplug_device+7/120>
00000000 <_EIP>:
Code; c0218b87 <generic_unplug_device+7/120> <=====
0: 8b b3 a8 00 00 00 mov 0xa8(%ebx),%esi <=====
Code; c0218b8d <generic_unplug_device+d/120>
6: 81 7e 04 ad 4e ad de cmpl $0xdead4ead,0x4(%esi)
Code; c0218b94 <generic_unplug_device+14/120>
d: 74 1a je 29 <_EIP+0x29> c0218bb0 <generic_unplug_device+30/120>
Code; c0218b96 <generic_unplug_device+16/120>
f: 68 80 8b 21 c0 push $0xc0218b80
[6.] A small shell script or example program which triggers the
problem (if possible)
mformat a:
or
dd if=out.txt of=/dev/fd0
[7.] Environment
[7.1.] Software (add the output of the ver_linux script here)
Linux lizard.fikus.com 2.5.25 #7 SMP Sat Jul 6 11:26:56 EDT 2002 i686
unknown
Gnu C 2.96
Gnu make 3.79.1
binutils 2.10.91.0.2
util-linux 2.11f
mount 2.11b
modutils 2.4.13
e2fsprogs 1.26
reiserfsprogs 3.x.0f
pcmcia-cs 3.1.22
PPP 2.4.0
isdn4k-utils 3.1pre1
Linux C Library 2.2.4
Dynamic linker (ldd) 2.2.4
Procps 2.0.7
Net-tools 1.57
Console-tools 0.3.3
Sh-utils 2.0
Modules Loaded parport_pc lp parport
[7.2.] Processor information (from /proc/cpuinfo):
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 5
model name : 00/05
stepping : 2
cpu MHz : 451.059
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
cmov pat pse36 mmx fxsr
bogomips : 888.83
processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 5
model name : 00/05
stepping : 2
cpu MHz : 451.059
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
cmov pat pse36 mmx fxsr
bogomips : 901.12
[7.3.] Module information (from /proc/modules):
parport_pc 23656 1 (autoclean)
lp 7136 0 (autoclean)
parport 30208 1 (autoclean) [parport_pc lp]
[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0213-0213 : isapnp read
0290-0297 : PnPBIOS PNP0c02
02f8-02ff : serial(auto)
0376-0376 : ide1
0378-037a : parport0
037b-037f : parport0
03c0-03df : vga+
03c0-03df : matrox
03f2-03f5 : floppy
03f6-03f6 : ide0
03f7-03f7 : floppy DIR
03f8-03ff : serial(auto)
0400-043f : PnPBIOS PNP0c02
0440-044f : PnPBIOS PNP0c02
04d0-04d1 : PnPBIOS PNP0c02
0a79-0a79 : isapnp write
0cf8-0cff : PCI conf1
d000-dfff : PCI Bus #01
e400-e4ff : Lite-On Communications Inc LNE100TX
e400-e4ff : tulip
e800-e8ff : Adaptec AIC-7881U
e800-e8ff : aic7xxx
ef80-ef9f : Intel Corp. 82371AB PIIX4 USB
ffa0-ffaf : Intel Corp. 82371AB PIIX4 IDE
ffa0-ffa7 : ide0
ffa8-ffaf : ide1
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000c8000-000cdfff : Extension ROM
000f0000-000fffff : System ROM
00100000-17feffff : System RAM
00100000-002ef893 : Kernel code
002ef894-0039fdf3 : Kernel data
17ff0000-17ff7fff : ACPI Tables
17ff8000-17ffffff : ACPI Non-volatile Storage
f1800000-f58fffff : PCI Bus #01
f2000000-f3ffffff : Matrox Graphics, Inc. MGA G400 AGP
f2000000-f3ffffff : matroxfb FB
f8000000-fbffffff : Intel Corp. 440BX/ZX - 82443BX/ZX Host bridge
fda00000-feafffff : PCI Bus #01
fe000000-fe7fffff : Matrox Graphics, Inc. MGA G400 AGP
feafc000-feafffff : Matrox Graphics, Inc. MGA G400 AGP
feafc000-feafffff : matroxfb MMIO
febfef00-febfefff : Lite-On Communications Inc LNE100TX
febfef00-febfefff : tulip
febff000-febfffff : Adaptec AIC-7881U
febff000-febfffff : aic7xxx
fec00000-fec00fff : reserved
fee00000-fee00fff : reserved
fffc0000-ffffffff : reserved
[7.5.] PCI information ('lspci -vvv' as root)
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge
(rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=x1
00:01.0 PCI bridge: Intel Corporation 440BX/ZX - 82443BX/ZX AGP bridge
(rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fda00000-feafffff
Prefetchable memory behind bridge: f1800000-f58fffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00:07.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at ffa0 [size=16]
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at ef80 [size=32]
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:12.0 SCSI storage controller: Adaptec AIC-7881U (rev 01)
Subsystem: Adaptec AHA-2940UW SCSI Host Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at e800 [disabled] [size=256]
Region 1: Memory at febff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at febe0000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:13.0 Ethernet controller: Lite-On Communications Inc LNE100TX (rev 21)
Subsystem: Netgear FA310TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at e400 [size=256]
Region 1: Memory at febfef00 (32-bit, non-prefetchable) [size=256]
Expansion ROM at feb80000 [disabled] [size=256K]
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev
04) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G400 MAX/Dual Head
32Mb
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f2000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at feafc000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at fe000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at feae0000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
[7.6.] SCSI information (from /proc/scsi/scsi)
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: WDIGTL Model: WDE9100AV Rev: 1.50
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: WDIGTL Model: WD183 ULTRA2 Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 02 Lun: 00
Vendor: SEAGATE Model: ST19171N Rev: F224
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 03 Lun: 00
Vendor: SEAGATE Model: ST39173N Rev: 5698
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: HP Model: T20 Rev: 3.01
Type: Sequential-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 05 Lun: 00
Vendor: RICOH Model: MP6200S Rev: 2.20
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 06 Lun: 00
Vendor: SEAGATE Model: ST336737LW Rev: 0105
Type: Direct-Access ANSI SCSI revision: 03
[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you
think to be relevant):
[X.] Other notes, patches, fixes, workarounds:
This is a dual PII tyan motherboard worked flawlessly under all
kernels up to 2.4.19. Since than I have many problems especialy if I
attempt to use ACPI, oppses during floppy access, md raid0 failiures under
heavy load and random ADAPTEC lockups....
thanks
fil
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2002-07-07 10:55 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2002-07-07 10:57 PROBLEM: floppy oops in 2.5.25 Mikael Pettersson
-- strict thread matches above, loose matches on Subject: below --
2002-07-07 2:27 Filip J. Bujanic
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®