* Problem with PCMCIA 8139too
@ 2002-08-15 19:55 gigerstyle
2002-08-19 9:13 ` gigerstyle
0 siblings, 1 reply; 3+ messages in thread
From: gigerstyle @ 2002-08-15 19:55 UTC (permalink / raw)
To: linux-kernel
Hi!
I have successfully installed the PCMCIA CardBus NIC with realtek 8139 chip. I'm using the yenta_socket module and of course the 8139too module.
As test I set up the interface with
ifconfig eth0 192.168.0.5 up
and made a ping to another host.
Seems all to be ok.. no problems there.
When I put my Notebook in sleeping mode and resume it, ifconfig shows still the same network configuration, BUT now I can't ping any other hosts.
A
ifconfig eth0 down
and
ifconfig eth0 192.168.0.5 up
doesn't help.
Ping says only:
PING 192.168.0.1 (192.168.0.1) from 192.168.0.5 : 56(84) bytes of data.
>From 192.168.0.5: icmp_seq=1 Destination Host Unreachable
>From 192.168.0.5 icmp_seq=1 Destination Host Unreachable
>From 192.168.0.5 icmp_seq=2 Destination Host Unreachable
>From 192.168.0.5 icmp_seq=3 Destination Host Unreachable
>From 192.168.0.5 icmp_seq=4 Destination Host Unreachable
>From 192.168.0.5 icmp_seq=5 Destination Host Unreachable
>From 192.168.0.5 icmp_seq=6 Destination Host Unreachable
--- 192.168.0.1 ping statistics ---
10 packets transmitted, 0 received, +7 errors, 100% loss, time 9025ms
Have also tried many other things like reloading modules,
shutting down pcmcia before sleeping etc etc....
As last I used the hotplugging scripts...but also without success.
There are no errors in message or something else:-(
After a standby I have to reboot the Notebook for a proper working NIC:-(
Is there any way that it will work? I like standby and hate booting;-)
Other cards have no problems (older realtek, aironet 340) but they aren't cardbus.
/varr/log/messages:
Aug 15 21:18:59 vaio kernel: cs: cb_alloc(bus 6): vendor 0x10ec, device 0x8139
Aug 15 21:18:59 vaio kernel: PCI: Enabling device 06:00.0 (0000 -> 0003)
Aug 15 21:19:00 vaio cardmgr[533]: socket 1: CardBus hotplug device
Aug 15 21:19:00 vaio kernel: 8139too Fast Ethernet driver 0.9.25
Aug 15 21:19:00 vaio kernel: PCI: Setting latency timer of device 06:00.0 to 64
Aug 15 21:19:00 vaio kernel: eth0: RealTek RTL8139 Fast Ethernet at 0xccb99000, 00:30:4f:1d:53:7a, IRQ 9
Aug 15 21:19:00 vaio kernel: eth0: Identified 8139 chip type 'RTL-8139C'
Aug 15 21:19:00 vaio insmod: Using /lib/modules/2.4.19/kernel/drivers/net/mii.o
Aug 15 21:19:00 vaio insmod: Symbol version prefix ''
Aug 15 21:19:00 vaio insmod: Using /lib/modules/2.4.19/kernel/drivers/net/8139too.o
Aug 15 21:19:19 vaio kernel: eth0: Setting 100mbps half-duplex based on auto-negotiated partner ability 40a1.
Loaded modules:
Module Size Used by Not tainted
8139too 14272 1
mii 1056 0 [8139too]
soundcore 3268 0 (autoclean)
ipv6 124928 -1 (autoclean)
ds 6368 2
yenta_socket 8704 2
pcmcia_core 34240 0 [ds yenta_socket]
isa-pnp 27388 0 (unused)
joydev 6816 0 (unused)
evdev 4096 0 (unused)
mousedev 3808 1
hid 18944 0 (unused)
usbmouse 1792 0 (unused)
input 3072 0 [joydev evdev mousedev hid usbmouse]
uhci 23816 0 (unused)
usbcore 54272 1 [hid usbmouse uhci]
nls_iso8859-1 2848 1 (autoclean)
nls_cp437 4384 1 (autoclean)
Ah before I forget: I'm using Kernel Version 2.4.19
More info needed? No problem..
Marc Giger
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: Problem with PCMCIA 8139too
2002-08-15 19:55 Problem with PCMCIA 8139too gigerstyle
@ 2002-08-19 9:13 ` gigerstyle
2002-08-20 11:07 ` Marc Giger
0 siblings, 1 reply; 3+ messages in thread
From: gigerstyle @ 2002-08-19 9:13 UTC (permalink / raw)
To: linux-kernel
Hi again...
The problem still exists...
I also tried the newest kernel (2.4.20-pre3).
I think the 8139 driver is correct. The apm driver has a problem.
Explanation:
When I boot my Notebook without loaded the network and pcmcia driver then set it into sleeping mode and resume it later, then load all needed drivers, the card is recognised but does not work. Same problem.
Is it a problem with apm and pci-bus? (All other direct connected devices (Soundcard, graphiccard etc) working well).
Thank you
Marc Giger
On Thu, 15 Aug 2002 21:55:23 +0200
gigerstyle@gmx.ch wrote:
> Hi!
>
> I have successfully installed the PCMCIA CardBus NIC with realtek 8139 chip. I'm using the yenta_socket module and of course the 8139too module.
>
> As test I set up the interface with
>
> ifconfig eth0 192.168.0.5 up
>
> and made a ping to another host.
>
> Seems all to be ok.. no problems there.
>
>
> When I put my Notebook in sleeping mode and resume it, ifconfig shows still the same network configuration, BUT now I can't ping any other hosts.
>
> A
> ifconfig eth0 down
> and
> ifconfig eth0 192.168.0.5 up
>
> doesn't help.
>
> Ping says only:
>
> PING 192.168.0.1 (192.168.0.1) from 192.168.0.5 : 56(84) bytes of data.
> From 192.168.0.5: icmp_seq=1 Destination Host Unreachable
> From 192.168.0.5 icmp_seq=1 Destination Host Unreachable
> From 192.168.0.5 icmp_seq=2 Destination Host Unreachable
> From 192.168.0.5 icmp_seq=3 Destination Host Unreachable
> From 192.168.0.5 icmp_seq=4 Destination Host Unreachable
> From 192.168.0.5 icmp_seq=5 Destination Host Unreachable
> From 192.168.0.5 icmp_seq=6 Destination Host Unreachable
>
> --- 192.168.0.1 ping statistics ---
> 10 packets transmitted, 0 received, +7 errors, 100% loss, time 9025ms
>
>
> Have also tried many other things like reloading modules,
> shutting down pcmcia before sleeping etc etc....
> As last I used the hotplugging scripts...but also without success.
>
> There are no errors in message or something else:-(
> After a standby I have to reboot the Notebook for a proper working NIC:-(
>
> Is there any way that it will work? I like standby and hate booting;-)
>
> Other cards have no problems (older realtek, aironet 340) but they aren't cardbus.
>
>
> /varr/log/messages:
>
> Aug 15 21:18:59 vaio kernel: cs: cb_alloc(bus 6): vendor 0x10ec, device 0x8139
> Aug 15 21:18:59 vaio kernel: PCI: Enabling device 06:00.0 (0000 -> 0003)
> Aug 15 21:19:00 vaio cardmgr[533]: socket 1: CardBus hotplug device
> Aug 15 21:19:00 vaio kernel: 8139too Fast Ethernet driver 0.9.25
> Aug 15 21:19:00 vaio kernel: PCI: Setting latency timer of device 06:00.0 to 64
> Aug 15 21:19:00 vaio kernel: eth0: RealTek RTL8139 Fast Ethernet at 0xccb99000, 00:30:4f:1d:53:7a, IRQ 9
> Aug 15 21:19:00 vaio kernel: eth0: Identified 8139 chip type 'RTL-8139C'
> Aug 15 21:19:00 vaio insmod: Using /lib/modules/2.4.19/kernel/drivers/net/mii.o
> Aug 15 21:19:00 vaio insmod: Symbol version prefix ''
> Aug 15 21:19:00 vaio insmod: Using /lib/modules/2.4.19/kernel/drivers/net/8139too.o
> Aug 15 21:19:19 vaio kernel: eth0: Setting 100mbps half-duplex based on auto-negotiated partner ability 40a1.
>
> Loaded modules:
>
> Module Size Used by Not tainted
> 8139too 14272 1
> mii 1056 0 [8139too]
> soundcore 3268 0 (autoclean)
> ipv6 124928 -1 (autoclean)
> ds 6368 2
> yenta_socket 8704 2
> pcmcia_core 34240 0 [ds yenta_socket]
> isa-pnp 27388 0 (unused)
> joydev 6816 0 (unused)
> evdev 4096 0 (unused)
> mousedev 3808 1
> hid 18944 0 (unused)
> usbmouse 1792 0 (unused)
> input 3072 0 [joydev evdev mousedev hid usbmouse]
> uhci 23816 0 (unused)
> usbcore 54272 1 [hid usbmouse uhci]
> nls_iso8859-1 2848 1 (autoclean)
> nls_cp437 4384 1 (autoclean)
>
>
> Ah before I forget: I'm using Kernel Version 2.4.19
>
> More info needed? No problem..
>
>
> Marc Giger
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: Problem with PCMCIA 8139too
2002-08-19 9:13 ` gigerstyle
@ 2002-08-20 11:07 ` Marc Giger
0 siblings, 0 replies; 3+ messages in thread
From: Marc Giger @ 2002-08-20 11:07 UTC (permalink / raw)
To: linux-kernel
sorry for again disturbing.......
after a suspend to disk (very slow:-( ) the card works.
but afer a suspend to ram still not..:-(
marc
On Mon, 19 Aug 2002 11:13:35 +0200
gigerstyle@gmx.ch wrote:
> Hi again...
>
> The problem still exists...
> I also tried the newest kernel (2.4.20-pre3).
>
> I think the 8139 driver is correct. The apm driver has a problem.
>
> Explanation:
>
> When I boot my Notebook without loaded the network and pcmcia driver then set it into sleeping mode and resume it later, then load all needed drivers, the card is recognised but does not work. Same problem.
>
> Is it a problem with apm and pci-bus? (All other direct connected devices (Soundcard, graphiccard etc) working well).
>
> Thank you
>
> Marc Giger
>
>
> On Thu, 15 Aug 2002 21:55:23 +0200
> gigerstyle@gmx.ch wrote:
>
> > Hi!
> >
> > I have successfully installed the PCMCIA CardBus NIC with realtek 8139 chip. I'm using the yenta_socket module and of course the 8139too module.
> >
> > As test I set up the interface with
> >
> > ifconfig eth0 192.168.0.5 up
> >
> > and made a ping to another host.
> >
> > Seems all to be ok.. no problems there.
> >
> >
> > When I put my Notebook in sleeping mode and resume it, ifconfig shows still the same network configuration, BUT now I can't ping any other hosts.
> >
> > A
> > ifconfig eth0 down
> > and
> > ifconfig eth0 192.168.0.5 up
> >
> > doesn't help.
> >
> > Ping says only:
> >
> > PING 192.168.0.1 (192.168.0.1) from 192.168.0.5 : 56(84) bytes of data.
> > From 192.168.0.5: icmp_seq=1 Destination Host Unreachable
> > From 192.168.0.5 icmp_seq=1 Destination Host Unreachable
> > From 192.168.0.5 icmp_seq=2 Destination Host Unreachable
> > From 192.168.0.5 icmp_seq=3 Destination Host Unreachable
> > From 192.168.0.5 icmp_seq=4 Destination Host Unreachable
> > From 192.168.0.5 icmp_seq=5 Destination Host Unreachable
> > From 192.168.0.5 icmp_seq=6 Destination Host Unreachable
> >
> > --- 192.168.0.1 ping statistics ---
> > 10 packets transmitted, 0 received, +7 errors, 100% loss, time 9025ms
> >
> >
> > Have also tried many other things like reloading modules,
> > shutting down pcmcia before sleeping etc etc....
> > As last I used the hotplugging scripts...but also without success.
> >
> > There are no errors in message or something else:-(
> > After a standby I have to reboot the Notebook for a proper working NIC:-(
> >
> > Is there any way that it will work? I like standby and hate booting;-)
> >
> > Other cards have no problems (older realtek, aironet 340) but they aren't cardbus.
> >
> >
> > /varr/log/messages:
> >
> > Aug 15 21:18:59 vaio kernel: cs: cb_alloc(bus 6): vendor 0x10ec, device 0x8139
> > Aug 15 21:18:59 vaio kernel: PCI: Enabling device 06:00.0 (0000 -> 0003)
> > Aug 15 21:19:00 vaio cardmgr[533]: socket 1: CardBus hotplug device
> > Aug 15 21:19:00 vaio kernel: 8139too Fast Ethernet driver 0.9.25
> > Aug 15 21:19:00 vaio kernel: PCI: Setting latency timer of device 06:00.0 to 64
> > Aug 15 21:19:00 vaio kernel: eth0: RealTek RTL8139 Fast Ethernet at 0xccb99000, 00:30:4f:1d:53:7a, IRQ 9
> > Aug 15 21:19:00 vaio kernel: eth0: Identified 8139 chip type 'RTL-8139C'
> > Aug 15 21:19:00 vaio insmod: Using /lib/modules/2.4.19/kernel/drivers/net/mii.o
> > Aug 15 21:19:00 vaio insmod: Symbol version prefix ''
> > Aug 15 21:19:00 vaio insmod: Using /lib/modules/2.4.19/kernel/drivers/net/8139too.o
> > Aug 15 21:19:19 vaio kernel: eth0: Setting 100mbps half-duplex based on auto-negotiated partner ability 40a1.
> >
> > Loaded modules:
> >
> > Module Size Used by Not tainted
> > 8139too 14272 1
> > mii 1056 0 [8139too]
> > soundcore 3268 0 (autoclean)
> > ipv6 124928 -1 (autoclean)
> > ds 6368 2
> > yenta_socket 8704 2
> > pcmcia_core 34240 0 [ds yenta_socket]
> > isa-pnp 27388 0 (unused)
> > joydev 6816 0 (unused)
> > evdev 4096 0 (unused)
> > mousedev 3808 1
> > hid 18944 0 (unused)
> > usbmouse 1792 0 (unused)
> > input 3072 0 [joydev evdev mousedev hid usbmouse]
> > uhci 23816 0 (unused)
> > usbcore 54272 1 [hid usbmouse uhci]
> > nls_iso8859-1 2848 1 (autoclean)
> > nls_cp437 4384 1 (autoclean)
> >
> >
> > Ah before I forget: I'm using Kernel Version 2.4.19
> >
> > More info needed? No problem..
> >
> >
> > Marc Giger
> >
> > -
> > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
> > Please read the FAQ at http://www.tux.org/lkml/
> >
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2002-08-20 11:01 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2002-08-15 19:55 Problem with PCMCIA 8139too gigerstyle
2002-08-19 9:13 ` gigerstyle
2002-08-20 11:07 ` Marc Giger
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®