* bttv and DVB cards hardware incompaibility only in late linux
@ 2002-10-14 23:54 Javier Marcet
2002-10-15 0:07 ` Javier Marcet
0 siblings, 1 reply; 2+ messages in thread
From: Javier Marcet @ 2002-10-14 23:54 UTC (permalink / raw)
To: linux-kernel; +Cc: Gerd Knorr, vdr, linux-dvb
[-- Attachment #1: Type: text/plain, Size: 2328 bytes --]
Hi,
a few weeks ago I reported a problem I was having with a bttv TV card.
I also sent a cc to Gerd Knorr, bttv's author. However I got no response
at all, but from one guy who said everything worked on his system.
I have been trying to find where was the actual problem. What I found is
quite odd.
First let me say that besides the kernel you'll see in the logs I've
tried with a few different version, up to some 2.4.18, and of course
with nearly everything disabled, like APIC, ACPI or PnP. The results
were the same.
Briefly: on this PC I use a Hauppauge DVB card - a Siemens clone,
revision 1.3 -, an Adaptec 2940U2W, a SBLive! and a 3C905C network card.
All that works like a charm.
I also used to have a bttv card there, but I got many problems trying to
use it on that crowded PCI. I know that a few months ago it had worked,
and it also did on Windows (does now? I don't have a copy installed
anymore) on Windows.
I get lot's a IRQ sync errors in the syslog, and can't get any image from
the bttv card.
What I first tried is of course using the bttv without loading the DVB
drivers, since they could clash. This didn't work. I began moving the
cards on the PCI slots, removing some and trying again. Until I found
one combination which did work.
Without the DVB card _plugged_, I can use the bttv with no problems,
having everything else installed and being used. Yet, the moment I plug
in again the DVB board, the bttv does not work anymore.
This would make more sense if the clash was only between the drivers,
specially taking into account that both boards are from Hauppauge and
both worked at the same time on the system under a different OS.
There is one more oddity I noticed seeing the logs I attach, and it's
that with the DVB card out, the bttv board is recognized as a 'WinTV GO'
by lspci, but with the DVB in it is _unrecognized_.
This last thing just killed me. If anyone can point me to what I might
do to try to solve this thing, I'll appreciate it. I am confident it is
not a hardware incompatibility for the reasons I gave above. Also, even
if I did have to unload one's drivers to use the other's, there must be
some way to have both co-habiting on the same PCI bus.
--
Javier Marcet <jmarcet@pobox.com>
Saint Louis University, Madrid Campus
[-- Attachment #2: Type: application/pgp-signature, Size: 197 bytes --]
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: bttv and DVB cards hardware incompaibility only in late linux
2002-10-14 23:54 bttv and DVB cards hardware incompaibility only in late linux Javier Marcet
@ 2002-10-15 0:07 ` Javier Marcet
0 siblings, 0 replies; 2+ messages in thread
From: Javier Marcet @ 2002-10-15 0:07 UTC (permalink / raw)
To: linux-kernel; +Cc: Gerd Knorr, vdr, linux-dvb
[-- Attachment #1.1: Type: text/plain, Size: 148 bytes --]
Sorry for the attachments on the previous e-mail, the go now :)
--
Javier Marcet <jmarcet@pobox.com>
Saint Louis University, Madrid Campus
[-- Attachment #1.2: dmesg output without the dvb card plugged --]
[-- Type: text/plain, Size: 10352 bytes --]
Linux version 2.4.20-pre8-ac3-marcet (root@jerry.marcet.dyndns.org) (gcc version 3.2) #1 Tue Oct 15 00:12:27 CEST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000017fec000 (usable)
BIOS-e820: 0000000017fec000 - 0000000017fef000 (ACPI data)
BIOS-e820: 0000000017fef000 - 0000000017fff000 (reserved)
BIOS-e820: 0000000017fff000 - 0000000018000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
383MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 98284
zone(0): 4096 pages.
zone(1): 94188 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 ASUS ) @ 0x000f6a70
ACPI: RSDT (v001 ASUS A7V-133 12336.12337) @ 0x17fec000
ACPI: FADT (v001 ASUS A7V-133 12336.12337) @ 0x17fec080
ACPI: BOOT (v001 ASUS A7V-133 12336.12337) @ 0x17fec040
ACPI: DSDT (v001 ASUS A7V-133 00000.04096) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: MADT not present
Kernel command line: root=/dev/sda2 video=matrox:mem:32,xres:1280,yres:960,left:264,right:24,hslen:160,upper:47,lower:1,vslen:3,pixclock:6024,sync:0x03,depth:32,pan panicblink=2
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 1544.796 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3039.23 BogoMIPS
Memory: 383020k/393136k available (1663k kernel code, 7552k reserved, 326k data, 276k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
ramfs: mounted with options: <defaults>
ramfs: max_pages=48149 max_file_pages=0 max_inodes=0 max_dentries=48149
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0383fbff c1c3fbff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbff c1c3fbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
CPU: AMD Athlon(TM) XP 1800+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
HZ: Currently used HZ value is (1000)
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1544.0161 MHz.
..... host bus clock speed is 268.0549 MHz.
cpu: 0, clocks: 268549, slice: 134274
CPU0<T0:268544,T1:134256,D:14,S:134274,C:268549>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20021002
PCI: PCI BIOS revision 2.10 entry at 0xf1180, last bus=1
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S3 S4 S5)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Scanning bus 00
Found 00:00 [1106/0305] 000600 00
Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 89 & 1f -> 09
Found 00:08 [1106/8305] 000604 01
Found 00:20 [1106/0686] 000601 00
Found 00:21 [1106/0571] 000101 00
Found 00:22 [1106/3038] 000c03 00
Found 00:23 [1106/3038] 000c03 00
Found 00:24 [1106/3057] 000680 00
Found 00:48 [1102/0002] 000401 00
Found 00:49 [1102/7002] 000980 00
Found 00:50 [109e/036e] 000400 00
Found 00:51 [109e/0878] 000480 00
Found 00:58 [9005/0010] 000100 00
Found 00:68 [10b7/9200] 000200 00
Found 00:88 [105a/0d30] 000180 00
Fixups for bus 00
Scanning behind PCI bridge 00:01.0, config 010100, pass 0
Scanning bus 01
Found 01:00 [102b/0525] 000300 00
Fixups for bus 01
Bus scan for 01 returning with max=01
Scanning behind PCI bridge 00:01.0, config 010100, pass 1
Bus scan for 00 returning with max=01
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
PCI: Probing PCI hardware
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
PnPBIOS: Found PnP BIOS installation structure at 0xc00fc4f0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc520, dseg 0xf0000
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
PnPBIOS: PNP0c02: ioport range 0xe400-0xe47f has been reserved
PnPBIOS: PNP0c02: ioport range 0xe800-0xe83f could not be reserved
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
SBF: Simple Boot Flag extension found and enabled.
SBF: Setting boot flags 0x1
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1 C2, 16 throttling states)
matroxfb: Matrox Millennium G400 MAX (AGP) detected
matroxfb: MTRR's turned on
matroxfb: 1280x960x32bpp (virtual: 1280x3276)
matroxfb: framebuffer at 0xE2000000, mapped to 0xd880f000, size 33554432
Console: switching to colour frame buffer device 160x60
fb0: MATROX VGA frame buffer device
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:04.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:04.1
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
PDC20265: IDE controller at PCI slot 00:11.0
PDC20265: chipset revision 2
PDC20265: not 100% native mode: will probe irqs later
PDC20265: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode.
PDC20265: FORCING BURST BIT 0x00->0x01 ACTIVE
ide2: BM-DMA at 0x7800-0x7807, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0x7808-0x780f, BIOS settings: hdg:DMA, hdh:DMA
hda: IBM-DTLA-307045, ATA DISK drive
hda: DMA disabled
blk: queue c0368940, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: host protected area => 1
hda: 90069840 sectors (46116 MB) w/1916KiB Cache, CHS=5606/255/63, UDMA(100)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 p10 p11 >
SCSI subsystem driver Revision: 1.00
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8
<Adaptec 2940 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
spurious 8259A interrupt: IRQ7.
Vendor: IBM Model: DNES-309170W Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Vendor: TEAC Model: CD-R56S Rev: 1.0P
Type: CD-ROM ANSI SCSI revision: 02
Vendor: PIONEER Model: DVD-ROM DVD-305 Rev: 1.03
Type: CD-ROM ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled. Depth 253
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 31, 16bit)
SCSI device sda: 17916240 512-byte hdwr sectors (9173 MB)
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 >
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
reiserfs: checking transaction log (device 08:02) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 276k freed
Adding Swap: 530104k swap-space (priority -1)
reiserfs: checking transaction log (device 08:05) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 08:06) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 08:07) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 08:08) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 03:07) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 03:09) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 03:0a) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
Real Time Clock Driver v1.10e
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
00:0d.0: 3Com PCI 3c905C Tornado at 0x9400. Vers LK1.1.18-ac
usb-uhci.c: $Revision: 1.275 $ time 00:19:22 Oct 15 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
hub.c: new USB device 00:04.2-1, assigned address 2
hub.c: USB hub found
hub.c: 5 ports detected
hub.c: new USB device 00:04.2-1.4, assigned address 3
usb.c: USB device 3 (vend/prod 0x9ef/0x101) is not claimed by any active driver.
hub.c: new USB device 00:04.2-1.5, assigned address 4
usb.c: USB device 4 (vend/prod 0x43e/0x42bd) is not claimed by any active driver.
[-- Attachment #1.3: dmesg output _with_ the dvb card installed --]
[-- Type: text/plain, Size: 10318 bytes --]
Linux version 2.4.20-pre8-ac3-marcet (root@jerry.marcet.dyndns.org) (gcc version 3.2) #1 Tue Oct 15 00:12:27 CEST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000017fec000 (usable)
BIOS-e820: 0000000017fec000 - 0000000017fef000 (ACPI data)
BIOS-e820: 0000000017fef000 - 0000000017fff000 (reserved)
BIOS-e820: 0000000017fff000 - 0000000018000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
383MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 98284
zone(0): 4096 pages.
zone(1): 94188 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 ASUS ) @ 0x000f6a70
ACPI: RSDT (v001 ASUS A7V-133 12336.12337) @ 0x17fec000
ACPI: FADT (v001 ASUS A7V-133 12336.12337) @ 0x17fec080
ACPI: BOOT (v001 ASUS A7V-133 12336.12337) @ 0x17fec040
ACPI: DSDT (v001 ASUS A7V-133 00000.04096) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: MADT not present
Kernel command line: root=/dev/sda2 video=matrox:mem:32,xres:1280,yres:960,left:264,right:24,hslen:160,upper:47,lower:1,vslen:3,pixclock:6024,sync:0x03,depth:32,pan panicblink=2
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 1544.751 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3039.23 BogoMIPS
Memory: 383020k/393136k available (1663k kernel code, 7552k reserved, 326k data, 276k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
ramfs: mounted with options: <defaults>
ramfs: max_pages=48149 max_file_pages=0 max_inodes=0 max_dentries=48149
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0383fbff c1c3fbff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbff c1c3fbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
CPU: AMD Athlon(TM) XP 1800+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
HZ: Currently used HZ value is (1000)
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1544.0164 MHz.
..... host bus clock speed is 268.0550 MHz.
cpu: 0, clocks: 268550, slice: 134275
CPU0<T0:268544,T1:134256,D:13,S:134275,C:268550>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20021002
PCI: PCI BIOS revision 2.10 entry at 0xf1180, last bus=1
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S3 S4 S5)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Scanning bus 00
Found 00:00 [1106/0305] 000600 00
Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 89 & 1f -> 09
Found 00:08 [1106/8305] 000604 01
Found 00:20 [1106/0686] 000601 00
Found 00:21 [1106/0571] 000101 00
Found 00:22 [1106/3038] 000c03 00
Found 00:23 [1106/3038] 000c03 00
Found 00:24 [1106/3057] 000680 00
Found 00:50 [1131/7146] 000480 00
Found 00:58 [9005/0010] 000100 00
Found 00:60 [109e/036e] 000400 00
Found 00:61 [109e/0878] 000480 00
Found 00:68 [10b7/9200] 000200 00
Found 00:88 [105a/0d30] 000180 00
Fixups for bus 00
Scanning behind PCI bridge 00:01.0, config 010100, pass 0
Scanning bus 01
Found 01:00 [102b/0525] 000300 00
Fixups for bus 01
Bus scan for 01 returning with max=01
Scanning behind PCI bridge 00:01.0, config 010100, pass 1
Bus scan for 00 returning with max=01
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
PCI: Probing PCI hardware
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
PnPBIOS: Found PnP BIOS installation structure at 0xc00fc4f0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc520, dseg 0xf0000
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
PnPBIOS: PNP0c02: ioport range 0xe400-0xe47f has been reserved
PnPBIOS: PNP0c02: ioport range 0xe800-0xe83f could not be reserved
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
SBF: Simple Boot Flag extension found and enabled.
SBF: Setting boot flags 0x1
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1 C2, 16 throttling states)
matroxfb: Matrox Millennium G400 MAX (AGP) detected
matroxfb: MTRR's turned on
matroxfb: 1280x960x32bpp (virtual: 1280x3276)
matroxfb: framebuffer at 0xE2000000, mapped to 0xd880f000, size 33554432
Console: switching to colour frame buffer device 160x60
fb0: MATROX VGA frame buffer device
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:04.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:04.1
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
PDC20265: IDE controller at PCI slot 00:11.0
PDC20265: chipset revision 2
PDC20265: not 100% native mode: will probe irqs later
PDC20265: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode.
PDC20265: FORCING BURST BIT 0x00->0x01 ACTIVE
ide2: BM-DMA at 0x8400-0x8407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0x8408-0x840f, BIOS settings: hdg:DMA, hdh:pio
hda: IBM-DTLA-307045, ATA DISK drive
hda: DMA disabled
blk: queue c0368940, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: host protected area => 1
hda: 90069840 sectors (46116 MB) w/1916KiB Cache, CHS=5606/255/63, UDMA(100)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 p10 p11 >
SCSI subsystem driver Revision: 1.00
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8
<Adaptec 2940 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
spurious 8259A interrupt: IRQ7.
Vendor: IBM Model: DNES-309170W Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Vendor: TEAC Model: CD-R56S Rev: 1.0P
Type: CD-ROM ANSI SCSI revision: 02
Vendor: PIONEER Model: DVD-ROM DVD-305 Rev: 1.03
Type: CD-ROM ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled. Depth 253
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 31, 16bit)
SCSI device sda: 17916240 512-byte hdwr sectors (9173 MB)
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 >
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
reiserfs: checking transaction log (device 08:02) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 276k freed
Adding Swap: 530104k swap-space (priority -1)
reiserfs: checking transaction log (device 08:05) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 08:06) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 08:07) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 08:08) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 03:07) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 03:09) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 03:0a) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
Real Time Clock Driver v1.10e
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
00:0d.0: 3Com PCI 3c905C Tornado at 0xa000. Vers LK1.1.18-ac
usb-uhci.c: $Revision: 1.275 $ time 00:19:22 Oct 15 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
hub.c: new USB device 00:04.2-1, assigned address 2
hub.c: USB hub found
hub.c: 5 ports detected
hub.c: new USB device 00:04.2-1.4, assigned address 3
usb.c: USB device 3 (vend/prod 0x9ef/0x101) is not claimed by any active driver.
hub.c: new USB device 00:04.2-1.5, assigned address 4
usb.c: USB device 4 (vend/prod 0x43e/0x42bd) is not claimed by any active driver.
[-- Attachment #1.4: syslog of bttv's good behavior --]
[-- Type: text/plain, Size: 2002 bytes --]
Oct 15 01:07:24 [kernel] Linux video capture interface: v1.00
Oct 15 01:07:24 [kernel] i2c-core.o: i2c core module version 2.6.5 (20020915)
Oct 15 01:07:25 [kernel] bttv0: Hauppauge eeprom: model=44354, tuner=Temic 4009FR5 (20), radio=yes
Oct 15 01:07:25 [kernel] msp34xx: init: chip=MSP3415D-B3, has NICAM support
Oct 15 01:07:25 [kernel] msp3410: daemon started
Oct 15 01:07:25 [kernel] bttv0: i2c attach [client=MSP3415D-B3,ok]
Oct 15 01:07:25 [kernel] tvaudio: TV audio decoder + audio/video mux driver
Oct 15 01:07:25 [kernel] tuner: probing bt848 #0 i2c adapter [id=0x10005]
Oct 15 01:07:25 [kernel] tuner: chip found @ 0xc2
Oct 15 01:07:25 [kernel] msp3410: setting mode: autodetect start (0x0001)
Oct 15 01:07:25 [kernel] msp3410: detection still in progress
Oct 15 01:07:25 [kernel] msp3410: detection still in progress
Oct 15 01:07:25 [kernel] msp3410: current mode: ERROR (0x0000)
Oct 15 01:07:25 [kernel] msp34xx: setbass: 32768 0x00
Oct 15 01:07:39 [kernel] bttv0: open called
Oct 15 01:07:39 [kernel] Display at e2000000 is 1280 by 3276, bytedepth 4, bpl 5120
Oct 15 01:07:40 [kernel] msp3410: setting mode: autodetect start (0x0001)
Oct 15 01:07:40 [kernel] msp3410: detection still in progress
Oct 15 01:07:40 [kernel] msp3410: current mode: 5.5/5.85 B/G NICAM FM (0x0008)
Oct 15 01:07:41 [kernel] msp3410: setting mode: autodetect start (0x0001)
Oct 15 01:07:41 [kernel] msp3410: detection still in progress
Oct 15 01:07:41 [kernel] msp3410: detection still in progress
Oct 15 01:07:41 [kernel] msp3410: current mode: 5.5/5.74 B/G Dual FM-Stereo (0x0003)
Oct 15 01:07:42 [kernel] msp34xx: stereo detect register: 0
Oct 15 01:07:47 [kernel] bttv0: clip: ro=12828000 re=12820000
Oct 15 01:07:56 [kernel] bttv0: clip: ro=12828000 re=12820000
Oct 15 01:08:09 [kernel] bttv0: clip: ro=12828000 re=12820000
Oct 15 01:08:44 [kernel] bttv0: unloading
Oct 15 01:08:44 [kernel] msp3410: thread: exit
Oct 15 01:08:57 [fcron] SIGTERM signal received
Oct 15 01:08:57 [fcron] Exiting with code 0
[-- Attachment #1.5: syslog of bttv's errors when the dvb board is also installed --]
[-- Type: text/plain, Size: 3625 bytes --]
Oct 15 00:51:22 [kernel] Linux video capture interface: v1.00
Oct 15 00:51:22 [kernel] i2c-core.o: i2c core module version 2.6.5 (20020915)
Oct 15 00:51:22 [kernel] bttv0: Hauppauge eeprom: model=44354, tuner=Temic 4009FR5 (20), radio=yes
Oct 15 00:51:22 [kernel] msp34xx: init: chip=MSP3415D-B3, has NICAM support
Oct 15 00:51:22 [kernel] msp3410: daemon started
Oct 15 00:51:22 [kernel] bttv0: i2c attach [client=MSP3415D-B3,ok]
Oct 15 00:51:22 [kernel] tvaudio: TV audio decoder + audio/video mux driver
Oct 15 00:51:22 [kernel] tuner: probing bt848 #0 i2c adapter [id=0x10005]
Oct 15 00:51:22 [kernel] tuner: chip found @ 0xc2
Oct 15 00:51:22 [kernel] bttv0: registered device video0
Oct 15 00:51:33 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x9
Oct 15 00:51:33 [kernel] bttv0: irq: SCERR risc_count=12670014
Oct 15 00:51:33 [kernel] bttv0: irq: SCERR risc_count=12670014
Oct 15 00:51:38 [kernel] bttv0: resetting chip
Oct 15 00:51:38 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x8
Oct 15 00:51:38 [kernel] bttv0: irq: SCERR risc_count=12670014
Oct 15 00:51:38 [kernel] bttv0: irq: SCERR risc_count=12670014
Oct 15 00:51:38 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x9
Oct 15 00:51:38 [kernel] bttv0: irq: SCERR risc_count=12670000
Oct 15 00:54:45 [kernel] Linux video capture interface: v1.00
Oct 15 00:54:45 [kernel] i2c-core.o: i2c core module version 2.6.5 (20020915)
Oct 15 00:54:45 [kernel] msp34xx: init: chip=MSP3415D-B3, has NICAM support
Oct 15 00:54:45 [kernel] msp3410: daemon started
Oct 15 00:54:45 [kernel] bttv0: i2c attach [client=MSP3415D-B3,ok]
Oct 15 00:54:45 [kernel] tvaudio: TV audio decoder + audio/video mux driver
Oct 15 00:54:45 [kernel] tuner: probing bt848 #0 i2c adapter [id=0x10005]
Oct 15 00:54:45 [kernel] tuner: chip found @ 0xc2
Oct 15 00:54:45 [kernel] msp3410: setting mode: autodetect start (0x0001)
Oct 15 00:54:45 [kernel] msp3410: detection still in progress
Oct 15 00:54:45 [kernel] msp3410: current mode: 5.5/5.85 B/G NICAM FM (0x0008)
Oct 15 00:54:45 [kernel] msp3400: NICAM setstereo: stereo
Oct 15 00:54:46 [kernel] msp34xx: nicam sync=1, mode=8
Oct 15 00:54:54 [kernel] bttv0: open called
Oct 15 00:54:54 [kernel] Display at e2000000 is 1280 by 3276, bytedepth 4, bpl 5120
Oct 15 00:54:54 [kernel] bttv0: open called
Oct 15 00:54:54 [kernel] bttv0: open called
Oct 15 00:54:54 [kernel] msp34xx: nicam sync=1, mode=8
Oct 15 00:54:54 [kernel] msp34xx: nicam sync=1, mode=8
Oct 15 00:54:54 [kernel] msp34xx: nicam sync=1, mode=8
Oct 15 00:54:54 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x8
Oct 15 00:54:55 [kernel] msp3410: setting mode: autodetect start (0x0001)
Oct 15 00:54:55 [kernel] msp3410: detection still in progress
Oct 15 00:54:55 [kernel] msp3410: current mode: 5.5/5.85 B/G NICAM FM (0x0008)
Oct 15 00:54:56 [kernel] msp34xx: nicam sync=1, mode=8
Oct 15 00:54:59 [kernel] bttv0: resetting chip
Oct 15 00:55:00 [kernel] ok
Oct 15 00:55:00 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x8
Oct 15 00:55:00 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x8
Oct 15 00:55:00 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x8
Oct 15 00:55:01 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x9
Oct 15 00:55:01 [kernel] msp3410: setting mode: autodetect start (0x0001)
Oct 15 00:55:01 [kernel] msp3410: detection still in progress
Oct 15 00:55:01 [kernel] msp3410: detection still in progress
Oct 15 00:55:01 [kernel] msp3410: current mode: 5.5/5.74 B/G Dual FM-Stereo (0x0003)
Oct 15 00:55:02 [kernel] msp34xx: stereo detect register: 0
Oct 15 00:55:05 [kernel] bttv0: unloading
Oct 15 00:55:05 [kernel] msp3410: thread: exit
[-- Attachment #1.6: lspci-> bttv +/- correctly identified by the kernel --]
[-- Type: text/plain, Size: 4858 bytes --]
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03)
Subsystem: Asustek Computer, Inc. A7V133/A7V133-C Mainboard
Flags: bus master, medium devsel, latency 8
Memory at e4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2
00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: df000000-e06fffff
Prefetchable memory behind bridge: e1f00000-e3ffffff
Capabilities: [80] Power Management version 2
00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: Asustek Computer, Inc. A7V133/A7V133-C Mainboard
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
00:04.1 IDE interface: VIA Technologies, Inc. VT82C586B PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 32
I/O ports at d800 [size=16]
Capabilities: [c0] Power Management version 2
00:04.2 USB Controller: VIA Technologies, Inc. USB (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 9
I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
00:04.3 USB Controller: VIA Technologies, Inc. USB (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 9
I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
00:04.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: Asustek Computer, Inc. A7V133/A7V133-C Mainboard
Flags: medium devsel, IRQ 9
Capabilities: [68] Power Management version 2
00:09.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 04)
Subsystem: Creative Labs CT4620 SBLive!
Flags: bus master, medium devsel, latency 32, IRQ 9
I/O ports at a400 [size=32]
Capabilities: [dc] Power Management version 1
00:09.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 01)
Subsystem: Creative Labs Gameport Joystick
Flags: bus master, medium devsel, latency 32
I/O ports at a000 [size=8]
Capabilities: [dc] Power Management version 1
00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV/GO
Flags: bus master, medium devsel, latency 32, IRQ 15
Memory at e1000000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
00:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV/GO
Flags: bus master, medium devsel, latency 32, IRQ 15
Memory at e0800000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
00:0b.0 SCSI storage controller: Adaptec AHA-2940U2/U2W
Subsystem: Adaptec AHA-2940U2W SCSI Controller
Flags: bus master, medium devsel, latency 32, IRQ 10
BIST result: 00
I/O ports at 9800 [disabled] [size=256]
Memory at de800000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 1
00:0d.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74)
Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC
Flags: bus master, medium devsel, latency 32, IRQ 9
I/O ports at 9400 [size=128]
Memory at de000000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
00:11.0 Unknown mass storage controller: Promise Technology, Inc. 20265 (rev 02)
Subsystem: Promise Technology, Inc. Ultra100
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at 9000 [size=8]
I/O ports at 8800 [size=4]
I/O ports at 8400 [size=8]
I/O ports at 8000 [size=4]
I/O ports at 7800 [size=64]
Memory at dd800000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [58] Power Management version 1
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 03) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G400 MAX/Dual Head 32Mb
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at e2000000 (32-bit, prefetchable) [size=32M]
Memory at df800000 (32-bit, non-prefetchable) [size=16K]
Memory at df000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at e1ff0000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Capabilities: [f0] AGP version 2.0
[-- Attachment #1.7: lspci-> bttv as unknown card when dvb board is in --]
[-- Type: text/plain, Size: 3625 bytes --]
Oct 15 00:51:22 [kernel] Linux video capture interface: v1.00
Oct 15 00:51:22 [kernel] i2c-core.o: i2c core module version 2.6.5 (20020915)
Oct 15 00:51:22 [kernel] bttv0: Hauppauge eeprom: model=44354, tuner=Temic 4009FR5 (20), radio=yes
Oct 15 00:51:22 [kernel] msp34xx: init: chip=MSP3415D-B3, has NICAM support
Oct 15 00:51:22 [kernel] msp3410: daemon started
Oct 15 00:51:22 [kernel] bttv0: i2c attach [client=MSP3415D-B3,ok]
Oct 15 00:51:22 [kernel] tvaudio: TV audio decoder + audio/video mux driver
Oct 15 00:51:22 [kernel] tuner: probing bt848 #0 i2c adapter [id=0x10005]
Oct 15 00:51:22 [kernel] tuner: chip found @ 0xc2
Oct 15 00:51:22 [kernel] bttv0: registered device video0
Oct 15 00:51:33 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x9
Oct 15 00:51:33 [kernel] bttv0: irq: SCERR risc_count=12670014
Oct 15 00:51:33 [kernel] bttv0: irq: SCERR risc_count=12670014
Oct 15 00:51:38 [kernel] bttv0: resetting chip
Oct 15 00:51:38 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x8
Oct 15 00:51:38 [kernel] bttv0: irq: SCERR risc_count=12670014
Oct 15 00:51:38 [kernel] bttv0: irq: SCERR risc_count=12670014
Oct 15 00:51:38 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x9
Oct 15 00:51:38 [kernel] bttv0: irq: SCERR risc_count=12670000
Oct 15 00:54:45 [kernel] Linux video capture interface: v1.00
Oct 15 00:54:45 [kernel] i2c-core.o: i2c core module version 2.6.5 (20020915)
Oct 15 00:54:45 [kernel] msp34xx: init: chip=MSP3415D-B3, has NICAM support
Oct 15 00:54:45 [kernel] msp3410: daemon started
Oct 15 00:54:45 [kernel] bttv0: i2c attach [client=MSP3415D-B3,ok]
Oct 15 00:54:45 [kernel] tvaudio: TV audio decoder + audio/video mux driver
Oct 15 00:54:45 [kernel] tuner: probing bt848 #0 i2c adapter [id=0x10005]
Oct 15 00:54:45 [kernel] tuner: chip found @ 0xc2
Oct 15 00:54:45 [kernel] msp3410: setting mode: autodetect start (0x0001)
Oct 15 00:54:45 [kernel] msp3410: detection still in progress
Oct 15 00:54:45 [kernel] msp3410: current mode: 5.5/5.85 B/G NICAM FM (0x0008)
Oct 15 00:54:45 [kernel] msp3400: NICAM setstereo: stereo
Oct 15 00:54:46 [kernel] msp34xx: nicam sync=1, mode=8
Oct 15 00:54:54 [kernel] bttv0: open called
Oct 15 00:54:54 [kernel] Display at e2000000 is 1280 by 3276, bytedepth 4, bpl 5120
Oct 15 00:54:54 [kernel] bttv0: open called
Oct 15 00:54:54 [kernel] bttv0: open called
Oct 15 00:54:54 [kernel] msp34xx: nicam sync=1, mode=8
Oct 15 00:54:54 [kernel] msp34xx: nicam sync=1, mode=8
Oct 15 00:54:54 [kernel] msp34xx: nicam sync=1, mode=8
Oct 15 00:54:54 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x8
Oct 15 00:54:55 [kernel] msp3410: setting mode: autodetect start (0x0001)
Oct 15 00:54:55 [kernel] msp3410: detection still in progress
Oct 15 00:54:55 [kernel] msp3410: current mode: 5.5/5.85 B/G NICAM FM (0x0008)
Oct 15 00:54:56 [kernel] msp34xx: nicam sync=1, mode=8
Oct 15 00:54:59 [kernel] bttv0: resetting chip
Oct 15 00:55:00 [kernel] ok
Oct 15 00:55:00 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x8
Oct 15 00:55:00 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x8
Oct 15 00:55:00 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x8
Oct 15 00:55:01 [kernel] scsi0: PCI error Interrupt at seqaddr = 0x9
Oct 15 00:55:01 [kernel] msp3410: setting mode: autodetect start (0x0001)
Oct 15 00:55:01 [kernel] msp3410: detection still in progress
Oct 15 00:55:01 [kernel] msp3410: detection still in progress
Oct 15 00:55:01 [kernel] msp3410: current mode: 5.5/5.74 B/G Dual FM-Stereo (0x0003)
Oct 15 00:55:02 [kernel] msp34xx: stereo detect register: 0
Oct 15 00:55:05 [kernel] bttv0: unloading
Oct 15 00:55:05 [kernel] msp3410: thread: exit
[-- Attachment #2: Type: application/pgp-signature, Size: 197 bytes --]
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2002-10-14 23:54 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2002-10-14 23:54 bttv and DVB cards hardware incompaibility only in late linux Javier Marcet
2002-10-15 0:07 ` Javier Marcet
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®