* [updated patch] for efi support in ia32 kernels
@ 2003-10-03 21:46 Tolentino, Matthew E
2003-10-04 6:00 ` Andrew Morton
2003-10-04 6:55 ` Andrew Morton
0 siblings, 2 replies; 3+ messages in thread
From: Tolentino, Matthew E @ 2003-10-03 21:46 UTC (permalink / raw)
To: akpm, ebiederm; +Cc: linux-kernel
[-- Attachment #1: Type: text/plain, Size: 2513 bytes --]
Attached is another patch that enables EFI boot-up support in ia32 kernels. This one has numerous changes based on the various comments and suggestions made on the last one several weeks ago. The patch is against 2.6.0-test6-mm2.
This patch departs from the last in that I am no longer adding separate boot parameters at the end of the the empty_zero_page; rather, based on Eric's suggestion, I've added EFI parameters via offset grouped with the rest of the existing boot parameters. This allows the reuse of several parameters which were redundant (command-line, initrd, etc.). This also simplifies some of the code in setup_arch().
In order to continue to determine whether the kernel should initialize using EFI tables, I've temporarily added a check on the LOADER_TYPE boot parameter. Although I haven't requested that elilo be assigned an id for this yet, I've used this to determine whether the kernel should use the EFI initialization path as well as a check to see if the EFI_SYSTAB boot parameter contains anything. If someone has a better suggestion for determining this, I'm open...
This patch also uses the existing ioremapping functions to map the efi tables into kernel virtual address space. I've added an option such that I could use Dave Hansen's boot_ioremap() before paging_init(). After paging_init, I then remap the efi memmap using bt_ioremap for use later. This has eliminated the need for several functions...thanks for the suggestions and thanks for your help Dave. Still this could use a look-see.
Something else that I'd like to solicit suggestions on is how to deal with CONFIG_ACPI_EFI. One of the goals of this patch is to enable the kernel to "just know" at boot time when to use EFI information to initialize. That way, the same kernel image would theoretically still boot on existing systems with a different BIOS. I think this patch accomplishes that goal to some degree, but how best to deal with when/when not to look at the EFI config table for the RSDP is still dealt with at compile time. I'd like to dynamically determine this as well, but am not sure of the best way...suggestions? Len? Andrew?
Note, I'm still working on verifying this works properly on a system with >4GB system memory, as well as with the 4G/4G split (hence the reason this is against the -mm kernel)...hopefully, I'll be able to steal some time on one of those monsters next week.
Comments and suggestions are welcome...
thanks,
matt
[-- Attachment #2: linux-2.6.0-test6-mm2-efi.patch --]
[-- Type: application/octet-stream, Size: 41749 bytes --]
diff -urN linux-2.6.0-test6-mm2/arch/i386/Kconfig linux-2.6.0-test6-mm2-efi/arch/i386/Kconfig
--- linux-2.6.0-test6-mm2/arch/i386/Kconfig 2003-10-03 11:50:44.000000000 -0700
+++ linux-2.6.0-test6-mm2-efi/arch/i386/Kconfig 2003-10-03 10:10:40.000000000 -0700
@@ -840,8 +840,9 @@
# turning this on wastes a bunch of space.
# Summit needs it only when NUMA is on
config BOOT_IOREMAP
- bool
- depends on ((X86_SUMMIT || X86_GENERICARCH) && NUMA)
+ bool
+ depends on (((X86_SUMMIT || X86_GENERICARCH) && NUMA)) || X86_GENERICARCH
default y
endmenu
diff -urN linux-2.6.0-test6-mm2/arch/i386/kernel/acpi/boot.c linux-2.6.0-test6-mm2-efi/arch/i386/kernel/acpi/boot.c
--- linux-2.6.0-test6-mm2/arch/i386/kernel/acpi/boot.c 2003-10-03 11:50:44.000000000 -0700
+++ linux-2.6.0-test6-mm2-efi/arch/i386/kernel/acpi/boot.c 2003-10-03 10:10:40.000000000 -0700
@@ -26,6 +26,7 @@
#include <linux/init.h>
#include <linux/config.h>
#include <linux/acpi.h>
+#include <linux/efi.h>
#include <asm/pgalloc.h>
#include <asm/io_apic.h>
#include <asm/apic.h>
@@ -295,7 +296,11 @@
acpi_find_rsdp (void)
{
unsigned long rsdp_phys = 0;
-
+
+ if (efi.acpi20)
+ return __pa(efi.acpi20);
+ else if (efi.acpi)
+ return __pa(efi.acpi);
/*
* Scan memory looking for the RSDP signature. First search EBDA (low
* memory) paragraphs and then search upper memory (E0000-FFFFF).
diff -urN linux-2.6.0-test6-mm2/arch/i386/kernel/efi.c linux-2.6.0-test6-mm2-efi/arch/i386/kernel/efi.c
--- linux-2.6.0-test6-mm2/arch/i386/kernel/efi.c 1969-12-31 16:00:00.000000000 -0800
+++ linux-2.6.0-test6-mm2-efi/arch/i386/kernel/efi.c 2003-10-03 11:44:45.000000000 -0700
@@ -0,0 +1,606 @@
+/*
+ * Extensible Firmware Interface
+ *
+ * Based on Extensible Firmware Interface Specification version 1.0
+ *
+ * Copyright (C) 1999 VA Linux Systems
+ * Copyright (C) 1999 Walt Drummond <drummond@valinux.com>
+ * Copyright (C) 1999-2002 Hewlett-Packard Co.
+ * David Mosberger-Tang <davidm@hpl.hp.com>
+ * Stephane Eranian <eranian@hpl.hp.com>
+ *
+ * All EFI Runtime Services are not implemented yet as EFI only
+ * supports physical mode addressing on SoftSDV. This is to be fixed
+ * in a future version. --drummond 1999-07-20
+ *
+ * Implemented EFI runtime services and virtual mode calls. --davidm
+ *
+ * Goutham Rao: <goutham.rao@intel.com>
+ * Skip non-WB memory and ignore empty memory ranges.
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/types.h>
+#include <linux/time.h>
+#include <linux/spinlock.h>
+#include <linux/bootmem.h>
+#include <linux/ioport.h>
+#include <linux/proc_fs.h>
+#include <linux/efi.h>
+
+#include <asm/setup.h>
+#include <asm/io.h>
+#include <asm/page.h>
+#include <asm/pgtable.h>
+#include <asm/processor.h>
+#include <asm/desc.h>
+#include <asm/pgalloc.h>
+#include <asm/tlbflush.h>
+
+#define EFI_DEBUG 0
+#define PFX "EFI: "
+
+extern efi_status_t asmlinkage efi_call_phys(void *, ...);
+
+struct efi efi;
+struct efi efi_phys __initdata;
+struct efi_memory_map memmap __initdata;
+
+/*
+ * We require an early boot_ioremap mapping mechanism initially
+ */
+extern void * boot_ioremap(unsigned long, unsigned long);
+
+/*
+ * efi_dir is allocated here, but the directory isn't created
+ * here, as proc_mkdir() doesn't work this early in the bootup
+ * process. Therefore, each module, like efivars, must test for
+ * if (!efi_dir) efi_dir = proc_mkdir("efi", NULL);
+ * prior to creating their own entries under /proc/efi.
+ */
+#ifdef CONFIG_PROC_FS
+struct proc_dir_entry *efi_dir;
+#endif
+
+
+/*
+ * To make EFI call EFI runtime service in physical addressing mode we need
+ * prelog/epilog before/after the invocation to disable interrupt, to
+ * claim EFI runtime service handler exclusively and to duplicate a memory in
+ * low memory space say 0 - 3G.
+ */
+
+static unsigned long efi_rt_eflags;
+static spinlock_t efi_rt_lock = SPIN_LOCK_UNLOCKED;
+static pgd_t efi_bak_pg_dir_pointer[2];
+
+static void efi_call_phys_prelog(void)
+{
+ unsigned long cr4;
+ unsigned long temp;
+
+ spin_lock(&efi_rt_lock);
+ local_irq_save(efi_rt_eflags);
+
+ /*
+ * If I don't have PSE, I should just duplicate two entries in page
+ * directory. If I have PSE, I just need to duplicate one entry in
+ * page directory.
+ */
+ __asm__ __volatile__("movl %%cr4, %0":"=r"(cr4));
+
+ if (cr4 & X86_CR4_PSE) {
+ efi_bak_pg_dir_pointer[0].pgd =
+ swapper_pg_dir[pgd_index(0)].pgd;
+ swapper_pg_dir[0].pgd =
+ swapper_pg_dir[pgd_index(PAGE_OFFSET)].pgd;
+ } else {
+ efi_bak_pg_dir_pointer[0].pgd =
+ swapper_pg_dir[pgd_index(0)].pgd;
+ efi_bak_pg_dir_pointer[1].pgd =
+ swapper_pg_dir[pgd_index(0x400000)].pgd;
+ swapper_pg_dir[pgd_index(0)].pgd =
+ swapper_pg_dir[pgd_index(PAGE_OFFSET)].pgd;
+ temp = PAGE_OFFSET + 0x400000;
+ swapper_pg_dir[pgd_index(0x400000)].pgd =
+ swapper_pg_dir[pgd_index(temp)].pgd;
+ }
+
+ /*
+ * After the lock is released, the original page table is restored.
+ */
+ local_flush_tlb();
+
+ cpu_gdt_descr[0].address = __pa(cpu_gdt_descr[0].address);
+ __asm__ __volatile__("lgdt %0":"=m"
+ (*(struct Xgt_desc_struct *) __pa(&cpu_gdt_descr[0])));
+}
+
+static void efi_call_phys_epilog(void)
+{
+ unsigned long cr4;
+
+ cpu_gdt_descr[0].address =
+ (unsigned long) __va(cpu_gdt_descr[0].address);
+ __asm__ __volatile__("lgdt %0":"=m"(cpu_gdt_descr));
+ __asm__ __volatile__("movl %%cr4, %0":"=r"(cr4));
+
+ if (cr4 & X86_CR4_PSE) {
+ swapper_pg_dir[pgd_index(0)].pgd =
+ efi_bak_pg_dir_pointer[0].pgd;
+ } else {
+ swapper_pg_dir[pgd_index(0)].pgd =
+ efi_bak_pg_dir_pointer[0].pgd;
+ swapper_pg_dir[pgd_index(0x400000)].pgd =
+ efi_bak_pg_dir_pointer[1].pgd;
+ }
+
+ /*
+ * After the lock is released, the original page table is restored.
+ */
+ local_flush_tlb();
+
+ local_irq_restore(efi_rt_eflags);
+ spin_unlock(&efi_rt_lock);
+}
+
+static efi_status_t
+phys_efi_set_virtual_address_map(unsigned long memory_map_size,
+ unsigned long descriptor_size,
+ u32 descriptor_version,
+ efi_memory_desc_t *virtual_map)
+{
+ efi_status_t status;
+
+ efi_call_phys_prelog();
+ status = efi_call_phys(efi_phys.set_virtual_address_map,
+ memory_map_size, descriptor_size,
+ descriptor_version, virtual_map);
+ efi_call_phys_epilog();
+ return status;
+}
+
+efi_status_t
+phys_efi_get_time(efi_time_t *tm, efi_time_cap_t *tc)
+{
+ efi_status_t status;
+
+ efi_call_phys_prelog();
+ status = efi_call_phys(efi_phys.get_time, tm, tc);
+ efi_call_phys_epilog();
+ return status;
+}
+
+void efi_gettimeofday(struct timespec *tv)
+{
+ efi_time_t tm;
+
+ memset(tv, 0, sizeof(*tv));
+ if ((*efi.get_time) (&tm, 0) != EFI_SUCCESS)
+ return;
+
+ tv->tv_sec = mktime(tm.year, tm.month, tm.day, tm.hour, tm.minute,
+ tm.second);
+ tv->tv_nsec = tm.nanosecond;
+}
+
+int is_available_memory(efi_memory_desc_t * md)
+{
+ if (!(md->attribute & EFI_MEMORY_WB))
+ return 0;
+
+ switch (md->type) {
+ case EFI_LOADER_CODE:
+ case EFI_LOADER_DATA:
+ case EFI_BOOT_SERVICES_CODE:
+ case EFI_BOOT_SERVICES_DATA:
+ case EFI_CONVENTIONAL_MEMORY:
+ return 1;
+ }
+ return 0;
+}
+
+/*
+ * We need to map the EFI memory map again after paging_init().
+ */
+void __init efi_map_memmap(void)
+{
+ memmap.map = NULL;
+
+ memmap.map = (efi_memory_desc_t *)
+ bt_ioremap((unsigned long) memmap.phys_map,
+ (memmap.nr_map * sizeof(efi_memory_desc_t)));
+
+ if (memmap.map == NULL)
+ printk(KERN_ERR PFX "Could not remap the EFI memmap!\n");
+}
+
+void __init print_efi_memmap(void)
+{
+ efi_memory_desc_t *md;
+ int i;
+
+ for (i = 0; i < memmap.nr_map; i++) {
+ md = &memmap.map[i];
+ printk(KERN_INFO "mem%02u: type=%u, attr=0x%llx, "
+ "range=[0x%016llx-0x%016llx) (%lluMB)\n",
+ i, md->type, md->attribute, md->phys_addr,
+ md->phys_addr + (md->num_pages << EFI_PAGE_SHIFT),
+ (md->num_pages >> (20 - EFI_PAGE_SHIFT)));
+ }
+}
+
+/*
+ * Walks the EFI memory map and calls CALLBACK once for each EFI
+ * memory descriptor that has memory that is available for kernel use.
+ */
+void efi_memmap_walk(efi_freemem_callback_t callback, void *arg)
+{
+ int prev_valid = 0;
+ struct range {
+ unsigned long start;
+ unsigned long end;
+ } prev, curr;
+ efi_memory_desc_t *md;
+ unsigned long start, end;
+ int i;
+
+ for (i = 0; i < memmap.nr_map; i++) {
+ md = &memmap.map[i];
+
+ if ((md->num_pages == 0) || (!is_available_memory(md)))
+ continue;
+
+ curr.start = md->phys_addr;
+ curr.end = curr.start + (md->num_pages << EFI_PAGE_SHIFT);
+
+ if (!prev_valid) {
+ prev = curr;
+ prev_valid = 1;
+ } else {
+ if (curr.start < prev.start)
+ printk(KERN_INFO PFX "Unordered memory map\n");
+ if (prev.end == curr.start)
+ prev.end = curr.end;
+ else {
+ start =
+ (unsigned long) (PAGE_ALIGN(prev.start));
+ end = (unsigned long) (prev.end & PAGE_MASK);
+ if ((end > start)
+ && (*callback) (start, end, arg) < 0)
+ return;
+ prev = curr;
+ }
+ }
+ }
+ if (prev_valid) {
+ start = (unsigned long) PAGE_ALIGN(prev.start);
+ end = (unsigned long) (prev.end & PAGE_MASK);
+ if (end > start)
+ (*callback) (start, end, arg);
+ }
+}
+
+void __init efi_init(void)
+{
+ efi_config_table_t *config_tables;
+ efi_runtime_services_t *runtime;
+ efi_char16_t *c16;
+ char vendor[100] = "unknown";
+ unsigned long num_config_tables;
+ int i = 0;
+
+ memset(&efi, 0, sizeof(efi) );
+ memset(&efi_phys, 0, sizeof(efi_phys));
+
+ efi_phys.systab = EFI_SYSTAB;
+ memmap.phys_map = EFI_MEMMAP;
+ memmap.nr_map = EFI_MEMMAP_SIZE/EFI_MEMDESC_SIZE;
+ memmap.desc_version = EFI_MEMDESC_VERSION;
+
+ efi.systab = (efi_system_table_t *)
+ boot_ioremap((unsigned long) efi_phys.systab,
+ sizeof(efi_system_table_t));
+ /*
+ * Verify the EFI Table
+ */
+ if (efi.systab == NULL)
+ printk(KERN_ERR PFX "Woah! Couldn't map the EFI system table.\n");
+ if (efi.systab->hdr.signature != EFI_SYSTEM_TABLE_SIGNATURE)
+ printk(KERN_ERR PFX "Woah! EFI system table signature incorrect\n");
+ if ((efi.systab->hdr.revision ^ EFI_SYSTEM_TABLE_REVISION) >> 16 != 0)
+ printk(KERN_ERR PFX
+ "Warning: EFI system table major version mismatch: "
+ "got %d.%02d, expected %d.%02d\n",
+ efi.systab->hdr.revision >> 16,
+ efi.systab->hdr.revision & 0xffff,
+ EFI_SYSTEM_TABLE_REVISION >> 16,
+ EFI_SYSTEM_TABLE_REVISION & 0xffff);
+ /*
+ * Grab some details from the system table
+ */
+ num_config_tables = efi.systab->nr_tables;
+ config_tables = (efi_config_table_t *)efi.systab->tables;
+ runtime = efi.systab->runtime;
+
+ /*
+ * Show what we know for posterity
+ */
+ c16 = (efi_char16_t *) boot_ioremap(efi.systab->fw_vendor, 2);
+ if (c16) {
+ for (i = 0; i < sizeof(vendor) && *c16; ++i)
+ vendor[i] = *c16++;
+ vendor[i] = '\0';
+ } else
+ printk(KERN_ERR PFX "Could not map the firmware vendor!\n");
+
+ printk(KERN_INFO PFX "EFI v%u.%.02u by %s \n",
+ efi.systab->hdr.revision >> 16,
+ efi.systab->hdr.revision & 0xffff, vendor);
+
+ /*
+ * Let's see what config tables the firmware passed to us.
+ */
+ config_tables = (efi_config_table_t *)
+ boot_ioremap((unsigned long) config_tables,
+ num_config_tables * sizeof(efi_config_table_t));
+
+ if (config_tables == NULL)
+ printk(KERN_ERR PFX "Could not map EFI Configuration Table!\n");
+
+ for (i = 0; i < num_config_tables; i++) {
+ if (efi_guidcmp(config_tables[i].guid, MPS_TABLE_GUID) == 0) {
+ efi.mps = (void *)config_tables[i].table;
+ printk(KERN_INFO " MPS=0x%lx ", config_tables[i].table);
+ } else
+ if (efi_guidcmp(config_tables[i].guid, ACPI_20_TABLE_GUID) == 0) {
+ efi.acpi20 = __va(config_tables[i].table);
+ printk(KERN_INFO " ACPI 2.0=0x%lx ", config_tables[i].table);
+ } else
+ if (efi_guidcmp(config_tables[i].guid, ACPI_TABLE_GUID) == 0) {
+ efi.acpi = __va(config_tables[i].table);
+ printk(KERN_INFO " ACPI=0x%lx ", config_tables[i].table);
+ } else
+ if (efi_guidcmp(config_tables[i].guid, SMBIOS_TABLE_GUID) == 0) {
+ efi.smbios = (void *) config_tables[i].table;
+ printk(KERN_INFO " SMBIOS=0x%lx ", config_tables[i].table);
+ } else
+ if (efi_guidcmp(config_tables[i].guid, HCDP_TABLE_GUID) == 0) {
+ efi.hcdp = (void *)config_tables[i].table;
+ printk(KERN_INFO " HCDP=0x%lx ", config_tables[i].table);
+ } else
+ if (efi_guidcmp(config_tables[i].guid, UGA_IO_PROTOCOL_GUID) == 0) {
+ efi.uga = (void *)config_tables[i].table;
+ printk(KERN_INFO " UGA=0x%lx ", config_tables[i].table);
+ }
+ }
+ printk("\n");
+
+ /*
+ * Check out the runtime services table. We need to map
+ * the runtime services table so that we can grab the physical
+ * address of several of the EFI runtime functions, needed to
+ * set the firmware into virtual mode.
+ */
+
+ runtime = (efi_runtime_services_t *) boot_ioremap((unsigned long)
+ runtime,
+ sizeof(efi_runtime_services_t));
+ if (runtime != NULL) {
+ /*
+ * We will only need *early* access to the following
+ * two EFI runtime services before set_virtual_address_map
+ * is invoked.
+ */
+ efi_phys.get_time = (efi_get_time_t *) runtime->get_time;
+ efi_phys.set_virtual_address_map =
+ (efi_set_virtual_address_map_t *)
+ runtime->set_virtual_address_map;
+ } else
+ printk(KERN_ERR PFX "Could not map the runtime service table!\n");
+
+ /* Map the EFI memory map for use until paging_init() */
+
+ memmap.map = (efi_memory_desc_t *)
+ boot_ioremap((unsigned long) EFI_MEMMAP, EFI_MEMMAP_SIZE);
+
+ if (memmap.map == NULL)
+ printk(KERN_ERR PFX "Could not map the EFI memory map!\n");
+
+ if (EFI_MEMDESC_SIZE != sizeof(efi_memory_desc_t)) {
+ printk(KERN_WARNING PFX "Warning! Kernel-defined memdesc doesn't "
+ "match the one from EFI!\n");
+ }
+#if EFI_DEBUG
+ print_efi_memmap();
+#endif
+}
+
+/*
+ * This function will switch the EFI runtime services to virtual mode.
+ * Essentially, look through the EFI memmap and map every region that
+ * has the runtime attribute bit set in its memory descriptor and update
+ * that memory descriptor with the virtual address obtained from ioremap().
+ * This enables the runtime services to be called without having to
+ * thunk back into physical mode for every invocation.
+ */
+
+void __init efi_enter_virtual_mode(void)
+{
+ efi_memory_desc_t *md;
+ efi_status_t status;
+ int i;
+
+ efi.systab = NULL;
+
+ for (i = 0; i < memmap.nr_map; i++) {
+ md = &memmap.map[i];
+
+ if (md->attribute & EFI_MEMORY_RUNTIME) {
+ md->virt_addr =
+ (u64) ioremap((unsigned long) md->phys_addr,
+ (unsigned long) (md->num_pages
+ << EFI_PAGE_SHIFT));
+ if (!(unsigned long) md->virt_addr) {
+ printk(KERN_ERR PFX "ioremap of md: 0x%lX failed \n",
+ (unsigned long) md->phys_addr);
+ }
+
+ if (((unsigned long)md->phys_addr <= (unsigned long)efi_phys.systab) && ((unsigned long)efi_phys.systab < md->phys_addr + ((unsigned long) md->num_pages << EFI_PAGE_SHIFT))) {
+ efi.systab = (efi_system_table_t *)
+ ((md->virt_addr - md->phys_addr) +
+ (u64)efi_phys.systab);
+ }
+ }
+ }
+
+ if (!efi.systab)
+ BUG();
+
+ status = phys_efi_set_virtual_address_map(
+ sizeof(efi_memory_desc_t) * memmap.nr_map,
+ sizeof(efi_memory_desc_t),
+ memmap.desc_version,
+ memmap.phys_map);
+
+ if (status != EFI_SUCCESS) {
+ printk (KERN_ALERT "You are screwed! "
+ "Unable to switch EFI into virtual mode "
+ "(status=%lx)\n", status);
+ panic("EFI call to SetVirtualAddressMap() failed!");
+ }
+
+ /*
+ * Now that EFI is in virtual mode, update the function
+ * pointers in the runtime service table to the new virtual addresses.
+ */
+
+ efi.get_time = (efi_get_time_t *) efi.systab->runtime->get_time;
+ efi.set_time = (efi_set_time_t *) efi.systab->runtime->set_time;
+ efi.get_wakeup_time = (efi_get_wakeup_time_t *)
+ efi.systab->runtime->get_wakeup_time;
+ efi.set_wakeup_time = (efi_set_wakeup_time_t *)
+ efi.systab->runtime->set_wakeup_time;
+ efi.get_variable = (efi_get_variable_t *)
+ efi.systab->runtime->get_variable;
+ efi.get_next_variable = (efi_get_next_variable_t *)
+ efi.systab->runtime->get_next_variable;
+ efi.set_variable = (efi_set_variable_t *)
+ efi.systab->runtime->set_variable;
+ efi.get_next_high_mono_count = (efi_get_next_high_mono_count_t *)
+ efi.systab->runtime->get_next_high_mono_count;
+ efi.reset_system = (efi_reset_system_t *)
+ efi.systab->runtime->reset_system;
+}
+
+void __init
+efi_initialize_iomem_resources(struct resource *code_resource,
+ struct resource *data_resource)
+{
+ struct resource *res;
+ efi_memory_desc_t *md;
+ int i;
+
+ for (i = 0; i < memmap.nr_map; i++) {
+ md = &memmap.map[i];
+
+ if ((md->phys_addr + (md->num_pages << EFI_PAGE_SHIFT)) >
+ 0x100000000ULL)
+ continue;
+ res = alloc_bootmem_low(sizeof(struct resource));
+ switch (md->type) {
+ case EFI_RESERVED_TYPE:
+ res->name = "Reserved Memory";
+ break;
+ case EFI_LOADER_CODE:
+ res->name = "Loader Code";
+ break;
+ case EFI_LOADER_DATA:
+ res->name = "Loader Data";
+ break;
+ case EFI_BOOT_SERVICES_DATA:
+ res->name = "BootServices Data";
+ break;
+ case EFI_BOOT_SERVICES_CODE:
+ res->name = "BootServices Code";
+ break;
+ case EFI_RUNTIME_SERVICES_CODE:
+ res->name = "Runtime Service Code";
+ break;
+ case EFI_RUNTIME_SERVICES_DATA:
+ res->name = "Runtime Service Data";
+ break;
+ case EFI_CONVENTIONAL_MEMORY:
+ res->name = "Conventional Memory";
+ break;
+ case EFI_UNUSABLE_MEMORY:
+ res->name = "Unusable Memory";
+ break;
+ case EFI_ACPI_RECLAIM_MEMORY:
+ res->name = "ACPI Reclaim";
+ break;
+ case EFI_ACPI_MEMORY_NVS:
+ res->name = "ACPI NVS";
+ break;
+ case EFI_MEMORY_MAPPED_IO:
+ res->name = "Memory Mapped IO";
+ break;
+ case EFI_MEMORY_MAPPED_IO_PORT_SPACE:
+ res->name = "Memory Mapped IO Port Space";
+ break;
+ default:
+ res->name = "Reserved";
+ break;
+ }
+ res->start = md->phys_addr;
+ res->end = res->start + ((md->num_pages << EFI_PAGE_SHIFT) - 1);
+ res->flags = IORESOURCE_MEM | IORESOURCE_BUSY;
+ if (request_resource(&iomem_resource, res) < 0)
+ printk(KERN_ERR PFX "Failed to allocate res %s : 0x%lx-0x%lx\n",
+ res->name, res->start, res->end);
+ /*
+ * We don't know which region contains kernel data so we try
+ * it repeatedly and let the resource manager test it.
+ */
+ if (md->type == EFI_CONVENTIONAL_MEMORY) {
+ request_resource(res, code_resource);
+ request_resource(res, data_resource);
+ }
+ }
+}
+
+/*
+ * Convenience functions to obtain memory types and attributes
+ */
+
+u32 efi_mem_type(unsigned long phys_addr)
+{
+ efi_memory_desc_t *md;
+ int i;
+
+ for (i = 0; i < memmap.nr_map; i++) {
+ md = &memmap.map[i];
+ if ((md->phys_addr <= phys_addr) && (phys_addr <
+ (md->phys_addr + (md-> num_pages << EFI_PAGE_SHIFT)) ))
+ return md->type;
+ }
+ return 0;
+}
+
+u64 efi_mem_attributes(unsigned long phys_addr)
+{
+ efi_memory_desc_t *md;
+ int i;
+
+ for (i = 0; i < memmap.nr_map; i++) {
+ md = &memmap.map[i];
+ if ((md->phys_addr <= phys_addr) && (phys_addr <
+ (md->phys_addr + (md-> num_pages << EFI_PAGE_SHIFT)) ))
+ return md->attribute;
+ }
+ return 0;
+}
+
diff -urN linux-2.6.0-test6-mm2/arch/i386/kernel/efi_stub.S linux-2.6.0-test6-mm2-efi/arch/i386/kernel/efi_stub.S
--- linux-2.6.0-test6-mm2/arch/i386/kernel/efi_stub.S 1969-12-31 16:00:00.000000000 -0800
+++ linux-2.6.0-test6-mm2-efi/arch/i386/kernel/efi_stub.S 2003-10-03 10:10:40.000000000 -0700
@@ -0,0 +1,125 @@
+/*
+ * EFI call stub for IA32.
+ *
+ * This stub allows us to make EFI calls in physical mode with interrupts
+ * turned off.
+ */
+
+#include <linux/config.h>
+#include <linux/linkage.h>
+#include <asm/page.h>
+#include <asm/pgtable.h>
+
+/*
+ * efi_call_phys(void *, ...) is a function with variable parameters.
+ * All the callers of this function assure that all the parameters are 4-bytes.
+ */
+
+/*
+ * In gcc calling convention, EBX, ESP, EBP, ESI and EDI are all callee save.
+ * So we'd better save all of them at the beginning of this function and restore
+ * at the end no matter how many we use, because we can not assure EFI runtime
+ * service functions will comply with gcc calling convention, too.
+ */
+
+.text
+.section .text, "a"
+ENTRY(efi_call_phys)
+ /*
+ * 0. The function can only be called in Linux kernel. So CS has been
+ * set to 0x0010, DS and SS have been set to 0x0018. In EFI, I found
+ * the values of these registers are the same. And, the corresponding
+ * GDT entries are identical. So I will do nothing about segment reg
+ * and GDT, but change GDT base register in prelog and epilog.
+ */
+
+ /*
+ * 1. Now I am running with EIP = <physical address> + PAGE_OFFSET.
+ * But to make it smoothly switch from virtual mode to flat mode.
+ * The mapping of lower virtual memory has been created in prelog and
+ * epilog.
+ */
+ movl $1f, %edx
+ subl $__PAGE_OFFSET, %edx
+ jmp *%edx
+1:
+
+ /*
+ * 2. Now on the top of stack is the return
+ * address in the caller of efi_call_phys(), then parameter 1,
+ * parameter 2, ..., param n. To make things easy, we save the return
+ * address of efi_call_phys in a global variable.
+ */
+ popl %edx
+ movl %edx, saved_return_addr
+ /* get the function pointer into ECX*/
+ popl %ecx
+ movl %ecx, efi_rt_function_ptr
+ movl $2f, %edx
+ subl $__PAGE_OFFSET, %edx
+ pushl %edx
+
+ /*
+ * 3. Clear PG bit in %CR0.
+ */
+ movl %cr0, %edx
+ andl $0x7fffffff, %edx
+ movl %edx, %cr0
+ jmp 1f
+1:
+
+ /*
+ * 4. Adjust stack pointer.
+ */
+ subl $__PAGE_OFFSET, %esp
+
+ /*
+ * 5. Call the physical function.
+ */
+ jmp *%ecx
+
+2:
+ /*
+ * 6. After EFI runtime service returns, control will return to
+ * following instruction. We'd better readjust stack pointer first.
+ */
+ addl $__PAGE_OFFSET, %esp
+
+ /*
+ * 7. Restore PG bit
+ */
+ movl %cr0, %edx
+ orl $0x80000000, %edx
+ movl %edx, %cr0
+ jmp 1f
+1:
+ /*
+ * 8. Now restore the virtual mode from flat mode by
+ * adding EIP with PAGE_OFFSET.
+ */
+ movl $1f, %edx
+ jmp *%edx
+1:
+
+ /*
+ * 9. Balance the stack. And because EAX contain the return value,
+ * we'd better not clobber it.
+ */
+ leal efi_rt_function_ptr, %edx
+ movl (%edx), %ecx
+ pushl %ecx
+
+ /*
+ * 10. Push the saved return address onto the stack and return.
+ */
+ leal saved_return_addr, %edx
+ movl (%edx), %ecx
+ pushl %ecx
+ ret
+.previous
+
+.data
+saved_return_addr:
+ .long 0
+efi_rt_function_ptr:
+ .long 0
diff -urN linux-2.6.0-test6-mm2/arch/i386/kernel/Makefile linux-2.6.0-test6-mm2-efi/arch/i386/kernel/Makefile
--- linux-2.6.0-test6-mm2/arch/i386/kernel/Makefile 2003-10-03 11:50:44.000000000 -0700
+++ linux-2.6.0-test6-mm2-efi/arch/i386/kernel/Makefile 2003-10-03 10:10:40.000000000 -0700
@@ -7,7 +7,7 @@
obj-y := process.o semaphore.o signal.o entry.o traps.o irq.o vm86.o \
ptrace.o i8259.o ioport.o ldt.o setup.o time.o sys_i386.o \
pci-dma.o i386_ksyms.o i387.o dmi_scan.o bootflag.o \
- doublefault.o entry_trampoline.o
+ doublefault.o efi.o efi_stub.o entry_trampoline.o
obj-y += cpu/
obj-y += timers/
diff -urN linux-2.6.0-test6-mm2/arch/i386/kernel/reboot.c linux-2.6.0-test6-mm2-efi/arch/i386/kernel/reboot.c
--- linux-2.6.0-test6-mm2/arch/i386/kernel/reboot.c 2003-10-03 11:50:44.000000000 -0700
+++ linux-2.6.0-test6-mm2-efi/arch/i386/kernel/reboot.c 2003-10-03 10:10:40.000000000 -0700
@@ -7,6 +7,7 @@
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/mc146818rtc.h>
+#include <linux/efi.h>
#include <asm/uaccess.h>
#include <asm/apic.h>
#include "mach_reboot.h"
@@ -261,7 +262,12 @@
disable_IO_APIC();
#endif
- if(!reboot_thru_bios) {
+ if (!reboot_thru_bios) {
+ if (efi_enabled) {
+ efi.reset_system(EFI_RESET_COLD, EFI_SUCCESS, 0, 0);
+ __asm__ __volatile__("lidt %0": :"m" (no_idt));
+ __asm__ __volatile__("int3");
+ }
/* rebooting needs to touch the page at absolute addr 0 */
*((unsigned short *)__va(0x472)) = reboot_mode;
for (;;) {
@@ -271,6 +277,8 @@
__asm__ __volatile__("int3");
}
}
+ if (efi_enabled)
+ efi.reset_system(EFI_RESET_WARM, EFI_SUCCESS, 0, 0);
machine_real_restart(jump_to_bios, sizeof(jump_to_bios));
}
@@ -281,6 +289,8 @@
void machine_power_off(void)
{
+ if (efi_enabled)
+ efi.reset_system(EFI_RESET_SHUTDOWN, EFI_SUCCESS, 0, 0);
if (pm_power_off)
pm_power_off();
}
diff -urN linux-2.6.0-test6-mm2/arch/i386/kernel/setup.c linux-2.6.0-test6-mm2-efi/arch/i386/kernel/setup.c
--- linux-2.6.0-test6-mm2/arch/i386/kernel/setup.c 2003-10-03 11:50:44.000000000 -0700
+++ linux-2.6.0-test6-mm2-efi/arch/i386/kernel/setup.c 2003-10-03 11:36:22.000000000 -0700
@@ -36,6 +36,8 @@
#include <linux/root_dev.h>
#include <linux/highmem.h>
#include <linux/module.h>
+#include <linux/efi.h>
+#include <linux/init.h>
#include <video/edid.h>
#include <asm/e820.h>
#include <asm/mpspec.h>
@@ -56,6 +58,8 @@
* Machine setup..
*/
+int efi_enabled = 0;
+
/* cpu data as detected by the assembly code in head.S */
struct cpuinfo_x86 new_cpu_data __initdata = { 0, 0, 0, 0, -1, 1, 0, 0, -1 };
/* common cpu data for all cpus */
@@ -144,6 +148,20 @@
int i;
unsigned long long current_size = 0;
+ if (efi_enabled) {
+ for (i = 0; i < memmap.nr_map; i++) {
+ current_size = memmap.map[i].phys_addr +
+ (memmap.map[i].num_pages << 12);
+ if (memmap.map[i].type == EFI_CONVENTIONAL_MEMORY) {
+ if (current_size > size) {
+ memmap.map[i].num_pages -=
+ (((current_size-size) + PAGE_SIZE-1) >> PAGE_SHIFT);
+ memmap.nr_map = i + 1;
+ return;
+ }
+ }
+ }
+ }
for (i = 0; i < e820.nr_map; i++) {
if (e820.map[i].type == E820_RAM) {
current_size += e820.map[i].size;
@@ -158,17 +176,21 @@
static void __init add_memory_region(unsigned long long start,
unsigned long long size, int type)
{
- int x = e820.nr_map;
+ int x;
+
+ if (!efi_enabled) {
+ x = e820.nr_map;
- if (x == E820MAX) {
- printk(KERN_ERR "Ooops! Too many entries in the memory map!\n");
- return;
- }
+ if (x == E820MAX) {
+ printk(KERN_ERR "Ooops! Too many entries in the memory map!\n");
+ return;
+ }
- e820.map[x].addr = start;
- e820.map[x].size = size;
- e820.map[x].type = type;
- e820.nr_map++;
+ e820.map[x].addr = start;
+ e820.map[x].size = size;
+ e820.map[x].type = type;
+ e820.nr_map++;
+ }
} /* add_memory_region */
#define E820_DEBUG 1
@@ -445,7 +467,6 @@
static void __init setup_memory_region(void)
{
char *who = machine_specific_memory_setup();
-
printk(KERN_INFO "BIOS-provided physical RAM map:\n");
print_memory_map(who);
} /* setup_memory_region */
@@ -583,6 +604,23 @@
}
/*
+ * Callback for efi_memory_walk.
+ */
+static int __init
+efi_find_max_pfn(unsigned long start, unsigned long end, void *arg)
+{
+ unsigned long *max_pfn = arg, pfn;
+
+ if (start < end) {
+ pfn = PFN_UP(end -1);
+ if (pfn > *max_pfn)
+ *max_pfn = pfn;
+ }
+ return 0;
+}
+
+
+/*
* Find the highest page frame number we have available
*/
void __init find_max_pfn(void)
@@ -590,6 +628,11 @@
int i;
max_pfn = 0;
+ if (efi_enabled) {
+ efi_memmap_walk(efi_find_max_pfn, &max_pfn);
+ return;
+ }
+
for (i = 0; i < e820.nr_map; i++) {
unsigned long start, end;
/* RAM? */
@@ -664,6 +707,25 @@
}
#ifndef CONFIG_DISCONTIGMEM
+
+/*
+ * Free all available memory for boot time allocation. Used
+ * as a callback function by efi_memory_walk()
+ */
+
+static int __init
+free_available_memory(unsigned long start, unsigned long end, void *arg)
+{
+ /* check max_low_pfn */
+ if (start >= ((max_low_pfn + 1) << PAGE_SHIFT))
+ return 0;
+ if (end >= ((max_low_pfn + 1) << PAGE_SHIFT))
+ end = (max_low_pfn + 1) << PAGE_SHIFT;
+ if (start < end)
+ free_bootmem(start, end - start);
+
+ return 0;
+}
/*
* Register fully available low RAM pages with the bootmem allocator.
*/
@@ -671,6 +733,10 @@
{
int i;
+ if (efi_enabled) {
+ efi_memmap_walk(free_available_memory, NULL);
+ return;
+ }
for (i = 0; i < e820.nr_map; i++) {
unsigned long curr_pfn, last_pfn, size;
/*
@@ -798,11 +864,11 @@
* Request address space for all standard RAM and ROM resources
* and also for regions reported as reserved by the e820.
*/
-static void __init register_memory(unsigned long max_low_pfn)
+static void __init
+legacy_init_iomem_resources(struct resource *code_resource, struct resource *data_resource)
{
- unsigned long low_mem_size;
int i;
-
+
probe_roms();
for (i = 0; i < e820.nr_map; i++) {
struct resource *res;
@@ -825,11 +891,26 @@
* so we try it repeatedly and let the resource manager
* test it.
*/
- request_resource(res, &code_resource);
- request_resource(res, &data_resource);
+ request_resource(res, code_resource);
+ request_resource(res, data_resource);
}
}
+}
+/*
+ * Request address space for all standard resources
+ */
+static void __init register_memory(unsigned long max_low_pfn)
+{
+ unsigned long low_mem_size;
+ int i;
+
+ if (efi_enabled)
+ efi_initialize_iomem_resources(&code_resource, &data_resource);
+ else
+ legacy_init_iomem_resources(&code_resource, &data_resource);
+
+ /* EFI systems may still have VGA */
request_graphics_resource();
/* request I/O space for devices used on all i[345]86 PCs */
@@ -949,6 +1030,13 @@
__setup("noreplacement", noreplacement_setup);
+/*
+ * Determine if we were loaded by an EFI loader. If so, then we have also been
+ * passed the efi memmap, systab, etc., so we should use these data structures
+ * for initialization. Note, the efi init code path is determined by the
+ * global efi_enabled. This allows the same kernel image to be used on existing
+ * systems (with a traditional BIOS) as well as on EFI systems.
+ */
void __init setup_arch(char **cmdline_p)
{
unsigned long max_low_pfn;
@@ -957,6 +1045,12 @@
pre_setup_arch_hook();
early_cpu_init();
+ /* FIXME: This isn't an official loader_type right
+ * now but does currently work with elilo.
+ */
+ if ((LOADER_TYPE == 0x50) && EFI_SYSTAB)
+ efi_enabled = 1;
+
ROOT_DEV = old_decode_dev(ORIG_ROOT_DEV);
drive_info = DRIVE_INFO;
screen_info = SCREEN_INFO;
@@ -979,7 +1073,11 @@
rd_doload = ((RAMDISK_FLAGS & RAMDISK_LOAD_FLAG) != 0);
#endif
ARCH_SETUP
- setup_memory_region();
+ if (efi_enabled)
+ efi_init();
+ else
+ setup_memory_region();
+
copy_edd();
if (!MOUNT_ROOT_RDONLY)
@@ -1013,6 +1111,8 @@
#ifdef CONFIG_X86_GENERICARCH
generic_apic_probe(*cmdline_p);
#endif
+ if (efi_enabled)
+ efi_map_memmap();
/*
* Parse the ACPI tables for possible boot-time SMP configuration.
@@ -1028,7 +1128,8 @@
#ifdef CONFIG_VT
#if defined(CONFIG_VGA_CONSOLE)
- conswitchp = &vga_con;
+ if (!efi_enabled || (efi_mem_type(0xa0000) != EFI_CONVENTIONAL_MEMORY))
+ conswitchp = &vga_con;
#elif defined(CONFIG_DUMMY_CONSOLE)
conswitchp = &dummy_con;
#endif
diff -urN linux-2.6.0-test6-mm2/arch/i386/kernel/time.c linux-2.6.0-test6-mm2-efi/arch/i386/kernel/time.c
--- linux-2.6.0-test6-mm2/arch/i386/kernel/time.c 2003-09-27 17:50:20.000000000 -0700
+++ linux-2.6.0-test6-mm2-efi/arch/i386/kernel/time.c 2003-10-03 10:10:40.000000000 -0700
@@ -44,6 +44,7 @@
#include <linux/module.h>
#include <linux/sysdev.h>
#include <linux/bcd.h>
+#include <linux/efi.h>
#include <asm/io.h>
#include <asm/smp.h>
@@ -160,6 +161,37 @@
return retval;
}
+static int efi_set_rtc_mmss(unsigned long nowtime)
+{
+ int real_seconds, real_minutes;
+ unsigned long flags;
+ efi_status_t status;
+ efi_time_t eft;
+ efi_time_cap_t cap;
+
+ spin_lock_irqsave(&rtc_lock, flags);
+
+ status = efi.get_time(&eft, &cap);
+ if (status != EFI_SUCCESS)
+ panic("Ooops, efitime: can't read time!\n");
+ real_seconds = nowtime % 60;
+ real_minutes = nowtime / 60;
+
+ if (((abs(real_minutes - eft.minute) + 15)/30) & 1)
+ real_minutes += 30;
+ real_minutes %= 60;
+
+ eft.minute = real_minutes;
+ eft.second = real_seconds;
+
+ status = efi.set_time(&eft);
+ if (status != EFI_SUCCESS)
+ panic("Ooops: efitime: can't read time!\n");
+
+ spin_unlock_irqrestore(&rtc_lock, flags);
+ return 0;
+}
+
/* last time the cmos clock got updated */
static long last_rtc_update;
@@ -212,7 +244,7 @@
>= USEC_AFTER - ((unsigned) TICK_SIZE) / 2 &&
(xtime.tv_nsec / 1000)
<= USEC_BEFORE + ((unsigned) TICK_SIZE) / 2) {
- if (set_rtc_mmss(xtime.tv_sec) == 0)
+ if ((efi_enabled && (!efi_set_rtc_mmss(xtime.tv_sec) )) || (set_rtc_mmss(xtime.tv_sec) == 0))
last_rtc_update = xtime.tv_sec;
else
last_rtc_update = xtime.tv_sec - 600; /* do it again in 60 s */
@@ -277,6 +309,27 @@
set_kset_name("pit"),
};
+/*
+ * This is called before the RT mappings are in place, so we
+ * need to be able to get the time in physical mode.
+ */
+unsigned long efi_get_time(void)
+{
+ efi_status_t status;
+ unsigned long flags;
+ efi_time_t eft;
+ efi_time_cap_t cap;
+
+ spin_lock_irqsave(&rtc_lock, flags);
+ status = phys_efi_get_time(&eft, &cap);
+ if (status != EFI_SUCCESS)
+ printk("Oops: efitime: can't read time status: 0x%lx\n", status);
+
+ spin_unlock_irqrestore(&rtc_lock, flags);
+
+ return mktime(eft.year, eft.month, eft.day, eft.hour, eft.minute, eft.second);
+}
+
/* XXX this driverfs stuff should probably go elsewhere later -john */
static struct sys_device device_i8253 = {
.id = 0,
@@ -298,7 +351,10 @@
/* Duplicate of time_init() below, with hpet_enable part added */
void __init hpet_time_init(void)
{
- xtime.tv_sec = get_cmos_time();
+ if (efi_enabled)
+ xtime.tv_sec = efi_get_time();
+ else
+ xtime.tv_sec = get_cmos_time();
wall_to_monotonic.tv_sec = -xtime.tv_sec;
xtime.tv_nsec = (INITIAL_JIFFIES % HZ) * (NSEC_PER_SEC / HZ);
wall_to_monotonic.tv_nsec = -xtime.tv_nsec;
@@ -324,8 +380,10 @@
return;
}
#endif
-
- xtime.tv_sec = get_cmos_time();
+ if (efi_enabled)
+ xtime.tv_sec = efi_get_time();
+ else
+ xtime.tv_sec = get_cmos_time();
wall_to_monotonic.tv_sec = -xtime.tv_sec;
xtime.tv_nsec = (INITIAL_JIFFIES % HZ) * (NSEC_PER_SEC / HZ);
wall_to_monotonic.tv_nsec = -xtime.tv_nsec;
diff -urN linux-2.6.0-test6-mm2/arch/i386/mm/init.c linux-2.6.0-test6-mm2-efi/arch/i386/mm/init.c
--- linux-2.6.0-test6-mm2/arch/i386/mm/init.c 2003-10-03 11:50:44.000000000 -0700
+++ linux-2.6.0-test6-mm2-efi/arch/i386/mm/init.c 2003-10-03 10:10:40.000000000 -0700
@@ -25,6 +25,7 @@
#include <linux/bootmem.h>
#include <linux/slab.h>
#include <linux/proc_fs.h>
+#include <linux/efi.h>
#include <asm/processor.h>
#include <asm/system.h>
@@ -52,12 +53,30 @@
return 0;
}
+extern int is_available_memory(efi_memory_desc_t *);
+
static inline int page_is_ram(unsigned long pagenr)
{
int i;
+ unsigned long addr, end;
+
+ if (efi_enabled) {
+ efi_memory_desc_t *md;
+
+ for (i = 0; i < memmap.nr_map; i++) {
+ md = &memmap.map[i];
+ if (!is_available_memory(md))
+ continue;
+ addr = (md->phys_addr+PAGE_SIZE-1) >> PAGE_SHIFT;
+ end = (md->phys_addr + (md->num_pages << EFI_PAGE_SHIFT)) >> PAGE_SHIFT;
+
+ if ((pagenr >= addr) && (pagenr < end))
+ return 1;
+ }
+ return 0;
+ }
for (i = 0; i < e820.nr_map; i++) {
- unsigned long addr, end;
if (e820.map[i].type != E820_RAM) /* not usable memory */
continue;
diff -urN linux-2.6.0-test6-mm2/drivers/acpi/Kconfig linux-2.6.0-test6-mm2-efi/drivers/acpi/Kconfig
--- linux-2.6.0-test6-mm2/drivers/acpi/Kconfig 2003-10-03 11:50:45.000000000 -0700
+++ linux-2.6.0-test6-mm2-efi/drivers/acpi/Kconfig 2003-10-03 11:48:18.000000000 -0700
@@ -252,10 +252,16 @@
dump your ACPI DSDT table using /proc/acpi/dsdt.
config ACPI_EFI
- bool
+ bool "Obtain RSDP from EFI Configuration Table"
depends on ACPI_INTERPRETER
- depends on IA64
- default y
+ depends on IA64 || X86
+ default y
+ help
+ On EFI Systems the RSDP pointer is passed to the kernel via
+ the EFI Configuration Table. On Itanium systems this is
+ standard and required. For IA-32, systems that have
+ EFI firmware should leave this enabled. Platforms with
+ traditional legacy BIOS should disable this option.
config ACPI_RELAXED_AML
bool "Relaxed AML"
diff -urN linux-2.6.0-test6-mm2/drivers/acpi/osl.c linux-2.6.0-test6-mm2-efi/drivers/acpi/osl.c
--- linux-2.6.0-test6-mm2/drivers/acpi/osl.c 2003-09-27 17:50:48.000000000 -0700
+++ linux-2.6.0-test6-mm2-efi/drivers/acpi/osl.c 2003-10-03 10:10:40.000000000 -0700
@@ -43,7 +43,6 @@
#ifdef CONFIG_ACPI_EFI
#include <linux/efi.h>
-u64 efi_mem_attributes (u64 phys_addr);
#endif
diff -urN linux-2.6.0-test6-mm2/include/asm-i386/setup.h linux-2.6.0-test6-mm2-efi/include/asm-i386/setup.h
--- linux-2.6.0-test6-mm2/include/asm-i386/setup.h 2003-09-27 17:50:31.000000000 -0700
+++ linux-2.6.0-test6-mm2-efi/include/asm-i386/setup.h 2003-10-03 10:10:40.000000000 -0700
@@ -29,6 +29,11 @@
#define IST_INFO (*(struct ist_info *) (PARAM+0x60))
#define DRIVE_INFO (*(struct drive_info_struct *) (PARAM+0x80))
#define SYS_DESC_TABLE (*(struct sys_desc_table_struct*)(PARAM+0xa0))
+#define EFI_SYSTAB ((efi_system_table_t *) *((unsigned long *)(PARAM+0x1c4)))
+#define EFI_MEMDESC_SIZE (*((unsigned long *) (PARAM+0x1c8)))
+#define EFI_MEMDESC_VERSION (*((unsigned long *) (PARAM+0x1cc)))
+#define EFI_MEMMAP ((efi_memory_desc_t *) *((unsigned long *)(PARAM+0x1d0)))
+#define EFI_MEMMAP_SIZE (*((unsigned long *) (PARAM+0x1d4)))
#define MOUNT_ROOT_RDONLY (*(unsigned short *) (PARAM+0x1F2))
#define RAMDISK_FLAGS (*(unsigned short *) (PARAM+0x1F8))
#define VIDEO_MODE (*(unsigned short *) (PARAM+0x1FA))
diff -urN linux-2.6.0-test6-mm2/include/linux/efi.h linux-2.6.0-test6-mm2-efi/include/linux/efi.h
--- linux-2.6.0-test6-mm2/include/linux/efi.h 2003-09-27 17:51:03.000000000 -0700
+++ linux-2.6.0-test6-mm2-efi/include/linux/efi.h 2003-10-03 13:21:05.000000000 -0700
@@ -16,6 +16,8 @@
#include <linux/time.h>
#include <linux/types.h>
#include <linux/proc_fs.h>
+#include <linux/rtc.h>
+#include <linux/ioport.h>
#include <asm/page.h>
#include <asm/system.h>
@@ -89,6 +91,11 @@
#define EFI_PAGE_SHIFT 12
+/*
+ * For current x86 implementations of EFI, there is
+ * additional padding in the mem descriptors. This is not
+ * the case in ia64. Need to have this fixed in the f/w.
+ */
typedef struct {
u32 type;
u32 pad;
@@ -96,6 +103,9 @@
u64 virt_addr;
u64 num_pages;
u64 attribute;
+#if defined (__i386__)
+ u64 pad1;
+#endif
} efi_memory_desc_t;
typedef int efi_freemem_callback_t (unsigned long start, unsigned long end, void *arg);
@@ -132,6 +142,7 @@
*/
#define EFI_RESET_COLD 0
#define EFI_RESET_WARM 1
+#define EFI_RESET_SHUTDOWN 2
/*
* EFI Runtime Services table
@@ -169,6 +180,10 @@
typedef efi_status_t efi_get_next_high_mono_count_t (u32 *count);
typedef void efi_reset_system_t (int reset_type, efi_status_t status,
unsigned long data_size, efi_char16_t *data);
+typedef efi_status_t efi_set_virtual_address_map_t (unsigned long memory_map_size,
+ unsigned long descriptor_size,
+ u32 descriptor_version,
+ efi_memory_desc_t *virtual_map);
/*
* EFI Configuration Table and GUID definitions
@@ -194,6 +209,9 @@
#define HCDP_TABLE_GUID \
EFI_GUID( 0xf951938d, 0x620b, 0x42ef, 0x82, 0x79, 0xa8, 0x4b, 0x79, 0x61, 0x78, 0x98 )
+#define UGA_IO_PROTOCOL_GUID \
+ EFI_GUID( 0x61a4d49e, 0x6f68, 0x4f1b, 0xb9, 0x22, 0xa8, 0x6e, 0xed, 0xb, 0x7, 0xa2 )
+
typedef struct {
efi_guid_t guid;
unsigned long table;
@@ -218,6 +236,13 @@
unsigned long tables;
} efi_system_table_t;
+struct efi_memory_map {
+ efi_memory_desc_t *phys_map;
+ efi_memory_desc_t *map;
+ int nr_map;
+ unsigned long desc_version;
+};
+
/*
* All runtime access to EFI goes through this structure:
*/
@@ -230,6 +255,7 @@
void *sal_systab; /* SAL system table */
void *boot_info; /* boot info table */
void *hcdp; /* HCDP table */
+ void *uga; /* UGA table */
efi_get_time_t *get_time;
efi_set_time_t *set_time;
efi_get_wakeup_time_t *get_wakeup_time;
@@ -239,6 +265,7 @@
efi_set_variable_t *set_variable;
efi_get_next_high_mono_count_t *get_next_high_mono_count;
efi_reset_system_t *reset_system;
+ efi_set_virtual_address_map_t *set_virtual_address_map;
} efi;
static inline int
@@ -260,12 +287,20 @@
extern void efi_init (void);
extern void efi_map_pal_code (void);
+extern void efi_map_memmap(void);
extern void efi_memmap_walk (efi_freemem_callback_t callback, void *arg);
extern void efi_gettimeofday (struct timespec *ts);
extern void efi_enter_virtual_mode (void); /* switch EFI to virtual mode, if possible */
extern u64 efi_get_iobase (void);
extern u32 efi_mem_type (unsigned long phys_addr);
extern u64 efi_mem_attributes (unsigned long phys_addr);
+extern void efi_initialize_iomem_resources(struct resource *code_resource,
+ struct resource *data_resource);
+extern efi_status_t phys_efi_get_time(efi_time_t *tm, efi_time_cap_t *tc);
+extern struct efi_memory_map memmap;
+extern int efi_enabled;
/*
* Variable Attributes
diff -urN linux-2.6.0-test6-mm2/init/main.c linux-2.6.0-test6-mm2-efi/init/main.c
--- linux-2.6.0-test6-mm2/init/main.c 2003-09-27 17:50:10.000000000 -0700
+++ linux-2.6.0-test6-mm2-efi/init/main.c 2003-10-03 10:10:40.000000000 -0700
@@ -37,6 +37,7 @@
#include <linux/moduleparam.h>
#include <linux/writeback.h>
#include <linux/cpu.h>
+#include <linux/efi.h>
#include <asm/io.h>
#include <asm/bugs.h>
@@ -436,6 +437,8 @@
pidmap_init();
pgtable_cache_init();
pte_chain_init();
+ if (efi_enabled)
+ efi_enter_virtual_mode();
fork_init(num_physpages);
proc_caches_init();
buffer_init();
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [updated patch] for efi support in ia32 kernels
2003-10-03 21:46 [updated patch] for efi support in ia32 kernels Tolentino, Matthew E
@ 2003-10-04 6:00 ` Andrew Morton
2003-10-04 6:55 ` Andrew Morton
1 sibling, 0 replies; 3+ messages in thread
From: Andrew Morton @ 2003-10-04 6:00 UTC (permalink / raw)
To: Tolentino, Matthew E; +Cc: ebiederm, linux-kernel
"Tolentino, Matthew E" <matthew.e.tolentino@intel.com> wrote:
>
> Attached is another patch that enables EFI boot-up support in ia32 kernels.
I've added the below patch to fix a few warnings:
arch/i386/kernel/efi.c:446: warning: cast from pointer to integer of different size
arch/i386/kernel/efi.c:455: warning: cast from pointer to integer of different size
arch/i386/kernel/efi.c:455: warning: cast to pointer from integer of different size
Please review, and test 2.6.0-test6-mm3 or later to make sure that things
are all OK.
Also, we really should make the EFI code CONFIGurable - it's another seven
kilobytes which a lot of people won't be needing. A patch against -mm
which implements that would be appreciated.
arch/i386/kernel/efi.c | 13 +++++++------
1 files changed, 7 insertions(+), 6 deletions(-)
diff -puN arch/i386/kernel/efi.c~ia32-efi-support-warning-fixes arch/i386/kernel/efi.c
--- 25/arch/i386/kernel/efi.c~ia32-efi-support-warning-fixes 2003-10-03 22:43:42.000000000 -0700
+++ 25-akpm/arch/i386/kernel/efi.c 2003-10-03 22:51:03.000000000 -0700
@@ -441,18 +441,19 @@ void __init efi_enter_virtual_mode(void)
if (md->attribute & EFI_MEMORY_RUNTIME) {
md->virt_addr =
- (u64) ioremap((unsigned long) md->phys_addr,
- (unsigned long) (md->num_pages
- << EFI_PAGE_SHIFT));
+ (unsigned long)ioremap(md->phys_addr,
+ md->num_pages << EFI_PAGE_SHIFT);
if (!(unsigned long) md->virt_addr) {
printk(KERN_ERR PFX "ioremap of md: 0x%lX failed \n",
(unsigned long) md->phys_addr);
}
if (((unsigned long)md->phys_addr <= (unsigned long)efi_phys.systab) && ((unsigned long)efi_phys.systab < md->phys_addr + ((unsigned long) md->num_pages << EFI_PAGE_SHIFT))) {
- efi.systab = (efi_system_table_t *)
- ((md->virt_addr - md->phys_addr) +
- (u64)efi_phys.systab);
+ unsigned long addr;
+
+ addr = md->virt_addr - md->phys_addr +
+ (unsigned long)efi_phys.systab;
+ efi.systab = (efi_system_table_t *)addr;
}
}
}
_
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [updated patch] for efi support in ia32 kernels
2003-10-03 21:46 [updated patch] for efi support in ia32 kernels Tolentino, Matthew E
2003-10-04 6:00 ` Andrew Morton
@ 2003-10-04 6:55 ` Andrew Morton
1 sibling, 0 replies; 3+ messages in thread
From: Andrew Morton @ 2003-10-04 6:55 UTC (permalink / raw)
To: Tolentino, Matthew E; +Cc: ebiederm, linux-kernel
"Tolentino, Matthew E" <matthew.e.tolentino@intel.com> wrote:
>
> Attached is another patch that enables EFI boot-up support in ia32 kernels.
When I enable CONFIG_ACPI_EFI on a fairly vanilla PC, the ethernet card
fails to generate any interrupts. See below for the unpromising changes
which CONFIG_ACPI_EFI made to my dmesg output.
Yes, this needs to be fixed - EFI-capable kernels should run unaffected on
hardware with older BIOSes.
ACPI: Subsystem revision 20030918
-IOAPIC[0]: Set PCI routing entry (2-9 -> 0x71 -> IRQ 9 Mode:1 Active:0)
-ACPI: Interpreter enabled
-ACPI: Using IOAPIC for interrupt routing
-ACPI: PCI Root Bridge [PCI0] (00:00)
+ACPI: System description tables not found
+ ACPI-0084: *** Error: acpi_load_tables: Could not get RSDP, AE_NOT_FOUND
+ ACPI-0134: *** Error: acpi_load_tables: Could not load tables: AE_NOT_FOUND
+ACPI: Unable to load the System Description Tables
+PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Transparent bridge - 0000:00:1e.0
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
-ACPI: Power Resource [FDDP] (off)
-ACPI: Power Resource [URP1] (off)
-ACPI: Power Resource [URP2] (off)
-ACPI: Power Resource [LPTP] (off)
-ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
-ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
-ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
-ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
-ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
-ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
-ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
-ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
-IOAPIC[0]: Set PCI routing entry (2-17 -> 0xa9 -> IRQ 17 Mode:1 Active:1)
-00:00:1f[B] -> 2-17 -> IRQ 17
-IOAPIC[0]: Set PCI routing entry (2-23 -> 0xb1 -> IRQ 23 Mode:1 Active:1)
-00:00:1f[C] -> 2-23 -> IRQ 23
-IOAPIC[0]: Set PCI routing entry (2-19 -> 0xb9 -> IRQ 19 Mode:1 Active:1)
-00:00:1f[D] -> 2-19 -> IRQ 19
-IOAPIC[0]: Set PCI routing entry (2-16 -> 0xc1 -> IRQ 16 Mode:1 Active:1)
-00:00:01[A] -> 2-16 -> IRQ 16
-Pin 2-17 already programmed
-IOAPIC[0]: Set PCI routing entry (2-21 -> 0xc9 -> IRQ 21 Mode:1 Active:1)
-00:02:09[A] -> 2-21 -> IRQ 21
-IOAPIC[0]: Set PCI routing entry (2-22 -> 0xd1 -> IRQ 22 Mode:1 Active:1)
-00:02:09[B] -> 2-22 -> IRQ 22
-Pin 2-23 already programmed
-Pin 2-17 already programmed
-Pin 2-22 already programmed
-Pin 2-23 already programmed
-Pin 2-17 already programmed
-Pin 2-21 already programmed
-Pin 2-23 already programmed
-Pin 2-17 already programmed
-Pin 2-21 already programmed
-Pin 2-22 already programmed
-Pin 2-17 already programmed
-Pin 2-21 already programmed
-Pin 2-22 already programmed
-Pin 2-23 already programmed
-Pin 2-21 already programmed
-Pin 2-22 already programmed
-Pin 2-23 already programmed
-Pin 2-17 already programmed
-Pin 2-22 already programmed
-Pin 2-23 already programmed
-Pin 2-17 already programmed
-Pin 2-21 already programmed
-Pin 2-17 already programmed
-IOAPIC[0]: Set PCI routing entry (2-20 -> 0xd9 -> IRQ 20 Mode:1 Active:1)
-00:02:08[A] -> 2-20 -> IRQ 20
-Pin 2-19 already programmed
-IOAPIC[0]: Set PCI routing entry (2-18 -> 0xe1 -> IRQ 18 Mode:1 Active:1)
-00:02:01[B] -> 2-18 -> IRQ 18
-Pin 2-23 already programmed
-PCI: Using ACPI for IRQ routing
-PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
+PCI: Using IRQ router PIIX [8086/2440] at 0000:00:1f.0
+PCI BIOS passed nonexistent PCI bus 0!
+PCI BIOS passed nonexistent PCI bus 0!
+PCI BIOS passed nonexistent PCI bus 0!
+PCI BIOS passed nonexistent PCI bus 1!
+PCI BIOS passed nonexistent PCI bus 0!
+PCI BIOS passed nonexistent PCI bus 2!
+PCI BIOS passed nonexistent PCI bus 0!
+PCI BIOS passed nonexistent PCI bus 2!
+PCI BIOS passed nonexistent PCI bus 0!
+PCI BIOS passed nonexistent PCI bus 2!
+PCI BIOS passed nonexistent PCI bus 0!
+PCI BIOS passed nonexistent PCI bus 2!
+PCI BIOS passed nonexistent PCI bus 0!
+PCI BIOS passed nonexistent PCI bus 2!
+PCI BIOS passed nonexistent PCI bus 0!
Machine check exception polling timer started.
Starting balanced_irq
Total HugeTLB memory allocated, 0
@@ -785,9 +744,6 @@
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
6355ac22e890d0a3c8481a5ca4825bc884d3e7a1ff98a2fc2ac7d8e064c3b2e6
pass
-ACPI: Power Button (FF) [PWRF]
-ACPI: Processor [CPU1] (supports C1)
-ACPI: Processor [CPU2] (supports C1)
pty: 256 Unix98 ptys configured
Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing disabled
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
@@ -830,11 +786,10 @@
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
-ACPI: (supports S0 S1 S4 S5)
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2003-10-04 6:54 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2003-10-03 21:46 [updated patch] for efi support in ia32 kernels Tolentino, Matthew E
2003-10-04 6:00 ` Andrew Morton
2003-10-04 6:55 ` Andrew Morton
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®