mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
* 2.6.15.4 ide-cd causes 'local unit communication failure' on NEC ND-4550A?
@ 2006-02-12 15:52 Matthias Andree
  2006-02-13 20:10 ` Matthias Andree
  0 siblings, 1 reply; 2+ messages in thread
From: Matthias Andree @ 2006-02-12 15:52 UTC (permalink / raw)
  To: axboe, linux-kernel

Greetings,

catchy subject, here's the story:

SUSE Linux kernels 2.6.13-15.7,
                   2.6.13-15.8 (both SUSE Linux 10.0 i586) and
Vanilla    kernel  2.6.15.4

cause "local unit communication failure" when running "readcd -c2scan"
on my NEC ND-4550A CD/DVD drive (VIA KT8237, Athlon XP 2500+, 1 GB RAM)
after at most two seconds of reading.

I am aware of three ways to trigger the problem currently:

1. as little as switching to a different tab in GNOME-Terminal.

2. hald-addon-storage's poll with CDROM_MEDIA_CHANGED and
   CDROM_DRIVE_STATUS ioctls cause the same problem (hald-addon-storage
   doesn't do anything else except opening and closing the device and
   sleeping for two seconds).

3. running two readcd -c2scan dev=/dev/hdc commands on the same drive
   triggers the problem, too.  One might argue this isn't very sensible,
   but it shouldn't confuse the drive either.

The problem is invariant to hdparm -d0 (or -d1) /dev/hdc, and hdparm -u0
or -u1 make no difference either.

A Plextor PX-W4824TA (/dev/hdd) on the same cable as the NEC works like
a charm, and with FreeBSD 6-STABLE, both work like a charm with (3.).
(This is a dualboot machine, so it's the very same hardware.)

readcd uses commands like these:

Executing 'read_cd' command on Bus 1 Target 0, Lun 0 timeout 40s
CDB:  BE 00 00 00 02 7D 00 00 31 FA 00 00
ioctl(3, SG_IO, 0xbfa5b2ac)             = 0

In a second run -- I needed to capture the output ;-) -- I get this:

CDB:  BE 00 00 00 00 31 00 00 31 FA 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 00 00 00 00 0A 00 00 00 00 08 00 00 00
Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x08 Qual 0x00 (logical unit communication failure) Fru 0x0
Sense flags: Blk 0 (not valid)
resid: 123748
cmd finished after 6.408s timeout 40s
readcd: Success. read_cd: scsi sendcmd: no error

I'd been using "sudo" to run this with ruid == euid == 0 to rule out
command filtering issues. I hope that was the right approach.

What else do you need to debug this? Is there some low-level debugging
output I could enable to see what the kernel sends and gets to/from the
drive?

Jörg Schilling suspected (on cdwrite(#)other,debian!org - typos are
mine) this might be a DMA problem (but what does he know of Linux...
little compared to his Solaris-fu), but I think we can rule that out,
the problem persists after hdparm -d0.  Jörg also insisted I tell him if
I had a 40 or 80 wire cable, _after_ I'd posted that FreeBSD worked OK
on the same hardware.

-- 
Matthias Andree

^ permalink raw reply	[flat|nested] 2+ messages in thread

end of thread, other threads:[~2006-02-13 20:10 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2006-02-12 15:52 2.6.15.4 ide-cd causes 'local unit communication failure' on NEC ND-4550A? Matthias Andree
2006-02-13 20:10 ` Matthias Andree

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®