* ACPI-related problem with resuming from RAM
@ 2006-07-30 9:40 Rafael J. Wysocki
2006-07-30 9:43 ` Rafael J. Wysocki
2006-07-30 9:52 ` Pavel Machek
0 siblings, 2 replies; 3+ messages in thread
From: Rafael J. Wysocki @ 2006-07-30 9:40 UTC (permalink / raw)
To: Linux ACPI; +Cc: LKML, Pavel Machek
Hi,
To make my box (Asus L5D, x86_64) resume from RAM, I have to unload all of the
ACPI-related modules and the ohci_hcd module before the suspend.
Also, I can't reload the ohci_hcd module after the resume, because if I try,
the system crashes with the appended trace.
Greetings,
Rafael
irq 11: nobody cared (try booting with the "irqpoll" option)
Call Trace:
[<ffffffff8020b145>] show_trace+0xa5/0x330
[<ffffffff8020b6b5>] dump_stack+0x15/0x20
[<ffffffff80263b48>] __report_bad_irq+0x38/0x90
[<ffffffff80263dca>] note_interrupt+0x22a/0x280
[<ffffffff80264a00>] handle_level_irq+0xf0/0x140
[<ffffffff8020ccdd>] do_IRQ+0x11d/0x140
[<ffffffff8020a23d>] ret_from_intr+0x0/0xf
DWARF2 unwinder stuck at ret_from_intr+0x0/0xf
Leftover inexact backtrace:
<IRQ> [<ffffffff8020ab82>] call_softirq+0x1e/0x28
[<ffffffff8023389a>] __do_softirq+0x5a/0xf0
[<ffffffff8020ab82>] call_softirq+0x1e/0x28
[<ffffffff8020cb4d>] do_softirq+0x3d/0xb0
[<ffffffff8023370e>] irq_exit+0x4e/0x60
[<ffffffff8020ccf5>] do_IRQ+0x135/0x140
[<ffffffff8020a23d>] ret_from_intr+0x0/0xf
<EOI><1>Unable to handle kernel paging request at ffffffff82800000 RIP:
[<ffffffff8020b362>] show_trace+0x2c2/0x330
PGD 203027 PUD 205027 PMD 0
Oops: 0000 [1] PREEMPT
last sysfs file: /devices/pci0000:00/0000:00:02.0/usb2/serial
CPU 0
Modules linked in: ohci_hcd ehci_hcd usbserial snd_pcm_oss snd_mixer_oss snd_seq snd_seq_device af_packet ip6t_REJECT xt_tcpudp bcm43xx ieee8
0211softmac pcmcia firmware_class ieee80211 ipt_REJECT ieee80211_crypt xt_state ohci1394 ieee1394 iptable_mangle iptable_nat ip_nat yenta_soc
ket iptable_filter rsrc_nonstatic pcmcia_core ip6table_mangle ip_conntrack ip_tables skge ip6table_filter ip6_tables x_tables snd_intel8x0 sn
d_ac97_codec snd_ac97_bus snd_pcm snd_timer snd soundcore snd_page_alloc i2c_nforce2 i2c_core parport_pc ipv6 lp parport dm_mod
Pid: 4908, comm: modprobe Tainted: G M 2.6.18-rc2-mm1 #20
RIP: 0010:[<ffffffff8020b362>] [<ffffffff8020b362>] show_trace+0x2c2/0x330
RSP: 0018:ffffffff8061ecb0 EFLAGS: 00010002
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000001
RBP: ffffffff8061ed90 R08: 0000000000000002 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff827ffffd
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
FS: 00002b41c0925b00(0000) GS:ffffffff808c0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffffffff82800000 CR3: 0000000056fc0000 CR4: 00000000000006e0
Process modprobe (pid: 4908, threadinfo ffff810056a46000, task ffff81005b88f040)
Stack: 0000000000000000 ffffffff880a6580 000000000000000a ffffffff8066a240
ffffffff8061eeb0 0000000000000022 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
Call Trace:
[<ffffffff8020b6b5>] dump_stack+0x15/0x20
[<ffffffff80263b48>] __report_bad_irq+0x38/0x90
[<ffffffff80263dca>] note_interrupt+0x22a/0x280
[<ffffffff80264a00>] handle_level_irq+0xf0/0x140
[<ffffffff8020ccdd>] do_IRQ+0x11d/0x140
[<ffffffff8020a23d>] ret_from_intr+0x0/0xf
DWARF2 unwinder stuck at ret_from_intr+0x0/0xf
Leftover inexact backtrace:
<IRQ> [<ffffffff8020ab82>] call_softirq+0x1e/0x28
[<ffffffff8023389a>] __do_softirq+0x5a/0xf0
[<ffffffff8020ab82>] call_softirq+0x1e/0x28
[<ffffffff8020cb4d>] do_softirq+0x3d/0xb0
[<ffffffff8023370e>] irq_exit+0x4e/0x60
[<ffffffff8020ccf5>] do_IRQ+0x135/0x140
[<ffffffff8020a23d>] ret_from_intr+0x0/0xf
<EOI><1>Unable to handle kernel paging request at ffffffff82800000 RIP:
[<ffffffff8020b362>] show_trace+0x2c2/0x330
PGD 203027 PUD 205027 PMD 0
Oops: 0000 [2] PREEMPT
last sysfs file: /devices/pci0000:00/0000:00:02.0/usb2/serial
CPU 0
Modules linked in: ohci_hcd ehci_hcd usbserial snd_pcm_oss snd_mixer_oss snd_seq snd_seq_device af_packet ip6t_REJECT xt_tcpudp bcm43xx ieee8
0211softmac pcmcia firmware_class ieee80211 ipt_REJECT ieee80211_crypt xt_state ohci1394 ieee1394 iptable_mangle iptable_nat ip_nat yenta_soc
ket iptable_filter rsrc_nonstatic pcmcia_core ip6table_mangle ip_conntrack ip_tables skge ip6table_filter ip6_tables x_tables snd_intel8x0 sn
d_ac97_codec snd_ac97_bus snd_pcm snd_timer snd soundcore snd_page_alloc i2c_nforce2 i2c_core parport_pc ipv6 lp parport dm_mod
Pid: 4908, comm: modprobe Tainted: G M 2.6.18-rc2-mm1 #20
RIP: 0010:[<ffffffff8020b362>] [<ffffffff8020b362>] show_trace+0x2c2/0x330
RSP: 0018:ffffffff8061e958 EFLAGS: 00010002
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000001
RBP: ffffffff8061ea38 R08: 0000000000000002 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff827ffffd
R13: 0000000000000000 R14: ffffffff8061ec08 R15: 0000000000000000
FS: 00002b41c0925b00(0000) GS:ffffffff808c0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffffffff82800000 CR3: 0000000056fc0000 CR4: 00000000000006e0
Process modprobe (pid: 4908, threadinfo ffff810056a46000, task ffff81005b88f040)
Stack: 0000000000000000 ffffffff880a6580 000000000000000a ffffffff8066a240
ffffffff8061eeb0 0000000000000022 0000000000000000 0000000000000000
0000000000000001 0000000000000002 0000000000000000 0000000000000000
Call Trace:
[<ffffffff8020b4be>] _show_stack+0xee/0x100
[<ffffffff8020b55a>] show_registers+0x8a/0x110
[<ffffffff8020b75f>] __die+0x9f/0xf0
[<ffffffff8021db61>] do_page_fault+0x7c1/0x8f0
[<ffffffff8020a659>] error_exit+0x0/0x96
DWARF2 unwinder stuck at error_exit+0x0/0x96
Leftover inexact backtrace:
<IRQ> [<ffffffff8020b362>] show_trace+0x2c2/0x330
[<ffffffff8020a23d>] ret_from_intr+0x0/0xf
[<ffffffff8020b6b5>] dump_stack+0x15/0x20
[<ffffffff80263b48>] __report_bad_irq+0x38/0x90
[<ffffffff80263dca>] note_interrupt+0x22a/0x280
[<ffffffff80262c28>] handle_IRQ_event+0x58/0x70
[<ffffffff80264a00>] handle_level_irq+0xf0/0x140
[<ffffffff8020ccdd>] do_IRQ+0x11d/0x140
[<ffffffff8020a23d>] ret_from_intr+0x0/0xf
[<ffffffff8020ab82>] call_softirq+0x1e/0x28
[<ffffffff8023389a>] __do_softirq+0x5a/0xf0
[<ffffffff8020ab82>] call_softirq+0x1e/0x28
[<ffffffff8020cb4d>] do_softirq+0x3d/0xb0
[<ffffffff8023370e>] irq_exit+0x4e/0x60
[<ffffffff8020ccf5>] do_IRQ+0x135/0x140
[<ffffffff8020a23d>] ret_from_intr+0x0/0xf
<EOI><1>Unable to handle kernel paging request at ffffffff82800000 RIP:
[<ffffffff8020b362>] show_trace+0x2c2/0x330
PGD 203027 PUD 205027 PMD 0
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: ACPI-related problem with resuming from RAM
2006-07-30 9:40 ACPI-related problem with resuming from RAM Rafael J. Wysocki
@ 2006-07-30 9:43 ` Rafael J. Wysocki
2006-07-30 9:52 ` Pavel Machek
1 sibling, 0 replies; 3+ messages in thread
From: Rafael J. Wysocki @ 2006-07-30 9:43 UTC (permalink / raw)
To: Linux ACPI; +Cc: LKML, Pavel Machek
On Sunday 30 July 2006 11:40, Rafael J. Wysocki wrote:
> Hi,
>
> To make my box (Asus L5D, x86_64) resume from RAM, I have to unload all of the
> ACPI-related modules and the ohci_hcd module before the suspend.
>
> Also, I can't reload the ohci_hcd module after the resume, because if I try,
> the system crashes with the appended trace.
The kernel is 2.6.18-rc2-mm1.
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: ACPI-related problem with resuming from RAM
2006-07-30 9:40 ACPI-related problem with resuming from RAM Rafael J. Wysocki
2006-07-30 9:43 ` Rafael J. Wysocki
@ 2006-07-30 9:52 ` Pavel Machek
1 sibling, 0 replies; 3+ messages in thread
From: Pavel Machek @ 2006-07-30 9:52 UTC (permalink / raw)
To: Rafael J. Wysocki; +Cc: Linux ACPI, LKML
Hi!
> To make my box (Asus L5D, x86_64) resume from RAM, I have to unload all of the
> ACPI-related modules and the ohci_hcd module before the suspend.
>
> Also, I can't reload the ohci_hcd module after the resume, because if I try,
> the system crashes with the appended trace.
> irq 11: nobody cared (try booting with the "irqpoll" option)
Heh, does it work with irqpoll? :-).
> Pid: 4908, comm: modprobe Tainted: G M 2.6.18-rc2-mm1 #20
What is "tainted: M"?
Strange, it seems that "screaming interrupt" detection went crazy and
dump_stack() caused it to oops? Can you stub-out show_trace and see
what happens?
> RIP: 0010:[<ffffffff8020b362>] [<ffffffff8020b362>] show_trace+0x2c2/0x330
> RSP: 0018:ffffffff8061ecb0 EFLAGS: 00010002
> RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
> RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000001
> RBP: ffffffff8061ed90 R08: 0000000000000002 R09: 0000000000000001
> R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff827ffffd
> R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
> FS: 00002b41c0925b00(0000) GS:ffffffff808c0000(0000) knlGS:0000000000000000
> CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
> CR2: ffffffff82800000 CR3: 0000000056fc0000 CR4: 00000000000006e0
> Process modprobe (pid: 4908, threadinfo ffff810056a46000, task ffff81005b88f040)
> Stack: 0000000000000000 ffffffff880a6580 000000000000000a ffffffff8066a240
> ffffffff8061eeb0 0000000000000022 0000000000000000 0000000000000000
> 0000000000000000 0000000000000000 0000000000000000 0000000000000000
> Call Trace:
> [<ffffffff8020b6b5>] dump_stack+0x15/0x20
> [<ffffffff80263b48>] __report_bad_irq+0x38/0x90
> [<ffffffff80263dca>] note_interrupt+0x22a/0x280
> [<ffffffff80264a00>] handle_level_irq+0xf0/0x140
> [<ffffffff8020ccdd>] do_IRQ+0x11d/0x140
> [<ffffffff8020a23d>] ret_from_intr+0x0/0xf
> DWARF2 unwinder stuck at ret_from_intr+0x0/0xf
> Leftover inexact backtrace:
> <IRQ> [<ffffffff8020ab82>] call_softirq+0x1e/0x28
> [<ffffffff8023389a>] __do_softirq+0x5a/0xf0
> [<ffffffff8020ab82>] call_softirq+0x1e/0x28
> [<ffffffff8020cb4d>] do_softirq+0x3d/0xb0
> [<ffffffff8023370e>] irq_exit+0x4e/0x60
> [<ffffffff8020ccf5>] do_IRQ+0x135/0x140
> [<ffffffff8020a23d>] ret_from_intr+0x0/0xf
> <EOI><1>Unable to handle kernel paging request at ffffffff82800000 RIP:
> [<ffffffff8020b362>] show_trace+0x2c2/0x330
> PGD 203027 PUD 205027 PMD 0
> Oops: 0000 [2] PREEMPT
> last sysfs file: /devices/pci0000:00/0000:00:02.0/usb2/serial
> CPU 0
Pavel
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2006-07-30 9:52 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2006-07-30 9:40 ACPI-related problem with resuming from RAM Rafael J. Wysocki
2006-07-30 9:43 ` Rafael J. Wysocki
2006-07-30 9:52 ` Pavel Machek
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome