* [r8169] Any success with RTL8110SC? @ 2007-02-22 19:17 Tom Burns 2007-02-22 22:31 ` Francois Romieu 0 siblings, 1 reply; 4+ messages in thread From: Tom Burns @ 2007-02-22 19:17 UTC (permalink / raw) To: linux-kernel Hi list, Does anyone have the Realtek gigabit RTL8110SC working? From reading the list it appears that support has been added to the r8169 in-kernel module. I can't get it to work - unfortunately I'm forced to use kernel 2.6.15-1 from Fedora Core 5 at the moment but I've tried: -backporting 2.6.18 to 2.6.20.1 versions of the module to work on 2.6.15-1 - it was trivial changes aside from 2.6.20.1 which required changes to the task scheduling code, but I'm pretty certain I didn't break anything. -applying the patch originally provided in http://www.uwsg.iu.edu/hypermail/linux/kernel/0702.0/0422.html to the 2.6.15-1 driver, or the 2.6.19.2 driver. -using the r1000 v1.05 driver available from the realtek website. The backported kernel modules successfully identify the rtl8110sc device and provide the eth interface, but do not successfully send/receive any packets on the wire. The r1000 driver seems to be able to send data on the wire for about a minute, receive packets back about 5% of the time, and after a minute stop working altogether, complaining that the "send buffer is full." Does anyone have this chipset working? Cheers, Tom Burns ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [r8169] Any success with RTL8110SC? 2007-02-22 19:17 [r8169] Any success with RTL8110SC? Tom Burns @ 2007-02-22 22:31 ` Francois Romieu 2007-02-23 16:41 ` Tom Burns 0 siblings, 1 reply; 4+ messages in thread From: Francois Romieu @ 2007-02-22 22:31 UTC (permalink / raw) To: Tom Burns; +Cc: linux-kernel Tom Burns <tom.i.burns@gmail.com> : [...] > 2.6.15-1 - it was trivial changes aside from 2.6.20.1 which required > changes to the task scheduling code, but I'm pretty certain I didn't > break anything. I do not have the answar that you expect but some information could help: - which motherboard is it ? - can you send a dmesg for 2.6.20.1 as well as a lspci -vvx from your computer ? [...] > The r1000 driver seems to be able to send data on the wire for about a > minute, receive packets back about 5% of the time, and after a minute > stop working altogether, complaining that the "send buffer is full." If I read you correctly, this version of the driver is less broken than the others, right ? If you are brave, you can try the patch below against 2.6.20-rc1: http://www.fr.zoreil.com/people/francois/misc/20070221-2.6.21-rc1-r8169-test.patch -- Ueimor ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [r8169] Any success with RTL8110SC? 2007-02-22 22:31 ` Francois Romieu @ 2007-02-23 16:41 ` Tom Burns 2007-02-26 15:55 ` Tom Burns 0 siblings, 1 reply; 4+ messages in thread From: Tom Burns @ 2007-02-23 16:41 UTC (permalink / raw) To: Francois Romieu; +Cc: linux-kernel Hi Francois, Thanks for your reply. On 2/22/07, Francois Romieu <romieu@fr.zoreil.com> wrote: [...] > I do not have the answar that you expect but some information could help: > - which motherboard is it ? > - can you send a dmesg for 2.6.20.1 as well as a lspci -vvx from your > computer ? The motherboard is the latest revision of the MB720F mini ITX: http://www.ibase-i.com.tw/mb720.htm I have attached my dmesg and lspci -vvx output at the bottom of the message. > > The r1000 driver seems to be able to send data on the wire for about a > > minute, receive packets back about 5% of the time, and after a minute > > stop working altogether, complaining that the "send buffer is full." > > If I read you correctly, this version of the driver is less broken than > the others, right ? Correct. On this board none of the versions of r8169 I backported to 2.6.15-1 were able to successfully put any data on the wire. The eth interface gets created, and the device does properly report the link status up/down (as shown at the bottom of the dmesg output below), but that's it afaik. The r1000 driver sends a bit of data as I had elaborated in the original email. > If you are brave, you can try the patch below against 2.6.20-rc1: > http://www.fr.zoreil.com/people/francois/misc/20070221-2.6.21-rc1-r8169-test.patch Thanks for providing that - however I just tried it, and I get the same results as with module I backported from 2.6.20 (that is, device is recognized but no data is sent on the wire). ===== output from lspci -vvx ===== 00:00.0 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge Subsystem: VIA Technologies, Inc. CN400/PM880 Host Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 8 Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M] Capabilities: [80] AGP version 3.5 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 59 02 06 00 30 22 00 00 00 06 00 08 80 00 10: 08 00 00 e8 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 59 02 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00:00.1 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00: 06 11 59 12 06 00 00 02 00 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:00.2 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00: 06 11 59 22 06 00 00 02 00 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:00.3 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00: 06 11 59 32 06 00 00 02 00 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:00.4 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00: 06 11 59 42 06 00 00 02 00 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:00.7 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00: 06 11 59 72 06 00 00 02 00 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: f4000000-f5ffffff Prefetchable memory behind bridge: f0000000-f3ffffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR+ <PERR+ BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 98 b1 07 01 30 02 00 00 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 20 e2 20: 00 f4 f0 f5 00 f0 f0 f3 00 00 00 00 00 00 00 00 30: 00 00 00 00 70 00 00 00 00 00 00 00 00 00 0a 00 00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Unknown device 8167 (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. Unknown device 8167 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (8000ns min, 16000ns max), Cache Line Size 08 Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at d000 [size=256] Region 1: Memory at f6023000 (32-bit, non-prefetchable) [size=256] [virtual] Expansion ROM at 10000000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable+ DSel=0 DScale=0 PME- 00: ec 10 67 81 07 00 b0 02 10 00 00 02 08 20 00 00 10: 01 d0 00 00 00 30 02 f6 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 ec 10 67 81 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 20 40 00:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) (prog-if 10 [OHCI]) Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (8000ns max), Cache Line Size 08 Interrupt: pin A routed to IRQ 10 Region 0: Memory at f6020000 (32-bit, non-prefetchable) [size=2K] Region 1: I/O ports at e600 [size=128] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 44 30 07 00 10 02 80 10 00 0c 08 20 00 00 10: 00 00 02 f6 01 e6 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 44 30 30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 20 00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Interrupt: pin B routed to IRQ 10 Region 0: I/O ports at ec00 [size=8] Region 1: I/O ports at ed00 [size=4] Region 2: I/O ports at ee00 [size=8] Region 3: I/O ports at e400 [size=4] Region 4: I/O ports at e500 [size=16] Region 5: I/O ports at d400 [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 49 31 07 00 90 02 80 8f 01 01 00 20 80 00 10: 01 ec 00 00 01 ed 00 00 01 ee 00 00 01 e4 00 00 20: 01 e5 00 00 01 d4 00 00 00 00 00 00 06 11 49 31 30: 00 00 00 00 c0 00 00 00 00 00 00 00 0a 02 00 00 00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Interrupt: pin A routed to IRQ 5 Region 4: I/O ports at e700 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 e7 00 00 00 00 00 00 00 00 00 00 06 11 71 05 30: 00 00 00 00 c0 00 00 00 00 00 00 00 05 01 00 00 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size 08 Interrupt: pin A routed to IRQ 5 Region 4: I/O ports at e800 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 e8 00 00 00 00 00 00 00 00 00 00 06 11 38 30 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 01 00 00 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size 08 Interrupt: pin A routed to IRQ 5 Region 4: I/O ports at e900 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 e9 00 00 00 00 00 00 00 00 00 00 06 11 38 30 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 01 00 00 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size 08 Interrupt: pin B routed to IRQ 10 Region 4: I/O ports at ea00 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 ea 00 00 00 00 00 00 00 00 00 00 06 11 38 30 30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00 00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size 08 Interrupt: pin B routed to IRQ 10 Region 4: I/O ports at eb00 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 eb 00 00 00 00 00 00 00 00 00 00 06 11 38 30 30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00 00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if 20 [EHCI]) Subsystem: VIA Technologies, Inc. USB 2.0 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size 08 Interrupt: pin C routed to IRQ 6 Region 0: Memory at f6021000 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 04 31 17 00 10 02 86 20 03 0c 08 20 80 00 10: 00 10 02 f6 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 04 31 30: 00 00 00 00 80 00 00 00 00 00 00 00 06 03 00 00 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South] Subsystem: VIA Technologies, Inc. DFI KT600-AL Motherboard Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 27 32 87 00 10 02 00 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 27 32 30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60) Subsystem: Avance Logic Inc. Unknown device 4760 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin C routed to IRQ 6 Region 0: I/O ports at d800 [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 59 30 01 00 10 02 60 00 01 04 00 00 00 00 10: 01 d8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 05 40 60 47 30: 00 00 00 00 c0 00 00 00 00 00 00 00 06 03 00 00 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78) Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller on VT8235 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (750ns min, 2000ns max), Cache Line Size 08 Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at e000 [size=256] Region 1: Memory at f6022000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 65 30 07 00 10 02 78 00 00 02 08 20 00 00 10: 01 e0 00 00 00 20 02 f6 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 02 01 30: 00 00 00 00 40 00 00 00 00 00 00 00 05 01 03 08 01:00.0 VGA compatible controller: VIA Technologies, Inc. S3 Unichrome Pro VGA Adapter (rev 02) (prog-if 00 [VGA]) Subsystem: VIA Technologies, Inc. S3 Unichrome Pro VGA Adapter Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min) Interrupt: pin A routed to IRQ 5 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M] Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at f5000000 [disabled] [size=64K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] AGP version 3.0 Status: RQ=256 Iso- ArqSz=0 Cal=7 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none> 00: 06 11 18 31 07 00 30 02 02 00 00 03 00 20 00 00 10: 08 00 00 f0 00 00 00 f4 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 18 31 30: 00 00 00 00 60 00 00 00 00 00 00 00 05 01 02 00 ===== end lspci -vvx ===== ===== output of dmesg with r8169.c module from 2.6.20 ===== Linux version 2.6.15-1.2054_FC5 (bhcompile@hs20-bc1-3.build.redhat.com) (gcc version 4.1.0 20060304 (Red Hat 4.1.0-3)) #1 Tue Mar 14 15:48:33 EST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000bdf0000 (usable) BIOS-e820: 000000000bdf0000 - 000000000bdf3000 (ACPI NVS) BIOS-e820: 000000000bdf3000 - 000000000be00000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 189MB LOWMEM available. Using x86 segment limits to approximate NX protection On node 0 totalpages: 48624 DMA zone: 4096 pages, LIFO batch:0 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 44528 pages, LIFO batch:7 HighMem zone: 0 pages, LIFO batch:0 DMI 2.3 present. Allocating PCI resources starting at 10000000 (gap: 0be00000:f2e00000) Built 1 zonelists Kernel command line: ro root=/dev/sda1 vga=785 noapic acpi=off No local APIC present or hardware disabled mapped APIC to ffffd000 (0117e000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 CPU 0 irqstacks, hard=c03d4000 soft=c03d3000 PID hash table entries: 1024 (order: 10, 16384 bytes) Detected 1399.535 MHz processor. Using tsc for high-res timesource Console: colour dummy device 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 187932k/194496k available (1914k kernel code, 6048k reserved, 774k data, 176k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 2805.00 BogoMIPS (lpj=5610006) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0381b83f 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line) CPU: L2 Cache: 64K (32 bytes/line) CPU: After all inits, caps: 0381b13f 00000000 00000000 00000000 00000000 000000dc 00000000 CPU: Centaur VIA Nehemiah stepping 0a Checking 'hlt' instruction... OK. checking if image is initramfs... it is Freeing initrd memory: 997k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xf9f20, last bus=1 PCI: Using configuration type 1 ACPI: Subsystem revision 20060127 ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI: disabled usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) Boot video device is 0000:01:00.0 PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0 PCI: Found IRQ 5 for device 0000:00:0f.1 PCI: Sharing IRQ 5 with 0000:00:10.0 PCI: Sharing IRQ 5 with 0000:00:10.1 PCI: Sharing IRQ 5 with 0000:00:12.0 PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: f4000000-f5ffffff PREFETCH window: f0000000-f3ffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) audit: initializing netlink socket (disabled) audit(1172277235.532:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API ksign: Installing public key data Loading keyring - Added public key EE596B44DDA71123 - User ID: Red Hat, Inc. (Kernel Module GPG key) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Bypassing VIA 8237 APIC De-Assert Message pci_hotplug: PCI Hot Plug PCI Core version: 0.5 vesafb: framebuffer at 0xf0000000, mapped to 0xcc880000, using 1200k, total 65536k vesafb: mode is 640x480x16, linelength=1280, pages=101 vesafb: protected mode interface info at c000:a585 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 80x30 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected VIA PM800/PN800/PM880/PN880 chipset agpgart: AGP aperture is 128M @ 0xe8000000 PNP: No PS/2 controller found. Probing ports directly. serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A serial8250: ttyS2 at I/O 0x3e8 (irq = 11) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 PCI: Found IRQ 5 for device 0000:00:0f.1 PCI: Sharing IRQ 5 with 0000:00:10.0 PCI: Sharing IRQ 5 with 0000:00:10.1 PCI: Sharing IRQ 5 with 0000:00:12.0 PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 5 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xe700-0xe707, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xe708-0xe70f, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... Probing IDE interface ide1... Probing IDE interface ide0... Probing IDE interface ide1... ide-floppy driver 0.99.newide usbcore: registered new driver libusual usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 NET: Registered protocol family 2 input: AT Translated Set 2 keyboard as /class/input/input0 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 5, 131072 bytes) TCP bind hash table entries: 8192 (order: 5, 163840 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode Freeing unused kernel memory: 176k freed Write protecting the kernel read-only data: 359k SCSI subsystem initialized input: PS2++ Logitech Wheel Mouse as /class/input/input1 libata version 1.20 loaded. sata_via 0000:00:0f.0: version 1.1 PCI: Found IRQ 10 for device 0000:00:0f.0 PCI: Sharing IRQ 10 with 0000:00:0a.0 PCI: Sharing IRQ 10 with 0000:00:10.2 PCI: Sharing IRQ 10 with 0000:00:10.3 sata_via 0000:00:0f.0: routed to hard irq line 10 ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xED02 bmdma 0xE500 irq 10 ata2: SATA max UDMA/133 cmd 0xEE00 ctl 0xE402 bmdma 0xE508 irq 10 ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 49:2f00 82:7469 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:407f ata1: dev 0 ATA-7, max UDMA/133, 156301488 sectors: LBA48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_via ata2: SATA link down (SStatus 0) scsi1 : sata_via Vendor: ATA Model: WDC WD800JD-22LS Rev: 06.0 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sd 0:0:0:0: Attached scsi disk sda kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: Disabled at runtime. SELinux: Unregistering netfilter hooks via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker PCI: Found IRQ 5 for device 0000:00:12.0 PCI: Sharing IRQ 5 with 0000:00:0f.1 PCI: Sharing IRQ 5 with 0000:00:10.0 PCI: Sharing IRQ 5 with 0000:00:10.1 eth0: VIA Rhine II at 0xf6022000, 00:03:2d:0a:c9:21, IRQ 5. eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link c5e1. PCI: Found IRQ 6 for device 0000:00:11.5 PCI: Sharing IRQ 6 with 0000:00:10.4 PCI: Setting latency timer of device 0000:00:11.5 to 64 USB Universal Host Controller Interface driver v2.3 PCI: Found IRQ 5 for device 0000:00:10.0 PCI: Sharing IRQ 5 with 0000:00:0f.1 PCI: Sharing IRQ 5 with 0000:00:10.1 PCI: Sharing IRQ 5 with 0000:00:12.0 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:10.0: irq 5, io base 0x0000e800 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected sd 0:0:0:0: Attached scsi generic sg0 type 0 PCI: Found IRQ 5 for device 0000:00:10.1 PCI: Sharing IRQ 5 with 0000:00:0f.1 PCI: Sharing IRQ 5 with 0000:00:10.0 PCI: Sharing IRQ 5 with 0000:00:12.0 uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.1: irq 5, io base 0x0000e900 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected PCI: Found IRQ 10 for device 0000:00:10.2 PCI: Sharing IRQ 10 with 0000:00:0a.0 PCI: Sharing IRQ 10 with 0000:00:0f.0 PCI: Sharing IRQ 10 with 0000:00:10.3 uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.2: irq 10, io base 0x0000ea00 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected PCI: Found IRQ 10 for device 0000:00:10.3 PCI: Sharing IRQ 10 with 0000:00:0a.0 PCI: Sharing IRQ 10 with 0000:00:0f.0 PCI: Sharing IRQ 10 with 0000:00:10.2 uhci_hcd 0000:00:10.3: UHCI Host Controller uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.3: irq 10, io base 0x0000eb00 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ieee1394: Initialized config rom entry `ip1394' PCI: Found IRQ 10 for device 0000:00:0c.0 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[f6020000-f60207ff] Max Packet=[2048] IR/IT contexts=[4/8] PCI: Found IRQ 6 for device 0000:00:10.4 PCI: Sharing IRQ 6 with 0000:00:11.5 ehci_hcd 0000:00:10.4: EHCI Host Controller ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:10.4: irq 6, io mem 0xf6021000 ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected Non-volatile memory driver v1.2 floppy0: Unable to grab IRQ6 for the floppy driver parport0: PC-style at 0x378 [PCSPP,TRISTATE] ieee1394: Host added: ID:BUS[0-00:1023] GUID[000000032d1122ad] lp0: using parport0 (polling). lp0: console ready md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com EXT3 FS on sda1, internal journal Adding 522104k swap on /dev/sda2. Priority:-1 extents:1 across:522104k eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1 r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded PCI: Found IRQ 10 for device 0000:00:0a.0 PCI: Sharing IRQ 10 with 0000:00:0f.0 PCI: Sharing IRQ 10 with 0000:00:10.2 PCI: Sharing IRQ 10 with 0000:00:10.3 eth1: RTL8169sc/8110sc at 0xccbca000, 00:03:2d:0a:c9:20, IRQ 10 r8169: eth1: link down eth0: link down r8169: eth1: link up Cheers, Tom ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [r8169] Any success with RTL8110SC? 2007-02-23 16:41 ` Tom Burns @ 2007-02-26 15:55 ` Tom Burns 0 siblings, 0 replies; 4+ messages in thread From: Tom Burns @ 2007-02-26 15:55 UTC (permalink / raw) To: Francois Romieu; +Cc: linux-kernel Hi again Francois, list, I've realized now that in reality, the r8169 driver (2.6.20-1 backported to 2.6.15-1, with the patch from Francois' first email applied) is receiving data! Just not transmitting any. tcpdump shows valid packets on the LAN, but ifconfig reports 0 packets transferred. Hope this helps. Cheers, Tom On 2/23/07, Tom Burns <tom.i.burns@gmail.com> wrote: > Hi Francois, > > Thanks for your reply. > > On 2/22/07, Francois Romieu <romieu@fr.zoreil.com> wrote: > [...] > > I do not have the answar that you expect but some information could help: > > - which motherboard is it ? > > - can you send a dmesg for 2.6.20.1 as well as a lspci -vvx from your > > computer ? > > The motherboard is the latest revision of the MB720F mini ITX: > http://www.ibase-i.com.tw/mb720.htm > > I have attached my dmesg and lspci -vvx output at the bottom of the message. > > > > The r1000 driver seems to be able to send data on the wire for about a > > > minute, receive packets back about 5% of the time, and after a minute > > > stop working altogether, complaining that the "send buffer is full." > > > > If I read you correctly, this version of the driver is less broken than > > the others, right ? > > Correct. On this board none of the versions of r8169 I backported to > 2.6.15-1 were able to successfully put any data on the wire. The eth > interface gets created, and the device does properly report the link > status up/down (as shown at the bottom of the dmesg output below), but > that's it afaik. The r1000 driver sends a bit of data as I had > elaborated in the original email. > > > If you are brave, you can try the patch below against 2.6.20-rc1: > > http://www.fr.zoreil.com/people/francois/misc/20070221-2.6.21-rc1-r8169-test.patch > > Thanks for providing that - however I just tried it, and I get the > same results as with module I backported from 2.6.20 (that is, device > is recognized but no data is sent on the wire). > > ===== output from lspci -vvx ===== > > 00:00.0 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge > Subsystem: VIA Technologies, Inc. CN400/PM880 Host Bridge > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort+ >SERR- <PERR- > Latency: 8 > Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M] > Capabilities: [80] AGP version 3.5 > Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- > FW+ AGP3+ Rate=x4,x8 > Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 59 02 06 00 30 22 00 00 00 06 00 08 80 00 > 10: 08 00 00 e8 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 59 02 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00 > > 00:00.1 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > 00: 06 11 59 12 06 00 00 02 00 00 00 06 00 00 00 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > 00:00.2 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > 00: 06 11 59 22 06 00 00 02 00 00 00 06 00 00 00 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > 00:00.3 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > 00: 06 11 59 32 06 00 00 02 00 00 00 06 00 00 00 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > 00:00.4 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > 00: 06 11 59 42 06 00 00 02 00 00 00 06 00 00 00 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > 00:00.7 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > 00: 06 11 59 72 06 00 00 02 00 00 00 06 00 00 00 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00 > > 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if > 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > Memory behind bridge: f4000000-f5ffffff > Prefetchable memory behind bridge: f0000000-f3ffffff > Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort+ <SERR+ <PERR+ > BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- > Capabilities: [70] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 98 b1 07 01 30 02 00 00 04 06 00 00 01 00 > 10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 20 e2 > 20: 00 f4 f0 f5 00 f0 f0 f3 00 00 00 00 00 00 00 00 > 30: 00 00 00 00 70 00 00 00 00 00 00 00 00 00 0a 00 > > 00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Unknown > device 8167 (rev 10) > Subsystem: Realtek Semiconductor Co., Ltd. Unknown device 8167 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (8000ns min, 16000ns max), Cache Line Size 08 > Interrupt: pin A routed to IRQ 10 > Region 0: I/O ports at d000 [size=256] > Region 1: Memory at f6023000 (32-bit, non-prefetchable) [size=256] > [virtual] Expansion ROM at 10000000 [disabled] [size=128K] > Capabilities: [dc] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable+ DSel=0 DScale=0 PME- > 00: ec 10 67 81 07 00 b0 02 10 00 00 02 08 20 00 00 > 10: 01 d0 00 00 00 30 02 f6 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 ec 10 67 81 > 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 20 40 > > 00:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host > Controller (rev 80) (prog-if 10 [OHCI]) > Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (8000ns max), Cache Line Size 08 > Interrupt: pin A routed to IRQ 10 > Region 0: Memory at f6020000 (32-bit, non-prefetchable) [size=2K] > Region 1: I/O ports at e600 [size=128] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 44 30 07 00 10 02 80 10 00 0c 08 20 00 00 > 10: 00 00 02 f6 01 e6 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 44 30 > 30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 20 > > 00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID > Controller (rev 80) (prog-if 8f [Master SecP SecO PriP PriO]) > Subsystem: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 > Interrupt: pin B routed to IRQ 10 > Region 0: I/O ports at ec00 [size=8] > Region 1: I/O ports at ed00 [size=4] > Region 2: I/O ports at ee00 [size=8] > Region 3: I/O ports at e400 [size=4] > Region 4: I/O ports at e500 [size=16] > Region 5: I/O ports at d400 [size=256] > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 49 31 07 00 90 02 80 8f 01 01 00 20 80 00 > 10: 01 ec 00 00 01 ed 00 00 01 ee 00 00 01 e4 00 00 > 20: 01 e5 00 00 01 d4 00 00 00 00 00 00 06 11 49 31 > 30: 00 00 00 00 c0 00 00 00 00 00 00 00 0a 02 00 00 > > 00:0f.1 IDE interface: VIA Technologies, Inc. > VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) > (prog-if 8a [Master SecP PriP]) > Subsystem: VIA Technologies, Inc. > VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 > Interrupt: pin A routed to IRQ 5 > Region 4: I/O ports at e700 [size=16] > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 01 e7 00 00 00 00 00 00 00 00 00 00 06 11 71 05 > 30: 00 00 00 00 c0 00 00 00 00 00 00 00 05 01 00 00 > > 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller (rev 81) (prog-if 00 [UHCI]) > Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32, Cache Line Size 08 > Interrupt: pin A routed to IRQ 5 > Region 4: I/O ports at e800 [size=32] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 01 e8 00 00 00 00 00 00 00 00 00 00 06 11 38 30 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 01 00 00 > > 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller (rev 81) (prog-if 00 [UHCI]) > Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32, Cache Line Size 08 > Interrupt: pin A routed to IRQ 5 > Region 4: I/O ports at e900 [size=32] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 01 e9 00 00 00 00 00 00 00 00 00 00 06 11 38 30 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 01 00 00 > > 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller (rev 81) (prog-if 00 [UHCI]) > Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32, Cache Line Size 08 > Interrupt: pin B routed to IRQ 10 > Region 4: I/O ports at ea00 [size=32] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 01 ea 00 00 00 00 00 00 00 00 00 00 06 11 38 30 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00 > > 00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller (rev 81) (prog-if 00 [UHCI]) > Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32, Cache Line Size 08 > Interrupt: pin B routed to IRQ 10 > Region 4: I/O ports at eb00 [size=32] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 01 eb 00 00 00 00 00 00 00 00 00 00 06 11 38 30 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00 > > 00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) > (prog-if 20 [EHCI]) > Subsystem: VIA Technologies, Inc. USB 2.0 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32, Cache Line Size 08 > Interrupt: pin C routed to IRQ 6 > Region 0: Memory at f6021000 (32-bit, non-prefetchable) [size=256] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 04 31 17 00 10 02 86 20 03 0c 08 20 80 00 > 10: 00 10 02 f6 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 04 31 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 06 03 00 00 > > 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge > [KT600/K8T800/K8T890 South] > Subsystem: VIA Technologies, Inc. DFI KT600-AL Motherboard > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping+ SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 27 32 87 00 10 02 00 00 01 06 00 00 80 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 27 32 > 30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 > > 00:11.5 Multimedia audio controller: VIA Technologies, Inc. > VT8233/A/8235/8237 AC97 Audio Controller (rev 60) > Subsystem: Avance Logic Inc. Unknown device 4760 > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Interrupt: pin C routed to IRQ 6 > Region 0: I/O ports at d800 [size=256] > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 59 30 01 00 10 02 60 00 01 04 00 00 00 00 > 10: 01 d8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 05 40 60 47 > 30: 00 00 00 00 c0 00 00 00 00 00 00 00 06 03 00 00 > > 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78) > Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet > Controller on VT8235 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (750ns min, 2000ns max), Cache Line Size 08 > Interrupt: pin A routed to IRQ 5 > Region 0: I/O ports at e000 [size=256] > Region 1: Memory at f6022000 (32-bit, non-prefetchable) [size=256] > Capabilities: [40] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 65 30 07 00 10 02 78 00 00 02 08 20 00 00 > 10: 01 e0 00 00 00 20 02 f6 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 02 01 > 30: 00 00 00 00 40 00 00 00 00 00 00 00 05 01 03 08 > > 01:00.0 VGA compatible controller: VIA Technologies, Inc. S3 Unichrome > Pro VGA Adapter (rev 02) (prog-if 00 [VGA]) > Subsystem: VIA Technologies, Inc. S3 Unichrome Pro VGA Adapter > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (500ns min) > Interrupt: pin A routed to IRQ 5 > Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M] > Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=16M] > [virtual] Expansion ROM at f5000000 [disabled] [size=64K] > Capabilities: [60] Power Management version 2 > Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [70] AGP version 3.0 > Status: RQ=256 Iso- ArqSz=0 Cal=7 SBA+ ITACoh- GART64- HTrans- > 64bit- FW- AGP3+ Rate=x4,x8 > Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none> > 00: 06 11 18 31 07 00 30 02 02 00 00 03 00 20 00 00 > 10: 08 00 00 f0 00 00 00 f4 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 18 31 > 30: 00 00 00 00 60 00 00 00 00 00 00 00 05 01 02 00 > > ===== end lspci -vvx ===== > > ===== output of dmesg with r8169.c module from 2.6.20 ===== > > Linux version 2.6.15-1.2054_FC5 > (bhcompile@hs20-bc1-3.build.redhat.com) (gcc version 4.1.0 20060304 > (Red Hat 4.1.0-3)) #1 Tue Mar 14 15:48:33 EST 2006 > BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009f800 (usable) > BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 000000000bdf0000 (usable) > BIOS-e820: 000000000bdf0000 - 000000000bdf3000 (ACPI NVS) > BIOS-e820: 000000000bdf3000 - 000000000be00000 (ACPI data) > BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) > 0MB HIGHMEM available. > 189MB LOWMEM available. > Using x86 segment limits to approximate NX protection > On node 0 totalpages: 48624 > DMA zone: 4096 pages, LIFO batch:0 > DMA32 zone: 0 pages, LIFO batch:0 > Normal zone: 44528 pages, LIFO batch:7 > HighMem zone: 0 pages, LIFO batch:0 > DMI 2.3 present. > Allocating PCI resources starting at 10000000 (gap: 0be00000:f2e00000) > Built 1 zonelists > Kernel command line: ro root=/dev/sda1 vga=785 noapic acpi=off > No local APIC present or hardware disabled > mapped APIC to ffffd000 (0117e000) > Enabling fast FPU save and restore... done. > Enabling unmasked SIMD FPU exception support... done. > Initializing CPU#0 > CPU 0 irqstacks, hard=c03d4000 soft=c03d3000 > PID hash table entries: 1024 (order: 10, 16384 bytes) > Detected 1399.535 MHz processor. > Using tsc for high-res timesource > Console: colour dummy device 80x25 > Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) > Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) > Memory: 187932k/194496k available (1914k kernel code, 6048k reserved, > 774k data, 176k init, 0k highmem) > Checking if this processor honours the WP bit even in supervisor mode... Ok. > Calibrating delay using timer specific routine.. 2805.00 BogoMIPS (lpj=5610006) > Security Framework v1.0.0 initialized > SELinux: Initializing. > SELinux: Starting in permissive mode > selinux_register_security: Registering secondary module capability > Capability LSM initialized as secondary > Mount-cache hash table entries: 512 > CPU: After generic identify, caps: 0381b83f 00000000 00000000 00000000 > 00000000 00000000 00000000 > CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line) > CPU: L2 Cache: 64K (32 bytes/line) > CPU: After all inits, caps: 0381b13f 00000000 00000000 00000000 > 00000000 000000dc 00000000 > CPU: Centaur VIA Nehemiah stepping 0a > Checking 'hlt' instruction... OK. > checking if image is initramfs... it is > Freeing initrd memory: 997k freed > NET: Registered protocol family 16 > PCI: PCI BIOS revision 2.10 entry at 0xf9f20, last bus=1 > PCI: Using configuration type 1 > ACPI: Subsystem revision 20060127 > ACPI: Interpreter disabled. > Linux Plug and Play Support v0.97 (c) Adam Belay > pnp: PnP ACPI: disabled > usbcore: registered new driver usbfs > usbcore: registered new driver hub > PCI: Probing PCI hardware > PCI: Probing PCI hardware (bus 00) > Boot video device is 0000:01:00.0 > PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0 > PCI: Found IRQ 5 for device 0000:00:0f.1 > PCI: Sharing IRQ 5 with 0000:00:10.0 > PCI: Sharing IRQ 5 with 0000:00:10.1 > PCI: Sharing IRQ 5 with 0000:00:12.0 > PCI: Bridge: 0000:00:01.0 > IO window: disabled. > MEM window: f4000000-f5ffffff > PREFETCH window: f0000000-f3ffffff > PCI: Setting latency timer of device 0000:00:01.0 to 64 > apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) > audit: initializing netlink socket (disabled) > audit(1172277235.532:1): initialized > Total HugeTLB memory allocated, 0 > VFS: Disk quotas dquot_6.5.1 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > SELinux: Registering netfilter hooks > Initializing Cryptographic API > ksign: Installing public key data > Loading keyring > - Added public key EE596B44DDA71123 > - User ID: Red Hat, Inc. (Kernel Module GPG key) > io scheduler noop registered > io scheduler anticipatory registered > io scheduler deadline registered > io scheduler cfq registered (default) > PCI: Bypassing VIA 8237 APIC De-Assert Message > pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > vesafb: framebuffer at 0xf0000000, mapped to 0xcc880000, using 1200k, > total 65536k > vesafb: mode is 640x480x16, linelength=1280, pages=101 > vesafb: protected mode interface info at c000:a585 > vesafb: scrolling: redraw > vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 > Console: switching to colour frame buffer device 80x30 > fb0: VESA VGA frame buffer device > isapnp: Scanning for PnP cards... > isapnp: No Plug & Play device found > Real Time Clock Driver v1.12ac > Linux agpgart interface v0.101 (c) Dave Jones > agpgart: Detected VIA PM800/PN800/PM880/PN880 chipset > agpgart: AGP aperture is 128M @ 0xe8000000 > PNP: No PS/2 controller found. Probing ports directly. > serio: i8042 AUX port at 0x60,0x64 irq 12 > serio: i8042 KBD port at 0x60,0x64 irq 1 > Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled > serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A > serial8250: ttyS2 at I/O 0x3e8 (irq = 11) is a 16550A > RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > VP_IDE: IDE controller at PCI slot 0000:00:0f.1 > PCI: Found IRQ 5 for device 0000:00:0f.1 > PCI: Sharing IRQ 5 with 0000:00:10.0 > PCI: Sharing IRQ 5 with 0000:00:10.1 > PCI: Sharing IRQ 5 with 0000:00:12.0 > PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 5 > VP_IDE: chipset revision 6 > VP_IDE: not 100% native mode: will probe irqs later > VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 > ide0: BM-DMA at 0xe700-0xe707, BIOS settings: hda:pio, hdb:pio > ide1: BM-DMA at 0xe708-0xe70f, BIOS settings: hdc:pio, hdd:pio > Probing IDE interface ide0... > Probing IDE interface ide1... > Probing IDE interface ide0... > Probing IDE interface ide1... > ide-floppy driver 0.99.newide > usbcore: registered new driver libusual > usbcore: registered new driver hiddev > usbcore: registered new driver usbhid > drivers/usb/input/hid-core.c: v2.6:USB HID core driver > mice: PS/2 mouse device common for all mice > md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 > md: bitmap version 4.39 > NET: Registered protocol family 2 > input: AT Translated Set 2 keyboard as /class/input/input0 > IP route cache hash table entries: 2048 (order: 1, 8192 bytes) > TCP established hash table entries: 8192 (order: 5, 131072 bytes) > TCP bind hash table entries: 8192 (order: 5, 163840 bytes) > TCP: Hash tables configured (established 8192 bind 8192) > TCP reno registered > TCP bic registered > Initializing IPsec netlink socket > NET: Registered protocol family 1 > NET: Registered protocol family 17 > Using IPI Shortcut mode > Freeing unused kernel memory: 176k freed > Write protecting the kernel read-only data: 359k > SCSI subsystem initialized > input: PS2++ Logitech Wheel Mouse as /class/input/input1 > libata version 1.20 loaded. > sata_via 0000:00:0f.0: version 1.1 > PCI: Found IRQ 10 for device 0000:00:0f.0 > PCI: Sharing IRQ 10 with 0000:00:0a.0 > PCI: Sharing IRQ 10 with 0000:00:10.2 > PCI: Sharing IRQ 10 with 0000:00:10.3 > sata_via 0000:00:0f.0: routed to hard irq line 10 > ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xED02 bmdma 0xE500 irq 10 > ata2: SATA max UDMA/133 cmd 0xEE00 ctl 0xE402 bmdma 0xE508 irq 10 > ata1: SATA link up 1.5 Gbps (SStatus 113) > ata1: dev 0 cfg 49:2f00 82:7469 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:407f > ata1: dev 0 ATA-7, max UDMA/133, 156301488 sectors: LBA48 > ata1: dev 0 configured for UDMA/133 > scsi0 : sata_via > ata2: SATA link down (SStatus 0) > scsi1 : sata_via > Vendor: ATA Model: WDC WD800JD-22LS Rev: 06.0 > Type: Direct-Access ANSI SCSI revision: 05 > SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) > sda: Write Protect is off > sda: Mode Sense: 00 3a 00 00 > SCSI device sda: drive cache: write back > SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) > sda: Write Protect is off > sda: Mode Sense: 00 3a 00 00 > SCSI device sda: drive cache: write back > sda: sda1 sda2 > sd 0:0:0:0: Attached scsi disk sda > kjournald starting. Commit interval 5 seconds > EXT3-fs: mounted filesystem with ordered data mode. > SELinux: Disabled at runtime. > SELinux: Unregistering netfilter hooks > via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker > PCI: Found IRQ 5 for device 0000:00:12.0 > PCI: Sharing IRQ 5 with 0000:00:0f.1 > PCI: Sharing IRQ 5 with 0000:00:10.0 > PCI: Sharing IRQ 5 with 0000:00:10.1 > eth0: VIA Rhine II at 0xf6022000, 00:03:2d:0a:c9:21, IRQ 5. > eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link c5e1. > PCI: Found IRQ 6 for device 0000:00:11.5 > PCI: Sharing IRQ 6 with 0000:00:10.4 > PCI: Setting latency timer of device 0000:00:11.5 to 64 > USB Universal Host Controller Interface driver v2.3 > PCI: Found IRQ 5 for device 0000:00:10.0 > PCI: Sharing IRQ 5 with 0000:00:0f.1 > PCI: Sharing IRQ 5 with 0000:00:10.1 > PCI: Sharing IRQ 5 with 0000:00:12.0 > uhci_hcd 0000:00:10.0: UHCI Host Controller > uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 > uhci_hcd 0000:00:10.0: irq 5, io base 0x0000e800 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 2 ports detected > sd 0:0:0:0: Attached scsi generic sg0 type 0 > PCI: Found IRQ 5 for device 0000:00:10.1 > PCI: Sharing IRQ 5 with 0000:00:0f.1 > PCI: Sharing IRQ 5 with 0000:00:10.0 > PCI: Sharing IRQ 5 with 0000:00:12.0 > uhci_hcd 0000:00:10.1: UHCI Host Controller > uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 > uhci_hcd 0000:00:10.1: irq 5, io base 0x0000e900 > usb usb2: configuration #1 chosen from 1 choice > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 2 ports detected > PCI: Found IRQ 10 for device 0000:00:10.2 > PCI: Sharing IRQ 10 with 0000:00:0a.0 > PCI: Sharing IRQ 10 with 0000:00:0f.0 > PCI: Sharing IRQ 10 with 0000:00:10.3 > uhci_hcd 0000:00:10.2: UHCI Host Controller > uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 > uhci_hcd 0000:00:10.2: irq 10, io base 0x0000ea00 > usb usb3: configuration #1 chosen from 1 choice > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 2 ports detected > PCI: Found IRQ 10 for device 0000:00:10.3 > PCI: Sharing IRQ 10 with 0000:00:0a.0 > PCI: Sharing IRQ 10 with 0000:00:0f.0 > PCI: Sharing IRQ 10 with 0000:00:10.2 > uhci_hcd 0000:00:10.3: UHCI Host Controller > uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 > uhci_hcd 0000:00:10.3: irq 10, io base 0x0000eb00 > usb usb4: configuration #1 chosen from 1 choice > hub 4-0:1.0: USB hub found > hub 4-0:1.0: 2 ports detected > ieee1394: Initialized config rom entry `ip1394' > PCI: Found IRQ 10 for device 0000:00:0c.0 > ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] > MMIO=[f6020000-f60207ff] Max Packet=[2048] IR/IT contexts=[4/8] > PCI: Found IRQ 6 for device 0000:00:10.4 > PCI: Sharing IRQ 6 with 0000:00:11.5 > ehci_hcd 0000:00:10.4: EHCI Host Controller > ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 > ehci_hcd 0000:00:10.4: irq 6, io mem 0xf6021000 > ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 > usb usb5: configuration #1 chosen from 1 choice > hub 5-0:1.0: USB hub found > hub 5-0:1.0: 8 ports detected > Non-volatile memory driver v1.2 > floppy0: Unable to grab IRQ6 for the floppy driver > parport0: PC-style at 0x378 [PCSPP,TRISTATE] > ieee1394: Host added: ID:BUS[0-00:1023] GUID[000000032d1122ad] > lp0: using parport0 (polling). > lp0: console ready > md: Autodetecting RAID arrays. > md: autorun ... > md: ... autorun DONE. > device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com > EXT3 FS on sda1, internal journal > Adding 522104k swap on /dev/sda2. Priority:-1 extents:1 across:522104k > eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1 > r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded > PCI: Found IRQ 10 for device 0000:00:0a.0 > PCI: Sharing IRQ 10 with 0000:00:0f.0 > PCI: Sharing IRQ 10 with 0000:00:10.2 > PCI: Sharing IRQ 10 with 0000:00:10.3 > eth1: RTL8169sc/8110sc at 0xccbca000, 00:03:2d:0a:c9:20, IRQ 10 > r8169: eth1: link down > eth0: link down > r8169: eth1: link up > > Cheers, > Tom > ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2007-02-26 15:55 UTC | newest] Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2007-02-22 19:17 [r8169] Any success with RTL8110SC? Tom Burns 2007-02-22 22:31 ` Francois Romieu 2007-02-23 16:41 ` Tom Burns 2007-02-26 15:55 ` Tom Burns
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®