* difference between arcmsr (areca) 1.20.0X.13 & 2.6.20 in tree driver?
@ 2007-04-03 3:21 Joshua Hoblitt
2007-04-03 15:45 ` Randy Dunlap
0 siblings, 1 reply; 3+ messages in thread
From: Joshua Hoblitt @ 2007-04-03 3:21 UTC (permalink / raw)
To: linux-kernel
[-- Attachment #1: Type: text/plain, Size: 5304 bytes --]
Has anyone else noticed this regression?
-J
--
----- Forwarded message from Joshua Hoblitt <jhoblitt@ifa.hawaii.edu> -----
From: Joshua Hoblitt <jhoblitt@ifa.hawaii.edu>
Date: Thu, 29 Mar 2007 16:38:20 -1000
To: erich@areca.com.tw
Subject: difference between 1.20.0X.13 & 2.6.20 in tree driver?
Hello,
I just attempted to upgrade a system from 2.6.17 (gentoo revision 8) w/
1.20.0X.13 to 2.6.20 (gentoo revision 4) with the in tree arcmsr driver.
On the 2.6.17 kernel there are 2 ~4TB partitions that are visible on
the system as /dev/sdb1 & /dev/sdc1. When the system is booted with the
2.6.20 kernel /dev/sdc1 is gone and /dev/sdb1 is properly reported as a
4TB EFI partition but fsck rejects the the filesystem as corrupt. Is
this a regression or has there been a fundamental change in the way
arcmsr represents the array to the block layer?
Here is the info on the RAID card:
Controller Name ARC-1170
Firmware Version V1.39 2005-12-13
BOOT ROM Version V1.39 2005-12-13
Serial Number Y605CAAVAR700117
Unit Serial #
Main Processor 500MHz IOP331
CPU ICache Size 32KBytes
CPU DCache Size 32KBytes / Write Back
System Memory 256MB / 333MHz
Any idea as to what's going on?
Thanks,
-J
--
Under 2.6.20:
Mar 29 15:41:05 ipp000 ARECA RAID ADAPTER4: FIRMWARE VERSION V1.39 2005-12-13
Mar 29 15:41:05 ipp000 scsi4 : Areca SATA Host Adapter RAID Controller( RAID6 capable)
Mar 29 15:41:05 ipp000 Driver Version 1.20.00.13
Mar 29 15:41:05 ipp000 scsi 4:0:0:0: Direct-Access Areca ARC-1170-VOL#00 R001 PQ: 0 ANSI: 3
Mar 29 15:41:05 ipp000 sdb : very big device. try to use READ CAPACITY(16).
Mar 29 15:41:05 ipp000 SCSI device sdb: 8595693568 512-byte hdwr sectors (4400995 MB)
Mar 29 15:41:05 ipp000 sdb: Write Protect is off
Mar 29 15:41:05 ipp000 sdb: Mode Sense: cb 00 00 08
Mar 29 15:41:05 ipp000 SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 29 15:41:05 ipp000 sdb : very big device. try to use READ CAPACITY(16).
Mar 29 15:41:05 ipp000 SCSI device sdb: 8595693568 512-byte hdwr sectors (4400995 MB)
Mar 29 15:41:05 ipp000 sdb: Write Protect is off
Mar 29 15:41:05 ipp000 sdb: Mode Sense: cb 00 00 08
Mar 29 15:41:05 ipp000 SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 29 15:41:05 ipp000 sdb: sdb1
Mar 29 15:41:05 ipp000 sd 4:0:0:0: Attached scsi disk sdb
Mar 29 15:41:05 ipp000 scsi 4:0:16:0: Processor Areca RAID controller R001 PQ: 0 ANSI: 0
Under 2.6.17:
Mar 29 15:45:11 ipp000 ARECA RAID ADAPTER0: 64BITS PCI BUS DMA ADDRESSING SUPPORTED
Mar 29 15:45:11 ipp000 ARECA RAID ADAPTER0: FIRMWARE VERSION V1.39 2005-12-13
Mar 29 15:45:11 ipp000 scsi4 : Areca SATA Host Adapter RAID Controller( RAID6 capable)
Mar 29 15:45:11 ipp000 Driver Version 1.20.0X.13
Mar 29 15:45:11 ipp000 Vendor: Areca Model: ARC-1170-VOL#00 Rev: R001
Mar 29 15:45:11 ipp000 Type: Direct-Access ANSI SCSI revision: 03
Mar 29 15:45:11 ipp000 sdb : very big device. try to use READ CAPACITY(16).
Mar 29 15:45:11 ipp000 SCSI device sdb: 8595693568 512-byte hdwr sectors (4400995 MB)
Mar 29 15:45:11 ipp000 sdb: Write Protect is off
Mar 29 15:45:11 ipp000 sdb: Mode Sense: cb 00 00 08
Mar 29 15:45:11 ipp000 SCSI device sdb: drive cache: write back
Mar 29 15:45:11 ipp000 sdb : very big device. try to use READ CAPACITY(16).
Mar 29 15:45:11 ipp000 SCSI device sdb: 8595693568 512-byte hdwr sectors (4400995 MB)
Mar 29 15:45:11 ipp000 sdb: Write Protect is off
Mar 29 15:45:11 ipp000 sdb: Mode Sense: cb 00 00 08
Mar 29 15:45:11 ipp000 SCSI device sdb: drive cache: write back
Mar 29 15:45:11 ipp000 sdb:<4>Alternate GPT is invalid, using primary GPT.
Mar 29 15:45:11 ipp000 sdb1
Mar 29 15:45:11 ipp000 sd 4:0:0:0: Attached scsi disk sdb
Mar 29 15:45:11 ipp000 sd 4:0:0:0: Attached scsi generic sg1 type 0
Mar 29 15:45:11 ipp000 Vendor: Areca Model: ARC-1170-VOL#01 Rev: R001
Mar 29 15:45:11 ipp000 Type: Direct-Access ANSI SCSI revision: 03
Mar 29 15:45:11 ipp000 sdc : very big device. try to use READ CAPACITY(16).
Mar 29 15:45:11 ipp000 SCSI device sdc: 8595580928 512-byte hdwr sectors (4400937 MB)
Mar 29 15:45:11 ipp000 sdc: Write Protect is off
Mar 29 15:45:11 ipp000 sdc: Mode Sense: cb 00 00 08
Mar 29 15:45:11 ipp000 SCSI device sdc: drive cache: write back
Mar 29 15:45:11 ipp000 sdc : very big device. try to use READ CAPACITY(16).
Mar 29 15:45:11 ipp000 SCSI device sdc: 8595580928 512-byte hdwr sectors (4400937 MB)
Mar 29 15:45:11 ipp000 sdc: Write Protect is off
Mar 29 15:45:11 ipp000 sdc: Mode Sense: cb 00 00 08
Mar 29 15:45:11 ipp000 SCSI device sdc: drive cache: write back
Mar 29 15:45:11 ipp000 sdc: sdc1
Mar 29 15:45:11 ipp000 sd 4:0:0:1: Attached scsi disk sdc
Mar 29 15:45:11 ipp000 sd 4:0:0:1: Attached scsi generic sg2 type 0
Mar 29 15:45:11 ipp000 Vendor: Areca Model: RAID controller Rev: R001
Mar 29 15:45:11 ipp000 Type: Processor ANSI SCSI revision: 00
Mar 29 15:45:11 ipp000 4:0:16:0: Attached scsi generic sg3 type 3
Mar 29 15:45:11 ipp000 arcmsr device major number 254
----- End forwarded message -----
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: difference between arcmsr (areca) 1.20.0X.13 & 2.6.20 in tree driver?
2007-04-03 3:21 difference between arcmsr (areca) 1.20.0X.13 & 2.6.20 in tree driver? Joshua Hoblitt
@ 2007-04-03 15:45 ` Randy Dunlap
2007-04-10 23:37 ` Joshua Hoblitt
0 siblings, 1 reply; 3+ messages in thread
From: Randy Dunlap @ 2007-04-03 15:45 UTC (permalink / raw)
To: Joshua Hoblitt; +Cc: linux-kernel, scsi
On Mon, 2 Apr 2007 17:21:35 -1000 Joshua Hoblitt wrote:
[adding linux-scsi]
> Has anyone else noticed this regression?
>
> -J
>
> --
> ----- Forwarded message from Joshua Hoblitt <jhoblitt@ifa.hawaii.edu> -----
>
> From: Joshua Hoblitt <jhoblitt@ifa.hawaii.edu>
> Date: Thu, 29 Mar 2007 16:38:20 -1000
> To: erich@areca.com.tw
> Subject: difference between 1.20.0X.13 & 2.6.20 in tree driver?
>
> Hello,
>
> I just attempted to upgrade a system from 2.6.17 (gentoo revision 8) w/
> 1.20.0X.13 to 2.6.20 (gentoo revision 4) with the in tree arcmsr driver.
> On the 2.6.17 kernel there are 2 ~4TB partitions that are visible on
> the system as /dev/sdb1 & /dev/sdc1. When the system is booted with the
> 2.6.20 kernel /dev/sdc1 is gone and /dev/sdb1 is properly reported as a
> 4TB EFI partition but fsck rejects the the filesystem as corrupt. Is
> this a regression or has there been a fundamental change in the way
> arcmsr represents the array to the block layer?
>
> Here is the info on the RAID card:
>
> Controller Name ARC-1170
> Firmware Version V1.39 2005-12-13
> BOOT ROM Version V1.39 2005-12-13
> Serial Number Y605CAAVAR700117
> Unit Serial #
> Main Processor 500MHz IOP331
> CPU ICache Size 32KBytes
> CPU DCache Size 32KBytes / Write Back
> System Memory 256MB / 333MHz
>
> Any idea as to what's going on?
>
> Thanks,
>
> -J
>
> --
> Under 2.6.20:
>
> Mar 29 15:41:05 ipp000 ARECA RAID ADAPTER4: FIRMWARE VERSION V1.39 2005-12-13
> Mar 29 15:41:05 ipp000 scsi4 : Areca SATA Host Adapter RAID Controller( RAID6 capable)
> Mar 29 15:41:05 ipp000 Driver Version 1.20.00.13
> Mar 29 15:41:05 ipp000 scsi 4:0:0:0: Direct-Access Areca ARC-1170-VOL#00 R001 PQ: 0 ANSI: 3
> Mar 29 15:41:05 ipp000 sdb : very big device. try to use READ CAPACITY(16).
> Mar 29 15:41:05 ipp000 SCSI device sdb: 8595693568 512-byte hdwr sectors (4400995 MB)
> Mar 29 15:41:05 ipp000 sdb: Write Protect is off
> Mar 29 15:41:05 ipp000 sdb: Mode Sense: cb 00 00 08
> Mar 29 15:41:05 ipp000 SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> Mar 29 15:41:05 ipp000 sdb : very big device. try to use READ CAPACITY(16).
> Mar 29 15:41:05 ipp000 SCSI device sdb: 8595693568 512-byte hdwr sectors (4400995 MB)
> Mar 29 15:41:05 ipp000 sdb: Write Protect is off
> Mar 29 15:41:05 ipp000 sdb: Mode Sense: cb 00 00 08
> Mar 29 15:41:05 ipp000 SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> Mar 29 15:41:05 ipp000 sdb: sdb1
> Mar 29 15:41:05 ipp000 sd 4:0:0:0: Attached scsi disk sdb
> Mar 29 15:41:05 ipp000 scsi 4:0:16:0: Processor Areca RAID controller R001 PQ: 0 ANSI: 0
>
> Under 2.6.17:
>
> Mar 29 15:45:11 ipp000 ARECA RAID ADAPTER0: 64BITS PCI BUS DMA ADDRESSING SUPPORTED
> Mar 29 15:45:11 ipp000 ARECA RAID ADAPTER0: FIRMWARE VERSION V1.39 2005-12-13
> Mar 29 15:45:11 ipp000 scsi4 : Areca SATA Host Adapter RAID Controller( RAID6 capable)
> Mar 29 15:45:11 ipp000 Driver Version 1.20.0X.13
> Mar 29 15:45:11 ipp000 Vendor: Areca Model: ARC-1170-VOL#00 Rev: R001
> Mar 29 15:45:11 ipp000 Type: Direct-Access ANSI SCSI revision: 03
> Mar 29 15:45:11 ipp000 sdb : very big device. try to use READ CAPACITY(16).
> Mar 29 15:45:11 ipp000 SCSI device sdb: 8595693568 512-byte hdwr sectors (4400995 MB)
> Mar 29 15:45:11 ipp000 sdb: Write Protect is off
> Mar 29 15:45:11 ipp000 sdb: Mode Sense: cb 00 00 08
> Mar 29 15:45:11 ipp000 SCSI device sdb: drive cache: write back
> Mar 29 15:45:11 ipp000 sdb : very big device. try to use READ CAPACITY(16).
> Mar 29 15:45:11 ipp000 SCSI device sdb: 8595693568 512-byte hdwr sectors (4400995 MB)
> Mar 29 15:45:11 ipp000 sdb: Write Protect is off
> Mar 29 15:45:11 ipp000 sdb: Mode Sense: cb 00 00 08
> Mar 29 15:45:11 ipp000 SCSI device sdb: drive cache: write back
> Mar 29 15:45:11 ipp000 sdb:<4>Alternate GPT is invalid, using primary GPT.
> Mar 29 15:45:11 ipp000 sdb1
> Mar 29 15:45:11 ipp000 sd 4:0:0:0: Attached scsi disk sdb
> Mar 29 15:45:11 ipp000 sd 4:0:0:0: Attached scsi generic sg1 type 0
> Mar 29 15:45:11 ipp000 Vendor: Areca Model: ARC-1170-VOL#01 Rev: R001
> Mar 29 15:45:11 ipp000 Type: Direct-Access ANSI SCSI revision: 03
> Mar 29 15:45:11 ipp000 sdc : very big device. try to use READ CAPACITY(16).
> Mar 29 15:45:11 ipp000 SCSI device sdc: 8595580928 512-byte hdwr sectors (4400937 MB)
> Mar 29 15:45:11 ipp000 sdc: Write Protect is off
> Mar 29 15:45:11 ipp000 sdc: Mode Sense: cb 00 00 08
> Mar 29 15:45:11 ipp000 SCSI device sdc: drive cache: write back
> Mar 29 15:45:11 ipp000 sdc : very big device. try to use READ CAPACITY(16).
> Mar 29 15:45:11 ipp000 SCSI device sdc: 8595580928 512-byte hdwr sectors (4400937 MB)
> Mar 29 15:45:11 ipp000 sdc: Write Protect is off
> Mar 29 15:45:11 ipp000 sdc: Mode Sense: cb 00 00 08
> Mar 29 15:45:11 ipp000 SCSI device sdc: drive cache: write back
> Mar 29 15:45:11 ipp000 sdc: sdc1
> Mar 29 15:45:11 ipp000 sd 4:0:0:1: Attached scsi disk sdc
> Mar 29 15:45:11 ipp000 sd 4:0:0:1: Attached scsi generic sg2 type 0
> Mar 29 15:45:11 ipp000 Vendor: Areca Model: RAID controller Rev: R001
> Mar 29 15:45:11 ipp000 Type: Processor ANSI SCSI revision: 00
> Mar 29 15:45:11 ipp000 4:0:16:0: Attached scsi generic sg3 type 3
> Mar 29 15:45:11 ipp000 arcmsr device major number 254
>
>
>
>
>
> ----- End forwarded message -----
>
---
~Randy
*** Remember to use Documentation/SubmitChecklist when testing your code ***
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: difference between arcmsr (areca) 1.20.0X.13 & 2.6.20 in tree driver?
2007-04-03 15:45 ` Randy Dunlap
@ 2007-04-10 23:37 ` Joshua Hoblitt
0 siblings, 0 replies; 3+ messages in thread
From: Joshua Hoblitt @ 2007-04-10 23:37 UTC (permalink / raw)
To: Randy Dunlap; +Cc: linux-kernel, scsi
[-- Attachment #1: Type: text/plain, Size: 6209 bytes --]
The RAID card in question has reported an "SPD CheckSum Error" (bad
ram?) during system power on so it's looking like this is probably a
hardware or firmware problem and not a driver issue.
-J
--
On Tue, Apr 03, 2007 at 08:45:38AM -0700, Randy Dunlap wrote:
> On Mon, 2 Apr 2007 17:21:35 -1000 Joshua Hoblitt wrote:
>
> [adding linux-scsi]
>
> > Has anyone else noticed this regression?
> >
> > -J
> >
> > --
> > ----- Forwarded message from Joshua Hoblitt <jhoblitt@ifa.hawaii.edu> -----
> >
> > From: Joshua Hoblitt <jhoblitt@ifa.hawaii.edu>
> > Date: Thu, 29 Mar 2007 16:38:20 -1000
> > To: erich@areca.com.tw
> > Subject: difference between 1.20.0X.13 & 2.6.20 in tree driver?
> >
> > Hello,
> >
> > I just attempted to upgrade a system from 2.6.17 (gentoo revision 8) w/
> > 1.20.0X.13 to 2.6.20 (gentoo revision 4) with the in tree arcmsr driver.
> > On the 2.6.17 kernel there are 2 ~4TB partitions that are visible on
> > the system as /dev/sdb1 & /dev/sdc1. When the system is booted with the
> > 2.6.20 kernel /dev/sdc1 is gone and /dev/sdb1 is properly reported as a
> > 4TB EFI partition but fsck rejects the the filesystem as corrupt. Is
> > this a regression or has there been a fundamental change in the way
> > arcmsr represents the array to the block layer?
> >
> > Here is the info on the RAID card:
> >
> > Controller Name ARC-1170
> > Firmware Version V1.39 2005-12-13
> > BOOT ROM Version V1.39 2005-12-13
> > Serial Number Y605CAAVAR700117
> > Unit Serial #
> > Main Processor 500MHz IOP331
> > CPU ICache Size 32KBytes
> > CPU DCache Size 32KBytes / Write Back
> > System Memory 256MB / 333MHz
> >
> > Any idea as to what's going on?
> >
> > Thanks,
> >
> > -J
> >
> > --
> > Under 2.6.20:
> >
> > Mar 29 15:41:05 ipp000 ARECA RAID ADAPTER4: FIRMWARE VERSION V1.39 2005-12-13
> > Mar 29 15:41:05 ipp000 scsi4 : Areca SATA Host Adapter RAID Controller( RAID6 capable)
> > Mar 29 15:41:05 ipp000 Driver Version 1.20.00.13
> > Mar 29 15:41:05 ipp000 scsi 4:0:0:0: Direct-Access Areca ARC-1170-VOL#00 R001 PQ: 0 ANSI: 3
> > Mar 29 15:41:05 ipp000 sdb : very big device. try to use READ CAPACITY(16).
> > Mar 29 15:41:05 ipp000 SCSI device sdb: 8595693568 512-byte hdwr sectors (4400995 MB)
> > Mar 29 15:41:05 ipp000 sdb: Write Protect is off
> > Mar 29 15:41:05 ipp000 sdb: Mode Sense: cb 00 00 08
> > Mar 29 15:41:05 ipp000 SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> > Mar 29 15:41:05 ipp000 sdb : very big device. try to use READ CAPACITY(16).
> > Mar 29 15:41:05 ipp000 SCSI device sdb: 8595693568 512-byte hdwr sectors (4400995 MB)
> > Mar 29 15:41:05 ipp000 sdb: Write Protect is off
> > Mar 29 15:41:05 ipp000 sdb: Mode Sense: cb 00 00 08
> > Mar 29 15:41:05 ipp000 SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> > Mar 29 15:41:05 ipp000 sdb: sdb1
> > Mar 29 15:41:05 ipp000 sd 4:0:0:0: Attached scsi disk sdb
> > Mar 29 15:41:05 ipp000 scsi 4:0:16:0: Processor Areca RAID controller R001 PQ: 0 ANSI: 0
> >
> > Under 2.6.17:
> >
> > Mar 29 15:45:11 ipp000 ARECA RAID ADAPTER0: 64BITS PCI BUS DMA ADDRESSING SUPPORTED
> > Mar 29 15:45:11 ipp000 ARECA RAID ADAPTER0: FIRMWARE VERSION V1.39 2005-12-13
> > Mar 29 15:45:11 ipp000 scsi4 : Areca SATA Host Adapter RAID Controller( RAID6 capable)
> > Mar 29 15:45:11 ipp000 Driver Version 1.20.0X.13
> > Mar 29 15:45:11 ipp000 Vendor: Areca Model: ARC-1170-VOL#00 Rev: R001
> > Mar 29 15:45:11 ipp000 Type: Direct-Access ANSI SCSI revision: 03
> > Mar 29 15:45:11 ipp000 sdb : very big device. try to use READ CAPACITY(16).
> > Mar 29 15:45:11 ipp000 SCSI device sdb: 8595693568 512-byte hdwr sectors (4400995 MB)
> > Mar 29 15:45:11 ipp000 sdb: Write Protect is off
> > Mar 29 15:45:11 ipp000 sdb: Mode Sense: cb 00 00 08
> > Mar 29 15:45:11 ipp000 SCSI device sdb: drive cache: write back
> > Mar 29 15:45:11 ipp000 sdb : very big device. try to use READ CAPACITY(16).
> > Mar 29 15:45:11 ipp000 SCSI device sdb: 8595693568 512-byte hdwr sectors (4400995 MB)
> > Mar 29 15:45:11 ipp000 sdb: Write Protect is off
> > Mar 29 15:45:11 ipp000 sdb: Mode Sense: cb 00 00 08
> > Mar 29 15:45:11 ipp000 SCSI device sdb: drive cache: write back
> > Mar 29 15:45:11 ipp000 sdb:<4>Alternate GPT is invalid, using primary GPT.
> > Mar 29 15:45:11 ipp000 sdb1
> > Mar 29 15:45:11 ipp000 sd 4:0:0:0: Attached scsi disk sdb
> > Mar 29 15:45:11 ipp000 sd 4:0:0:0: Attached scsi generic sg1 type 0
> > Mar 29 15:45:11 ipp000 Vendor: Areca Model: ARC-1170-VOL#01 Rev: R001
> > Mar 29 15:45:11 ipp000 Type: Direct-Access ANSI SCSI revision: 03
> > Mar 29 15:45:11 ipp000 sdc : very big device. try to use READ CAPACITY(16).
> > Mar 29 15:45:11 ipp000 SCSI device sdc: 8595580928 512-byte hdwr sectors (4400937 MB)
> > Mar 29 15:45:11 ipp000 sdc: Write Protect is off
> > Mar 29 15:45:11 ipp000 sdc: Mode Sense: cb 00 00 08
> > Mar 29 15:45:11 ipp000 SCSI device sdc: drive cache: write back
> > Mar 29 15:45:11 ipp000 sdc : very big device. try to use READ CAPACITY(16).
> > Mar 29 15:45:11 ipp000 SCSI device sdc: 8595580928 512-byte hdwr sectors (4400937 MB)
> > Mar 29 15:45:11 ipp000 sdc: Write Protect is off
> > Mar 29 15:45:11 ipp000 sdc: Mode Sense: cb 00 00 08
> > Mar 29 15:45:11 ipp000 SCSI device sdc: drive cache: write back
> > Mar 29 15:45:11 ipp000 sdc: sdc1
> > Mar 29 15:45:11 ipp000 sd 4:0:0:1: Attached scsi disk sdc
> > Mar 29 15:45:11 ipp000 sd 4:0:0:1: Attached scsi generic sg2 type 0
> > Mar 29 15:45:11 ipp000 Vendor: Areca Model: RAID controller Rev: R001
> > Mar 29 15:45:11 ipp000 Type: Processor ANSI SCSI revision: 00
> > Mar 29 15:45:11 ipp000 4:0:16:0: Attached scsi generic sg3 type 3
> > Mar 29 15:45:11 ipp000 arcmsr device major number 254
> >
> >
> >
> >
> >
> > ----- End forwarded message -----
> >
>
>
> ---
> ~Randy
> *** Remember to use Documentation/SubmitChecklist when testing your code ***
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2007-04-10 23:33 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2007-04-03 3:21 difference between arcmsr (areca) 1.20.0X.13 & 2.6.20 in tree driver? Joshua Hoblitt
2007-04-03 15:45 ` Randy Dunlap
2007-04-10 23:37 ` Joshua Hoblitt
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®