From: Andrew Morton <akpm@linux-foundation.org>
To: Andy Whitcroft <apw@shadowen.org>
Cc: linux-kernel@vger.kernel.org, mel@csn.ul.ie,
Jens Axboe <jens.axboe@oracle.com>,
linux-scsi@vger.kernel.org
Subject: Re: 2.6.23-rc4-mm1
Date: Mon, 10 Sep 2007 11:19:26 -0700 [thread overview]
Message-ID: <20070910111926.9c942358.akpm@linux-foundation.org> (raw)
In-Reply-To: <20070910174926.GC30335@shadowen.org>
On Mon, 10 Sep 2007 18:49:26 +0100 Andy Whitcroft <apw@shadowen.org> wrote:
> I have a couple of old NUMA-Q systems which are unable to read their
> boot disks with 2.6.23-rc4-mm1. The disks appear to be recognised and
> even the partition tables read correctly, and then they go pop:
>
> qla1280: QLA1040 found on PCI bus 0, dev 10
cc's added.
> Clocksource tsc unstable (delta = 99922590 ns)
> Time: jiffies clocksource has been installed.
> scsi(0:0): Resetting SCSI BUS
> scsi0 : QLogic QLA1040 PCI to SCSI Host Adapter
> Firmware version: 7.65.06, Driver version 3.26
> scsi 0:0:0:0: Direct-Access IBM DGHS18X 0360 PQ: 0 ANSI: 3
> scsi(0:0:0:0): Sync: period 10, offset 12, Wide
> scsi 0:0:1:0: Direct-Access IBM OEM DCHS09X 5454 PQ: 0 ANSI: 2
> scsi(0:0:1:0): Sync: period 10, offset 12, Wide
> scsi 0:0:2:0: Direct-Access IBM OEM DCHS09X 5454 PQ: 0 ANSI: 2
> scsi(0:0:2:0): Sync: period 10, offset 12, Wide
> scsi 0:0:3:0: Direct-Access IBM OEM DCHS09X 5454 PQ: 0 ANSI: 2
> scsi(0:0:3:0): Sync: period 10, offset 12, Wide
> scsi 0:0:4:0: Direct-Access IBM OEM DCHS09X 5454 PQ: 0 ANSI: 2
> scsi(0:0:4:0): Sync: period 10, offset 12, Wide
> st: Version 20070203, fixed bufsize 32768, s/g segs 256
> sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sda: sda1
> sd 0:0:0:0: [sda] Attached SCSI disk
> sd 0:0:1:0: [sdb] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:1:0: [sdb] Write Protect is off
> sd 0:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 0:0:1:0: [sdb] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:1:0: [sdb] Write Protect is off
> sd 0:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sdb: unknown partition table
> sd 0:0:1:0: [sdb] Attached SCSI disk
> sd 0:0:2:0: [sdc] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:2:0: [sdc] Write Protect is off
> sd 0:0:2:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 0:0:2:0: [sdc] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:2:0: [sdc] Write Protect is off
> sd 0:0:2:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sdc: sdc1
> sd 0:0:2:0: [sdc] Attached SCSI disk
> sd 0:0:3:0: [sdd] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:3:0: [sdd] Write Protect is off
> sd 0:0:3:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 0:0:3:0: [sdd] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:3:0: [sdd] Write Protect is off
> sd 0:0:3:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sdd: sdd1
> sd 0:0:3:0: [sdd] Attached SCSI disk
> sd 0:0:4:0: [sde] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:4:0: [sde] Write Protect is off
> sd 0:0:4:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 0:0:4:0: [sde] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:4:0: [sde] Write Protect is off
> sd 0:0:4:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sde: unknown partition table
> sd 0:0:4:0: [sde] Attached SCSI disk
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> sd 0:0:1:0: Attached scsi generic sg1 type 0
> sd 0:0:2:0: Attached scsi generic sg2 type 0
> sd 0:0:3:0: Attached scsi generic sg3 type 0
> sd 0:0:4:0: Attached scsi generic sg4 type 0
> serio: i8042 KBD port at 0x60,0x64 irq 1
> serio: i8042 AUX port at 0x60,0x64 irq 12
> mice: PS/2 mouse device common for all mice
> input: AT Translated Set 2 keyboard as /class/input/input0
> oprofile: using NMI interrupt.
> TCP cubic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> Using IPI Shortcut mode
> input: PS/2 Logitech Mouse as /class/input/input1
> RAMDISK: cramfs filesystem found at block 0
> RAMDISK: Loading 1244KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
> VFS: Mounted root (cramfs filesystem) readonly.
> Freeing unused kernel memory: 220k freed
> initrd-tools: 0.1.81.1
> mount: fs type devfs not supported by kernel
> FATAL: Module sd_mod not found.
> umount: devfs: not mounted
> ext3: No journal on filesystem on sda1
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 63
> Buffer I/O error on device sda1, logical block 0
> Buffer I/O error on device sda1, logical block 1
> Buffer I/O error on device sda1, logical block 2
> Buffer I/O error on device sda1, logical block 3
> mount: fs type devfs not supported by kernel
> ext3: No journal on filesystem on sda1
> umount: devfs: not mounted
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 28010831
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 31080815
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 31080855
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 31080919
> Buffer I/O error on device sda1, logical block 3885107
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 28411047
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 31135687
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 31138007
> sd 0:0:0:0: [sda] <6>sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
>
The only patch which touches qla1280 is git-block.patch. From a quick
squizz the change looks OK, although it's tricky and something might have
broken.
(the dprintk at line 2929 needs to print remseg, not seg_cnt).
Can you retest with that change reverted (below)? If it's not that then
perhaps something in scsi core broke, dunno.
diff -puN drivers/scsi/qla1280.c~revert-1 drivers/scsi/qla1280.c
--- a/drivers/scsi/qla1280.c~revert-1
+++ a/drivers/scsi/qla1280.c
@@ -2775,7 +2775,7 @@ qla1280_64bit_start_scsi(struct scsi_qla
struct device_reg __iomem *reg = ha->iobase;
struct scsi_cmnd *cmd = sp->cmd;
cmd_a64_entry_t *pkt;
- struct scatterlist *sg = NULL, *s;
+ struct scatterlist *sg = NULL;
__le32 *dword_ptr;
dma_addr_t dma_handle;
int status = 0;
@@ -2889,16 +2889,13 @@ qla1280_64bit_start_scsi(struct scsi_qla
* Load data segments.
*/
if (seg_cnt) { /* If data transfer. */
- int remseg = seg_cnt;
/* Setup packet address segment pointer. */
dword_ptr = (u32 *)&pkt->dseg_0_address;
if (cmd->use_sg) { /* If scatter gather */
/* Load command entry data segments. */
- for_each_sg(sg, s, seg_cnt, cnt) {
- if (cnt == 2)
- break;
- dma_handle = sg_dma_address(s);
+ for (cnt = 0; cnt < 2 && seg_cnt; cnt++, seg_cnt--) {
+ dma_handle = sg_dma_address(sg);
#if defined(CONFIG_IA64_GENERIC) || defined(CONFIG_IA64_SGI_SN2)
if (ha->flags.use_pci_vchannel)
sn_pci_set_vchan(ha->pdev,
@@ -2909,12 +2906,12 @@ qla1280_64bit_start_scsi(struct scsi_qla
cpu_to_le32(pci_dma_lo32(dma_handle));
*dword_ptr++ =
cpu_to_le32(pci_dma_hi32(dma_handle));
- *dword_ptr++ = cpu_to_le32(sg_dma_len(s));
+ *dword_ptr++ = cpu_to_le32(sg_dma_len(sg));
+ sg++;
dprintk(3, "S/G Segment phys_addr=%x %x, len=0x%x\n",
cpu_to_le32(pci_dma_hi32(dma_handle)),
cpu_to_le32(pci_dma_lo32(dma_handle)),
- cpu_to_le32(sg_dma_len(sg_next(s))));
- remseg--;
+ cpu_to_le32(sg_dma_len(sg)));
}
dprintk(5, "qla1280_64bit_start_scsi: Scatter/gather "
"command packet data - b %i, t %i, l %i \n",
@@ -2929,9 +2926,7 @@ qla1280_64bit_start_scsi(struct scsi_qla
dprintk(3, "S/G Building Continuation...seg_cnt=0x%x "
"remains\n", seg_cnt);
- while (remseg > 0) {
- /* Update sg start */
- sg = s;
+ while (seg_cnt > 0) {
/* Adjust ring index. */
ha->req_ring_index++;
if (ha->req_ring_index == REQUEST_ENTRY_CNT) {
@@ -2957,10 +2952,9 @@ qla1280_64bit_start_scsi(struct scsi_qla
(u32 *)&((struct cont_a64_entry *) pkt)->dseg_0_address;
/* Load continuation entry data segments. */
- for_each_sg(sg, s, remseg, cnt) {
- if (cnt == 5)
- break;
- dma_handle = sg_dma_address(s);
+ for (cnt = 0; cnt < 5 && seg_cnt;
+ cnt++, seg_cnt--) {
+ dma_handle = sg_dma_address(sg);
#if defined(CONFIG_IA64_GENERIC) || defined(CONFIG_IA64_SGI_SN2)
if (ha->flags.use_pci_vchannel)
sn_pci_set_vchan(ha->pdev,
@@ -2972,12 +2966,12 @@ qla1280_64bit_start_scsi(struct scsi_qla
*dword_ptr++ =
cpu_to_le32(pci_dma_hi32(dma_handle));
*dword_ptr++ =
- cpu_to_le32(sg_dma_len(s));
+ cpu_to_le32(sg_dma_len(sg));
dprintk(3, "S/G Segment Cont. phys_addr=%x %x, len=0x%x\n",
cpu_to_le32(pci_dma_hi32(dma_handle)),
cpu_to_le32(pci_dma_lo32(dma_handle)),
- cpu_to_le32(sg_dma_len(s)));
- remseg--;
+ cpu_to_le32(sg_dma_len(sg)));
+ sg++;
}
dprintk(5, "qla1280_64bit_start_scsi: "
"continuation packet data - b %i, t "
@@ -3068,7 +3062,7 @@ qla1280_32bit_start_scsi(struct scsi_qla
struct device_reg __iomem *reg = ha->iobase;
struct scsi_cmnd *cmd = sp->cmd;
struct cmd_entry *pkt;
- struct scatterlist *sg = NULL, *s;
+ struct scatterlist *sg = NULL;
__le32 *dword_ptr;
int status = 0;
int cnt;
@@ -3194,7 +3188,6 @@ qla1280_32bit_start_scsi(struct scsi_qla
* Load data segments.
*/
if (seg_cnt) {
- int remseg = seg_cnt;
/* Setup packet address segment pointer. */
dword_ptr = &pkt->dseg_0_address;
@@ -3203,25 +3196,22 @@ qla1280_32bit_start_scsi(struct scsi_qla
qla1280_dump_buffer(1, (char *)sg, 4 * 16);
/* Load command entry data segments. */
- for_each_sg(sg, s, seg_cnt, cnt) {
- if (cnt == 4)
- break;
+ for (cnt = 0; cnt < 4 && seg_cnt; cnt++, seg_cnt--) {
*dword_ptr++ =
- cpu_to_le32(pci_dma_lo32(sg_dma_address(s)));
- *dword_ptr++ = cpu_to_le32(sg_dma_len(s));
+ cpu_to_le32(pci_dma_lo32(sg_dma_address(sg)));
+ *dword_ptr++ =
+ cpu_to_le32(sg_dma_len(sg));
dprintk(3, "S/G Segment phys_addr=0x%lx, len=0x%x\n",
- (pci_dma_lo32(sg_dma_address(s))),
- (sg_dma_len(s)));
- remseg--;
+ (pci_dma_lo32(sg_dma_address(sg))),
+ (sg_dma_len(sg)));
+ sg++;
}
/*
* Build continuation packets.
*/
dprintk(3, "S/G Building Continuation"
"...seg_cnt=0x%x remains\n", seg_cnt);
- while (remseg > 0) {
- /* Continue from end point */
- sg = s;
+ while (seg_cnt > 0) {
/* Adjust ring index. */
ha->req_ring_index++;
if (ha->req_ring_index == REQUEST_ENTRY_CNT) {
@@ -3249,16 +3239,18 @@ qla1280_32bit_start_scsi(struct scsi_qla
&((struct cont_entry *) pkt)->dseg_0_address;
/* Load continuation entry data segments. */
- for_each_sg(sg, s, remseg, cnt) {
+ for (cnt = 0; cnt < 7 && seg_cnt;
+ cnt++, seg_cnt--) {
*dword_ptr++ =
- cpu_to_le32(pci_dma_lo32(sg_dma_address(s)));
+ cpu_to_le32(pci_dma_lo32(sg_dma_address(sg)));
*dword_ptr++ =
- cpu_to_le32(sg_dma_len(s));
+ cpu_to_le32(sg_dma_len(sg));
dprintk(1,
"S/G Segment Cont. phys_addr=0x%x, "
"len=0x%x\n",
- cpu_to_le32(pci_dma_lo32(sg_dma_address(s))),
- cpu_to_le32(sg_dma_len(s)));
+ cpu_to_le32(pci_dma_lo32(sg_dma_address(sg))),
+ cpu_to_le32(sg_dma_len(sg)));
+ sg++;
}
dprintk(5, "qla1280_32bit_start_scsi: "
"continuation packet data - "
_
next prev parent reply other threads:[~2007-09-10 18:21 UTC|newest]
Thread overview: 158+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-09-01 4:58 2.6.23-rc4-mm1 Andrew Morton
2007-09-01 6:53 ` 2.6.23-rc4-mm1 KAMEZAWA Hiroyuki
2007-09-01 6:58 ` 2.6.23-rc4-mm1 Andrew Morton
2007-09-01 8:54 ` 2.6.23-rc4-mm1 Herbert Xu
2007-09-01 21:09 ` 2.6.23-rc4-mm1 Satyam Sharma
2007-09-02 1:46 ` 2.6.23-rc4-mm1 Herbert Xu
2007-09-02 2:52 ` 2.6.23-rc4-mm1 Satyam Sharma
2007-09-02 3:59 ` 2.6.23-rc4-mm1 Herbert Xu
2007-09-01 11:55 ` 2.6.23-rc4-mm1 Kamalesh Babulal
2007-09-01 14:18 ` 2.6.23-rc4-mm1: geode fb compile error Adrian Bunk
2007-09-01 17:03 ` Satyam Sharma
2007-09-01 15:19 ` 2.6.23-rc4-mm1: two ktime_sub_ns() functions Adrian Bunk
2007-09-01 15:44 ` 2.6.23-rc4-mm1: mips compile error Adrian Bunk
2007-09-04 5:27 ` Mathieu Desnoyers
2007-09-04 10:21 ` Ralf Baechle
2007-09-01 16:07 ` 2.6.23-rc4-mm1 Torsten Kaiser
2007-09-01 16:16 ` 2.6.23-rc4-mm1 Andrew Morton
2007-09-01 18:13 ` 2.6.23-rc4-mm1 OOPS in forcedeth? thunder7
2007-09-01 19:05 ` Jeff Garzik
2007-09-02 0:54 ` Satyam Sharma
2007-09-02 5:36 ` thunder7
2007-09-02 6:19 ` thunder7
2007-09-02 9:55 ` Satyam Sharma
2007-09-14 3:51 ` Andrew James Wade
2007-09-17 13:57 ` Dhaval Giani
2007-09-17 14:07 ` Denis V. Lunev
2007-09-17 21:00 ` Vlad Yasevich
2007-09-17 23:56 ` Satyam Sharma
2007-09-01 22:06 ` 2.6.23-rc4-mm1 "no CRC" MODPOST warnings Satyam Sharma
2007-09-01 22:40 ` Adrian Bunk
2007-09-01 23:15 ` Sam Ravnborg
2007-09-01 23:12 ` [PATCH -mm] softlockup-improve-debug-output.patch fix Satyam Sharma
2007-09-02 12:37 ` [PATCH -mm][resend] " Satyam Sharma
2007-09-02 12:28 ` Ingo Molnar
2007-09-06 6:52 ` [PATCH] sched: Use show_regs() to improve __schedule_bug() output Satyam Sharma
2007-10-22 12:35 ` Ingo Molnar
2007-09-03 16:36 ` [PATCH -mm][resend] softlockup-improve-debug-output.patch fix Valdis.Kletnieks
2007-09-01 23:42 ` [PATCH -mm] drivers/acpi/tables/tbutils.c: Shut up bogus uninitialized variable warning Satyam Sharma
2007-09-02 0:19 ` Adrian Bunk
2007-09-02 1:02 ` Satyam Sharma
2007-09-02 1:30 ` [PATCH -mm] net/sched/sch_cbq.c: Shut up " Satyam Sharma
2007-09-02 11:36 ` Patrick McHardy
2007-09-02 2:36 ` 2.6.23-rc4-mm1: unpingable box and NULL dereference at tcp_rto_min() Alexey Dobriyan
2007-09-02 5:02 ` Satyam Sharma
2007-09-02 20:52 ` Andrew Morton
2007-09-02 21:19 ` Alexey Dobriyan
2007-09-02 9:14 ` 2.6.23-rc4-mm1 net bitops compile error Adrian Bunk
2007-09-04 17:53 ` Jiri Slaby
2007-09-02 11:25 ` [-mm patch] IPV6 must select XFRM Adrian Bunk
2007-09-03 10:43 ` Masahide NAKAMURA
2007-09-06 10:01 ` net-26.24 broken with XFRM off Noriaki TAKAMIYA
2007-09-02 13:00 ` [PATCH -mm] drivers/char/nozomi.c: __devexit_p usage build fix Satyam Sharma
2007-09-02 19:01 ` 2.6.23-rc4-mm1: broke pata_via cable detection Laurent Riffard
2007-09-02 19:20 ` Alan Cox
2007-09-11 1:50 ` Jeff Garzik
2007-09-02 20:39 ` 2.6.23-rc4-mm1: boot failure on HPC nx6325 Rafael J. Wysocki
2007-09-03 8:36 ` Thomas Gleixner
2007-09-03 10:15 ` Rafael J. Wysocki
2007-09-03 20:51 ` Rafael J. Wysocki
2007-09-04 1:03 ` Thomas Gleixner
2007-09-03 4:30 ` 2.6.23-rc4-mm1 Randy Dunlap
2007-09-03 19:25 ` 2.6.23-rc4-mm1 Wim Van Sebroeck
2007-09-03 22:32 ` 2.6.23-rc4-mm1 Satyam Sharma
2007-09-04 21:21 ` 2.6.23-rc4-mm1 Wim Van Sebroeck
2007-09-04 17:54 ` 2.6.23-rc4-mm1 Zach Carter
2007-09-04 21:36 ` 2.6.23-rc4-mm1 Stephen Hemminger
2007-09-05 14:37 ` 2.6.23-rc4-mm1 Valdis.Kletnieks
2007-09-05 15:12 ` 2.6.23-rc4-mm1 Andrew Morton
2007-09-05 15:20 ` 2.6.23-rc4-mm1 Balbir Singh
2007-09-05 15:58 ` 2.6.23-rc4-mm1 Valdis.Kletnieks
2007-09-05 19:46 ` 2.6.23-rc4-mm1 - git-alsa.patch breaks audio on Dell Latitude D820 Valdis.Kletnieks
2007-09-05 19:54 ` Valdis.Kletnieks
2007-09-05 20:22 ` Takashi Iwai
2007-09-05 20:11 ` Takashi Iwai
2007-09-05 20:27 ` Takashi Iwai
2007-09-05 21:16 ` Valdis.Kletnieks
2007-09-05 21:39 ` Takashi Iwai
2007-09-06 14:10 ` Valdis.Kletnieks
2007-09-06 14:17 ` Takashi Iwai
2007-09-06 19:37 ` 2.6.23-rc4-mm1 myri10ge module link error on x86_64 Mathieu Desnoyers
2007-09-06 20:40 ` David Miller
2007-09-06 20:48 ` David Miller
2007-09-07 23:59 ` Jeff Garzik
2007-09-08 0:25 ` Daniel Walker
2007-10-13 22:03 ` Avuton Olrich
2007-09-09 12:22 ` 2.6.23-rc4-mm1 Mel Gorman
2007-09-14 15:12 ` ath5k driver not working on ThinkPad Robert de Rooy
2007-09-09 20:24 ` [-mm patch] alpha bitops.h must #include <asm/barrier.h> Adrian Bunk
2007-09-09 20:24 ` [-mm patch] remove ide_get_error_location() Adrian Bunk
2007-09-11 21:27 ` Bartlomiej Zolnierkiewicz
2007-09-12 5:54 ` Jens Axboe
2007-09-09 20:24 ` [-mm patch] drivers/dma/ioat_dma.c: make 3 functions static Adrian Bunk
2007-09-09 20:25 ` [-mm patch] usb/serial/ch341.c: make 4 " Adrian Bunk
2007-09-09 20:25 ` [-mm patch] make nfs_wb_page_priority() static Adrian Bunk
2007-09-09 20:25 ` [-mm patch] kernel/kexec.c: make code static Adrian Bunk
2007-09-10 2:55 ` Ken'ichi Ohmichi
2007-09-10 12:20 ` Adrian Bunk
2007-09-11 5:53 ` Maneesh Soni
2007-09-12 7:37 ` Ken'ichi Ohmichi
2007-09-09 20:25 ` [-mm patch] really unexport do_softirq Adrian Bunk
2007-09-12 13:14 ` David Miller
2007-09-09 20:25 ` [-mm patch] unexport raise_softirq_irqoff Adrian Bunk
2007-09-09 20:41 ` Christoph Hellwig
2007-09-12 13:15 ` David Miller
2007-09-09 20:25 ` [-mm patch] mm/memcontrol.c: clenups Adrian Bunk
2007-09-10 8:23 ` Balbir Singh
2007-09-10 19:58 ` Jan Engelhardt
2007-09-10 19:59 ` Jan Engelhardt
2007-09-10 21:59 ` Adrian Bunk
2007-09-11 2:41 ` Balbir Singh
2007-09-09 20:25 ` [-mm patch] net/sctp/socket.c: make 3 variables static Adrian Bunk
2007-09-10 14:05 ` [Lksctp-developers] " Neil Horman
2007-09-12 13:18 ` David Miller
2007-09-09 20:25 ` [-mm patch] make tcp_splice_data_recv() static Adrian Bunk
2007-09-12 13:21 ` David Miller
2007-09-12 17:44 ` Jens Axboe
2007-09-09 20:26 ` [-mm patch] make do_try_to_free_pages() static Adrian Bunk
2007-09-10 8:24 ` Balbir Singh
2007-09-10 17:43 ` 2.6.23-rc4-mm1 -- powerpc per_cpu__cpu_sibling_map compile failure Andy Whitcroft
2007-09-10 17:49 ` 2.6.23-rc4-mm1 Andy Whitcroft
2007-09-10 18:19 ` Andrew Morton [this message]
2007-09-10 18:59 ` 2.6.23-rc4-mm1 Torsten Kaiser
2007-09-10 19:20 ` 2.6.23-rc4-mm1 Andrew Morton
2007-09-10 19:38 ` 2.6.23-rc4-mm1 Torsten Kaiser
2007-09-10 19:42 ` 2.6.23-rc4-mm1 FUJITA Tomonori
2007-09-10 20:43 ` 2.6.23-rc4-mm1 Torsten Kaiser
2007-09-11 8:32 ` 2.6.23-rc4-mm1 Jens Axboe
2007-09-10 19:10 ` 2.6.23-rc4-mm1 FUJITA Tomonori
2007-09-13 17:34 ` 2.6.23-rc4-mm1 Andy Whitcroft
2007-09-15 4:16 ` 2.6.23-rc4-mm1 Paul Jackson
2007-09-15 10:52 ` 2.6.23-rc4-mm1 FUJITA Tomonori
2007-09-17 13:28 ` 2.6.23-rc4-mm1 Jens Axboe
2007-09-17 14:32 ` 2.6.23-rc4-mm1 FUJITA Tomonori
2007-09-18 10:18 ` 2.6.23-rc4-mm1 Jens Axboe
2007-09-18 12:25 ` 2.6.23-rc4-mm1 FUJITA Tomonori
2007-09-18 12:51 ` 2.6.23-rc4-mm1 Jens Axboe
2007-09-10 19:31 ` 2.6.23-rc4-mm1 FUJITA Tomonori
2007-09-14 8:10 ` 2.6.23-rc4-mm1 Andy Whitcroft
2007-09-14 13:01 ` 2.6.23-rc4-mm1 Torsten Kaiser
2007-09-14 20:15 ` 2.6.23-rc4-mm1 Andrew Morton
2007-09-10 20:19 ` 2.6.23-rc4-mm1: git-block.patch broke pktcdvd Laurent Riffard
2007-09-13 22:50 ` Laurent Riffard
2007-09-13 23:05 ` Andrew Morton
2007-09-14 8:00 ` Jens Axboe
2007-09-14 8:30 ` Jens Axboe
2007-09-14 9:33 ` Jens Axboe
2007-09-14 11:06 ` Jens Axboe
2007-09-14 19:04 ` Laurent Riffard
2007-09-20 21:25 ` [PATCH] pktcdvd: don't rely on bio_init() preserving bio->bi_destructor Laurent Riffard
2007-09-21 5:19 ` Jens Axboe
2007-09-02 2:56 2.6.23-rc4-mm1 Mats Johannesson
2007-09-03 8:06 ` 2.6.23-rc4-mm1 Nicolas Mailhot
2007-09-04 15:20 ` 2.6.23-rc4-mm1 Alistair John Strachan
2007-09-04 15:26 ` 2.6.23-rc4-mm1 Andi Kleen
2007-09-04 16:05 ` 2.6.23-rc4-mm1 Alistair John Strachan
2007-09-06 7:25 net-26.24 broken with XFRM off Divy Le Ray
2007-09-06 8:13 ` Eric Dumazet
2007-09-06 9:50 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20070910111926.9c942358.akpm@linux-foundation.org \
--to=akpm@linux-foundation.org \
--cc=apw@shadowen.org \
--cc=jens.axboe@oracle.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
--cc=mel@csn.ul.ie \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome