* [PATCH 2.6.26-rc-mm] gpio max7301: check spi_setup() return code, cleanup
@ 2008-06-28 1:37 David Brownell
0 siblings, 0 replies; only message in thread
From: David Brownell @ 2008-06-28 1:37 UTC (permalink / raw)
To: Andrew Morton; +Cc: Guennadi Liakhovetski, lkml
From: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Fix inaccuracies in comments, check spi_setup() return code, mask off high
byte in max7301_read(). Thanks to David Brownell for the review.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
---
Same as what Guennadi sent 12-june, but with a minor comment tweak.
drivers/gpio/max7301.c | 15 +++++++++------
1 file changed, 9 insertions(+), 6 deletions(-)
--- a/drivers/gpio/max7301.c 2008-06-27 18:29:35.000000000 -0700
+++ b/drivers/gpio/max7301.c 2008-06-27 18:30:23.000000000 -0700
@@ -71,7 +71,7 @@ struct max7301 {
*
* A write to the MAX7301 means one message with one transfer
*
- * Returns 0 if successfull or a negative value on error
+ * Returns 0 if successful or a negative value on error
*/
static int max7301_write(struct spi_device *spi, unsigned int reg, unsigned int val)
{
@@ -84,9 +84,9 @@ static int max7301_write(struct spi_devi
* @spi: The SPI device
* @reg: Register offset
*
- * A read from the MAX7301 means one message with two transfers
+ * A read from the MAX7301 means two transfers; here, one message each
*
- * Returns positive 8 bit value from device if successfull or a
+ * Returns positive 8 bit value from device if successful or a
* negative value on error
*/
static int max7301_read(struct spi_device *spi, unsigned int reg)
@@ -99,12 +99,13 @@ static int max7301_read(struct spi_devic
if (ret)
return ret;
/*
- * FIXME: This read should write 0x0000 (=NOOP at MAX7301 side)
+ * This relies on the fact, that a transfer with NULL tx_buf shifts out
+ * zero bytes (=NOOP for MAX7301)
*/
ret = spi_read(spi, (u8 *)&word, sizeof(word));
if (ret)
return ret;
- return word;
+ return word & 0xff;
}
static int max7301_direction_input(struct gpio_chip *chip, unsigned offset)
@@ -224,7 +225,9 @@ static int __devinit max7301_probe(struc
*/
spi->bits_per_word = 16;
- spi->master->setup(spi);
+ ret = spi_setup(spi);
+ if (ret < 0)
+ return ret;
ts = kzalloc(sizeof(struct max7301), GFP_KERNEL);
if (!ts)
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2008-06-29 5:03 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2008-06-28 1:37 [PATCH 2.6.26-rc-mm] gpio max7301: check spi_setup() return code, cleanup David Brownell
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®