* Re: [2.6.34-rc1] Problem using USB 1.1 device on USB 3.0 xhci host controller
[not found] ` <20100312232538.GA13353@xanatos>
@ 2010-03-13 11:01 ` Sander Eikelenboom
2010-03-15 3:05 ` Libin
0 siblings, 1 reply; 4+ messages in thread
From: Sander Eikelenboom @ 2010-03-13 11:01 UTC (permalink / raw)
To: Sarah Sharp; +Cc: linux-usb, linux-kernel, andiry.xu, libin.yang
[-- Attachment #1: Type: text/plain, Size: 34011 bytes --]
The patches applied cleanly, but the device doesn't work yet.
complete dmesg and lsusb -vvv attached.
Highlights from dmesg:
[ 1.738043] usb 9-3: skipped 4 descriptors after interface
[ 1.738045] usb 9-3: skipped 2 descriptors after interface
[ 1.738048] usb 9-3: skipped 1 descriptor after endpoint
[ 1.738050] usb 9-3: skipped 2 descriptors after interface
[ 1.738053] usb 9-3: skipped 1 descriptor after endpoint
[ 1.738055] usb 9-3: skipped 2 descriptors after interface
[ 1.738057] usb 9-3: skipped 1 descriptor after endpoint
[ 1.738059] usb 9-3: skipped 2 descriptors after interface
[ 1.738061] usb 9-3: skipped 1 descriptor after endpoint
[ 1.741021] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 1.742039] usb 9-3: default language 0x0409
[ 1.765016] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 1.766036] usb 9-3: udev 2, busnum 9, minor = 1025
[ 1.766038] usb 9-3: New USB device found, idVendor=0471, idProduct=0311
[ 1.766244] usb 9-3: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[ 1.766448] usb 9-3: SerialNumber: 01680000EA164101
[ 1.766811] usb 9-3: usb_probe_device
[ 1.766813] usb 9-3: configuration #1 chosen from 1 choice
[ 1.767184] usb 9-3: Successful Endpoint Configure command
[ 1.769035] usb 9-3: adding 9-3:1.0 (config #1, interface 0)
[ 1.769151] usb 9-3: adding 9-3:1.1 (config #1, interface 1)
[ 1.769235] usb 9-3: adding 9-3:1.2 (config #1, interface 2)
[ 4.483174] pwc: Philips PCVC740K (ToUCam Pro)/PCVC840 (ToUCam II) USB webcam detected.
[ 4.515833] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 4.516894] pwc: Registered as video0.
[ 4.518834] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint
[ 4.520834] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint
[ 4.521051] Philips webcam 9-3:1.1: usb_probe_interface
[ 4.521053] Philips webcam 9-3:1.1: usb_probe_interface - got id
[ 4.521058] Philips webcam 9-3:1.2: usb_probe_interface
[ 4.521060] Philips webcam 9-3:1.2: usb_probe_interface - got id
[ 4.521073] usbcore: registered new interface driver Philips webcam
And when trying to actually grab pictures from the device:
[ 12.957593] usb 9-3: Successful Endpoint Configure command
[ 12.967542] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7ac74000, num_trbs = 10
[ 12.967553] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af8c000, num_trbs = 10
[ 12.985500] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
[ 20.946116] eth1: no IPv6 routers present
[ 40.029279] usb 9-3: Successful Endpoint Configure command
[ 40.039186] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a814000, num_trbs = 10
[ 40.039198] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b734000, num_trbs = 10
[ 40.057195] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
[ 40.216270] usb 9-3: Successful Endpoint Configure command
[ 40.226183] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a9c0000, num_trbs = 10
[ 40.226193] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a98c000, num_trbs = 10
[ 40.245183] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
[ 40.399261] usb 9-3: Successful Endpoint Configure command
[ 40.408210] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a9c0000, num_trbs = 10
[ 40.408220] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a98c000, num_trbs = 10
[ 47.145805] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
[ 48.076894] usb 9-3: Successful Endpoint Configure command
[ 48.086805] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b180000, num_trbs = 10
[ 48.086816] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b47c000, num_trbs = 10
[ 48.105803] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
[ 48.263885] usb 9-3: Successful Endpoint Configure command
[ 48.273796] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7bba0000, num_trbs = 10
[ 48.273807] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af6c000, num_trbs = 10
[ 48.292793] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
[ 48.446875] usb 9-3: Successful Endpoint Configure command
[ 48.456784] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7bba0000, num_trbs = 10
[ 48.456794] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af6c000, num_trbs = 10
[ 51.778648] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
Saturday, March 13, 2010, 12:25:38 AM, you wrote:
> On Fri, Mar 12, 2010 at 05:43:45PM +0100, Sander Eikelenboom wrote:
>> Hi Sarah,
>>
>> I'm trying to use an USB 1.1 device on a USB 3.0 host controller, but it doesn't seem to work (tested with kernel versions up to 2.6.34-rc1):
>> - with lsusb I can only see a usb 3.0 root hub (with a USB 2.0 host controller, i'am always seeing the roothubs for lower speeds as well, so maybe this is the problem ?)
>> - with lsusb I can see the usb 1.1 device connected to the USB 3.0 root hub.
>> - the driver from the usb 1.1 device get loaded, but it gives errors, and (it's a webcam) doesn't give video.
>> - the manufacturer claims it should be backwards compatible hardware.
>>
>> - Should this work with the current (expirimental) state of the xhci-hcd driver in linux ?
>>
>> The hardware is (asus U3S6):
>> 03:00.0 USB Controller [0c03]: NEC Corporation Device [1033:0194] (rev 03) (prog-if 30)
>> Subsystem: ASUSTeK Computer Inc. Device [1043:8413]
> From the log files, it looks like your usb 1.1 device is a webcam; is
> that correct?
>> [ 5.097306] pwc: Philips webcam module version 10.0.13 loaded.
>> [ 5.097507] pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
>> [ 5.097859] pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
>> [ 5.098215] pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
>> [ 5.098557] pwc: Trace options: 0x0001
>> [ 5.098576] Philips webcam 9-3:1.0: usb_probe_interface
>> [ 5.098578] Philips webcam 9-3:1.0: usb_probe_interface - got id
> ...
>> [ 13.116489] pwc: isoc_init() submit_urb 0 failed with error -22
> Webcams have isochronous endpoints, and the xHCI driver doesn't support
> isochronous transfers yet. There are patches to add isochronous
> support, but they're still under going review. They missed the 2.6.34
> merge window, so I'm not sure if they'll make it into 2.6.34 or 2.6.35.
> If you want to try them out, the latest versions of the patches are
> here:
> http://marc.info/?l=linux-usb&m=126838645617885&w=2
> http://marc.info/?l=linux-usb&m=126838648717923&w=2
> http://marc.info/?l=linux-usb&m=126838649217932&w=2
> Let me know if they work for you.
> Sarah Sharp
>> Bus 009 Device 002: ID 0471:0311 Philips PCVC740K ToUcam Pro [pwc]
>> Device Descriptor:
>> bLength 18
>> bDescriptorType 1
>> bcdUSB 1.10
>> bDeviceClass 0 (Defined at Interface level)
>> bDeviceSubClass 0
>> bDeviceProtocol 0
>> bMaxPacketSize0 8
>> idVendor 0x0471 Philips
>> idProduct 0x0311 PCVC740K ToUcam Pro [pwc]
>> bcdDevice 0.03
>> iManufacturer 0
>> iProduct 0
>> iSerial 1 01680000EA164101
>> bNumConfigurations 1
>> Configuration Descriptor:
>> bLength 9
>> bDescriptorType 2
>> wTotalLength 490
>> bNumInterfaces 3
>> bConfigurationValue 1
>> iConfiguration 0
>> bmAttributes 0xa0
>> (Bus Powered)
>> Remote Wakeup
>> MaxPower 500mA
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 0
>> bAlternateSetting 0
>> bNumEndpoints 2
>> bInterfaceClass 255 Vendor Specific Class
>> bInterfaceSubClass 0
>> bInterfaceProtocol 0
>> iInterface 0
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x82 EP 2 IN
>> bmAttributes 3
>> Transfer Type Interrupt
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0001 1x 1 bytes
>> bInterval 32
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x85 EP 5 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0000 1x 0 bytes
>> bInterval 1
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 0
>> bAlternateSetting 1
>> bNumEndpoints 2
>> bInterfaceClass 255 Vendor Specific Class
>> bInterfaceSubClass 0
>> bInterfaceProtocol 0
>> iInterface 0
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x82 EP 2 IN
>> bmAttributes 3
>> Transfer Type Interrupt
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0001 1x 1 bytes
>> bInterval 32
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x85 EP 5 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x00c4 1x 196 bytes
>> bInterval 1
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 0
>> bAlternateSetting 2
>> bNumEndpoints 2
>> bInterfaceClass 255 Vendor Specific Class
>> bInterfaceSubClass 0
>> bInterfaceProtocol 0
>> iInterface 0
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x82 EP 2 IN
>> bmAttributes 3
>> Transfer Type Interrupt
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0001 1x 1 bytes
>> bInterval 32
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x85 EP 5 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0124 1x 292 bytes
>> bInterval 1
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 0
>> bAlternateSetting 3
>> bNumEndpoints 2
>> bInterfaceClass 255 Vendor Specific Class
>> bInterfaceSubClass 0
>> bInterfaceProtocol 0
>> iInterface 0
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x82 EP 2 IN
>> bmAttributes 3
>> Transfer Type Interrupt
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0001 1x 1 bytes
>> bInterval 32
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x85 EP 5 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x01c0 1x 448 bytes
>> bInterval 1
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 0
>> bAlternateSetting 4
>> bNumEndpoints 2
>> bInterfaceClass 255 Vendor Specific Class
>> bInterfaceSubClass 0
>> bInterfaceProtocol 0
>> iInterface 0
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x82 EP 2 IN
>> bmAttributes 3
>> Transfer Type Interrupt
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0001 1x 1 bytes
>> bInterval 32
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x85 EP 5 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0250 1x 592 bytes
>> bInterval 1
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 0
>> bAlternateSetting 5
>> bNumEndpoints 2
>> bInterfaceClass 255 Vendor Specific Class
>> bInterfaceSubClass 0
>> bInterfaceProtocol 0
>> iInterface 0
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x82 EP 2 IN
>> bmAttributes 3
>> Transfer Type Interrupt
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0001 1x 1 bytes
>> bInterval 32
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x85 EP 5 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x02c0 1x 704 bytes
>> bInterval 1
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 0
>> bAlternateSetting 6
>> bNumEndpoints 2
>> bInterfaceClass 255 Vendor Specific Class
>> bInterfaceSubClass 0
>> bInterfaceProtocol 0
>> iInterface 0
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x82 EP 2 IN
>> bmAttributes 3
>> Transfer Type Interrupt
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0001 1x 1 bytes
>> bInterval 32
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x85 EP 5 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0308 1x 776 bytes
>> bInterval 1
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 0
>> bAlternateSetting 7
>> bNumEndpoints 2
>> bInterfaceClass 255 Vendor Specific Class
>> bInterfaceSubClass 0
>> bInterfaceProtocol 0
>> iInterface 0
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x82 EP 2 IN
>> bmAttributes 3
>> Transfer Type Interrupt
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0001 1x 1 bytes
>> bInterval 32
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x85 EP 5 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0348 1x 840 bytes
>> bInterval 1
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 0
>> bAlternateSetting 8
>> bNumEndpoints 2
>> bInterfaceClass 255 Vendor Specific Class
>> bInterfaceSubClass 0
>> bInterfaceProtocol 0
>> iInterface 0
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x82 EP 2 IN
>> bmAttributes 3
>> Transfer Type Interrupt
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0001 1x 1 bytes
>> bInterval 32
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x85 EP 5 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0380 1x 896 bytes
>> bInterval 1
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 0
>> bAlternateSetting 9
>> bNumEndpoints 2
>> bInterfaceClass 255 Vendor Specific Class
>> bInterfaceSubClass 0
>> bInterfaceProtocol 0
>> iInterface 0
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x82 EP 2 IN
>> bmAttributes 3
>> Transfer Type Interrupt
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0001 1x 1 bytes
>> bInterval 32
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x85 EP 5 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x03c0 1x 960 bytes
>> bInterval 1
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 0
>> bAlternateSetting 10
>> bNumEndpoints 2
>> bInterfaceClass 255 Vendor Specific Class
>> bInterfaceSubClass 0
>> bInterfaceProtocol 0
>> iInterface 0
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x82 EP 2 IN
>> bmAttributes 3
>> Transfer Type Interrupt
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0001 1x 1 bytes
>> bInterval 32
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x85 EP 5 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x03c0 1x 960 bytes
>> bInterval 1
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 1
>> bAlternateSetting 0
>> bNumEndpoints 0
>> bInterfaceClass 1 Audio
>> bInterfaceSubClass 1 Control Device
>> bInterfaceProtocol 0
>> iInterface 0
>> AudioControl Interface Descriptor:
>> bLength 9
>> bDescriptorType 36
>> bDescriptorSubtype 1 (HEADER)
>> bcdADC 1.00
>> wTotalLength 38
>> bInCollection 1
>> baInterfaceNr( 0) 2
>> AudioControl Interface Descriptor:
>> bLength 12
>> bDescriptorType 36
>> bDescriptorSubtype 2 (INPUT_TERMINAL)
>> bTerminalID 1
>> wTerminalType 0x0201 Microphone
>> bAssocTerminal 0
>> bNrChannels 1
>> wChannelConfig 0x0000
>> iChannelNames 0
>> iTerminal 0
>> AudioControl Interface Descriptor:
>> bLength 8
>> bDescriptorType 36
>> bDescriptorSubtype 6 (FEATURE_UNIT)
>> bUnitID 2
>> bSourceID 1
>> bControlSize 1
>> bmaControls( 0) 0x03
>> Mute
>> Volume
>> iFeature 0
>> AudioControl Interface Descriptor:
>> bLength 9
>> bDescriptorType 36
>> bDescriptorSubtype 3 (OUTPUT_TERMINAL)
>> bTerminalID 3
>> wTerminalType 0x0101 USB Streaming
>> bAssocTerminal 0
>> bSourceID 2
>> iTerminal 0
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 2
>> bAlternateSetting 0
>> bNumEndpoints 0
>> bInterfaceClass 1 Audio
>> bInterfaceSubClass 2 Streaming
>> bInterfaceProtocol 0
>> iInterface 0
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 2
>> bAlternateSetting 1
>> bNumEndpoints 1
>> bInterfaceClass 1 Audio
>> bInterfaceSubClass 2 Streaming
>> bInterfaceProtocol 0
>> iInterface 0
>> AudioStreaming Interface Descriptor:
>> bLength 7
>> bDescriptorType 36
>> bDescriptorSubtype 1 (AS_GENERAL)
>> bTerminalLink 3
>> bDelay 1 frames
>> wFormatTag 1 PCM
>> AudioStreaming Interface Descriptor:
>> bLength 11
>> bDescriptorType 36
>> bDescriptorSubtype 2 (FORMAT_TYPE)
>> bFormatType 1 (FORMAT_TYPE_I)
>> bNrChannels 1
>> bSubframeSize 2
>> bBitResolution 16
>> bSamFreqType 1 Discrete
>> tSamFreq[ 0] 44100
>> Endpoint Descriptor:
>> bLength 9
>> bDescriptorType 5
>> bEndpointAddress 0x84 EP 4 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x005a 1x 90 bytes
>> bInterval 1
>> bRefresh 0
>> bSynchAddress 0
>> AudioControl Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 37
>> bDescriptorSubtype 1 (EP_GENERAL)
>> bmAttributes 0x00
>> bLockDelayUnits 0 Undefined
>> wLockDelay 0 Undefined
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 2
>> bAlternateSetting 2
>> bNumEndpoints 1
>> bInterfaceClass 1 Audio
>> bInterfaceSubClass 2 Streaming
>> bInterfaceProtocol 0
>> iInterface 0
>> AudioStreaming Interface Descriptor:
>> bLength 7
>> bDescriptorType 36
>> bDescriptorSubtype 1 (AS_GENERAL)
>> bTerminalLink 3
>> bDelay 1 frames
>> wFormatTag 1 PCM
>> AudioStreaming Interface Descriptor:
>> bLength 11
>> bDescriptorType 36
>> bDescriptorSubtype 2 (FORMAT_TYPE)
>> bFormatType 1 (FORMAT_TYPE_I)
>> bNrChannels 1
>> bSubframeSize 2
>> bBitResolution 16
>> bSamFreqType 1 Discrete
>> tSamFreq[ 0] 22050
>> Endpoint Descriptor:
>> bLength 9
>> bDescriptorType 5
>> bEndpointAddress 0x84 EP 4 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x002e 1x 46 bytes
>> bInterval 1
>> bRefresh 0
>> bSynchAddress 0
>> AudioControl Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 37
>> bDescriptorSubtype 1 (EP_GENERAL)
>> bmAttributes 0x00
>> bLockDelayUnits 0 Undefined
>> wLockDelay 0 Undefined
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 2
>> bAlternateSetting 3
>> bNumEndpoints 1
>> bInterfaceClass 1 Audio
>> bInterfaceSubClass 2 Streaming
>> bInterfaceProtocol 0
>> iInterface 0
>> AudioStreaming Interface Descriptor:
>> bLength 7
>> bDescriptorType 36
>> bDescriptorSubtype 1 (AS_GENERAL)
>> bTerminalLink 3
>> bDelay 1 frames
>> wFormatTag 1 PCM
>> AudioStreaming Interface Descriptor:
>> bLength 11
>> bDescriptorType 36
>> bDescriptorSubtype 2 (FORMAT_TYPE)
>> bFormatType 1 (FORMAT_TYPE_I)
>> bNrChannels 1
>> bSubframeSize 2
>> bBitResolution 16
>> bSamFreqType 1 Discrete
>> tSamFreq[ 0] 11025
>> Endpoint Descriptor:
>> bLength 9
>> bDescriptorType 5
>> bEndpointAddress 0x84 EP 4 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0019 1x 25 bytes
>> bInterval 1
>> bRefresh 0
>> bSynchAddress 0
>> AudioControl Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 37
>> bDescriptorSubtype 1 (EP_GENERAL)
>> bmAttributes 0x00
>> bLockDelayUnits 0 Undefined
>> wLockDelay 0 Undefined
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 2
>> bAlternateSetting 4
>> bNumEndpoints 1
>> bInterfaceClass 1 Audio
>> bInterfaceSubClass 2 Streaming
>> bInterfaceProtocol 0
>> iInterface 0
>> AudioStreaming Interface Descriptor:
>> bLength 7
>> bDescriptorType 36
>> bDescriptorSubtype 1 (AS_GENERAL)
>> bTerminalLink 3
>> bDelay 1 frames
>> wFormatTag 1 PCM
>> AudioStreaming Interface Descriptor:
>> bLength 11
>> bDescriptorType 36
>> bDescriptorSubtype 2 (FORMAT_TYPE)
>> bFormatType 1 (FORMAT_TYPE_I)
>> bNrChannels 1
>> bSubframeSize 2
>> bBitResolution 16
>> bSamFreqType 1 Discrete
>> tSamFreq[ 0] 8000
>> Endpoint Descriptor:
>> bLength 9
>> bDescriptorType 5
>> bEndpointAddress 0x84 EP 4 IN
>> bmAttributes 1
>> Transfer Type Isochronous
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0010 1x 16 bytes
>> bInterval 1
>> bRefresh 0
>> bSynchAddress 0
>> AudioControl Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 37
>> bDescriptorSubtype 1 (EP_GENERAL)
>> bmAttributes 0x00
>> bLockDelayUnits 0 Undefined
>> wLockDelay 0 Undefined
>> Device Status: 0x0002
>> (Bus Powered)
>> Remote Wakeup Enabled
>>
>> Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
>> Device Descriptor:
>> bLength 18
>> bDescriptorType 1
>> bcdUSB 3.00
>> bDeviceClass 9 Hub
>> bDeviceSubClass 0 Unused
>> bDeviceProtocol 3
>> bMaxPacketSize0 9
>> idVendor 0x1d6b Linux Foundation
>> idProduct 0x0003 3.0 root hub
>> bcdDevice 2.06
>> iManufacturer 3 Linux 2.6.34-rc1 xhci_hcd
>> iProduct 2 xHCI Host Controller
>> iSerial 1 0000:03:00.0
>> bNumConfigurations 1
>> Configuration Descriptor:
>> bLength 9
>> bDescriptorType 2
>> wTotalLength 25
>> bNumInterfaces 1
>> bConfigurationValue 1
>> iConfiguration 0
>> bmAttributes 0xe0
>> Self Powered
>> Remote Wakeup
>> MaxPower 0mA
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 0
>> bAlternateSetting 0
>> bNumEndpoints 1
>> bInterfaceClass 9 Hub
>> bInterfaceSubClass 0 Unused
>> bInterfaceProtocol 0 Full speed (or root) hub
>> iInterface 0
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x81 EP 1 IN
>> bmAttributes 3
>> Transfer Type Interrupt
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0004 1x 4 bytes
>> bInterval 12
>> Hub Descriptor:
>> bLength 9
>> bDescriptorType 41
>> nNbrPorts 4
>> wHubCharacteristic 0x0009
>> Per-port power switching
>> Per-port overcurrent protection
>> TT think time 8 FS bits
>> bPwrOn2PwrGood 10 * 2 milli seconds
>> bHubContrCurrent 0 milli Ampere
>> DeviceRemovable 0x00
>> PortPwrCtrlMask 0xff
>> Hub Port Status:
>> Port 1: 0000.0100 power
>> Port 2: 0000.0100 power
>> Port 3: 0000.0103 power enable connect
>> Port 4: 0000.0100 power
>> Device Status: 0x0003
>> Self Powered
>> Remote Wakeup Enabled
--
Best regards,
Sander mailto:linux@eikelenboom.it
[-- Attachment #2: dmesg-with-patch.txt --]
[-- Type: text/plain, Size: 74005 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.34-rc1 (root@xentest) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #3 SMP Sat Mar 13 03:51:02 CET 2010
[ 0.000000] Command line: root=/dev/sda1 ro console=tty0
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[ 0.000000] BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007cb70000 (usable)
[ 0.000000] BIOS-e820: 000000007cb70000 - 000000007cb7e000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007cb7e000 - 000000007cbd0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007cbd0000 - 000000007cc00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed01100 (reserved)
[ 0.000000] BIOS-e820: 00000000fed02000 - 00000000fed14c00 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed40000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI present.
[ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x7cb70 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CBFFF write-protect
[ 0.000000] CC000-DFFFF uncachable
[ 0.000000] E0000-EFFFF write-through
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07CC00000 mask FFFC00000 uncachable
[ 0.000000] 2 base 07D000000 mask FFF000000 uncachable
[ 0.000000] 3 base 07E000000 mask FFE000000 uncachable
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
[ 0.000000] modified: 0000000000010000 - 000000000009f400 (usable)
[ 0.000000] modified: 000000000009f400 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 000000007cb70000 (usable)
[ 0.000000] modified: 000000007cb70000 - 000000007cb7e000 (ACPI data)
[ 0.000000] modified: 000000007cb7e000 - 000000007cbd0000 (ACPI NVS)
[ 0.000000] modified: 000000007cbd0000 - 000000007cc00000 (reserved)
[ 0.000000] modified: 00000000fed00000 - 00000000fed01100 (reserved)
[ 0.000000] modified: 00000000fed02000 - 00000000fed14c00 (reserved)
[ 0.000000] modified: 00000000fed20000 - 00000000fed40000 (reserved)
[ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] modified: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780
[ 0.000000] init_memory_mapping: 0000000000000000-000000007cb70000
[ 0.000000] 0000000000 - 007ca00000 page 2M
[ 0.000000] 007ca00000 - 007cb70000 page 4k
[ 0.000000] kernel direct mapping tables up to 7cb70000 @ 16000-1a000
[ 0.000000] RAMDISK: 37ce4000 - 37fef0f8
[ 0.000000] ACPI: RSDP 00000000000fb080 00024 (v02 ACPIAM)
[ 0.000000] ACPI: XSDT 000000007cb70100 00064 (v01 A_M_I_ OEMXSDT 05000927 MSFT 00000097)
[ 0.000000] ACPI: FACP 000000007cb70290 000F4 (v03 A_M_I_ OEMFACP 05000927 MSFT 00000097)
[ 0.000000] ACPI: DSDT 000000007cb70440 0841F (v01 A1065 A1065000 00000000 INTL 20060113)
[ 0.000000] ACPI: FACS 000000007cb7e000 00040
[ 0.000000] ACPI: APIC 000000007cb70390 0006C (v01 A_M_I_ OEMAPIC 05000927 MSFT 00000097)
[ 0.000000] ACPI: MCFG 000000007cb70400 0003C (v01 A_M_I_ OEMMCFG 05000927 MSFT 00000097)
[ 0.000000] ACPI: OEMB 000000007cb7e040 00089 (v01 A_M_I_ AMI_OEM 05000927 MSFT 00000097)
[ 0.000000] ACPI: HPET 000000007cb78860 00038 (v01 A_M_I_ OEMHPET 05000927 MSFT 00000097)
[ 0.000000] ACPI: GSCI 000000007cb7e0d0 02024 (v01 A_M_I_ GMCHSCI 05000927 MSFT 00000097)
[ 0.000000] ACPI: DMAR 000000007cb80100 00158 (v01 AMI OEMDMAR 00000001 MSFT 00000097)
[ 0.000000] ACPI: SSDT 000000007cb811d0 00A7C (v01 DpgPmm CpuPm 00000012 INTL 20060113)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007cb70
[ 0.000000] On node 0 totalpages: 510719
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3927 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 6929 pages used for memmap
[ 0.000000] DMA32 zone: 499807 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] early_res array is doubled to 64 at [18000 - 187ff]
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 7cc00000 (gap: 7cc00000:82100000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff880002000000 s87784 r8192 d22808 u524288
[ 0.000000] pcpu-alloc: s87784 r8192 d22808 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 503734
[ 0.000000] Kernel command line: root=/dev/sda1 ro console=tty0
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Subtract (51 early reservations)
[ 0.000000] #1 [0001000000 - 0001e9f494] TEXT DATA BSS
[ 0.000000] #2 [0037ce4000 - 0037fef0f8] RAMDISK
[ 0.000000] #3 [0001ea0000 - 0001ea0298] BRK
[ 0.000000] #4 [00000ff790 - 0000100000] BIOS reserved
[ 0.000000] #5 [00000ff780 - 00000ff790] MP-table mpf
[ 0.000000] #6 [000009f400 - 00000e3da0] BIOS reserved
[ 0.000000] #7 [00000e3f84 - 00000ff780] BIOS reserved
[ 0.000000] #8 [00000e3da0 - 00000e3f84] MP-table mpc
[ 0.000000] #9 [0000010000 - 0000012000] TRAMPOLINE
[ 0.000000] #10 [0000012000 - 0000016000] ACPI WAKEUP
[ 0.000000] #11 [0000016000 - 0000018000] PGTABLE
[ 0.000000] #12 [0001ea02c0 - 0001ea12c0] BOOTMEM
[ 0.000000] #13 [0001e9f4c0 - 0001e9f640] BOOTMEM
[ 0.000000] #14 [00026a2000 - 00042a2000] BOOTMEM
[ 0.000000] #15 [0001e9f640 - 0001e9f7c0] BOOTMEM
[ 0.000000] #16 [0001ea12c0 - 0001ead2c0] BOOTMEM
[ 0.000000] #17 [0001eae000 - 0001eaf000] BOOTMEM
[ 0.000000] #18 [0001e9f7c0 - 0001e9f801] BOOTMEM
[ 0.000000] #19 [0001e9f840 - 0001e9f883] BOOTMEM
[ 0.000000] #20 [0001e9f8c0 - 0001e9fb98] BOOTMEM
[ 0.000000] #21 [0001e9fbc0 - 0001e9fc28] BOOTMEM
[ 0.000000] #22 [0001e9fc40 - 0001e9fca8] BOOTMEM
[ 0.000000] #23 [0001e9fcc0 - 0001e9fd28] BOOTMEM
[ 0.000000] #24 [0001e9fd40 - 0001e9fda8] BOOTMEM
[ 0.000000] #25 [0001e9fdc0 - 0001e9fe28] BOOTMEM
[ 0.000000] #26 [0001e9fe40 - 0001e9fea8] BOOTMEM
[ 0.000000] #27 [0001e9fec0 - 0001e9ff28] BOOTMEM
[ 0.000000] #28 [0001e9ff40 - 0001e9ffa8] BOOTMEM
[ 0.000000] #29 [0001ead2c0 - 0001ead328] BOOTMEM
[ 0.000000] #30 [0001ead340 - 0001ead3a8] BOOTMEM
[ 0.000000] #31 [0001ead3c0 - 0001ead428] BOOTMEM
[ 0.000000] #32 [0001ead440 - 0001ead4a8] BOOTMEM
[ 0.000000] #33 [0001e9ffc0 - 0001e9ffe0] BOOTMEM
[ 0.000000] #34 [0001ead4c0 - 0001ead4df] BOOTMEM
[ 0.000000] #35 [0001ead500 - 0001ead51f] BOOTMEM
[ 0.000000] #36 [0002000000 - 000201d000] BOOTMEM
[ 0.000000] #37 [0002080000 - 000209d000] BOOTMEM
[ 0.000000] #38 [0002100000 - 000211d000] BOOTMEM
[ 0.000000] #39 [0002180000 - 000219d000] BOOTMEM
[ 0.000000] #40 [0001ead540 - 0001ead548] BOOTMEM
[ 0.000000] #41 [0001ead580 - 0001ead588] BOOTMEM
[ 0.000000] #42 [0001ead5c0 - 0001ead5d0] BOOTMEM
[ 0.000000] #43 [0001ead600 - 0001ead620] BOOTMEM
[ 0.000000] #44 [0001ead640 - 0001ead770] BOOTMEM
[ 0.000000] #45 [0001ead780 - 0001ead7d0] BOOTMEM
[ 0.000000] #46 [0001ead800 - 0001ead850] BOOTMEM
[ 0.000000] #47 [0001eaf000 - 0001eb7000] BOOTMEM
[ 0.000000] #48 [000219d000 - 000239d000] BOOTMEM
[ 0.000000] #49 [0001eb7000 - 0001fb7000] BOOTMEM
[ 0.000000] #50 [0001ead880 - 0001eadac0] BOOTMEM
[ 0.000000] 18 40 - 80 9f
[ 0.000000] 100 100 - 1000 1000
[ 0.000000] 1fb7 1fc0 - 2000 2000
[ 0.000000] 201d 2040 - 2080 2080
[ 0.000000] 209d 20c0 - 2100 2100
[ 0.000000] 211d 2140 - 2180 2180
[ 0.000000] 239d 23c0 - 2680 26a2
[ 0.000000] 42a2 42c0 - 37cc0 37ce4
[ 0.000000] 37ff0 38000 - 7cb40 7cb70
[ 0.000000] Memory: 1992448k/2043328k available (6396k kernel code, 452k absent, 50428k reserved, 6896k data, 564k init)
[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:4352 nr_irqs:440
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2666.771 MHz processor.
[ 0.002004] Calibrating delay loop (skipped), value calculated using timer frequency.. 5333.54 BogoMIPS (lpj=2666771)
[ 0.002392] Security Framework initialized
[ 0.002578] SELinux: Initializing.
[ 0.002766] SELinux: Starting in permissive mode
[ 0.002773] Mount-cache hash table entries: 256
[ 0.003120] Initializing cgroup subsys ns
[ 0.003300] Initializing cgroup subsys cpuacct
[ 0.003480] Initializing cgroup subsys freezer
[ 0.003676] CPU: Physical Processor ID: 0
[ 0.003853] CPU: Processor Core ID: 0
[ 0.004003] mce: CPU supports 6 MCE banks
[ 0.004185] using mwait in idle threads.
[ 0.004362] Performance Events: Core2 events, Intel PMU driver.
[ 0.004608] ... version: 2
[ 0.004791] ... bit width: 40
[ 0.005001] ... generic registers: 2
[ 0.005183] ... value mask: 000000ffffffffff
[ 0.005368] ... max period: 000000007fffffff
[ 0.005554] ... fixed-purpose events: 3
[ 0.005743] ... event mask: 0000000700000003
[ 0.006911] ACPI: Core revision 20100121
[ 0.017357] Setting APIC routing to flat
[ 0.017834] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.028026] CPU0: Intel(R) Core(TM)2 Quad CPU Q9400 @ 2.66GHz stepping 0a
[ 0.028999] Booting Node 0, Processors #1 #2 #3 Ok.
[ 0.245005] Brought up 4 CPUs
[ 0.245203] Total of 4 processors activated (21331.12 BogoMIPS).
[ 0.247082] Time: 2:54:15 Date: 03/13/10
[ 0.248041] NET: Registered protocol family 16
[ 0.248246] ACPI: bus type pci registered
[ 0.249036] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.249366] PCI: not using MMCONFIG
[ 0.249549] PCI: Using configuration type 1 for base access
[ 0.266048] bio: create slab <bio-0> at 0
[ 0.267449] ACPI: EC: Look up EC in DSDT
[ 0.268669] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.275623] ACPI: Interpreter enabled
[ 0.275812] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.277003] ACPI: Using IOAPIC for interrupt routing
[ 0.277238] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.278390] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[ 0.307076] ACPI Warning: Incorrect checksum in table [OEMB] - C5, should be BC (20100121/tbutils-314)
[ 0.308150] ACPI: No dock devices found.
[ 0.308338] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.308801] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.309238] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.309427] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.309616] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.310002] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000dffff]
[ 0.310337] pci_root PNP0A08:00: host bridge window [mem 0x7cc00000-0xdfffffff]
[ 0.310675] pci_root PNP0A08:00: host bridge window [mem 0xf0000000-0xffffffff]
[ 0.311052] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.311055] pci 0000:00:01.0: PME# disabled
[ 0.311071] pci 0000:00:02.0: reg 10: [mem 0xfe000000-0xfe3fffff 64bit]
[ 0.311076] pci 0000:00:02.0: reg 18: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.311079] pci 0000:00:02.0: reg 20: [io 0xbc00-0xbc07]
[ 0.311127] pci 0000:00:03.0: reg 10: [mem 0xfe6fb000-0xfe6fb00f 64bit]
[ 0.311181] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
[ 0.311185] pci 0000:00:03.0: PME# disabled
[ 0.311232] pci 0000:00:19.0: reg 10: [mem 0xfe6c0000-0xfe6dffff]
[ 0.311237] pci 0000:00:19.0: reg 14: [mem 0xfe6fa000-0xfe6fafff]
[ 0.311242] pci 0000:00:19.0: reg 18: [io 0xb880-0xb89f]
[ 0.311273] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.311276] pci 0000:00:19.0: PME# disabled
[ 0.311314] pci 0000:00:1a.0: reg 20: [io 0xb400-0xb41f]
[ 0.311366] pci 0000:00:1a.1: reg 20: [io 0xb480-0xb49f]
[ 0.311418] pci 0000:00:1a.2: reg 20: [io 0xb800-0xb81f]
[ 0.311469] pci 0000:00:1a.7: reg 10: [mem 0xfe6f9000-0xfe6f93ff]
[ 0.311514] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.311518] pci 0000:00:1a.7: PME# disabled
[ 0.311545] pci 0000:00:1b.0: reg 10: [mem 0xfe6f0000-0xfe6f3fff 64bit]
[ 0.311578] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.311581] pci 0000:00:1b.0: PME# disabled
[ 0.311630] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.311633] pci 0000:00:1c.0: PME# disabled
[ 0.311687] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.311690] pci 0000:00:1c.4: PME# disabled
[ 0.311739] pci 0000:00:1d.0: reg 20: [io 0xac00-0xac1f]
[ 0.311801] pci 0000:00:1d.1: reg 20: [io 0xb000-0xb01f]
[ 0.311853] pci 0000:00:1d.2: reg 20: [io 0xb080-0xb09f]
[ 0.311905] pci 0000:00:1d.7: reg 10: [mem 0xfe6f8000-0xfe6f83ff]
[ 0.312033] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.312037] pci 0000:00:1d.7: PME# disabled
[ 0.312163] pci 0000:00:1f.2: reg 10: [io 0x0000-0x0007]
[ 0.312168] pci 0000:00:1f.2: reg 14: [io 0x0000-0x0003]
[ 0.312172] pci 0000:00:1f.2: reg 18: [io 0x0000-0x0007]
[ 0.312176] pci 0000:00:1f.2: reg 1c: [io 0x0000-0x0003]
[ 0.312181] pci 0000:00:1f.2: reg 20: [io 0xff90-0xff9f]
[ 0.312185] pci 0000:00:1f.2: reg 24: [io 0xffa0-0xffaf]
[ 0.312221] pci 0000:00:1f.3: reg 10: [mem 0xfe6ef000-0xfe6ef0ff 64bit]
[ 0.312232] pci 0000:00:1f.3: reg 20: [io 0x0400-0x041f]
[ 0.312262] pci 0000:00:1f.5: reg 10: [io 0xa880-0xa887]
[ 0.312266] pci 0000:00:1f.5: reg 14: [io 0xa800-0xa803]
[ 0.312271] pci 0000:00:1f.5: reg 18: [io 0xa480-0xa487]
[ 0.312275] pci 0000:00:1f.5: reg 1c: [io 0xa400-0xa403]
[ 0.312279] pci 0000:00:1f.5: reg 20: [io 0xa080-0xa08f]
[ 0.312284] pci 0000:00:1f.5: reg 24: [io 0xa000-0xa00f]
[ 0.312340] pci 0000:01:00.0: reg 10: [mem 0xfe7e0000-0xfe7fffff]
[ 0.312371] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.312374] pci 0000:01:00.0: PME# disabled
[ 0.312386] pci 0000:00:01.0: PCI bridge to [bus 01-04]
[ 0.312571] pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
[ 0.312573] pci 0000:00:01.0: bridge window [mem 0xfe700000-0xfe9fffff]
[ 0.312576] pci 0000:00:01.0: bridge window [mem 0xfff00000 - 000fffff pref] reg reading
[ 0.312653] pci 0000:02:01.0: PME# supported from D0 D3hot D3cold
[ 0.312656] pci 0000:02:01.0: PME# disabled
[ 0.312708] pci 0000:02:02.0: PME# supported from D0 D3hot D3cold
[ 0.312711] pci 0000:02:02.0: PME# disabled
[ 0.312741] pci 0000:01:00.0: PCI bridge to [bus 02-04]
[ 0.312948] pci 0000:01:00.0: bridge window [io 0xc000-0xcfff]
[ 0.312951] pci 0000:01:00.0: bridge window [mem 0xfe800000-0xfe9fffff]
[ 0.312955] pci 0000:01:00.0: bridge window [mem 0xfff00000 - 000fffff pref] reg reading
[ 0.313022] pci 0000:03:00.0: reg 10: [mem 0xfe8fe000-0xfe8fffff 64bit]
[ 0.313078] pci 0000:03:00.0: PME# supported from D0 D3hot
[ 0.313082] pci 0000:03:00.0: PME# disabled
[ 0.313098] pci 0000:02:01.0: PCI bridge to [bus 03-03]
[ 0.313287] pci 0000:02:01.0: bridge window [io f000 - 0000] reg reading
[ 0.313290] pci 0000:02:01.0: bridge window [mem 0xfe800000-0xfe8fffff]
[ 0.313295] pci 0000:02:01.0: bridge window [mem 0xfff00000 - 000fffff pref] reg reading
[ 0.313347] pci 0000:04:00.0: reg 10: [io 0xcc00-0xcc07]
[ 0.313353] pci 0000:04:00.0: reg 14: [io 0xc880-0xc883]
[ 0.313358] pci 0000:04:00.0: reg 18: [io 0xc800-0xc807]
[ 0.313364] pci 0000:04:00.0: reg 1c: [io 0xc480-0xc483]
[ 0.313369] pci 0000:04:00.0: reg 20: [io 0xc400-0xc40f]
[ 0.313375] pci 0000:04:00.0: reg 24: [mem 0xfe9ff800-0xfe9fffff]
[ 0.313381] pci 0000:04:00.0: reg 30: [mem 0xfe9e0000-0xfe9effff pref]
[ 0.313404] pci 0000:04:00.0: PME# supported from D3hot
[ 0.313407] pci 0000:04:00.0: PME# disabled
[ 0.313418] pci 0000:02:02.0: PCI bridge to [bus 04-04]
[ 0.313607] pci 0000:02:02.0: bridge window [io 0xc000-0xcfff]
[ 0.313610] pci 0000:02:02.0: bridge window [mem 0xfe900000-0xfe9fffff]
[ 0.313615] pci 0000:02:02.0: bridge window [mem 0xfff00000 - 000fffff pref] reg reading
[ 0.313657] pci 0000:00:1c.0: PCI bridge to [bus 06-06]
[ 0.313863] pci 0000:00:1c.0: bridge window [io f000 - 0000] reg reading
[ 0.313866] pci 0000:00:1c.0: bridge window [mem 0xfff00000 - 0x000fffff] reg reading
[ 0.313871] pci 0000:00:1c.0: bridge window [mem 0xfd700000-0xfd7fffff 64bit pref]
[ 0.313925] pci 0000:05:00.0: reg 10: [io 0xdc00-0xdc07]
[ 0.313932] pci 0000:05:00.0: reg 14: [io 0xd880-0xd883]
[ 0.313939] pci 0000:05:00.0: reg 18: [io 0xd800-0xd807]
[ 0.313945] pci 0000:05:00.0: reg 1c: [io 0xd480-0xd483]
[ 0.313952] pci 0000:05:00.0: reg 20: [io 0xd400-0xd40f]
[ 0.313959] pci 0000:05:00.0: reg 24: [mem 0xfeaff000-0xfeaff1ff]
[ 0.313994] pci 0000:05:00.0: supports D1
[ 0.313995] pci 0000:05:00.0: PME# supported from D0 D1 D3hot
[ 0.314002] pci 0000:05:00.0: PME# disabled
[ 0.314015] pci 0000:00:1c.4: PCI bridge to [bus 05-05]
[ 0.314202] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
[ 0.314205] pci 0000:00:1c.4: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.314210] pci 0000:00:1c.4: bridge window [mem 0xfff00000 - 000fffff pref] reg reading
[ 0.314246] pci 0000:07:00.0: reg 10: [mem 0xfd800000-0xfdffffff pref]
[ 0.314251] pci 0000:07:00.0: reg 14: [mem 0xfebf0000-0xfebfffff]
[ 0.314257] pci 0000:07:00.0: reg 18: [io 0xec00-0xec7f]
[ 0.314275] pci 0000:07:00.0: reg 30: [mem 0xfebe0000-0xfebeffff pref]
[ 0.314290] pci 0000:07:00.0: supports D2
[ 0.314316] pci 0000:07:03.0: reg 10: [mem 0xfebdf000-0xfebdffff]
[ 0.314354] pci 0000:07:03.0: supports D1 D2
[ 0.314355] pci 0000:07:03.0: PME# supported from D0 D1 D2 D3hot
[ 0.314359] pci 0000:07:03.0: PME# disabled
[ 0.314394] pci 0000:00:1e.0: PCI bridge to [bus 07-07] (subtractive decode)
[ 0.314579] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
[ 0.314582] pci 0000:00:1e.0: bridge window [mem 0xfeb00000-0xfebfffff]
[ 0.314587] pci 0000:00:1e.0: bridge window [mem 0xfd800000-0xfdffffff 64bit pref]
[ 0.314589] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.314591] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.314593] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.314595] pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
[ 0.314597] pci 0000:00:1e.0: bridge window [mem 0x7cc00000-0xdfffffff] (subtractive decode)
[ 0.314599] pci 0000:00:1e.0: bridge window [mem 0xf0000000-0xffffffff] (subtractive decode)
[ 0.314612] pci_bus 0000:00: on NUMA node 0
[ 0.314616] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.314760] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.314846] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.314903] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[ 0.314983] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[ 0.335078] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.335567] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.336091] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.336744] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.337512] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 0.338090] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[ 0.338746] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.339475] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.340040] vgaarb: device added: PCI:0000:07:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.340381] vgaarb: loaded
[ 0.341026] SCSI subsystem initialized
[ 0.341202] libata version 3.00 loaded.
[ 0.342048] usbcore: registered new interface driver usbfs
[ 0.342048] usbcore: registered new interface driver hub
[ 0.342200] usbcore: registered new device driver usb
[ 0.343025] Advanced Linux Sound Architecture Driver Version 1.0.22.1.
[ 0.343205] PCI: Using ACPI for IRQ routing
[ 0.343389] PCI: pci_cache_line_size set to 64 bytes
[ 0.343494] reserve RAM buffer: 000000000009f400 - 000000000009ffff
[ 0.343496] reserve RAM buffer: 000000007cb70000 - 000000007fffffff
[ 0.344042] cfg80211: Calling CRDA to update world regulatory domain
[ 0.344042] NetLabel: Initializing
[ 0.344179] NetLabel: domain hash size = 128
[ 0.344376] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.344564] NetLabel: unlabeled traffic allowed by default
[ 0.345050] alloc irq_desc for 24 on node 0
[ 0.345051] alloc kstat_irqs on node 0
[ 0.345057] alloc irq_desc for 25 on node 0
[ 0.345058] alloc kstat_irqs on node 0
[ 0.345062] alloc irq_desc for 26 on node 0
[ 0.345063] alloc kstat_irqs on node 0
[ 0.345067] alloc irq_desc for 27 on node 0
[ 0.345068] alloc kstat_irqs on node 0
[ 0.345070] HPET: 8 timers in total, 4 timers will be used for per-cpu timer
[ 0.345265] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 24, 25, 26, 27, 0, 0
[ 0.345745] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.349020] hpet: hpet2 irq 24 for MSI
[ 0.350017] hpet: hpet3 irq 25 for MSI
[ 0.414020] hpet: hpet4 irq 26 for MSI
[ 0.552025] hpet: hpet5 irq 27 for MSI
[ 0.557003] Switching to clocksource tsc
[ 0.570723] pnp: PnP ACPI init
[ 0.570867] ACPI: bus type pnp registered
[ 0.574969] pnp: PnP ACPI: found 18 devices
[ 0.575172] ACPI: ACPI bus type pnp unregistered
[ 0.575363] system 00:01: [mem 0xfed14000-0xfed19fff] could not be reserved
[ 0.575553] system 00:01: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.575746] system 00:07: [io 0x0290-0x029f] has been reserved
[ 0.575936] system 00:08: [io 0x04d0-0x04d1] has been reserved
[ 0.576145] system 00:08: [io 0x0800-0x087f] has been reserved
[ 0.576327] system 00:08: [io 0x0500-0x057f] has been reserved
[ 0.576510] system 00:08: [mem 0xfed08000-0xfed08fff] has been reserved
[ 0.576693] system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.576877] system 00:08: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.577081] system 00:08: [mem 0xfed50000-0xfed8ffff] has been reserved
[ 0.577268] system 00:0b: [mem 0xffc00000-0xffdfffff] has been reserved
[ 0.577454] system 00:0d: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.577638] system 00:0d: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.577826] system 00:10: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.578036] system 00:11: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.578226] system 00:11: [mem 0x000c0000-0x000cffff] has been reserved
[ 0.578417] system 00:11: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.578607] system 00:11: [mem 0x00100000-0x7cbfffff] could not be reserved
[ 0.578801] system 00:11: [mem 0xe0000000-0xffffffff] could not be reserved
[ 0.584256] PCI: max bus depth: 3 pci_try_num: 4
[ 0.584293] pci 0000:02:01.0: PCI bridge to [bus 03-03]
[ 0.584480] pci 0000:02:01.0: bridge window [io disabled]
[ 0.584669] pci 0000:02:01.0: bridge window [mem 0xfe800000-0xfe8fffff]
[ 0.584860] pci 0000:02:01.0: bridge window [mem pref disabled]
[ 0.585073] pci 0000:02:02.0: PCI bridge to [bus 04-04]
[ 0.585265] pci 0000:02:02.0: bridge window [io 0xc000-0xcfff]
[ 0.585458] pci 0000:02:02.0: bridge window [mem 0xfe900000-0xfe9fffff]
[ 0.585649] pci 0000:02:02.0: bridge window [mem pref disabled]
[ 0.585839] pci 0000:01:00.0: PCI bridge to [bus 02-04]
[ 0.586044] pci 0000:01:00.0: bridge window [io 0xc000-0xcfff]
[ 0.586234] pci 0000:01:00.0: bridge window [mem 0xfe800000-0xfe9fffff]
[ 0.586425] pci 0000:01:00.0: bridge window [mem pref disabled]
[ 0.586621] pci 0000:00:01.0: PCI bridge to [bus 01-04]
[ 0.586809] pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
[ 0.587009] pci 0000:00:01.0: bridge window [mem 0xfe700000-0xfe9fffff]
[ 0.587205] pci 0000:00:01.0: bridge window [mem pref disabled]
[ 0.587395] pci 0000:00:1c.0: PCI bridge to [bus 06-06]
[ 0.587581] pci 0000:00:1c.0: bridge window [io disabled]
[ 0.587770] pci 0000:00:1c.0: bridge window [mem disabled]
[ 0.587958] pci 0000:00:1c.0: bridge window [mem 0xfd700000-0xfd7fffff 64bit pref]
[ 0.588317] pci 0000:00:1c.4: PCI bridge to [bus 05-05]
[ 0.588504] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
[ 0.588694] pci 0000:00:1c.4: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.588885] pci 0000:00:1c.4: bridge window [mem pref disabled]
[ 0.589098] pci 0000:00:1e.0: PCI bridge to [bus 07-07]
[ 0.589288] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
[ 0.589480] pci 0000:00:1e.0: bridge window [mem 0xfeb00000-0xfebfffff]
[ 0.589671] pci 0000:00:1e.0: bridge window [mem 0xfd800000-0xfdffffff 64bit pref]
[ 0.590032] alloc irq_desc for 16 on node -1
[ 0.590034] alloc kstat_irqs on node -1
[ 0.590038] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.590229] pci 0000:00:01.0: setting latency timer to 64
[ 0.590235] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.590426] pci 0000:01:00.0: setting latency timer to 64
[ 0.590431] alloc irq_desc for 17 on node -1
[ 0.590433] alloc kstat_irqs on node -1
[ 0.590435] pci 0000:02:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.590620] pci 0000:02:01.0: setting latency timer to 64
[ 0.590626] alloc irq_desc for 18 on node -1
[ 0.590627] alloc kstat_irqs on node -1
[ 0.590630] pci 0000:02:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.590814] pci 0000:02:02.0: setting latency timer to 64
[ 0.590820] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.591024] pci 0000:00:1c.0: setting latency timer to 64
[ 0.591030] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.591214] pci 0000:00:1c.4: setting latency timer to 64
[ 0.591219] pci 0000:00:1e.0: setting latency timer to 64
[ 0.591222] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.591224] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.591226] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.591228] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.591230] pci_bus 0000:00: resource 8 [mem 0x7cc00000-0xdfffffff]
[ 0.591232] pci_bus 0000:00: resource 9 [mem 0xf0000000-0xffffffff]
[ 0.591234] pci_bus 0000:01: resource 0 [io 0xc000-0xcfff]
[ 0.591235] pci_bus 0000:01: resource 1 [mem 0xfe700000-0xfe9fffff]
[ 0.591237] pci_bus 0000:02: resource 0 [io 0xc000-0xcfff]
[ 0.591239] pci_bus 0000:02: resource 1 [mem 0xfe800000-0xfe9fffff]
[ 0.591241] pci_bus 0000:03: resource 1 [mem 0xfe800000-0xfe8fffff]
[ 0.591242] pci_bus 0000:04: resource 0 [io 0xc000-0xcfff]
[ 0.591244] pci_bus 0000:04: resource 1 [mem 0xfe900000-0xfe9fffff]
[ 0.591246] pci_bus 0000:06: resource 2 [mem 0xfd700000-0xfd7fffff 64bit pref]
[ 0.591248] pci_bus 0000:05: resource 0 [io 0xd000-0xdfff]
[ 0.591249] pci_bus 0000:05: resource 1 [mem 0xfea00000-0xfeafffff]
[ 0.591251] pci_bus 0000:07: resource 0 [io 0xe000-0xefff]
[ 0.591253] pci_bus 0000:07: resource 1 [mem 0xfeb00000-0xfebfffff]
[ 0.591255] pci_bus 0000:07: resource 2 [mem 0xfd800000-0xfdffffff 64bit pref]
[ 0.591257] pci_bus 0000:07: resource 4 [io 0x0000-0x0cf7]
[ 0.591258] pci_bus 0000:07: resource 5 [io 0x0d00-0xffff]
[ 0.591260] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.591262] pci_bus 0000:07: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.591263] pci_bus 0000:07: resource 8 [mem 0x7cc00000-0xdfffffff]
[ 0.591265] pci_bus 0000:07: resource 9 [mem 0xf0000000-0xffffffff]
[ 0.591286] NET: Registered protocol family 2
[ 0.591501] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.591947] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.593876] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.594577] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.594767] TCP reno registered
[ 0.594950] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.595173] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.595488] NET: Registered protocol family 1
[ 0.595898] RPC: Registered udp transport module.
[ 0.596109] RPC: Registered tcp transport module.
[ 0.596293] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.596505] pci 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.596506] pci 0000:00:1a.0: Performing full reset
[ 0.596522] pci 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.596523] pci 0000:00:1a.1: Performing full reset
[ 0.596538] pci 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.596540] pci 0000:00:1a.2: Performing full reset
[ 0.596590] pci 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.596591] pci 0000:00:1d.0: Performing full reset
[ 0.596606] pci 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.596608] pci 0000:00:1d.1: Performing full reset
[ 0.596623] pci 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.596624] pci 0000:00:1d.2: Performing full reset
[ 0.596680] pci 0000:07:00.0: Boot video device
[ 0.596685] PCI: CLS 32 bytes, default 64
[ 0.596739] Trying to unpack rootfs image as initramfs...
[ 0.649203] Freeing initrd memory: 3116k freed
[ 0.650833] kvm: already loaded the other module
[ 0.653212] microcode: CPU0 sig=0x1067a, pf=0x10, revision=0xa07
[ 0.653416] microcode: CPU1 sig=0x1067a, pf=0x10, revision=0xa07
[ 0.653618] microcode: CPU2 sig=0x1067a, pf=0x10, revision=0xa07
[ 0.653810] microcode: CPU3 sig=0x1067a, pf=0x10, revision=0xa07
[ 0.654128] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 0.654477] Scanning for low memory corruption every 60 seconds
[ 0.654991] audit: initializing netlink socket (disabled)
[ 0.655207] type=2000 audit(1268448854.655:1): initialized
[ 0.674896] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.678710] VFS: Disk quotas dquot_6.5.2
[ 0.678974] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.680227] fuse init (API version 7.13)
[ 0.681039] Btrfs loaded
[ 0.681228] msgmni has been set to 3897
[ 0.681516] SELinux: Registering netfilter hooks
[ 0.682184] alg: No test for stdrng (krng)
[ 0.682491] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.682833] io scheduler noop registered
[ 0.683034] io scheduler deadline registered
[ 0.683354] io scheduler cfq registered (default)
[ 0.683666] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.683682] alloc irq_desc for 28 on node -1
[ 0.683683] alloc kstat_irqs on node -1
[ 0.683690] pcieport 0000:00:01.0: irq 28 for MSI/MSI-X
[ 0.683822] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.683845] alloc irq_desc for 29 on node -1
[ 0.683846] alloc kstat_irqs on node -1
[ 0.683852] pcieport 0000:00:1c.0: irq 29 for MSI/MSI-X
[ 0.683995] pcieport 0000:00:1c.4: setting latency timer to 64
[ 0.684032] alloc irq_desc for 30 on node -1
[ 0.684033] alloc kstat_irqs on node -1
[ 0.684039] pcieport 0000:00:1c.4: irq 30 for MSI/MSI-X
[ 0.684159] pcieport 0000:01:00.0: setting latency timer to 64
[ 0.684183] alloc irq_desc for 31 on node -1
[ 0.684185] alloc kstat_irqs on node -1
[ 0.684191] pcieport 0000:01:00.0: irq 31 for MSI/MSI-X
[ 0.684337] pcieport 0000:02:01.0: setting latency timer to 64
[ 0.684361] alloc irq_desc for 32 on node -1
[ 0.684363] alloc kstat_irqs on node -1
[ 0.684369] pcieport 0000:02:01.0: irq 32 for MSI/MSI-X
[ 0.684507] pcieport 0000:02:02.0: setting latency timer to 64
[ 0.684532] alloc irq_desc for 33 on node -1
[ 0.684533] alloc kstat_irqs on node -1
[ 0.684540] pcieport 0000:02:02.0: irq 33 for MSI/MSI-X
[ 0.684834] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.685432] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.685774] ACPI: Power Button [PWRB]
[ 0.686038] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.686377] ACPI: Power Button [PWRF]
[ 0.687152] ACPI: SSDT 000000007cb80260 00235 (v01 DpgPmm P001Ist 00000011 INTL 20060113)
[ 0.688066] ACPI: SSDT 000000007cb80b60 004B2 (v01 PmRef P001Cst 00003001 INTL 20060113)
[ 0.689069] Monitor-Mwait will be used to enter C-1 state
[ 0.689117] Monitor-Mwait will be used to enter C-2 state
[ 0.689174] Monitor-Mwait will be used to enter C-3 state
[ 0.689186] Marking TSC unstable due to TSC halts in idle
[ 0.689446] Switching to clocksource hpet
[ 0.689898] ACPI: SSDT 000000007cb804a0 00235 (v01 DpgPmm P002Ist 00000012 INTL 20060113)
[ 0.690748] ACPI: SSDT 000000007cb81020 00085 (v01 PmRef P002Cst 00003000 INTL 20060113)
[ 0.696339] ACPI: SSDT 000000007cb806e0 00235 (v01 DpgPmm P003Ist 00000012 INTL 20060113)
[ 0.697146] ACPI: SSDT 000000007cb810b0 00085 (v01 PmRef P003Cst 00003000 INTL 20060113)
[ 0.698750] ACPI: SSDT 000000007cb80920 00235 (v01 DpgPmm P004Ist 00000012 INTL 20060113)
[ 0.699569] ACPI: SSDT 000000007cb81140 00085 (v01 PmRef P004Cst 00003000 INTL 20060113)
[ 0.703232] XENFS: not registering filesystem on non-xen platform
[ 0.708034] Non-volatile memory driver v1.3
[ 0.708330] Linux agpgart interface v0.103
[ 0.708591] agpgart-intel 0000:00:00.0: Intel Q45/Q43 Chipset
[ 0.709702] agpgart-intel 0000:00:00.0: detected 32764K stolen memory
[ 0.821524] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[ 0.821878] [drm] Initialized drm 1.1.0 20060810
[ 0.822157] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.066117] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.066946] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.070120] brd: module loaded
[ 1.071635] loop: module loaded
[ 1.072277] ahci 0000:04:00.0: version 3.0
[ 1.072291] ahci 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.072517] alloc irq_desc for 34 on node -1
[ 1.072519] alloc kstat_irqs on node -1
[ 1.072527] ahci 0000:04:00.0: irq 34 for MSI/MSI-X
[ 1.072568] ahci 0000:04:00.0: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 1.072907] ahci 0000:04:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 1.073293] ahci 0000:04:00.0: setting latency timer to 64
[ 1.073299] ahci 0000:04:00.0: The port is not capable of FBS
[ 1.073526] ahci 0000:04:00.0: The port is not capable of FBS
[ 1.073822] scsi0 : ahci
[ 1.074229] scsi1 : ahci
[ 1.074564] ata1: SATA max UDMA/133 abar m2048@0xfe9ff800 port 0xfe9ff900 irq 34
[ 1.074905] ata2: SATA max UDMA/133 abar m2048@0xfe9ff800 port 0xfe9ff980 irq 34
[ 1.075386] ata_piix 0000:00:1f.2: version 2.13
[ 1.075394] alloc irq_desc for 22 on node -1
[ 1.075395] alloc kstat_irqs on node -1
[ 1.075399] ata_piix 0000:00:1f.2: PCI INT B -> GSI 22 (level, low) -> IRQ 22
[ 1.075591] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 1.075952] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 1.076033] scsi2 : ata_piix
[ 1.076479] scsi3 : ata_piix
[ 1.078064] ata3: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xff90 irq 14
[ 1.078280] ata4: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xff98 irq 15
[ 1.078499] ata_piix 0000:00:1f.5: PCI INT B -> GSI 22 (level, low) -> IRQ 22
[ 1.078729] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[ 1.079102] ata_piix 0000:00:1f.5: setting latency timer to 64
[ 1.079170] scsi4 : ata_piix
[ 1.079556] scsi5 : ata_piix
[ 1.080943] ata5: SATA max UDMA/133 cmd 0xa880 ctl 0xa800 bmdma 0xa080 irq 22
[ 1.081161] ata6: SATA max UDMA/133 cmd 0xa480 ctl 0xa400 bmdma 0xa088 irq 22
[ 1.081855] Intel(R) PRO/1000 Network Driver - version 7.3.21-k5-NAPI
[ 1.082058] Copyright (c) 1999-2006 Intel Corporation.
[ 1.082344] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
[ 1.082536] e1000e: Copyright (c) 1999 - 2009 Intel Corporation.
[ 1.082744] alloc irq_desc for 20 on node -1
[ 1.082745] alloc kstat_irqs on node -1
[ 1.082749] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.082944] e1000e 0000:00:19.0: setting latency timer to 64
[ 1.083008] alloc irq_desc for 35 on node -1
[ 1.083009] alloc kstat_irqs on node -1
[ 1.083021] e1000e 0000:00:19.0: irq 35 for MSI/MSI-X
[ 1.212796] 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:23:54:9a:46:ea
[ 1.213152] 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[ 1.213393] 0000:00:19.0: eth0: MAC: 8, PHY: 8, PBA No: ffffff-0ff
[ 1.213741] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 1.213930] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.214371] sky2: driver version 1.27
[ 1.214797] tun: Universal TUN/TAP device driver, 1.6
[ 1.214982] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.215431] console [netcon0] enabled
[ 1.215617] netconsole: network logging started
[ 1.216079] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.216291] ehci_hcd: block sizes: qh 104 qtd 96 itd 192 sitd 96
[ 1.216306] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.216510] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 1.216513] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 1.216717] drivers/usb/core/inode.c: creating file 'devices'
[ 1.216721] drivers/usb/core/inode.c: creating file '001'
[ 1.216828] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 1.217191] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
[ 1.217195] ehci_hcd 0000:00:1a.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
[ 1.217212] ehci_hcd 0000:00:1a.7: debug port 1
[ 1.217409] ehci_hcd 0000:00:1a.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 1.221301] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 1.221303] ehci_hcd 0000:00:1a.7: supports USB remote wakeup
[ 1.221314] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfe6f9000
[ 1.221506] ehci_hcd 0000:00:1a.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 1.225388] ehci_hcd 0000:00:1a.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
[ 1.231015] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 1.231229] usb usb1: default language 0x0409
[ 1.231234] usb usb1: udev 1, busnum 1, minor = 0
[ 1.231236] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.231437] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.231770] usb usb1: Product: EHCI Host Controller
[ 1.231954] usb usb1: Manufacturer: Linux 2.6.34-rc1 ehci_hcd
[ 1.232154] usb usb1: SerialNumber: 0000:00:1a.7
[ 1.232464] usb usb1: usb_probe_device
[ 1.232466] usb usb1: configuration #1 chosen from 1 choice
[ 1.232471] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 1.232573] hub 1-0:1.0: usb_probe_interface
[ 1.232574] hub 1-0:1.0: usb_probe_interface - got id
[ 1.232576] hub 1-0:1.0: USB hub found
[ 1.232762] hub 1-0:1.0: 6 ports detected
[ 1.232944] hub 1-0:1.0: standalone hub
[ 1.232945] hub 1-0:1.0: no power switching (usb 1.0)
[ 1.232946] hub 1-0:1.0: individual port over-current protection
[ 1.232948] hub 1-0:1.0: power on to power good time: 20ms
[ 1.232951] hub 1-0:1.0: local power source is good
[ 1.232953] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 1.232976] drivers/usb/core/inode.c: creating file '001'
[ 1.233014] alloc irq_desc for 23 on node -1
[ 1.233016] alloc kstat_irqs on node -1
[ 1.233020] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.233232] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.233235] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.233441] drivers/usb/core/inode.c: creating file '002'
[ 1.233547] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 1.233875] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
[ 1.233878] ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
[ 1.233895] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.234075] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 1.237961] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 1.237963] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
[ 1.237972] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfe6f8000
[ 1.238178] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 1.242048] ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
[ 1.247015] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.247234] usb usb2: default language 0x0409
[ 1.247239] usb usb2: udev 1, busnum 2, minor = 128
[ 1.247240] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.247441] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.247774] usb usb2: Product: EHCI Host Controller
[ 1.247954] usb usb2: Manufacturer: Linux 2.6.34-rc1 ehci_hcd
[ 1.248148] usb usb2: SerialNumber: 0000:00:1d.7
[ 1.248450] usb usb2: usb_probe_device
[ 1.248451] usb usb2: configuration #1 chosen from 1 choice
[ 1.248456] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 1.248556] hub 2-0:1.0: usb_probe_interface
[ 1.248558] hub 2-0:1.0: usb_probe_interface - got id
[ 1.248559] hub 2-0:1.0: USB hub found
[ 1.248738] hub 2-0:1.0: 6 ports detected
[ 1.248915] hub 2-0:1.0: standalone hub
[ 1.248916] hub 2-0:1.0: no power switching (usb 1.0)
[ 1.248917] hub 2-0:1.0: individual port over-current protection
[ 1.248919] hub 2-0:1.0: power on to power good time: 20ms
[ 1.248922] hub 2-0:1.0: local power source is good
[ 1.248923] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 1.248944] drivers/usb/core/inode.c: creating file '001'
[ 1.249165] 116x: driver isp116x-hcd, 03 Nov 2005
[ 1.249443] driver isp1362-hcd, 2005-04-04
[ 1.249719] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.249907] ohci_hcd: block sizes: ed 80 td 96
[ 1.250006] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.250228] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.250431] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 1.250434] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.250628] drivers/usb/core/inode.c: creating file '003'
[ 1.250735] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 1.251077] uhci_hcd 0000:00:1a.0: detected 2 ports
[ 1.251283] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000
[ 1.251284] uhci_hcd 0000:00:1a.0: Performing full reset
[ 1.251296] uhci_hcd 0000:00:1a.0: supports USB remote wakeup
[ 1.251306] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000b400
[ 1.251520] usb usb3: default language 0x0409
[ 1.251525] usb usb3: udev 1, busnum 3, minor = 256
[ 1.251526] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.251716] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.252055] usb usb3: Product: UHCI Host Controller
[ 1.252265] usb usb3: Manufacturer: Linux 2.6.34-rc1 uhci_hcd
[ 1.252462] usb usb3: SerialNumber: 0000:00:1a.0
[ 1.252763] usb usb3: usb_probe_device
[ 1.252765] usb usb3: configuration #1 chosen from 1 choice
[ 1.252770] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[ 1.252870] hub 3-0:1.0: usb_probe_interface
[ 1.252872] hub 3-0:1.0: usb_probe_interface - got id
[ 1.252873] hub 3-0:1.0: USB hub found
[ 1.253056] hub 3-0:1.0: 2 ports detected
[ 1.253262] hub 3-0:1.0: standalone hub
[ 1.253263] hub 3-0:1.0: no power switching (usb 1.0)
[ 1.253264] hub 3-0:1.0: individual port over-current protection
[ 1.253266] hub 3-0:1.0: power on to power good time: 2ms
[ 1.253269] hub 3-0:1.0: local power source is good
[ 1.253270] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 1.253282] drivers/usb/core/inode.c: creating file '001'
[ 1.253308] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.0
[ 1.253325] alloc irq_desc for 21 on node -1
[ 1.253327] alloc kstat_irqs on node -1
[ 1.253330] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 1.253528] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 1.253531] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.253718] drivers/usb/core/inode.c: creating file '004'
[ 1.253826] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 1.254174] uhci_hcd 0000:00:1a.1: detected 2 ports
[ 1.254367] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000
[ 1.254369] uhci_hcd 0000:00:1a.1: Performing full reset
[ 1.254382] uhci_hcd 0000:00:1a.1: supports USB remote wakeup
[ 1.254392] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000b480
[ 1.254603] usb usb4: default language 0x0409
[ 1.254608] usb usb4: udev 1, busnum 4, minor = 384
[ 1.254610] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.254804] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.255154] usb usb4: Product: UHCI Host Controller
[ 1.255347] usb usb4: Manufacturer: Linux 2.6.34-rc1 uhci_hcd
[ 1.255538] usb usb4: SerialNumber: 0000:00:1a.1
[ 1.255839] usb usb4: usb_probe_device
[ 1.255841] usb usb4: configuration #1 chosen from 1 choice
[ 1.255845] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[ 1.255946] hub 4-0:1.0: usb_probe_interface
[ 1.255947] hub 4-0:1.0: usb_probe_interface - got id
[ 1.255949] hub 4-0:1.0: USB hub found
[ 1.256141] hub 4-0:1.0: 2 ports detected
[ 1.256342] hub 4-0:1.0: standalone hub
[ 1.256343] hub 4-0:1.0: no power switching (usb 1.0)
[ 1.256344] hub 4-0:1.0: individual port over-current protection
[ 1.256346] hub 4-0:1.0: power on to power good time: 2ms
[ 1.256349] hub 4-0:1.0: local power source is good
[ 1.256350] hub 4-0:1.0: trying to enable port power on non-switchable hub
[ 1.256360] drivers/usb/core/inode.c: creating file '001'
[ 1.256384] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.1
[ 1.256401] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.256596] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 1.256598] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 1.256786] drivers/usb/core/inode.c: creating file '005'
[ 1.256892] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[ 1.257246] uhci_hcd 0000:00:1a.2: detected 2 ports
[ 1.257446] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000
[ 1.257448] uhci_hcd 0000:00:1a.2: Performing full reset
[ 1.257459] uhci_hcd 0000:00:1a.2: supports USB remote wakeup
[ 1.257463] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000b800
[ 1.257671] usb usb5: default language 0x0409
[ 1.257676] usb usb5: udev 1, busnum 5, minor = 512
[ 1.257678] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.257866] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.258215] usb usb5: Product: UHCI Host Controller
[ 1.258408] usb usb5: Manufacturer: Linux 2.6.34-rc1 uhci_hcd
[ 1.258595] usb usb5: SerialNumber: 0000:00:1a.2
[ 1.258899] usb usb5: usb_probe_device
[ 1.258901] usb usb5: configuration #1 chosen from 1 choice
[ 1.258905] usb usb5: adding 5-0:1.0 (config #1, interface 0)
[ 1.259004] hub 5-0:1.0: usb_probe_interface
[ 1.259006] hub 5-0:1.0: usb_probe_interface - got id
[ 1.259007] hub 5-0:1.0: USB hub found
[ 1.259207] hub 5-0:1.0: 2 ports detected
[ 1.259399] hub 5-0:1.0: standalone hub
[ 1.259400] hub 5-0:1.0: no power switching (usb 1.0)
[ 1.259402] hub 5-0:1.0: individual port over-current protection
[ 1.259403] hub 5-0:1.0: power on to power good time: 2ms
[ 1.259406] hub 5-0:1.0: local power source is good
[ 1.259408] hub 5-0:1.0: trying to enable port power on non-switchable hub
[ 1.259418] drivers/usb/core/inode.c: creating file '001'
[ 1.259438] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.2
[ 1.259456] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.259648] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.259650] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.259836] drivers/usb/core/inode.c: creating file '006'
[ 1.259944] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[ 1.260305] uhci_hcd 0000:00:1d.0: detected 2 ports
[ 1.260500] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
[ 1.260502] uhci_hcd 0000:00:1d.0: Performing full reset
[ 1.260513] uhci_hcd 0000:00:1d.0: supports USB remote wakeup
[ 1.260517] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ac00
[ 1.260725] usb usb6: default language 0x0409
[ 1.260730] usb usb6: udev 1, busnum 6, minor = 640
[ 1.260731] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.260920] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.261278] usb usb6: Product: UHCI Host Controller
[ 1.261469] usb usb6: Manufacturer: Linux 2.6.34-rc1 uhci_hcd
[ 1.261655] usb usb6: SerialNumber: 0000:00:1d.0
[ 1.261954] usb usb6: usb_probe_device
[ 1.261956] usb usb6: configuration #1 chosen from 1 choice
[ 1.261960] usb usb6: adding 6-0:1.0 (config #1, interface 0)
[ 1.262068] hub 6-0:1.0: usb_probe_interface
[ 1.262070] hub 6-0:1.0: usb_probe_interface - got id
[ 1.262071] hub 6-0:1.0: USB hub found
[ 1.262270] hub 6-0:1.0: 2 ports detected
[ 1.262452] hub 6-0:1.0: standalone hub
[ 1.262453] hub 6-0:1.0: no power switching (usb 1.0)
[ 1.262454] hub 6-0:1.0: individual port over-current protection
[ 1.262455] hub 6-0:1.0: power on to power good time: 2ms
[ 1.262458] hub 6-0:1.0: local power source is good
[ 1.262460] hub 6-0:1.0: trying to enable port power on non-switchable hub
[ 1.262470] drivers/usb/core/inode.c: creating file '001'
[ 1.262494] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0
[ 1.262507] alloc irq_desc for 19 on node -1
[ 1.262509] alloc kstat_irqs on node -1
[ 1.262512] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.262699] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.262701] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.262884] drivers/usb/core/inode.c: creating file '007'
[ 1.262992] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[ 1.263340] uhci_hcd 0000:00:1d.1: detected 2 ports
[ 1.263525] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
[ 1.263527] uhci_hcd 0000:00:1d.1: Performing full reset
[ 1.263538] uhci_hcd 0000:00:1d.1: supports USB remote wakeup
[ 1.263548] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b000
[ 1.263754] usb usb7: default language 0x0409
[ 1.263759] usb usb7: udev 1, busnum 7, minor = 768
[ 1.263761] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.263950] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.264307] usb usb7: Product: UHCI Host Controller
[ 1.264496] usb usb7: Manufacturer: Linux 2.6.34-rc1 uhci_hcd
[ 1.264683] usb usb7: SerialNumber: 0000:00:1d.1
[ 1.264983] usb usb7: usb_probe_device
[ 1.264984] usb usb7: configuration #1 chosen from 1 choice
[ 1.264989] usb usb7: adding 7-0:1.0 (config #1, interface 0)
[ 1.265092] hub 7-0:1.0: usb_probe_interface
[ 1.265093] hub 7-0:1.0: usb_probe_interface - got id
[ 1.265095] hub 7-0:1.0: USB hub found
[ 1.265302] hub 7-0:1.0: 2 ports detected
[ 1.265492] hub 7-0:1.0: standalone hub
[ 1.265493] hub 7-0:1.0: no power switching (usb 1.0)
[ 1.265494] hub 7-0:1.0: individual port over-current protection
[ 1.265495] hub 7-0:1.0: power on to power good time: 2ms
[ 1.265498] hub 7-0:1.0: local power source is good
[ 1.265500] hub 7-0:1.0: trying to enable port power on non-switchable hub
[ 1.265512] drivers/usb/core/inode.c: creating file '001'
[ 1.265535] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1
[ 1.265549] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.265745] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.265747] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.265938] drivers/usb/core/inode.c: creating file '008'
[ 1.266053] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[ 1.266415] uhci_hcd 0000:00:1d.2: detected 2 ports
[ 1.266602] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
[ 1.266603] uhci_hcd 0000:00:1d.2: Performing full reset
[ 1.266615] uhci_hcd 0000:00:1d.2: supports USB remote wakeup
[ 1.266619] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b080
[ 1.266829] usb usb8: default language 0x0409
[ 1.266834] usb usb8: udev 1, busnum 8, minor = 896
[ 1.266835] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.267028] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.267391] usb usb8: Product: UHCI Host Controller
[ 1.267575] usb usb8: Manufacturer: Linux 2.6.34-rc1 uhci_hcd
[ 1.267763] usb usb8: SerialNumber: 0000:00:1d.2
[ 1.268071] usb usb8: usb_probe_device
[ 1.268073] usb usb8: configuration #1 chosen from 1 choice
[ 1.268078] usb usb8: adding 8-0:1.0 (config #1, interface 0)
[ 1.268184] hub 8-0:1.0: usb_probe_interface
[ 1.268186] hub 8-0:1.0: usb_probe_interface - got id
[ 1.268187] hub 8-0:1.0: USB hub found
[ 1.268376] hub 8-0:1.0: 2 ports detected
[ 1.272456] hub 8-0:1.0: standalone hub
[ 1.272457] hub 8-0:1.0: no power switching (usb 1.0)
[ 1.272459] hub 8-0:1.0: individual port over-current protection
[ 1.272460] hub 8-0:1.0: power on to power good time: 2ms
[ 1.272463] hub 8-0:1.0: local power source is good
[ 1.272465] hub 8-0:1.0: trying to enable port power on non-switchable hub
[ 1.272475] drivers/usb/core/inode.c: creating file '001'
[ 1.272500] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2
[ 1.272620] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.272818] xhci_hcd 0000:03:00.0: setting latency timer to 64
[ 1.272821] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 1.273008] drivers/usb/core/inode.c: creating file '009'
[ 1.273121] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 9
[ 1.273588] xhci_hcd 0000:03:00.0: supports USB remote wakeup
[ 1.273598] xhci_hcd 0000:03:00.0: irq 17, io mem 0xfe8fe000
[ 1.273814] usb usb9: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
[ 1.274164] usb usb9: default language 0x0409
[ 1.274168] usb usb9: udev 1, busnum 9, minor = 1024
[ 1.274170] usb usb9: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.274367] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.274705] usb usb9: Product: xHCI Host Controller
[ 1.274892] usb usb9: Manufacturer: Linux 2.6.34-rc1 xhci_hcd
[ 1.275082] usb usb9: SerialNumber: 0000:03:00.0
[ 1.275394] usb usb9: usb_probe_device
[ 1.275396] usb usb9: configuration #1 chosen from 1 choice
[ 1.275398] xHCI xhci_add_endpoint called for root hub
[ 1.275400] xHCI xhci_check_bandwidth called for root hub
[ 1.275404] usb usb9: adding 9-0:1.0 (config #1, interface 0)
[ 1.275506] hub 9-0:1.0: usb_probe_interface
[ 1.275508] hub 9-0:1.0: usb_probe_interface - got id
[ 1.275509] hub 9-0:1.0: USB hub found
[ 1.275694] hub 9-0:1.0: 4 ports detected
[ 1.275875] hub 9-0:1.0: standalone hub
[ 1.275876] hub 9-0:1.0: individual port power switching
[ 1.275878] hub 9-0:1.0: individual port over-current protection
[ 1.275879] hub 9-0:1.0: TT requires at most 8 FS bit times (666 ns)
[ 1.275881] hub 9-0:1.0: power on to power good time: 20ms
[ 1.275884] hub 9-0:1.0: local power source is good
[ 1.275885] hub 9-0:1.0: enabling power on all ports
[ 1.275910] drivers/usb/core/inode.c: creating file '001'
[ 1.276032] sl811: driver sl811-hcd, 19 May 2005
[ 1.276423] r8a66597_hcd: driver r8a66597_hcd, 2009-05-26
[ 1.277195] usbcore: registered new interface driver usblp
[ 1.277384] Initializing USB Mass Storage driver...
[ 1.277680] usbcore: registered new interface driver usb-storage
[ 1.277862] USB Mass Storage support registered.
[ 1.278165] usbcore: registered new interface driver libusual
[ 1.278532] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 1.281396] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.281594] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.281999] mice: PS/2 mouse device common for all mice
[ 1.282622] rtc_cmos 00:03: RTC can wake from S4
[ 1.282909] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.283126] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.283447] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.283785] ACPI: I/O resource 0000:00:1f.3 [0x400-0x41f] conflicts with ACPI region SMRG [0x400-0x40f]
[ 1.284133] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 1.284934] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[ 1.286720] cpuidle: using governor ladder
[ 1.289284] cpuidle: using governor menu
[ 1.291559] usbcore: registered new interface driver hiddev
[ 1.291808] usbcore: registered new interface driver usbhid
[ 1.291991] usbhid: USB HID core driver
[ 1.294612] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 1.294979] alloc irq_desc for 36 on node -1
[ 1.294981] alloc kstat_irqs on node -1
[ 1.294990] HDA Intel 0000:00:1b.0: irq 36 for MSI/MSI-X
[ 1.295017] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 1.306016] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 1.310131] ALSA device list:
[ 1.310333] #0: HDA Intel at 0xfe6f0000 irq 36
[ 1.310576] Netfilter messages via NETLINK v0.30.
[ 1.310786] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 1.311151] ctnetlink v0.93: registering with nfnetlink.
[ 1.311721] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.311931] TCP cubic registered
[ 1.312124] Initializing XFRM netlink socket
[ 1.312761] NET: Registered protocol family 10
[ 1.313551] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 1.313779] IPv6 over IPv4 tunneling driver
[ 1.314431] NET: Registered protocol family 17
[ 1.316507] PM: Resume from disk failed.
[ 1.316518] registered taskstats version 1
[ 1.317014] Magic number: 2:58:915
[ 1.333302] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0000
[ 1.349347] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
[ 1.352441] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.355127] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.359103] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.362098] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.365105] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.372295] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.375094] hub 9-0:1.0: port 3: status 0101 change 0001
[ 1.381100] ata2: SATA link down (SStatus 0 SControl 370)
[ 1.381108] ata1: SATA link down (SStatus 0 SControl 370)
[ 1.397715] ata5: SATA link down (SStatus 0 SControl 300)
[ 1.408334] ata6: SATA link down (SStatus 0 SControl 300)
[ 1.470309] logips2pp: Detected unknown logitech mouse model 57
[ 1.475094] hub 9-0:1.0: state 7 ports 4 chg 0008 evt 0000
[ 1.475101] hub 9-0:1.0: port 3, status 0101, change 0000, 12 Mb/s
[ 1.577153] usb 9-3: new full speed USB device using xhci_hcd and address 0
[ 1.594041] usb 9-3: ep0 maxpacket = 8
[ 1.594170] usb 9-3: Successful evaluate context command
[ 1.698747] ata4.00: SATA link down (SStatus 0 SControl 300)
[ 1.698944] ata4.01: SATA link down (SStatus 0 SControl 300)
[ 1.738043] usb 9-3: skipped 4 descriptors after interface
[ 1.738045] usb 9-3: skipped 2 descriptors after interface
[ 1.738048] usb 9-3: skipped 1 descriptor after endpoint
[ 1.738050] usb 9-3: skipped 2 descriptors after interface
[ 1.738053] usb 9-3: skipped 1 descriptor after endpoint
[ 1.738055] usb 9-3: skipped 2 descriptors after interface
[ 1.738057] usb 9-3: skipped 1 descriptor after endpoint
[ 1.738059] usb 9-3: skipped 2 descriptors after interface
[ 1.738061] usb 9-3: skipped 1 descriptor after endpoint
[ 1.741021] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 1.742039] usb 9-3: default language 0x0409
[ 1.765016] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 1.766036] usb 9-3: udev 2, busnum 9, minor = 1025
[ 1.766038] usb 9-3: New USB device found, idVendor=0471, idProduct=0311
[ 1.766244] usb 9-3: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[ 1.766448] usb 9-3: SerialNumber: 01680000EA164101
[ 1.766811] usb 9-3: usb_probe_device
[ 1.766813] usb 9-3: configuration #1 chosen from 1 choice
[ 1.767184] usb 9-3: Successful Endpoint Configure command
[ 1.769035] usb 9-3: adding 9-3:1.0 (config #1, interface 0)
[ 1.769151] usb 9-3: adding 9-3:1.1 (config #1, interface 1)
[ 1.769235] usb 9-3: adding 9-3:1.2 (config #1, interface 2)
[ 1.769319] drivers/usb/core/inode.c: creating file '002'
[ 1.839142] ata3.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.839356] ata3.01: SATA link down (SStatus 0 SControl 300)
[ 1.842219] ata3.00: ATA-7: WDC WD800JD-60MSA1, 10.01E01, max UDMA/100
[ 1.842409] ata3.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.845224] ata3.00: configured for UDMA/100
[ 1.845509] scsi 2:0:0:0: Direct-Access ATA WDC WD800JD-60MS 10.0 PQ: 0 ANSI: 5
[ 1.846269] sd 2:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 1.846424] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 1.846925] sd 2:0:0:0: [sda] Write Protect is off
[ 1.847126] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.847148] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.847605] sda: sda1 sda2 < sda5 >
[ 1.887209] sd 2:0:0:0: [sda] Attached SCSI disk
[ 1.887440] Freeing unused kernel memory: 564k freed
[ 1.887767] Write protecting the kernel read-only data: 12288k
[ 1.888237] Freeing unused kernel memory: 1772k freed
[ 1.889027] Freeing unused kernel memory: 1156k freed
[ 1.937197] input: ImExPS/2 Logitech Explorer Mouse as /devices/platform/i8042/serio1/input/input3
[ 2.265647] PM: Starting manual resume from disk
[ 2.265834] PM: Resume from partition 8:5
[ 2.265835] PM: Checking hibernation image.
[ 2.266002] PM: Error -22 checking image file
[ 2.266003] PM: Resume from disk failed.
[ 2.270875] PM: Marking nosave pages: 000000000009f000 - 0000000000100000
[ 2.270879] PM: Basic memory bitmaps created
[ 2.285230] PM: Basic memory bitmaps freed
[ 2.327630] kjournald starting. Commit interval 5 seconds
[ 2.327667] EXT3-fs (sda1): mounted filesystem with writeback data mode
[ 2.454032] usb usb3: suspend_rh (auto-stop)
[ 2.454052] usb usb4: suspend_rh (auto-stop)
[ 2.454070] usb usb5: suspend_rh (auto-stop)
[ 2.454087] usb usb6: suspend_rh (auto-stop)
[ 2.454105] usb usb7: suspend_rh (auto-stop)
[ 2.454123] usb usb8: suspend_rh (auto-stop)
[ 3.613978] udevd version 125 started
[ 4.421461] Linux video capture interface: v2.00
[ 4.481833] pwc: Philips webcam module version 10.0.13 loaded.
[ 4.482042] pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
[ 4.482436] pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
[ 4.482791] pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
[ 4.483152] pwc: Trace options: 0x0001
[ 4.483171] Philips webcam 9-3:1.0: usb_probe_interface
[ 4.483173] Philips webcam 9-3:1.0: usb_probe_interface - got id
[ 4.483174] pwc: Philips PCVC740K (ToUCam Pro)/PCVC840 (ToUCam II) USB webcam detected.
[ 4.515833] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 4.516894] pwc: Registered as video0.
[ 4.518834] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint
[ 4.520834] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint
[ 4.521051] Philips webcam 9-3:1.1: usb_probe_interface
[ 4.521053] Philips webcam 9-3:1.1: usb_probe_interface - got id
[ 4.521058] Philips webcam 9-3:1.2: usb_probe_interface
[ 4.521060] Philips webcam 9-3:1.2: usb_probe_interface - got id
[ 4.521073] usbcore: registered new interface driver Philips webcam
[ 5.508089] Adding 3229028k swap on /dev/sda5. Priority:-1 extents:1 across:3229028k
[ 5.777093] EXT3-fs (sda1): using internal journal
[ 8.389199] e1000e 0000:00:19.0: irq 35 for MSI/MSI-X
[ 8.440062] e1000e 0000:00:19.0: irq 35 for MSI/MSI-X
[ 8.440405] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 9.978906] e1000e: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 9.979266] 0000:00:19.0: eth1: 10/100 speed: disabling TSO
[ 9.979772] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 12.957593] usb 9-3: Successful Endpoint Configure command
[ 12.967542] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7ac74000, num_trbs = 10
[ 12.967553] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af8c000, num_trbs = 10
[ 12.985500] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
[ 20.946116] eth1: no IPv6 routers present
[ 40.029279] usb 9-3: Successful Endpoint Configure command
[ 40.039186] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a814000, num_trbs = 10
[ 40.039198] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b734000, num_trbs = 10
[ 40.057195] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
[ 40.216270] usb 9-3: Successful Endpoint Configure command
[ 40.226183] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a9c0000, num_trbs = 10
[ 40.226193] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a98c000, num_trbs = 10
[ 40.245183] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
[ 40.399261] usb 9-3: Successful Endpoint Configure command
[ 40.408210] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a9c0000, num_trbs = 10
[ 40.408220] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a98c000, num_trbs = 10
[ 47.145805] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
[ 48.076894] usb 9-3: Successful Endpoint Configure command
[ 48.086805] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b180000, num_trbs = 10
[ 48.086816] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b47c000, num_trbs = 10
[ 48.105803] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
[ 48.263885] usb 9-3: Successful Endpoint Configure command
[ 48.273796] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7bba0000, num_trbs = 10
[ 48.273807] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af6c000, num_trbs = 10
[ 48.292793] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
[ 48.446875] usb 9-3: Successful Endpoint Configure command
[ 48.456784] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7bba0000, num_trbs = 10
[ 48.456794] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af6c000, num_trbs = 10
[ 51.778648] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
[-- Attachment #3: lsusb-with-patch.txt --]
[-- Type: text/plain, Size: 42403 bytes --]
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.34-rc1 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:1d.7
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 6
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.34-rc1 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.34-rc1 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.34-rc1 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.34-rc1 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1a.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.34-rc1 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:1a.7
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 6
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.34-rc1 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1a.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.34-rc1 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1a.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 009 Device 002: ID 0471:0311 Philips PCVC740K ToUcam Pro [pwc]
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0471 Philips
idProduct 0x0311 PCVC740K ToUcam Pro [pwc]
bcdDevice 0.03
iManufacturer 0
iProduct 0
iSerial 1 01680000EA164101
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 490
bNumInterfaces 3
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0000 1x 0 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x00c4 1x 196 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 2
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0124 1x 292 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 3
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x01c0 1x 448 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 4
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0250 1x 592 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 5
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x02c0 1x 704 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 6
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0308 1x 776 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 7
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0348 1x 840 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 8
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0380 1x 896 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 9
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x03c0 1x 960 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 10
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x03c0 1x 960 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 1 Audio
bInterfaceSubClass 1 Control Device
bInterfaceProtocol 0
iInterface 0
AudioControl Interface Descriptor:
bLength 9
bDescriptorType 36
bDescriptorSubtype 1 (HEADER)
bcdADC 1.00
wTotalLength 38
bInCollection 1
baInterfaceNr( 0) 2
AudioControl Interface Descriptor:
bLength 12
bDescriptorType 36
bDescriptorSubtype 2 (INPUT_TERMINAL)
bTerminalID 1
wTerminalType 0x0201 Microphone
bAssocTerminal 0
bNrChannels 1
wChannelConfig 0x0000
iChannelNames 0
iTerminal 0
AudioControl Interface Descriptor:
bLength 8
bDescriptorType 36
bDescriptorSubtype 6 (FEATURE_UNIT)
bUnitID 2
bSourceID 1
bControlSize 1
bmaControls( 0) 0x03
Mute
Volume
iFeature 0
AudioControl Interface Descriptor:
bLength 9
bDescriptorType 36
bDescriptorSubtype 3 (OUTPUT_TERMINAL)
bTerminalID 3
wTerminalType 0x0101 USB Streaming
bAssocTerminal 0
bSourceID 2
iTerminal 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 1 Audio
bInterfaceSubClass 2 Streaming
bInterfaceProtocol 0
iInterface 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 1
bNumEndpoints 1
bInterfaceClass 1 Audio
bInterfaceSubClass 2 Streaming
bInterfaceProtocol 0
iInterface 0
AudioStreaming Interface Descriptor:
bLength 7
bDescriptorType 36
bDescriptorSubtype 1 (AS_GENERAL)
bTerminalLink 3
bDelay 1 frames
wFormatTag 1 PCM
AudioStreaming Interface Descriptor:
bLength 11
bDescriptorType 36
bDescriptorSubtype 2 (FORMAT_TYPE)
bFormatType 1 (FORMAT_TYPE_I)
bNrChannels 1
bSubframeSize 2
bBitResolution 16
bSamFreqType 1 Discrete
tSamFreq[ 0] 44100
Endpoint Descriptor:
bLength 9
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x005a 1x 90 bytes
bInterval 1
bRefresh 0
bSynchAddress 0
AudioControl Endpoint Descriptor:
bLength 7
bDescriptorType 37
bDescriptorSubtype 1 (EP_GENERAL)
bmAttributes 0x00
bLockDelayUnits 0 Undefined
wLockDelay 0 Undefined
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 2
bNumEndpoints 1
bInterfaceClass 1 Audio
bInterfaceSubClass 2 Streaming
bInterfaceProtocol 0
iInterface 0
AudioStreaming Interface Descriptor:
bLength 7
bDescriptorType 36
bDescriptorSubtype 1 (AS_GENERAL)
bTerminalLink 3
bDelay 1 frames
wFormatTag 1 PCM
AudioStreaming Interface Descriptor:
bLength 11
bDescriptorType 36
bDescriptorSubtype 2 (FORMAT_TYPE)
bFormatType 1 (FORMAT_TYPE_I)
bNrChannels 1
bSubframeSize 2
bBitResolution 16
bSamFreqType 1 Discrete
tSamFreq[ 0] 22050
Endpoint Descriptor:
bLength 9
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x002e 1x 46 bytes
bInterval 1
bRefresh 0
bSynchAddress 0
AudioControl Endpoint Descriptor:
bLength 7
bDescriptorType 37
bDescriptorSubtype 1 (EP_GENERAL)
bmAttributes 0x00
bLockDelayUnits 0 Undefined
wLockDelay 0 Undefined
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 3
bNumEndpoints 1
bInterfaceClass 1 Audio
bInterfaceSubClass 2 Streaming
bInterfaceProtocol 0
iInterface 0
AudioStreaming Interface Descriptor:
bLength 7
bDescriptorType 36
bDescriptorSubtype 1 (AS_GENERAL)
bTerminalLink 3
bDelay 1 frames
wFormatTag 1 PCM
AudioStreaming Interface Descriptor:
bLength 11
bDescriptorType 36
bDescriptorSubtype 2 (FORMAT_TYPE)
bFormatType 1 (FORMAT_TYPE_I)
bNrChannels 1
bSubframeSize 2
bBitResolution 16
bSamFreqType 1 Discrete
tSamFreq[ 0] 11025
Endpoint Descriptor:
bLength 9
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0019 1x 25 bytes
bInterval 1
bRefresh 0
bSynchAddress 0
AudioControl Endpoint Descriptor:
bLength 7
bDescriptorType 37
bDescriptorSubtype 1 (EP_GENERAL)
bmAttributes 0x00
bLockDelayUnits 0 Undefined
wLockDelay 0 Undefined
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 4
bNumEndpoints 1
bInterfaceClass 1 Audio
bInterfaceSubClass 2 Streaming
bInterfaceProtocol 0
iInterface 0
AudioStreaming Interface Descriptor:
bLength 7
bDescriptorType 36
bDescriptorSubtype 1 (AS_GENERAL)
bTerminalLink 3
bDelay 1 frames
wFormatTag 1 PCM
AudioStreaming Interface Descriptor:
bLength 11
bDescriptorType 36
bDescriptorSubtype 2 (FORMAT_TYPE)
bFormatType 1 (FORMAT_TYPE_I)
bNrChannels 1
bSubframeSize 2
bBitResolution 16
bSamFreqType 1 Discrete
tSamFreq[ 0] 8000
Endpoint Descriptor:
bLength 9
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 1
bRefresh 0
bSynchAddress 0
AudioControl Endpoint Descriptor:
bLength 7
bDescriptorType 37
bDescriptorSubtype 1 (EP_GENERAL)
bmAttributes 0x00
bLockDelayUnits 0 Undefined
wLockDelay 0 Undefined
Device Status: 0x0002
(Bus Powered)
Remote Wakeup Enabled
Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 3
bMaxPacketSize0 9
idVendor 0x1d6b Linux Foundation
idProduct 0x0003 3.0 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.34-rc1 xhci_hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:03:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0103 power enable connect
Port 4: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [2.6.34-rc1] Problem using USB 1.1 device on USB 3.0 xhci host controller
2010-03-13 11:01 ` [2.6.34-rc1] Problem using USB 1.1 device on USB 3.0 xhci host controller Sander Eikelenboom
@ 2010-03-15 3:05 ` Libin
2010-03-15 6:04 ` Sarah Sharp
2010-03-15 7:56 ` Sander Eikelenboom
0 siblings, 2 replies; 4+ messages in thread
From: Libin @ 2010-03-15 3:05 UTC (permalink / raw)
To: Sander Eikelenboom; +Cc: Sarah Sharp, linux-usb, linux-kernel, andiry.xu
On Sat, 2010-03-13 at 12:01 +0100, Sander Eikelenboom wrote:
> The patches applied cleanly, but the device doesn't work yet.
> complete dmesg and lsusb -vvv attached.
Thanks for reporting the issue. We will look into the issue. From the
description, it seems the initialization has passed, right? What's the
symptom? Does the system hang?
>
> Highlights from dmesg:
>
> [ 1.738043] usb 9-3: skipped 4 descriptors after interface
> [ 1.738045] usb 9-3: skipped 2 descriptors after interface
> [ 1.738048] usb 9-3: skipped 1 descriptor after endpoint
> [ 1.738050] usb 9-3: skipped 2 descriptors after interface
> [ 1.738053] usb 9-3: skipped 1 descriptor after endpoint
> [ 1.738055] usb 9-3: skipped 2 descriptors after interface
> [ 1.738057] usb 9-3: skipped 1 descriptor after endpoint
> [ 1.738059] usb 9-3: skipped 2 descriptors after interface
> [ 1.738061] usb 9-3: skipped 1 descriptor after endpoint
> [ 1.741021] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
> [ 1.742039] usb 9-3: default language 0x0409
> [ 1.765016] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
> [ 1.766036] usb 9-3: udev 2, busnum 9, minor = 1025
> [ 1.766038] usb 9-3: New USB device found, idVendor=0471, idProduct=0311
> [ 1.766244] usb 9-3: New USB device strings: Mfr=0, Product=0, SerialNumber=1
> [ 1.766448] usb 9-3: SerialNumber: 01680000EA164101
> [ 1.766811] usb 9-3: usb_probe_device
> [ 1.766813] usb 9-3: configuration #1 chosen from 1 choice
> [ 1.767184] usb 9-3: Successful Endpoint Configure command
> [ 1.769035] usb 9-3: adding 9-3:1.0 (config #1, interface 0)
> [ 1.769151] usb 9-3: adding 9-3:1.1 (config #1, interface 1)
> [ 1.769235] usb 9-3: adding 9-3:1.2 (config #1, interface 2)
>
> [ 4.483174] pwc: Philips PCVC740K (ToUCam Pro)/PCVC840 (ToUCam II) USB webcam detected.
> [ 4.515833] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
> [ 4.516894] pwc: Registered as video0.
> [ 4.518834] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint
> [ 4.520834] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint
> [ 4.521051] Philips webcam 9-3:1.1: usb_probe_interface
> [ 4.521053] Philips webcam 9-3:1.1: usb_probe_interface - got id
> [ 4.521058] Philips webcam 9-3:1.2: usb_probe_interface
> [ 4.521060] Philips webcam 9-3:1.2: usb_probe_interface - got id
> [ 4.521073] usbcore: registered new interface driver Philips webcam
>
>
> And when trying to actually grab pictures from the device:
>
> [ 12.957593] usb 9-3: Successful Endpoint Configure command
> [ 12.967542] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7ac74000, num_trbs = 10
> [ 12.967553] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af8c000, num_trbs = 10
> [ 12.985500] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
> [ 20.946116] eth1: no IPv6 routers present
> [ 40.029279] usb 9-3: Successful Endpoint Configure command
> [ 40.039186] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a814000, num_trbs = 10
> [ 40.039198] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b734000, num_trbs = 10
> [ 40.057195] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
> [ 40.216270] usb 9-3: Successful Endpoint Configure command
> [ 40.226183] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a9c0000, num_trbs = 10
> [ 40.226193] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a98c000, num_trbs = 10
> [ 40.245183] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
> [ 40.399261] usb 9-3: Successful Endpoint Configure command
> [ 40.408210] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a9c0000, num_trbs = 10
> [ 40.408220] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a98c000, num_trbs = 10
> [ 47.145805] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
> [ 48.076894] usb 9-3: Successful Endpoint Configure command
> [ 48.086805] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b180000, num_trbs = 10
> [ 48.086816] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b47c000, num_trbs = 10
> [ 48.105803] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
> [ 48.263885] usb 9-3: Successful Endpoint Configure command
> [ 48.273796] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7bba0000, num_trbs = 10
> [ 48.273807] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af6c000, num_trbs = 10
> [ 48.292793] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
> [ 48.446875] usb 9-3: Successful Endpoint Configure command
> [ 48.456784] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7bba0000, num_trbs = 10
> [ 48.456794] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af6c000, num_trbs = 10
> [ 51.778648] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
>
>
>
>
> Saturday, March 13, 2010, 12:25:38 AM, you wrote:
>
> > On Fri, Mar 12, 2010 at 05:43:45PM +0100, Sander Eikelenboom wrote:
> >> Hi Sarah,
> >>
> >> I'm trying to use an USB 1.1 device on a USB 3.0 host controller, but it doesn't seem to work (tested with kernel versions up to 2.6.34-rc1):
> >> - with lsusb I can only see a usb 3.0 root hub (with a USB 2.0 host controller, i'am always seeing the roothubs for lower speeds as well, so maybe this is the problem ?)
> >> - with lsusb I can see the usb 1.1 device connected to the USB 3.0 root hub.
> >> - the driver from the usb 1.1 device get loaded, but it gives errors, and (it's a webcam) doesn't give video.
> >> - the manufacturer claims it should be backwards compatible hardware.
> >>
> >> - Should this work with the current (expirimental) state of the xhci-hcd driver in linux ?
> >>
> >> The hardware is (asus U3S6):
> >> 03:00.0 USB Controller [0c03]: NEC Corporation Device [1033:0194] (rev 03) (prog-if 30)
> >> Subsystem: ASUSTeK Computer Inc. Device [1043:8413]
>
> > From the log files, it looks like your usb 1.1 device is a webcam; is
> > that correct?
>
> >> [ 5.097306] pwc: Philips webcam module version 10.0.13 loaded.
> >> [ 5.097507] pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
> >> [ 5.097859] pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
> >> [ 5.098215] pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
> >> [ 5.098557] pwc: Trace options: 0x0001
> >> [ 5.098576] Philips webcam 9-3:1.0: usb_probe_interface
> >> [ 5.098578] Philips webcam 9-3:1.0: usb_probe_interface - got id
> > ...
> >> [ 13.116489] pwc: isoc_init() submit_urb 0 failed with error -22
>
> > Webcams have isochronous endpoints, and the xHCI driver doesn't support
> > isochronous transfers yet. There are patches to add isochronous
> > support, but they're still under going review. They missed the 2.6.34
> > merge window, so I'm not sure if they'll make it into 2.6.34 or 2.6.35.
> > If you want to try them out, the latest versions of the patches are
> > here:
>
> > http://marc.info/?l=linux-usb&m=126838645617885&w=2
> > http://marc.info/?l=linux-usb&m=126838648717923&w=2
> > http://marc.info/?l=linux-usb&m=126838649217932&w=2
>
> > Let me know if they work for you.
>
> > Sarah Sharp
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [2.6.34-rc1] Problem using USB 1.1 device on USB 3.0 xhci host controller
2010-03-15 3:05 ` Libin
@ 2010-03-15 6:04 ` Sarah Sharp
2010-03-15 7:56 ` Sander Eikelenboom
1 sibling, 0 replies; 4+ messages in thread
From: Sarah Sharp @ 2010-03-15 6:04 UTC (permalink / raw)
To: Libin; +Cc: Sander Eikelenboom, linux-usb, linux-kernel, andiry.xu
On Mon, Mar 15, 2010 at 11:05:39AM +0800, Libin wrote:
> On Sat, 2010-03-13 at 12:01 +0100, Sander Eikelenboom wrote:
> > The patches applied cleanly, but the device doesn't work yet.
> > complete dmesg and lsusb -vvv attached.
>
> Thanks for reporting the issue. We will look into the issue. From the
> description, it seems the initialization has passed, right? What's the
> symptom? Does the system hang?
>From the log, it looks like the USB driver is submitting URBs, but the
xHCI driver is seeing spurious events. It could be that the hardware is
sending spurious events, but it's more likely that the xHCI driver's
isochronous URB completion isn't correct. If you give back the URB too
soon, and the event ring handler finds the endpoint's TD list is empty,
you'll see lines like this:
> > [ 12.985500] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
If you're giving the URB back too soon, that would also explain why the
device doesn't seem to work -- the driver would be seeing uncompleted
packets (and possibly retrying).
But we can't be sure without more information about what the spurious
event looks like.
Sander, can you recompile with CONFIG_USB_XHCI_HCD_DEBUGGING set to yes
and retry with your device?
Thanks,
Sarah Sharp
>
> >
> > Highlights from dmesg:
> >
> > [ 1.738043] usb 9-3: skipped 4 descriptors after interface
> > [ 1.738045] usb 9-3: skipped 2 descriptors after interface
> > [ 1.738048] usb 9-3: skipped 1 descriptor after endpoint
> > [ 1.738050] usb 9-3: skipped 2 descriptors after interface
> > [ 1.738053] usb 9-3: skipped 1 descriptor after endpoint
> > [ 1.738055] usb 9-3: skipped 2 descriptors after interface
> > [ 1.738057] usb 9-3: skipped 1 descriptor after endpoint
> > [ 1.738059] usb 9-3: skipped 2 descriptors after interface
> > [ 1.738061] usb 9-3: skipped 1 descriptor after endpoint
> > [ 1.741021] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
> > [ 1.742039] usb 9-3: default language 0x0409
> > [ 1.765016] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
> > [ 1.766036] usb 9-3: udev 2, busnum 9, minor = 1025
> > [ 1.766038] usb 9-3: New USB device found, idVendor=0471, idProduct=0311
> > [ 1.766244] usb 9-3: New USB device strings: Mfr=0, Product=0, SerialNumber=1
> > [ 1.766448] usb 9-3: SerialNumber: 01680000EA164101
> > [ 1.766811] usb 9-3: usb_probe_device
> > [ 1.766813] usb 9-3: configuration #1 chosen from 1 choice
> > [ 1.767184] usb 9-3: Successful Endpoint Configure command
> > [ 1.769035] usb 9-3: adding 9-3:1.0 (config #1, interface 0)
> > [ 1.769151] usb 9-3: adding 9-3:1.1 (config #1, interface 1)
> > [ 1.769235] usb 9-3: adding 9-3:1.2 (config #1, interface 2)
> >
> > [ 4.483174] pwc: Philips PCVC740K (ToUCam Pro)/PCVC840 (ToUCam II) USB webcam detected.
> > [ 4.515833] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
> > [ 4.516894] pwc: Registered as video0.
> > [ 4.518834] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint
> > [ 4.520834] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint
> > [ 4.521051] Philips webcam 9-3:1.1: usb_probe_interface
> > [ 4.521053] Philips webcam 9-3:1.1: usb_probe_interface - got id
> > [ 4.521058] Philips webcam 9-3:1.2: usb_probe_interface
> > [ 4.521060] Philips webcam 9-3:1.2: usb_probe_interface - got id
> > [ 4.521073] usbcore: registered new interface driver Philips webcam
> >
> >
> > And when trying to actually grab pictures from the device:
> >
> > [ 12.957593] usb 9-3: Successful Endpoint Configure command
> > [ 12.967542] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7ac74000, num_trbs = 10
> > [ 12.967553] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af8c000, num_trbs = 10
> > [ 12.985500] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
> > [ 20.946116] eth1: no IPv6 routers present
> > [ 40.029279] usb 9-3: Successful Endpoint Configure command
> > [ 40.039186] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a814000, num_trbs = 10
> > [ 40.039198] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b734000, num_trbs = 10
> > [ 40.057195] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
> > [ 40.216270] usb 9-3: Successful Endpoint Configure command
> > [ 40.226183] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a9c0000, num_trbs = 10
> > [ 40.226193] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a98c000, num_trbs = 10
> > [ 40.245183] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
> > [ 40.399261] usb 9-3: Successful Endpoint Configure command
> > [ 40.408210] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a9c0000, num_trbs = 10
> > [ 40.408220] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a98c000, num_trbs = 10
> > [ 47.145805] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
> > [ 48.076894] usb 9-3: Successful Endpoint Configure command
> > [ 48.086805] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b180000, num_trbs = 10
> > [ 48.086816] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b47c000, num_trbs = 10
> > [ 48.105803] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
> > [ 48.263885] usb 9-3: Successful Endpoint Configure command
> > [ 48.273796] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7bba0000, num_trbs = 10
> > [ 48.273807] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af6c000, num_trbs = 10
> > [ 48.292793] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
> > [ 48.446875] usb 9-3: Successful Endpoint Configure command
> > [ 48.456784] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7bba0000, num_trbs = 10
> > [ 48.456794] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af6c000, num_trbs = 10
> > [ 51.778648] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
> >
> >
> >
> >
> > Saturday, March 13, 2010, 12:25:38 AM, you wrote:
> >
> > > On Fri, Mar 12, 2010 at 05:43:45PM +0100, Sander Eikelenboom wrote:
> > >> Hi Sarah,
> > >>
> > >> I'm trying to use an USB 1.1 device on a USB 3.0 host controller, but it doesn't seem to work (tested with kernel versions up to 2.6.34-rc1):
> > >> - with lsusb I can only see a usb 3.0 root hub (with a USB 2.0 host controller, i'am always seeing the roothubs for lower speeds as well, so maybe this is the problem ?)
> > >> - with lsusb I can see the usb 1.1 device connected to the USB 3.0 root hub.
> > >> - the driver from the usb 1.1 device get loaded, but it gives errors, and (it's a webcam) doesn't give video.
> > >> - the manufacturer claims it should be backwards compatible hardware.
> > >>
> > >> - Should this work with the current (expirimental) state of the xhci-hcd driver in linux ?
> > >>
> > >> The hardware is (asus U3S6):
> > >> 03:00.0 USB Controller [0c03]: NEC Corporation Device [1033:0194] (rev 03) (prog-if 30)
> > >> Subsystem: ASUSTeK Computer Inc. Device [1043:8413]
> >
> > > From the log files, it looks like your usb 1.1 device is a webcam; is
> > > that correct?
> >
> > >> [ 5.097306] pwc: Philips webcam module version 10.0.13 loaded.
> > >> [ 5.097507] pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
> > >> [ 5.097859] pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
> > >> [ 5.098215] pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
> > >> [ 5.098557] pwc: Trace options: 0x0001
> > >> [ 5.098576] Philips webcam 9-3:1.0: usb_probe_interface
> > >> [ 5.098578] Philips webcam 9-3:1.0: usb_probe_interface - got id
> > > ...
> > >> [ 13.116489] pwc: isoc_init() submit_urb 0 failed with error -22
> >
> > > Webcams have isochronous endpoints, and the xHCI driver doesn't support
> > > isochronous transfers yet. There are patches to add isochronous
> > > support, but they're still under going review. They missed the 2.6.34
> > > merge window, so I'm not sure if they'll make it into 2.6.34 or 2.6.35.
> > > If you want to try them out, the latest versions of the patches are
> > > here:
> >
> > > http://marc.info/?l=linux-usb&m=126838645617885&w=2
> > > http://marc.info/?l=linux-usb&m=126838648717923&w=2
> > > http://marc.info/?l=linux-usb&m=126838649217932&w=2
> >
> > > Let me know if they work for you.
> >
> > > Sarah Sharp
>
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [2.6.34-rc1] Problem using USB 1.1 device on USB 3.0 xhci host controller
2010-03-15 3:05 ` Libin
2010-03-15 6:04 ` Sarah Sharp
@ 2010-03-15 7:56 ` Sander Eikelenboom
1 sibling, 0 replies; 4+ messages in thread
From: Sander Eikelenboom @ 2010-03-15 7:56 UTC (permalink / raw)
To: Libin; +Cc: Sarah Sharp, linux-usb, linux-kernel, andiry.xu
Hello Libin,
Nope, no system hang, the only symptom is that the device is not working, (v4l application seems to wait for video frames but they do not arrive).
-
Sander
Monday, March 15, 2010, 4:05:39 AM, you wrote:
> On Sat, 2010-03-13 at 12:01 +0100, Sander Eikelenboom wrote:
>> The patches applied cleanly, but the device doesn't work yet.
>> complete dmesg and lsusb -vvv attached.
> Thanks for reporting the issue. We will look into the issue. From the
> description, it seems the initialization has passed, right? What's the
> symptom? Does the system hang?
>>
>> Highlights from dmesg:
>>
>> [ 1.738043] usb 9-3: skipped 4 descriptors after interface
>> [ 1.738045] usb 9-3: skipped 2 descriptors after interface
>> [ 1.738048] usb 9-3: skipped 1 descriptor after endpoint
>> [ 1.738050] usb 9-3: skipped 2 descriptors after interface
>> [ 1.738053] usb 9-3: skipped 1 descriptor after endpoint
>> [ 1.738055] usb 9-3: skipped 2 descriptors after interface
>> [ 1.738057] usb 9-3: skipped 1 descriptor after endpoint
>> [ 1.738059] usb 9-3: skipped 2 descriptors after interface
>> [ 1.738061] usb 9-3: skipped 1 descriptor after endpoint
>> [ 1.741021] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
>> [ 1.742039] usb 9-3: default language 0x0409
>> [ 1.765016] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
>> [ 1.766036] usb 9-3: udev 2, busnum 9, minor = 1025
>> [ 1.766038] usb 9-3: New USB device found, idVendor=0471, idProduct=0311
>> [ 1.766244] usb 9-3: New USB device strings: Mfr=0, Product=0, SerialNumber=1
>> [ 1.766448] usb 9-3: SerialNumber: 01680000EA164101
>> [ 1.766811] usb 9-3: usb_probe_device
>> [ 1.766813] usb 9-3: configuration #1 chosen from 1 choice
>> [ 1.767184] usb 9-3: Successful Endpoint Configure command
>> [ 1.769035] usb 9-3: adding 9-3:1.0 (config #1, interface 0)
>> [ 1.769151] usb 9-3: adding 9-3:1.1 (config #1, interface 1)
>> [ 1.769235] usb 9-3: adding 9-3:1.2 (config #1, interface 2)
>>
>> [ 4.483174] pwc: Philips PCVC740K (ToUCam Pro)/PCVC840 (ToUCam II) USB webcam detected.
>> [ 4.515833] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
>> [ 4.516894] pwc: Registered as video0.
>> [ 4.518834] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint
>> [ 4.520834] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint
>> [ 4.521051] Philips webcam 9-3:1.1: usb_probe_interface
>> [ 4.521053] Philips webcam 9-3:1.1: usb_probe_interface - got id
>> [ 4.521058] Philips webcam 9-3:1.2: usb_probe_interface
>> [ 4.521060] Philips webcam 9-3:1.2: usb_probe_interface - got id
>> [ 4.521073] usbcore: registered new interface driver Philips webcam
>>
>>
>> And when trying to actually grab pictures from the device:
>>
>> [ 12.957593] usb 9-3: Successful Endpoint Configure command
>> [ 12.967542] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7ac74000, num_trbs = 10
>> [ 12.967553] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af8c000, num_trbs = 10
>> [ 12.985500] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
>> [ 20.946116] eth1: no IPv6 routers present
>> [ 40.029279] usb 9-3: Successful Endpoint Configure command
>> [ 40.039186] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a814000, num_trbs = 10
>> [ 40.039198] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b734000, num_trbs = 10
>> [ 40.057195] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
>> [ 40.216270] usb 9-3: Successful Endpoint Configure command
>> [ 40.226183] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a9c0000, num_trbs = 10
>> [ 40.226193] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a98c000, num_trbs = 10
>> [ 40.245183] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
>> [ 40.399261] usb 9-3: Successful Endpoint Configure command
>> [ 40.408210] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a9c0000, num_trbs = 10
>> [ 40.408220] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7a98c000, num_trbs = 10
>> [ 47.145805] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
>> [ 48.076894] usb 9-3: Successful Endpoint Configure command
>> [ 48.086805] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b180000, num_trbs = 10
>> [ 48.086816] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7b47c000, num_trbs = 10
>> [ 48.105803] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
>> [ 48.263885] usb 9-3: Successful Endpoint Configure command
>> [ 48.273796] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7bba0000, num_trbs = 10
>> [ 48.273807] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af6c000, num_trbs = 10
>> [ 48.292793] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
>> [ 48.446875] usb 9-3: Successful Endpoint Configure command
>> [ 48.456784] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7bba0000, num_trbs = 10
>> [ 48.456794] usb 9-3: ep 0x85 - urb len = 0x2580 (9600), addr = 0x7af6c000, num_trbs = 10
>> [ 51.778648] xhci_hcd 0000:03:00.0: WARN Event TRB for slot 1 ep 10 with no TDs queued?
>>
>>
>>
>>
>> Saturday, March 13, 2010, 12:25:38 AM, you wrote:
>>
>> > On Fri, Mar 12, 2010 at 05:43:45PM +0100, Sander Eikelenboom wrote:
>> >> Hi Sarah,
>> >>
>> >> I'm trying to use an USB 1.1 device on a USB 3.0 host controller, but it doesn't seem to work (tested with kernel versions up to 2.6.34-rc1):
>> >> - with lsusb I can only see a usb 3.0 root hub (with a USB 2.0 host controller, i'am always seeing the roothubs for lower speeds as well, so maybe this is the problem ?)
>> >> - with lsusb I can see the usb 1.1 device connected to the USB 3.0 root hub.
>> >> - the driver from the usb 1.1 device get loaded, but it gives errors, and (it's a webcam) doesn't give video.
>> >> - the manufacturer claims it should be backwards compatible hardware.
>> >>
>> >> - Should this work with the current (expirimental) state of the xhci-hcd driver in linux ?
>> >>
>> >> The hardware is (asus U3S6):
>> >> 03:00.0 USB Controller [0c03]: NEC Corporation Device [1033:0194] (rev 03) (prog-if 30)
>> >> Subsystem: ASUSTeK Computer Inc. Device [1043:8413]
>>
>> > From the log files, it looks like your usb 1.1 device is a webcam; is
>> > that correct?
>>
>> >> [ 5.097306] pwc: Philips webcam module version 10.0.13 loaded.
>> >> [ 5.097507] pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
>> >> [ 5.097859] pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
>> >> [ 5.098215] pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
>> >> [ 5.098557] pwc: Trace options: 0x0001
>> >> [ 5.098576] Philips webcam 9-3:1.0: usb_probe_interface
>> >> [ 5.098578] Philips webcam 9-3:1.0: usb_probe_interface - got id
>> > ...
>> >> [ 13.116489] pwc: isoc_init() submit_urb 0 failed with error -22
>>
>> > Webcams have isochronous endpoints, and the xHCI driver doesn't support
>> > isochronous transfers yet. There are patches to add isochronous
>> > support, but they're still under going review. They missed the 2.6.34
>> > merge window, so I'm not sure if they'll make it into 2.6.34 or 2.6.35.
>> > If you want to try them out, the latest versions of the patches are
>> > here:
>>
>> > http://marc.info/?l=linux-usb&m=126838645617885&w=2
>> > http://marc.info/?l=linux-usb&m=126838648717923&w=2
>> > http://marc.info/?l=linux-usb&m=126838649217932&w=2
>>
>> > Let me know if they work for you.
>>
>> > Sarah Sharp
--
Best regards,
Sander mailto:linux@eikelenboom.it
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2010-03-15 7:56 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <1751702501.20100312174345@eikelenboom.it>
[not found] ` <20100312232538.GA13353@xanatos>
2010-03-13 11:01 ` [2.6.34-rc1] Problem using USB 1.1 device on USB 3.0 xhci host controller Sander Eikelenboom
2010-03-15 3:05 ` Libin
2010-03-15 6:04 ` Sarah Sharp
2010-03-15 7:56 ` Sander Eikelenboom
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®