* [PATCH] DA9052 Linux device drivers [9/9]
@ 2010-05-19 12:46 David Dajun Chen
2010-05-19 18:06 ` Randy Dunlap
0 siblings, 1 reply; 2+ messages in thread
From: David Dajun Chen @ 2010-05-19 12:46 UTC (permalink / raw)
To: linux-kernel
Dear sir/madam,
The attached is the feature CONFIG part of the device drivers newly developed for DA9052 Power Management IC from Dialog Semiconductor.
Should you have any queries or comments please feel free to contact me.
Regards
Dr. David Dajun Chen
Dialog Semiconductor Ltd.
Delta 200, Welton Road
Delta Business Park
Swindon
Wiltshire SN5 7XB
UK
Telephone: (+44) 01793-757714
Mobile: (+44) 07917015477
Fax: (+44) 01793-758000
===========================================================================
diff -Naur linux-2.6.33.2/drivers/Makefile linux-2.6.33.2_patch/drivers/Makefile
--- linux-2.6.33.2/drivers/Makefile 2010-04-02 04:02:33.000000000 +0500
+++ linux-2.6.33.2_patch/drivers/Makefile 2010-05-12 09:44:14.000000000 +0500
@@ -5,13 +5,15 @@
# Rewritten to use lists instead of if-statements.
#
+ifneq ($(CONFIG_MFD_DA9052),y)
obj-y += gpio/
+endif
+
obj-$(CONFIG_PCI) += pci/
obj-$(CONFIG_PARISC) += parisc/
obj-$(CONFIG_RAPIDIO) += rapidio/
obj-y += video/
obj-$(CONFIG_ACPI) += acpi/
-obj-$(CONFIG_SFI) += sfi/
# PnP must come after ACPI since it will eventually need to check if acpi
# was used and do nothing if so
obj-$(CONFIG_PNP) += pnp/
@@ -19,9 +21,6 @@
obj-$(CONFIG_XEN) += xen/
-# regulators early, since some subsystems rely on them to initialize
-obj-$(CONFIG_REGULATOR) += regulator/
-
# char/ comes before serial/ etc so that the VT console is the boot-time
# default.
obj-y += char/
@@ -37,22 +36,27 @@
obj-y += serial/
obj-$(CONFIG_PARPORT) += parport/
-obj-y += base/ block/ misc/ mfd/
+
+ifneq ($(CONFIG_MFD_DA9052),y)
+obj-y += base/ block/ misc/ mfd/ net/ media/
+else
+obj-y += base/ block/ misc/ net/ media/
+endif
+
obj-$(CONFIG_NUBUS) += nubus/
+obj-$(CONFIG_ATM) += atm/
obj-y += macintosh/
obj-$(CONFIG_IDE) += ide/
obj-$(CONFIG_SCSI) += scsi/
obj-$(CONFIG_ATA) += ata/
-obj-$(CONFIG_MTD) += mtd/
-obj-$(CONFIG_SPI) += spi/
-obj-y += net/
-obj-$(CONFIG_ATM) += atm/
obj-$(CONFIG_FUSION) += message/
obj-$(CONFIG_FIREWIRE) += firewire/
obj-y += ieee1394/
obj-$(CONFIG_UIO) += uio/
obj-y += cdrom/
obj-y += auxdisplay/
+obj-$(CONFIG_MTD) += mtd/
+obj-$(CONFIG_SPI) += spi/
obj-$(CONFIG_PCCARD) += pcmcia/
obj-$(CONFIG_DIO) += dio/
obj-$(CONFIG_SBUS) += sbus/
@@ -62,23 +66,37 @@
obj-$(CONFIG_PARIDE) += block/paride/
obj-$(CONFIG_TC) += tc/
obj-$(CONFIG_UWB) += uwb/
-obj-$(CONFIG_USB_OTG_UTILS) += usb/otg/
obj-$(CONFIG_USB) += usb/
obj-$(CONFIG_USB_MUSB_HDRC) += usb/musb/
obj-$(CONFIG_PCI) += usb/
obj-$(CONFIG_USB_GADGET) += usb/gadget/
obj-$(CONFIG_SERIO) += input/serio/
obj-$(CONFIG_GAMEPORT) += input/gameport/
+
+ifneq ($(CONFIG_MFD_DA9052),y)
obj-$(CONFIG_INPUT) += input/
+endif
+
obj-$(CONFIG_I2O) += message/
+
+ifneq ($(CONFIG_MFD_DA9052),y)
obj-$(CONFIG_RTC_LIB) += rtc/
-obj-y += i2c/ media/
-obj-$(CONFIG_PPS) += pps/
+endif
+
+obj-y += i2c/
obj-$(CONFIG_W1) += w1/
+
+ifneq ($(CONFIG_MFD_DA9052),y)
obj-$(CONFIG_POWER_SUPPLY) += power/
+endif
+
obj-$(CONFIG_HWMON) += hwmon/
obj-$(CONFIG_THERMAL) += thermal/
+
+ifeq ($(CONFIG_MFD_DA9052),n)
obj-$(CONFIG_WATCHDOG) += watchdog/
+endif
+
obj-$(CONFIG_PHONE) += telephony/
obj-$(CONFIG_MD) += md/
obj-$(CONFIG_BT) += bluetooth/
@@ -93,7 +111,11 @@
obj-y += idle/
obj-$(CONFIG_MMC) += mmc/
obj-$(CONFIG_MEMSTICK) += memstick/
+
+ifneq ($(CONFIG_MFD_DA9052),y)
obj-$(CONFIG_NEW_LEDS) += leds/
+endif
+
obj-$(CONFIG_INFINIBAND) += infiniband/
obj-$(CONFIG_SGI_SN) += sn/
obj-y += firmware/
@@ -107,7 +129,20 @@
obj-$(CONFIG_OF) += of/
obj-$(CONFIG_SSB) += ssb/
obj-$(CONFIG_VIRTIO) += virtio/
-obj-$(CONFIG_VLYNQ) += vlynq/
+
+ifneq ($(CONFIG_MFD_DA9052),y)
+obj-$(CONFIG_REGULATOR) += regulator/
+endif
+
obj-$(CONFIG_STAGING) += staging/
-obj-y += platform/
-obj-y += ieee802154/
+
+ifeq ($(CONFIG_MFD_DA9052),y)
+obj-y += mfd/
+obj-y += gpio/
+obj-$(CONFIG_INPUT) += input/
+obj-$(CONFIG_RTC_LIB) += rtc/
+obj-$(CONFIG_POWER_SUPPLY) += power/
+obj-$(CONFIG_WATCHDOG) += watchdog/
+obj-$(CONFIG_NEW_LEDS) += leds/
+obj-$(CONFIG_REGULATOR) += regulator/
+endif
Legal Disclaimer: This e-mail communication (and any attachment/s) is confidential and contains proprietary information,
some or all of which may be legally privileged. It is intended solely for the use of the individual or entity to which it
is addressed. Access to this email by anyone else is unauthorized. If you are not the intended recipient, any disclosure,
copying, distribution or any action taken or omitted to be taken in reliance on it, is prohibited and may be unlawful.
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: [PATCH] DA9052 Linux device drivers [9/9]
2010-05-19 12:46 [PATCH] DA9052 Linux device drivers [9/9] David Dajun Chen
@ 2010-05-19 18:06 ` Randy Dunlap
0 siblings, 0 replies; 2+ messages in thread
From: Randy Dunlap @ 2010-05-19 18:06 UTC (permalink / raw)
To: David Dajun Chen; +Cc: linux-kernel
On Wed, 19 May 2010 13:46:00 +0100 David Dajun Chen wrote:
> Dear sir/madam,
>
> The attached is the feature CONFIG part of the device drivers newly developed for DA9052 Power Management IC from Dialog Semiconductor.
>
> Should you have any queries or comments please feel free to contact me.
Were all of these changes meant to be here?
If so, they need justification.
> ===========================================================================
>
>
> diff -Naur linux-2.6.33.2/drivers/Makefile linux-2.6.33.2_patch/drivers/Makefile
> --- linux-2.6.33.2/drivers/Makefile 2010-04-02 04:02:33.000000000 +0500
> +++ linux-2.6.33.2_patch/drivers/Makefile 2010-05-12 09:44:14.000000000 +0500
> @@ -5,13 +5,15 @@
> # Rewritten to use lists instead of if-statements.
> #
>
> +ifneq ($(CONFIG_MFD_DA9052),y)
> obj-y += gpio/
> +endif
> +
> obj-$(CONFIG_PCI) += pci/
> obj-$(CONFIG_PARISC) += parisc/
> obj-$(CONFIG_RAPIDIO) += rapidio/
> obj-y += video/
> obj-$(CONFIG_ACPI) += acpi/
> -obj-$(CONFIG_SFI) += sfi/
> # PnP must come after ACPI since it will eventually need to check if acpi
> # was used and do nothing if so
> obj-$(CONFIG_PNP) += pnp/
> @@ -19,9 +21,6 @@
>
> obj-$(CONFIG_XEN) += xen/
>
> -# regulators early, since some subsystems rely on them to initialize
> -obj-$(CONFIG_REGULATOR) += regulator/
> -
> # char/ comes before serial/ etc so that the VT console is the boot-time
> # default.
> obj-y += char/
> @@ -37,22 +36,27 @@
>
> obj-y += serial/
> obj-$(CONFIG_PARPORT) += parport/
> -obj-y += base/ block/ misc/ mfd/
> +
> +ifneq ($(CONFIG_MFD_DA9052),y)
> +obj-y += base/ block/ misc/ mfd/ net/ media/
> +else
> +obj-y += base/ block/ misc/ net/ media/
> +endif
> +
> obj-$(CONFIG_NUBUS) += nubus/
> +obj-$(CONFIG_ATM) += atm/
> obj-y += macintosh/
> obj-$(CONFIG_IDE) += ide/
> obj-$(CONFIG_SCSI) += scsi/
> obj-$(CONFIG_ATA) += ata/
> -obj-$(CONFIG_MTD) += mtd/
> -obj-$(CONFIG_SPI) += spi/
> -obj-y += net/
> -obj-$(CONFIG_ATM) += atm/
> obj-$(CONFIG_FUSION) += message/
> obj-$(CONFIG_FIREWIRE) += firewire/
> obj-y += ieee1394/
> obj-$(CONFIG_UIO) += uio/
> obj-y += cdrom/
> obj-y += auxdisplay/
> +obj-$(CONFIG_MTD) += mtd/
> +obj-$(CONFIG_SPI) += spi/
> obj-$(CONFIG_PCCARD) += pcmcia/
> obj-$(CONFIG_DIO) += dio/
> obj-$(CONFIG_SBUS) += sbus/
> @@ -62,23 +66,37 @@
> obj-$(CONFIG_PARIDE) += block/paride/
> obj-$(CONFIG_TC) += tc/
> obj-$(CONFIG_UWB) += uwb/
> -obj-$(CONFIG_USB_OTG_UTILS) += usb/otg/
> obj-$(CONFIG_USB) += usb/
> obj-$(CONFIG_USB_MUSB_HDRC) += usb/musb/
> obj-$(CONFIG_PCI) += usb/
> obj-$(CONFIG_USB_GADGET) += usb/gadget/
> obj-$(CONFIG_SERIO) += input/serio/
> obj-$(CONFIG_GAMEPORT) += input/gameport/
> +
> +ifneq ($(CONFIG_MFD_DA9052),y)
> obj-$(CONFIG_INPUT) += input/
> +endif
> +
> obj-$(CONFIG_I2O) += message/
> +
> +ifneq ($(CONFIG_MFD_DA9052),y)
> obj-$(CONFIG_RTC_LIB) += rtc/
> -obj-y += i2c/ media/
> -obj-$(CONFIG_PPS) += pps/
> +endif
> +
> +obj-y += i2c/
> obj-$(CONFIG_W1) += w1/
> +
> +ifneq ($(CONFIG_MFD_DA9052),y)
> obj-$(CONFIG_POWER_SUPPLY) += power/
> +endif
> +
> obj-$(CONFIG_HWMON) += hwmon/
> obj-$(CONFIG_THERMAL) += thermal/
> +
> +ifeq ($(CONFIG_MFD_DA9052),n)
> obj-$(CONFIG_WATCHDOG) += watchdog/
> +endif
> +
> obj-$(CONFIG_PHONE) += telephony/
> obj-$(CONFIG_MD) += md/
> obj-$(CONFIG_BT) += bluetooth/
> @@ -93,7 +111,11 @@
> obj-y += idle/
> obj-$(CONFIG_MMC) += mmc/
> obj-$(CONFIG_MEMSTICK) += memstick/
> +
> +ifneq ($(CONFIG_MFD_DA9052),y)
> obj-$(CONFIG_NEW_LEDS) += leds/
> +endif
> +
> obj-$(CONFIG_INFINIBAND) += infiniband/
> obj-$(CONFIG_SGI_SN) += sn/
> obj-y += firmware/
> @@ -107,7 +129,20 @@
> obj-$(CONFIG_OF) += of/
> obj-$(CONFIG_SSB) += ssb/
> obj-$(CONFIG_VIRTIO) += virtio/
> -obj-$(CONFIG_VLYNQ) += vlynq/
> +
> +ifneq ($(CONFIG_MFD_DA9052),y)
> +obj-$(CONFIG_REGULATOR) += regulator/
> +endif
> +
> obj-$(CONFIG_STAGING) += staging/
> -obj-y += platform/
> -obj-y += ieee802154/
> +
> +ifeq ($(CONFIG_MFD_DA9052),y)
> +obj-y += mfd/
> +obj-y += gpio/
> +obj-$(CONFIG_INPUT) += input/
> +obj-$(CONFIG_RTC_LIB) += rtc/
> +obj-$(CONFIG_POWER_SUPPLY) += power/
> +obj-$(CONFIG_WATCHDOG) += watchdog/
> +obj-$(CONFIG_NEW_LEDS) += leds/
> +obj-$(CONFIG_REGULATOR) += regulator/
> +endif
---
~Randy
*** Remember to use Documentation/SubmitChecklist when testing your code ***
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2010-05-19 18:08 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-05-19 12:46 [PATCH] DA9052 Linux device drivers [9/9] David Dajun Chen
2010-05-19 18:06 ` Randy Dunlap
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome