PROBLEM: additional serial ports on MS9830 board do not work (IRQ problems)

[Jan Kandziora <jjj@gmx.de>]

[-- Attachment #1: Type: text/plain, Size: 2869 bytes --]

Hello,

Summary:        additional serial ports on MS9830 board do not work
Keywords:       serial
Kernel version: 2.6.35.4

I have problems with the IRQs of a MS9830 Mini ITX board. The board has 1 
serial port on a DB9 connector and 4 additional ones on internal connectors, 
which can also be powered. The computer has a touchscreen controller 
connected to one of those internal ports.

The internal ports seem to be special as they don't work correctly. Depending 
on BIOS settings, I either don't get any IRQs from them or I get IRQs but the 
serial driver doesn't claim them.

To make the bug hunt simpler, I disabled all ports but one of the internal 
ones, which I've set to 0x3F8/IRQ4. Then I open the port with "od /dev/ttyS0" 
and touch the screen. After some seconds I get

<3>irq 4: nobody cared (try booting with the "irqpoll" option)
<4>Pid: 3923, comm: exe Not tainted 2.6.35.4 #1
<4>Call Trace:
<4> [<c103a950>] __report_bad_irq+0x2e/0x6f
<4> [<c103aa81>] note_interrupt+0xf0/0x147
<4> [<c103b042>] handle_level_irq+0x6d/0x99
<4> [<c1003b32>] handle_irq+0x1a/0x20
<4> [<c1003883>] do_IRQ+0x33/0x75
<4> [<c1002b69>] common_interrupt+0x29/0x30
<4> [<c101d8c8>] ? __do_softirq+0x34/0xca
<4> [<c101d983>] do_softirq+0x25/0x2a
<4> [<c101da43>] irq_exit+0x28/0x57
<4> [<c10038b0>] do_IRQ+0x60/0x75
<4> [<c1002b69>] common_interrupt+0x29/0x30
<4> [<c103007b>] ? timecompare_offset+0x9c/0x2c6
<4> [<c103a3ec>] ? __setup_irq+0x1d8/0x259
<4> [<c103a510>] request_threaded_irq+0xa3/0xd0
<4> [<c119f173>] ? serial8250_interrupt+0x0/0xb2
<4> [<c119ec07>] serial8250_startup+0x3f5/0x53d
<4> [<c119bfa9>] uart_startup+0x6e/0x101
<4> [<c119ca89>] uart_open+0xff/0x2ac
<4> [<c114fee7>] ? tty_init_dev+0xb7/0xf0
<4> [<c11501ab>] tty_open+0x28b/0x354
<4> [<c106336e>] chrdev_open+0xc0/0xd7
<4> [<c1060141>] __dentry_open+0xd1/0x1a7
<4> [<c10602ad>] nameidata_to_filp+0x29/0x3d
<4> [<c10632ae>] ? chrdev_open+0x0/0xd7
<4> [<c1068a92>] do_last+0x3d1/0x4d1
<4> [<c106a13f>] do_filp_open+0x17c/0x41e
<4> [<c10124c0>] ? do_page_fault+0x2a1/0x2cf
<4> [<c105ff43>] do_sys_open+0x48/0x116
<4> [<c1060053>] sys_open+0x1e/0x26
<4> [<c1002650>] sysenter_do_call+0x12/0x26
<3>handlers:
<3>[<c119f173>] (serial8250_interrupt+0x0/0xb2)
<0>Disabling IRQ #4
<4>ttyS0: 1 input overrun(s)
<6>usb 4-1: new full speed USB device using uhci_hcd and address 2
<4>ttyS0: 10 input overrun(s)

in dmesg and some data from the touch controller. But it's very jumpy without 
interrupts, hardly useable.

I tried the suggested option "irqpoll", but then the computer just freezes 
when I do "od /dev/ttyS0" and touch the screen. No kernel panic, just a hard 
freeze. I tried "acpi=noirq", "acpi=off" and disabling the APIC in the BIOS 
setup, too. None of these made the serial irq work.

Can you give me any useful pointers what to try next? Kernel configuration is 
attached.

Kind regards

	Jan

[-- Attachment #2: config.gz --]
[-- Type: application/x-gzip, Size: 12780 bytes --]