From: Oleg Nesterov <oleg@redhat.com>
To: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>,
"Paul E. McKenney" <paulmck@linux.vnet.ibm.com>,
Peter Zijlstra <peterz@infradead.org>,
Rik van Riel <riel@redhat.com>,
Thomas Gleixner <tglx@linutronix.de>,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH 1/2] signal: simplify deadlock-avoidance in lock_task_sighand()
Date: Mon, 22 Sep 2014 21:11:30 +0200 [thread overview]
Message-ID: <20140922191130.GA4527@redhat.com> (raw)
In-Reply-To: <20140922145828.4d06108a@gandalf.local.home>
On 09/22, Steven Rostedt wrote:
>
> On Mon, 22 Sep 2014 18:44:37 +0200
> Oleg Nesterov <oleg@redhat.com> wrote:
>
> > __lock_task_sighand() does local_irq_save() to prevent the potential
> > deadlock, we can use preempt_disable() with the same effect. And in
> > this case we can do preempt_disable/enable + rcu_read_lock/unlock only
> > once outside of the main loop and simplify the code. This also shaves
> > 112 bytes from signal.o.
> >
> > With this patch the main loop runs with preemption disabled, but this
> > should be fine because restart is very unlikely: it can only happen if
> > we race with de_thread() and ->sighand is shared. And the latter is only
> > possible if CLONE_SIGHAND was used without CLONE_THREAD, most probably
> > nobody does this nowadays.
> >
> > Signed-off-by: Oleg Nesterov <oleg@redhat.com>
> > ---
> > kernel/signal.c | 31 +++++++++++++------------------
> > 1 files changed, 13 insertions(+), 18 deletions(-)
> >
> > diff --git a/kernel/signal.c b/kernel/signal.c
> > index 8f0876f..61a1f55 100644
> > --- a/kernel/signal.c
> > +++ b/kernel/signal.c
> > @@ -1261,30 +1261,25 @@ struct sighand_struct *__lock_task_sighand(struct task_struct *tsk,
> > unsigned long *flags)
> > {
> > struct sighand_struct *sighand;
> > -
> > + /*
> > + * We are going to do rcu_read_unlock() under spin_lock_irqsave().
> > + * Make sure we can not be preempted after rcu_read_lock(), see
> > + * rcu_read_unlock() comment header for details.
> > + */
> > + preempt_disable();
>
> The sad part is, this is going to break -rt.
Hmm, why??
> That
> is, is -rt susceptible to this deadlock as well?
In fact this deadlock is not really possible in any case, scheduler locks
should be fine under ->siglock (for example, signal_wake_up() is called
under this lock).
But, the comment above rcu_read_unlock() says:
Given that the set of locks acquired by rt_mutex_unlock() might change
at any time, a somewhat more future-proofed approach is to make sure
that that preemption never happens ...
so this patch doesn't try to change the rules.
But perhaps we can simply remove this preempt_disable/enable?
Or. We can shift rcu_read_unlock() from lock_task_sighand() to
unlock_task_sighand(). This way we can avoid preempt_disable too, but
I'd prefer to not do this.
Oleg.
next prev parent reply other threads:[~2014-09-22 19:14 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-09-22 16:44 [PATCH 0/2] signal: simplify/document lock_task_sighand() logic Oleg Nesterov
2014-09-22 16:44 ` [PATCH 1/2] signal: simplify deadlock-avoidance in lock_task_sighand() Oleg Nesterov
2014-09-22 18:58 ` Steven Rostedt
2014-09-22 19:11 ` Oleg Nesterov [this message]
2014-09-22 21:24 ` Steven Rostedt
2014-09-23 11:45 ` Rik van Riel
2014-09-23 14:20 ` Peter Zijlstra
2014-09-23 14:30 ` Steven Rostedt
2014-09-23 19:03 ` Oleg Nesterov
2014-09-24 8:36 ` Paul E. McKenney
2014-09-23 15:55 ` Peter Zijlstra
2014-09-22 16:44 ` [PATCH 2/2] signal: document the RCU protection of ->sighand Oleg Nesterov
2014-09-22 19:00 ` Steven Rostedt
2014-09-23 11:50 ` Rik van Riel
2014-09-28 21:43 ` [PATCH v2 0/2] document ->sighand protection, rcu_read_unlock() deadlocks Oleg Nesterov
2014-09-28 21:44 ` [PATCH v2 1/2] signal: document the RCU protection of ->sighand Oleg Nesterov
2014-09-28 21:44 ` [PATCH v2 2/2] rcu: more info about potential deadlocks with rcu_read_unlock() Oleg Nesterov
2014-10-23 19:56 ` [PATCH v2 0/2] document ->sighand protection, rcu_read_unlock() deadlocks Oleg Nesterov
2014-10-23 20:29 ` Paul E. McKenney
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20140922191130.GA4527@redhat.com \
--to=oleg@redhat.com \
--cc=akpm@linux-foundation.org \
--cc=linux-kernel@vger.kernel.org \
--cc=paulmck@linux.vnet.ibm.com \
--cc=peterz@infradead.org \
--cc=riel@redhat.com \
--cc=rostedt@goodmis.org \
--cc=tglx@linutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome