From: John Keeping <john@metanate.com>
To: Mark Yao <mark.yao@rock-chips.com>
Cc: Chris Zhong <zyw@rock-chips.com>,
dri-devel@lists.freedesktop.org,
linux-arm-kernel@lists.infradead.org,
linux-rockchip@lists.infradead.org, linux-kernel@vger.kernel.org,
John Keeping <john@metanate.com>
Subject: [PATCH v2 14/26] drm/rockchip: dw-mipi-dsi: fix escape clock rate
Date: Sat, 21 Jan 2017 16:31:16 +0000 [thread overview]
Message-ID: <20170121163128.22240-15-john@metanate.com> (raw)
In-Reply-To: <20170121163128.22240-1-john@metanate.com>
Use the same calculation as the vendor kernel to derive the escape clock
speed.
Signed-off-by: John Keeping <john@metanate.com>
---
Unchanged in v2
---
drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
index 290282e86d16..c2e0ba96e0a0 100644
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
@@ -710,11 +710,13 @@ static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi)
static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
{
+ u32 esc_clk_division = (dsi->lane_mbps >> 3) / 20 + 1;
+
dsi_write(dsi, DSI_PWR_UP, RESET);
dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK
| PHY_RSTZ | PHY_SHUTDOWNZ);
dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) |
- TX_ESC_CLK_DIVIDSION(7));
+ TX_ESC_CLK_DIVIDSION(esc_clk_division));
}
static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
--
2.11.0.197.gb556de5.dirty
next prev parent reply other threads:[~2017-01-21 16:35 UTC|newest]
Thread overview: 50+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-01-21 16:31 [PATCH v2 00/26] drm/rockchip: MIPI fixes & improvements John Keeping
2017-01-21 16:31 ` [PATCH v2 01/26] drm/rockchip: dw-mipi-dsi: don't configure hardware in mode_set for MIPI John Keeping
2017-01-22 3:58 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 02/26] drm/rockchip: dw-mipi-dsi: rename commit hook to enable John Keeping
2017-01-21 16:31 ` [PATCH v2 03/26] drm/rockchip: dw-mipi-dsi: pass mode in where needed John Keeping
2017-01-22 4:00 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 04/26] drm/rockchip: dw-mipi-dsi: remove mode_set hook John Keeping
2017-01-22 6:08 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 05/26] drm/rockchip: dw-mipi-dsi: fix command header writes John Keeping
2017-01-21 16:31 ` [PATCH v2 06/26] drm/rockchip: dw-mipi-dsi: fix generic packet status check John Keeping
2017-01-22 6:24 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 07/26] drm/rockchip: dw-mipi-dsi: avoid out-of-bounds read on tx_buf John Keeping
2017-01-22 6:42 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 08/26] drm/rockchip: dw-mipi-dsi: include bad value in error message John Keeping
2017-01-22 6:44 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 09/26] drm/rockchip: dw-mipi-dsi: respect message flags John Keeping
2017-01-22 7:14 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 10/26] drm/rockchip: dw-mipi-dsi: only request HS clock when required John Keeping
2017-01-22 8:10 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 11/26] drm/rockchip: dw-mipi-dsi: don't assume buffer is aligned John Keeping
2017-01-22 8:16 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 12/26] drm/rockchip: dw-mipi-dsi: prepare panel after phy init John Keeping
2017-01-22 8:22 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 13/26] drm/rockchip: dw-mipi-dsi: allow commands in panel_disable John Keeping
2017-01-22 8:37 ` Chris Zhong
2017-01-21 16:31 ` John Keeping [this message]
2017-01-22 9:37 ` [PATCH v2 14/26] drm/rockchip: dw-mipi-dsi: fix escape clock rate Chris Zhong
2017-01-21 16:31 ` [PATCH v2 15/26] drm/rockchip: dw-mipi-dsi: ensure PHY is reset John Keeping
2017-01-22 9:37 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 16/26] drm/rockchip: dw-mipi-dsi: configure bias and bandgap before enable John Keeping
2017-01-21 16:31 ` [PATCH v2 17/26] drm/rockchip: dw-mipi-dsi: don't enable PHY PLL until it's configured John Keeping
2017-01-22 10:07 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 18/26] drm/rockchip: dw-mipi-dsi: properly configure PHY timing John Keeping
2017-01-22 3:06 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 19/26] drm/rockchip: dw-mipi-dsi: improve PLL configuration John Keeping
2017-01-23 1:38 ` Chris Zhong
2017-01-23 12:49 ` John Keeping
2017-01-24 2:42 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 20/26] drm/rockchip: dw-mipi-dsi: use specific poll helper John Keeping
2017-01-23 0:49 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 21/26] drm/rockchip: dw-mipi-dsi: use positive check for N{H,V}SYNC John Keeping
2017-01-21 16:31 ` [PATCH v2 22/26] drm/rockchip: vop: test for P{H,V}SYNC John Keeping
2017-01-23 7:12 ` Mark yao
2017-01-21 16:31 ` [PATCH v2 23/26] drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded John Keeping
2017-01-21 16:31 ` [PATCH v2 24/26] drm/rockchip: dw-mipi-dsi: support non-burst modes John Keeping
2017-01-23 6:11 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 25/26] drm/rockchip: dw-mipi-dsi: add reset control John Keeping
2017-01-23 6:12 ` Chris Zhong
2017-01-21 16:31 ` [PATCH v2 26/26] drm/rockchip: dw-mipi-dsi: support read commands John Keeping
2017-01-22 3:08 ` Chris Zhong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170121163128.22240-15-john@metanate.com \
--to=john@metanate.com \
--cc=dri-devel@lists.freedesktop.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=mark.yao@rock-chips.com \
--cc=zyw@rock-chips.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome