[PATCH AUTOSEL for 3.18 01/24] mtd: nand: gpmi: Fix failure when a erased page has a bitflip at BBM

[PATCH AUTOSEL for 3.18 01/24] mtd: nand: gpmi: Fix failure when a erased page has a bitflip at BBM

[Sasha Levin]

From: Sascha Hauer <s.hauer@pengutronix.de>

[ Upstream commit fdf2e821052958a114618a95ab18a300d0b080cb ]

When erased subpages are read then the BCH decoder returns STATUS_ERASED
if they are all empty, or STATUS_UNCORRECTABLE if there are bitflips.
When there are bitflips, we have to set these bits again to show the
upper layers a completely erased page. When a bitflip happens in the
exact byte where the bad block marker is, then this byte is swapped
with another byte in block_mark_swapping(). The correction code then
detects a bitflip in another subpage and no longer corrects the bitflip
where it really happens.

Correct this behaviour by calling block_mark_swapping() after the
bitflips have been corrected.

In our case UBIFS failed with this bug because it expects erased
pages to be really empty:

UBIFS error (pid 187): ubifs_scan: corrupt empty space at LEB 36:118735
UBIFS error (pid 187): ubifs_scanned_corruption: corruption at LEB 36:118735
UBIFS error (pid 187): ubifs_scanned_corruption: first 8192 bytes from LEB 36:118735
UBIFS error (pid 187): ubifs_scan: LEB 36 scanning failed
UBIFS error (pid 187): do_commit: commit failed, error -117

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
index 959cb9b70310..0b27e338dae9 100644
--- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
+++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
@@ -1025,9 +1025,6 @@ static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip,
 		return ret;
 	}
 
-	/* handle the block mark swapping */
-	block_mark_swapping(this, payload_virt, auxiliary_virt);
-
 	/* Loop over status bytes, accumulating ECC status. */
 	status = auxiliary_virt + nfc_geo->auxiliary_status_offset;
 
@@ -1043,6 +1040,9 @@ static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip,
 		max_bitflips = max_t(unsigned int, max_bitflips, *status);
 	}
 
+	/* handle the block mark swapping */
+	block_mark_swapping(this, buf, auxiliary_virt);
+
 	if (oob_required) {
 		/*
 		 * It's time to deliver the OOB bytes. See gpmi_ecc_read_oob()
-- 
2.11.0

[PATCH AUTOSEL for 3.18 02/24] ipv6: icmp6: Allow icmp messages to be looped back

[Sasha Levin]

From: Brendan McGrath <redmcg@redmandi.dyndns.org>

[ Upstream commit 588753f1eb18978512b1c9b85fddb457d46f9033 ]

One example of when an ICMPv6 packet is required to be looped back is
when a host acts as both a Multicast Listener and a Multicast Router.

A Multicast Router will listen on address ff02::16 for MLDv2 messages.

Currently, MLDv2 messages originating from a Multicast Listener running
on the same host as the Multicast Router are not being delivered to the
Multicast Router. This is due to dst.input being assigned the default
value of dst_discard.

This results in the packet being looped back but discarded before being
delivered to the Multicast Router.

This patch sets dst.input to ip6_input to ensure a looped back packet
is delivered to the Multicast Router.

Signed-off-by: Brendan McGrath <redmcg@redmandi.dyndns.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 net/ipv6/route.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/ipv6/route.c b/net/ipv6/route.c
index 31ecdb35fd7f..168e40d98cce 100644
--- a/net/ipv6/route.c
+++ b/net/ipv6/route.c
@@ -1367,6 +1367,7 @@ struct dst_entry *icmp6_dst_alloc(struct net_device *dev,
 	}
 
 	rt->dst.flags |= DST_HOST;
+	rt->dst.input = ip6_input;
 	rt->dst.output  = ip6_output;
 	atomic_set(&rt->dst.__refcnt, 1);
 	rt->rt6i_gateway  = fl6->daddr;
-- 
2.11.0

[PATCH AUTOSEL for 3.18 03/24] mm,vmscan: Make unregister_shrinker() no-op if register_shrinker() failed.

[Sasha Levin]

From: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>

[ Upstream commit bb422a738f6566f7439cd347d54e321e4fe92a9f ]

Syzbot caught an oops at unregister_shrinker() because combination of
commit 1d3d4437eae1bb29 ("vmscan: per-node deferred work") and fault
injection made register_shrinker() fail and the caller of
register_shrinker() did not check for failure.

----------
[  554.881422] FAULT_INJECTION: forcing a failure.
[  554.881422] name failslab, interval 1, probability 0, space 0, times 0
[  554.881438] CPU: 1 PID: 13231 Comm: syz-executor1 Not tainted 4.14.0-rc8+ #82
[  554.881443] Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
[  554.881445] Call Trace:
[  554.881459]  dump_stack+0x194/0x257
[  554.881474]  ? arch_local_irq_restore+0x53/0x53
[  554.881486]  ? find_held_lock+0x35/0x1d0
[  554.881507]  should_fail+0x8c0/0xa40
[  554.881522]  ? fault_create_debugfs_attr+0x1f0/0x1f0
[  554.881537]  ? check_noncircular+0x20/0x20
[  554.881546]  ? find_next_zero_bit+0x2c/0x40
[  554.881560]  ? ida_get_new_above+0x421/0x9d0
[  554.881577]  ? find_held_lock+0x35/0x1d0
[  554.881594]  ? __lock_is_held+0xb6/0x140
[  554.881628]  ? check_same_owner+0x320/0x320
[  554.881634]  ? lock_downgrade+0x990/0x990
[  554.881649]  ? find_held_lock+0x35/0x1d0
[  554.881672]  should_failslab+0xec/0x120
[  554.881684]  __kmalloc+0x63/0x760
[  554.881692]  ? lock_downgrade+0x990/0x990
[  554.881712]  ? register_shrinker+0x10e/0x2d0
[  554.881721]  ? trace_event_raw_event_module_request+0x320/0x320
[  554.881737]  register_shrinker+0x10e/0x2d0
[  554.881747]  ? prepare_kswapd_sleep+0x1f0/0x1f0
[  554.881755]  ? _down_write_nest_lock+0x120/0x120
[  554.881765]  ? memcpy+0x45/0x50
[  554.881785]  sget_userns+0xbcd/0xe20
(...snipped...)
[  554.898693] kasan: CONFIG_KASAN_INLINE enabled
[  554.898724] kasan: GPF could be caused by NULL-ptr deref or user memory access
[  554.898732] general protection fault: 0000 [#1] SMP KASAN
[  554.898737] Dumping ftrace buffer:
[  554.898741]    (ftrace buffer empty)
[  554.898743] Modules linked in:
[  554.898752] CPU: 1 PID: 13231 Comm: syz-executor1 Not tainted 4.14.0-rc8+ #82
[  554.898755] Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
[  554.898760] task: ffff8801d1dbe5c0 task.stack: ffff8801c9e38000
[  554.898772] RIP: 0010:__list_del_entry_valid+0x7e/0x150
[  554.898775] RSP: 0018:ffff8801c9e3f108 EFLAGS: 00010246
[  554.898780] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
[  554.898784] RDX: 0000000000000000 RSI: ffff8801c53c6f98 RDI: ffff8801c53c6fa0
[  554.898788] RBP: ffff8801c9e3f120 R08: 1ffff100393c7d55 R09: 0000000000000004
[  554.898791] R10: ffff8801c9e3ef70 R11: 0000000000000000 R12: 0000000000000000
[  554.898795] R13: dffffc0000000000 R14: 1ffff100393c7e45 R15: ffff8801c53c6f98
[  554.898800] FS:  0000000000000000(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
[  554.898804] CS:  0010 DS: 002b ES: 002b CR0: 0000000080050033
[  554.898807] CR2: 00000000dbc23000 CR3: 00000001c7269000 CR4: 00000000001406e0
[  554.898813] DR0: 0000000020000000 DR1: 0000000020000000 DR2: 0000000000000000
[  554.898816] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000600
[  554.898818] Call Trace:
[  554.898828]  unregister_shrinker+0x79/0x300
[  554.898837]  ? perf_trace_mm_vmscan_writepage+0x750/0x750
[  554.898844]  ? down_write+0x87/0x120
[  554.898851]  ? deactivate_super+0x139/0x1b0
[  554.898857]  ? down_read+0x150/0x150
[  554.898864]  ? check_same_owner+0x320/0x320
[  554.898875]  deactivate_locked_super+0x64/0xd0
[  554.898883]  deactivate_super+0x141/0x1b0
----------

Since allowing register_shrinker() callers to call unregister_shrinker()
when register_shrinker() failed can simplify error recovery path, this
patch makes unregister_shrinker() no-op when register_shrinker() failed.
Also, reset shrinker->nr_deferred in case unregister_shrinker() was
by error called twice.

Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Aliaksei Karaliou <akaraliou.dev@gmail.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Glauber Costa <glauber@scylladb.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 mm/vmscan.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/mm/vmscan.c b/mm/vmscan.c
index d48b28219edf..6d652990433a 100644
--- a/mm/vmscan.c
+++ b/mm/vmscan.c
@@ -220,10 +220,13 @@ EXPORT_SYMBOL(register_shrinker);
  */
 void unregister_shrinker(struct shrinker *shrinker)
 {
+	if (!shrinker->nr_deferred)
+		return;
 	down_write(&shrinker_rwsem);
 	list_del(&shrinker->list);
 	up_write(&shrinker_rwsem);
 	kfree(shrinker->nr_deferred);
+	shrinker->nr_deferred = NULL;
 }
 EXPORT_SYMBOL(unregister_shrinker);
 
-- 
2.11.0

[PATCH AUTOSEL for 3.18 04/24] sget(): handle failures of register_shrinker()

[Sasha Levin]

From: Al Viro <viro@zeniv.linux.org.uk>

[ Upstream commit 9ee332d99e4d5a97548943b81c54668450ce641b ]

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 fs/super.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/fs/super.c b/fs/super.c
index 19fafe86071a..d4731c401278 100644
--- a/fs/super.c
+++ b/fs/super.c
@@ -476,7 +476,11 @@ retry:
 	hlist_add_head(&s->s_instances, &type->fs_supers);
 	spin_unlock(&sb_lock);
 	get_filesystem(type);
-	register_shrinker(&s->s_shrink);
+	err = register_shrinker(&s->s_shrink);
+	if (err) {
+		deactivate_locked_super(s);
+		s = ERR_PTR(err);
+	}
 	return s;
 }
 
-- 
2.11.0

[PATCH AUTOSEL for 3.18 06/24] net: arc_emac: fix arc_emac_rx() error paths

[Sasha Levin]

From: Alexander Kochetkov <al.kochet@gmail.com>

[ Upstream commit e688822d035b494071ecbadcccbd6f3325fb0f59 ]

arc_emac_rx() has some issues found by code review.

In case netdev_alloc_skb_ip_align() or dma_map_single() failure
rx fifo entry will not be returned to EMAC.

In case dma_map_single() failure previously allocated skb became
lost to driver. At the same time address of newly allocated skb
will not be provided to EMAC.

Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/net/ethernet/arc/emac_main.c | 53 +++++++++++++++++++++---------------
 1 file changed, 31 insertions(+), 22 deletions(-)

diff --git a/drivers/net/ethernet/arc/emac_main.c b/drivers/net/ethernet/arc/emac_main.c
index abe1eabc0171..9cc5daed13ed 100644
--- a/drivers/net/ethernet/arc/emac_main.c
+++ b/drivers/net/ethernet/arc/emac_main.c
@@ -250,39 +250,48 @@ static int arc_emac_rx(struct net_device *ndev, int budget)
 			continue;
 		}
 
-		pktlen = info & LEN_MASK;
-		stats->rx_packets++;
-		stats->rx_bytes += pktlen;
-		skb = rx_buff->skb;
-		skb_put(skb, pktlen);
-		skb->dev = ndev;
-		skb->protocol = eth_type_trans(skb, ndev);
-
-		dma_unmap_single(&ndev->dev, dma_unmap_addr(rx_buff, addr),
-				 dma_unmap_len(rx_buff, len), DMA_FROM_DEVICE);
-
-		/* Prepare the BD for next cycle */
-		rx_buff->skb = netdev_alloc_skb_ip_align(ndev,
-							 EMAC_BUFFER_SIZE);
-		if (unlikely(!rx_buff->skb)) {
+		/* Prepare the BD for next cycle. netif_receive_skb()
+		 * only if new skb was allocated and mapped to avoid holes
+		 * in the RX fifo.
+		 */
+		skb = netdev_alloc_skb_ip_align(ndev, EMAC_BUFFER_SIZE);
+		if (unlikely(!skb)) {
+			if (net_ratelimit())
+				netdev_err(ndev, "cannot allocate skb\n");
+			/* Return ownership to EMAC */
+			rxbd->info = cpu_to_le32(FOR_EMAC | EMAC_BUFFER_SIZE);
 			stats->rx_errors++;
-			/* Because receive_skb is below, increment rx_dropped */
 			stats->rx_dropped++;
 			continue;
 		}
 
-		/* receive_skb only if new skb was allocated to avoid holes */
-		netif_receive_skb(skb);
-
-		addr = dma_map_single(&ndev->dev, (void *)rx_buff->skb->data,
+		addr = dma_map_single(&ndev->dev, (void *)skb->data,
 				      EMAC_BUFFER_SIZE, DMA_FROM_DEVICE);
 		if (dma_mapping_error(&ndev->dev, addr)) {
 			if (net_ratelimit())
-				netdev_err(ndev, "cannot dma map\n");
-			dev_kfree_skb(rx_buff->skb);
+				netdev_err(ndev, "cannot map dma buffer\n");
+			dev_kfree_skb(skb);
+			/* Return ownership to EMAC */
+			rxbd->info = cpu_to_le32(FOR_EMAC | EMAC_BUFFER_SIZE);
 			stats->rx_errors++;
+			stats->rx_dropped++;
 			continue;
 		}
+
+		/* unmap previosly mapped skb */
+		dma_unmap_single(&ndev->dev, dma_unmap_addr(rx_buff, addr),
+				 dma_unmap_len(rx_buff, len), DMA_FROM_DEVICE);
+
+		pktlen = info & LEN_MASK;
+		stats->rx_packets++;
+		stats->rx_bytes += pktlen;
+		skb_put(rx_buff->skb, pktlen);
+		rx_buff->skb->dev = ndev;
+		rx_buff->skb->protocol = eth_type_trans(rx_buff->skb, ndev);
+
+		netif_receive_skb(rx_buff->skb);
+
+		rx_buff->skb = skb;
 		dma_unmap_addr_set(rx_buff, addr, addr);
 		dma_unmap_len_set(rx_buff, len, EMAC_BUFFER_SIZE);
 
-- 
2.11.0

[PATCH AUTOSEL for 3.18 05/24] spi: atmel: fixed spin_lock usage inside atmel_spi_remove

[Sasha Levin]

From: Radu Pirea <radu.pirea@microchip.com>

[ Upstream commit 66e900a3d225575c8b48b59ae1fe74bb6e5a65cc ]

The only part of atmel_spi_remove which needs to be atomic is hardware
reset.

atmel_spi_stop_dma calls dma_terminate_all and this needs interrupts
enabled.
atmel_spi_release_dma calls dma_release_channel and dma_release_channel
locks a mutex inside of spin_lock.

So the call of these functions can't be inside a spin_lock.

Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/spi/spi-atmel.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index 4bf337aa4fd5..fab124d3b8a6 100644
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -1416,12 +1416,12 @@ static int atmel_spi_remove(struct platform_device *pdev)
 	struct atmel_spi	*as = spi_master_get_devdata(master);
 
 	/* reset the hardware and block queue progress */
-	spin_lock_irq(&as->lock);
 	if (as->use_dma) {
 		atmel_spi_stop_dma(as);
 		atmel_spi_release_dma(as);
 	}
 
+	spin_lock_irq(&as->lock);
 	spi_writel(as, CR, SPI_BIT(SWRST));
 	spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */
 	spi_readl(as, SR);
-- 
2.11.0

[PATCH AUTOSEL for 3.18 07/24] scsi: storvsc: Fix scsi_cmd error assignments in storvsc_handle_error

[Sasha Levin]

From: Cathy Avery <cavery@redhat.com>

[ Upstream commit d1b8b2391c24751e44f618fcf86fb55d9a9247fd ]

When an I/O is returned with an srb_status of SRB_STATUS_INVALID_LUN
which has zero good_bytes it must be assigned an error. Otherwise the
I/O will be continuously requeued and will cause a deadlock in the case
where disks are being hot added and removed. sd_probe_async will wait
forever for its I/O to complete while holding scsi_sd_probe_domain.

Also returning the default error of DID_TARGET_FAILURE causes multipath
to not retry the I/O resulting in applications receiving I/O errors
before a failover can occur.

Signed-off-by: Cathy Avery <cavery@redhat.com>
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/scsi/storvsc_drv.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/storvsc_drv.c b/drivers/scsi/storvsc_drv.c
index e511e3406cfa..96c6e75bbfe6 100644
--- a/drivers/scsi/storvsc_drv.c
+++ b/drivers/scsi/storvsc_drv.c
@@ -1029,10 +1029,11 @@ static void storvsc_handle_error(struct vmscsi_request *vm_srb,
 		case TEST_UNIT_READY:
 			break;
 		default:
-			set_host_byte(scmnd, DID_TARGET_FAILURE);
+			set_host_byte(scmnd, DID_ERROR);
 		}
 		break;
 	case SRB_STATUS_INVALID_LUN:
+		set_host_byte(scmnd, DID_NO_CONNECT);
 		do_work = true;
 		process_err_fn = storvsc_remove_lun;
 		break;
-- 
2.11.0

[PATCH AUTOSEL for 3.18 09/24] tg3: Enable PHY reset in MTU change path for 5720

[Sasha Levin]

From: Siva Reddy Kallam <siva.kallam@broadcom.com>

[ Upstream commit e60ee41aaf898584205a6af5c996860d0fe6a836 ]

A customer noticed RX path hang when MTU is changed on the fly while
running heavy traffic with NCSI enabled for 5717 and 5719. Since 5720
belongs to same ASIC family, we observed same issue and same fix
could solve this problem for 5720.

Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/net/ethernet/broadcom/tg3.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index e0b446525f53..397bc868559b 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -14214,7 +14214,8 @@ static int tg3_change_mtu(struct net_device *dev, int new_mtu)
 	 */
 	if (tg3_asic_rev(tp) == ASIC_REV_57766 ||
 	    tg3_asic_rev(tp) == ASIC_REV_5717 ||
-	    tg3_asic_rev(tp) == ASIC_REV_5719)
+	    tg3_asic_rev(tp) == ASIC_REV_5719 ||
+	    tg3_asic_rev(tp) == ASIC_REV_5720)
 		reset_phy = true;
 
 	err = tg3_restart_hw(tp, reset_phy);
-- 
2.11.0

[PATCH AUTOSEL for 3.18 08/24] tg3: Add workaround to restrict 5762 MRRS to 2048

[Sasha Levin]

From: Siva Reddy Kallam <siva.kallam@broadcom.com>

[ Upstream commit 4419bb1cedcda0272e1dc410345c5a1d1da0e367 ]

One of AMD based server with 5762 hangs with jumbo frame traffic.
This AMD platform has southbridge limitation which is restricting MRRS
to 4000. As a work around, driver to restricts the MRRS to 2048 for
this particular 5762 NX1 card.

Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/net/ethernet/broadcom/tg3.c | 10 ++++++++++
 drivers/net/ethernet/broadcom/tg3.h |  4 ++++
 2 files changed, 14 insertions(+)

diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index 05a2f3b304c3..e0b446525f53 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -10028,6 +10028,16 @@ static int tg3_reset_hw(struct tg3 *tp, bool reset_phy)
 
 	tw32(GRC_MODE, tp->grc_mode | val);
 
+	/* On one of the AMD platform, MRRS is restricted to 4000 because of
+	 * south bridge limitation. As a workaround, Driver is setting MRRS
+	 * to 2048 instead of default 4096.
+	 */
+	if (tp->pdev->subsystem_vendor == PCI_VENDOR_ID_DELL &&
+	    tp->pdev->subsystem_device == TG3PCI_SUBDEVICE_ID_DELL_5762) {
+		val = tr32(TG3PCI_DEV_STATUS_CTRL) & ~MAX_READ_REQ_MASK;
+		tw32(TG3PCI_DEV_STATUS_CTRL, val | MAX_READ_REQ_SIZE_2048);
+	}
+
 	/* Setup the timer prescalar register.  Clock is always 66Mhz. */
 	val = tr32(GRC_MISC_CFG);
 	val &= ~0xff;
diff --git a/drivers/net/ethernet/broadcom/tg3.h b/drivers/net/ethernet/broadcom/tg3.h
index 31c9f8295953..19532961e173 100644
--- a/drivers/net/ethernet/broadcom/tg3.h
+++ b/drivers/net/ethernet/broadcom/tg3.h
@@ -95,6 +95,7 @@
 #define TG3PCI_SUBDEVICE_ID_DELL_JAGUAR		0x0106
 #define TG3PCI_SUBDEVICE_ID_DELL_MERLOT		0x0109
 #define TG3PCI_SUBDEVICE_ID_DELL_SLIM_MERLOT	0x010a
+#define TG3PCI_SUBDEVICE_ID_DELL_5762		0x07f0
 #define TG3PCI_SUBVENDOR_ID_COMPAQ		PCI_VENDOR_ID_COMPAQ
 #define TG3PCI_SUBDEVICE_ID_COMPAQ_BANSHEE	0x007c
 #define TG3PCI_SUBDEVICE_ID_COMPAQ_BANSHEE_2	0x009a
@@ -280,6 +281,9 @@
 #define TG3PCI_STD_RING_PROD_IDX	0x00000098 /* 64-bit */
 #define TG3PCI_RCV_RET_RING_CON_IDX	0x000000a0 /* 64-bit */
 /* 0xa8 --> 0xb8 unused */
+#define TG3PCI_DEV_STATUS_CTRL		0x000000b4
+#define  MAX_READ_REQ_SIZE_2048		 0x00004000
+#define  MAX_READ_REQ_MASK		 0x00007000
 #define TG3PCI_DUAL_MAC_CTRL		0x000000b8
 #define  DUAL_MAC_CTRL_CH_MASK		 0x00000003
 #define  DUAL_MAC_CTRL_ID		 0x00000004
-- 
2.11.0

[PATCH AUTOSEL for 3.18 10/24] bnx2x: Improve reliability in case of nested PCI errors

[Sasha Levin]

From: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>

[ Upstream commit f7084059a9cb9e56a186e1677b1dcffd76c2cd24 ]

While in recovery process of PCI error (called EEH on PowerPC arch),
another PCI transaction could be corrupted causing a situation of
nested PCI errors. Also, this scenario could be reproduced with
error injection mechanisms (for debug purposes).

We observe that in case of nested PCI errors, bnx2x might attempt to
initialize its shmem and cause a kernel crash due to bad addresses
read from MCP. Multiple different stack traces were observed depending
on the point the second PCI error happens.

This patch avoids the crashes by:

 * failing PCI recovery in case of nested errors (since multiple
 PCI errors in a row are not expected to lead to a functional
 adapter anyway), and by,

 * preventing access to adapter FW when MCP is failed (we mark it as
 failed when shmem cannot get initialized properly).

Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Shahed Shaikh <Shahed.Shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c  |  4 ++--
 drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 14 +++++++++++++-
 2 files changed, 15 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
index c4ad4b390239..d2ebc9d5e183 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
@@ -2994,7 +2994,7 @@ int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode, bool keep_link)
 
 	del_timer_sync(&bp->timer);
 
-	if (IS_PF(bp)) {
+	if (IS_PF(bp) && !BP_NOMCP(bp)) {
 		/* Set ALWAYS_ALIVE bit in shmem */
 		bp->fw_drv_pulse_wr_seq |= DRV_PULSE_ALWAYS_ALIVE;
 		bnx2x_drv_pulse(bp);
@@ -3076,7 +3076,7 @@ int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode, bool keep_link)
 	bp->cnic_loaded = false;
 
 	/* Clear driver version indication in shmem */
-	if (IS_PF(bp))
+	if (IS_PF(bp) && !BP_NOMCP(bp))
 		bnx2x_update_mng_version(bp);
 
 	/* Check if there are pending parity attentions. If there are - set
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
index 1217eafb61a4..f8e8206d7620 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -9472,6 +9472,15 @@ static int bnx2x_init_shmem(struct bnx2x *bp)
 
 	do {
 		bp->common.shmem_base = REG_RD(bp, MISC_REG_SHARED_MEM_ADDR);
+
+		/* If we read all 0xFFs, means we are in PCI error state and
+		 * should bail out to avoid crashes on adapter's FW reads.
+		 */
+		if (bp->common.shmem_base == 0xFFFFFFFF) {
+			bp->flags |= NO_MCP_FLAG;
+			return -ENODEV;
+		}
+
 		if (bp->common.shmem_base) {
 			val = SHMEM_RD(bp, validity_map[BP_PORT(bp)]);
 			if (val & SHR_MEM_VALIDITY_MB)
@@ -13743,7 +13752,10 @@ static pci_ers_result_t bnx2x_io_slot_reset(struct pci_dev *pdev)
 		BNX2X_ERR("IO slot reset --> driver unload\n");
 
 		/* MCP should have been reset; Need to wait for validity */
-		bnx2x_init_shmem(bp);
+		if (bnx2x_init_shmem(bp)) {
+			rtnl_unlock();
+			return PCI_ERS_RESULT_DISCONNECT;
+		}
 
 		if (IS_PF(bp) && SHMEM2_HAS(bp, drv_capabilities_flag)) {
 			u32 v;
-- 
2.11.0

[PATCH AUTOSEL for 3.18 12/24] s390/dasd: fix wrongly assigned configuration data

[Sasha Levin]

From: Stefan Haberland <sth@linux.vnet.ibm.com>

[ Upstream commit 8a9bd4f8ebc6800bfc0596e28631ff6809a2f615 ]

We store per path and per device configuration data to identify the
path or device correctly. The per path configuration data might get
mixed up if the original request gets into error recovery and is
started with a random path mask.

This would lead to a wrong identification of a path in case of a CUIR
event for example.

Fix by copying the path mask from the original request to the error
recovery request in case it is a path verification request.

Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/s390/block/dasd_3990_erp.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/s390/block/dasd_3990_erp.c b/drivers/s390/block/dasd_3990_erp.c
index d26134713682..d05c553eb552 100644
--- a/drivers/s390/block/dasd_3990_erp.c
+++ b/drivers/s390/block/dasd_3990_erp.c
@@ -2743,6 +2743,16 @@ dasd_3990_erp_action(struct dasd_ccw_req * cqr)
 		erp = dasd_3990_erp_handle_match_erp(cqr, erp);
 	}
 
+
+	/*
+	 * For path verification work we need to stick with the path that was
+	 * originally chosen so that the per path configuration data is
+	 * assigned correctly.
+	 */
+	if (test_bit(DASD_CQR_VERIFY_PATH, &erp->flags) && cqr->lpm) {
+		erp->lpm = cqr->lpm;
+	}
+
 	if (device->features & DASD_FEATURE_ERPLOG) {
 		/* print current erp_chain */
 		dev_err(&device->cdev->dev,
-- 
2.11.0

[PATCH AUTOSEL for 3.18 11/24] led: core: Fix brightness setting when setting delay_off=0

[Sasha Levin]

From: Matthieu CASTET <matthieu.castet@parrot.com>

[ Upstream commit 2b83ff96f51d0b039c4561b9f95c824d7bddb85c ]

With the current code, the following sequence won't work :
echo timer > trigger

echo 0 >  delay_off
* at this point we call
** led_delay_off_store
** led_blink_set
*** stop timer
** led_blink_setup
** led_set_software_blink
*** if !delay_on, led off
*** if !delay_off, set led_set_brightness_nosleep <--- LED_BLINK_SW is set but timer is stop
*** otherwise start timer/set LED_BLINK_SW flag

echo xxx > brightness
* led_set_brightness
** if LED_BLINK_SW
*** if brightness=0, led off
*** else apply brightness if next timer <--- timer is stop, and will never apply new setting
** otherwise set led_set_brightness_nosleep

To fix that, when we delete the timer, we should clear LED_BLINK_SW.

Cc: linux-leds@vger.kernel.org
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/leds/led-core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/leds/led-core.c b/drivers/leds/led-core.c
index aaa8eba9099f..0633cf033645 100644
--- a/drivers/leds/led-core.c
+++ b/drivers/leds/led-core.c
@@ -76,7 +76,7 @@ void led_blink_set(struct led_classdev *led_cdev,
 		   unsigned long *delay_on,
 		   unsigned long *delay_off)
 {
-	del_timer_sync(&led_cdev->blink_timer);
+	led_stop_software_blink(led_cdev);
 
 	led_cdev->flags &= ~LED_BLINK_ONESHOT;
 	led_cdev->flags &= ~LED_BLINK_ONESHOT_STOP;
-- 
2.11.0

[PATCH AUTOSEL for 3.18 14/24] xfs: quota: check result of register_shrinker()

[Sasha Levin]

From: Aliaksei Karaliou <akaraliou.dev@gmail.com>

[ Upstream commit 3a3882ff26fbdbaf5f7e13f6a0bccfbf7121041d ]

xfs_qm_init_quotainfo() does not check result of register_shrinker()
which was tagged as __must_check recently, reported by sparse.

Signed-off-by: Aliaksei Karaliou <akaraliou.dev@gmail.com>
[darrick: move xfs_qm_destroy_quotainos nearer xfs_qm_init_quotainos]
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>

Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 fs/xfs/xfs_qm.c | 45 +++++++++++++++++++++++++++++----------------
 1 file changed, 29 insertions(+), 16 deletions(-)

diff --git a/fs/xfs/xfs_qm.c b/fs/xfs/xfs_qm.c
index 30eea71405ce..b11a9c93e780 100644
--- a/fs/xfs/xfs_qm.c
+++ b/fs/xfs/xfs_qm.c
@@ -49,7 +49,7 @@
 STATIC int	xfs_qm_init_quotainos(xfs_mount_t *);
 STATIC int	xfs_qm_init_quotainfo(xfs_mount_t *);
 
-
+STATIC void	xfs_qm_destroy_quotainos(xfs_quotainfo_t *qi);
 STATIC void	xfs_qm_dqfree_one(struct xfs_dquot *dqp);
 /*
  * We use the batch lookup interface to iterate over the dquots as it
@@ -662,9 +662,17 @@ xfs_qm_init_quotainfo(
 	qinf->qi_shrinker.scan_objects = xfs_qm_shrink_scan;
 	qinf->qi_shrinker.seeks = DEFAULT_SEEKS;
 	qinf->qi_shrinker.flags = SHRINKER_NUMA_AWARE;
-	register_shrinker(&qinf->qi_shrinker);
+
+	error = register_shrinker(&qinf->qi_shrinker);
+	if (error)
+		goto out_free_inos;
+
 	return 0;
 
+out_free_inos:
+	mutex_destroy(&qinf->qi_quotaofflock);
+	mutex_destroy(&qinf->qi_tree_lock);
+	xfs_qm_destroy_quotainos(qinf);
 out_free_lru:
 	list_lru_destroy(&qinf->qi_lru);
 out_free_qinf:
@@ -673,7 +681,6 @@ out_free_qinf:
 	return error;
 }
 
-
 /*
  * Gets called when unmounting a filesystem or when all quotas get
  * turned off.
@@ -690,19 +697,7 @@ xfs_qm_destroy_quotainfo(
 
 	unregister_shrinker(&qi->qi_shrinker);
 	list_lru_destroy(&qi->qi_lru);
-
-	if (qi->qi_uquotaip) {
-		IRELE(qi->qi_uquotaip);
-		qi->qi_uquotaip = NULL; /* paranoia */
-	}
-	if (qi->qi_gquotaip) {
-		IRELE(qi->qi_gquotaip);
-		qi->qi_gquotaip = NULL;
-	}
-	if (qi->qi_pquotaip) {
-		IRELE(qi->qi_pquotaip);
-		qi->qi_pquotaip = NULL;
-	}
+	xfs_qm_destroy_quotainos(qi);
 	mutex_destroy(&qi->qi_tree_lock);
 	mutex_destroy(&qi->qi_quotaofflock);
 	kmem_free(qi);
@@ -1574,6 +1569,24 @@ error_rele:
 }
 
 STATIC void
+xfs_qm_destroy_quotainos(
+	xfs_quotainfo_t	*qi)
+{
+	if (qi->qi_uquotaip) {
+		IRELE(qi->qi_uquotaip);
+		qi->qi_uquotaip = NULL; /* paranoia */
+	}
+	if (qi->qi_gquotaip) {
+		IRELE(qi->qi_gquotaip);
+		qi->qi_gquotaip = NULL;
+	}
+	if (qi->qi_pquotaip) {
+		IRELE(qi->qi_pquotaip);
+		qi->qi_pquotaip = NULL;
+	}
+}
+
+STATIC void
 xfs_qm_dqfree_one(
 	struct xfs_dquot	*dqp)
 {
-- 
2.11.0

[PATCH AUTOSEL for 3.18 13/24] xfs: quota: fix missed destroy of qi_tree_lock

[Sasha Levin]

From: Aliaksei Karaliou <akaraliou.dev@gmail.com>

[ Upstream commit 2196881566225f3c3428d1a5f847a992944daa5b ]

xfs_qm_destroy_quotainfo() does not destroy quotainfo->qi_tree_lock
while destroys quotainfo->qi_quotaofflock.

Signed-off-by: Aliaksei Karaliou <akaraliou.dev@gmail.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 fs/xfs/xfs_qm.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/fs/xfs/xfs_qm.c b/fs/xfs/xfs_qm.c
index 2eb71027d236..30eea71405ce 100644
--- a/fs/xfs/xfs_qm.c
+++ b/fs/xfs/xfs_qm.c
@@ -703,6 +703,7 @@ xfs_qm_destroy_quotainfo(
 		IRELE(qi->qi_pquotaip);
 		qi->qi_pquotaip = NULL;
 	}
+	mutex_destroy(&qi->qi_tree_lock);
 	mutex_destroy(&qi->qi_quotaofflock);
 	kmem_free(qi);
 	mp->m_quotainfo = NULL;
-- 
2.11.0

[PATCH AUTOSEL for 3.18 15/24] e1000: fix disabling already-disabled warning

[Sasha Levin]

From: Tushar Dave <tushar.n.dave@oracle.com>

[ Upstream commit 0b76aae741abb9d16d2c0e67f8b1e766576f897d ]

This patch adds check so that driver does not disable already
disabled device.

[   44.637743] advantechwdt: Unexpected close, not stopping watchdog!
[   44.997548] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input6
[   45.013419] e1000 0000:00:03.0: disabling already-disabled device
[   45.013447] ------------[ cut here ]------------
[   45.014868] WARNING: CPU: 1 PID: 71 at drivers/pci/pci.c:1641 pci_disable_device+0xa1/0x105:
						pci_disable_device at drivers/pci/pci.c:1640
[   45.016171] CPU: 1 PID: 71 Comm: rcu_perf_shutdo Not tainted 4.14.0-01330-g3c07399 #1
[   45.017197] task: ffff88011bee9e40 task.stack: ffffc90000860000
[   45.017987] RIP: 0010:pci_disable_device+0xa1/0x105:
						pci_disable_device at drivers/pci/pci.c:1640
[   45.018603] RSP: 0000:ffffc90000863e30 EFLAGS: 00010286
[   45.019282] RAX: 0000000000000035 RBX: ffff88013a230008 RCX: 0000000000000000
[   45.020182] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000203
[   45.021084] RBP: ffff88013a3f31e8 R08: 0000000000000001 R09: 0000000000000000
[   45.021986] R10: ffffffff827ec29c R11: 0000000000000002 R12: 0000000000000001
[   45.022946] R13: ffff88013a230008 R14: ffff880117802b20 R15: ffffc90000863e8f
[   45.023842] FS:  0000000000000000(0000) GS:ffff88013fd00000(0000) knlGS:0000000000000000
[   45.024863] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   45.025583] CR2: ffffc900006d4000 CR3: 000000000220f000 CR4: 00000000000006a0
[   45.026478] Call Trace:
[   45.026811]  __e1000_shutdown+0x1d4/0x1e2:
						__e1000_shutdown at drivers/net/ethernet/intel/e1000/e1000_main.c:5162
[   45.027344]  ? rcu_perf_cleanup+0x2a1/0x2a1:
						rcu_perf_shutdown at kernel/rcu/rcuperf.c:627
[   45.027883]  e1000_shutdown+0x14/0x3a:
						e1000_shutdown at drivers/net/ethernet/intel/e1000/e1000_main.c:5235
[   45.028351]  device_shutdown+0x110/0x1aa:
						device_shutdown at drivers/base/core.c:2807
[   45.028858]  kernel_power_off+0x31/0x64:
						kernel_power_off at kernel/reboot.c:260
[   45.029343]  rcu_perf_shutdown+0x9b/0xa7:
						rcu_perf_shutdown at kernel/rcu/rcuperf.c:637
[   45.029852]  ? __wake_up_common_lock+0xa2/0xa2:
						autoremove_wake_function at kernel/sched/wait.c:376
[   45.030414]  kthread+0x126/0x12e:
						kthread at kernel/kthread.c:233
[   45.030834]  ? __kthread_bind_mask+0x8e/0x8e:
						kthread at kernel/kthread.c:190
[   45.031399]  ? ret_from_fork+0x1f/0x30:
						ret_from_fork at arch/x86/entry/entry_64.S:443
[   45.031883]  ? kernel_init+0xa/0xf5:
						kernel_init at init/main.c:997
[   45.032325]  ret_from_fork+0x1f/0x30:
						ret_from_fork at arch/x86/entry/entry_64.S:443
[   45.032777] Code: 00 48 85 ed 75 07 48 8b ab a8 00 00 00 48 8d bb 98 00 00 00 e8 aa d1 11 00 48 89 ea 48 89 c6 48 c7 c7 d8 e4 0b 82 e8 55 7d da ff <0f> ff b9 01 00 00 00 31 d2 be 01 00 00 00 48 c7 c7 f0 b1 61 82
[   45.035222] ---[ end trace c257137b1b1976ef ]---
[   45.037838] ACPI: Preparing to enter system sleep state S5

Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/net/ethernet/intel/e1000/e1000.h      |  3 ++-
 drivers/net/ethernet/intel/e1000/e1000_main.c | 27 ++++++++++++++++++++++-----
 2 files changed, 24 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000/e1000.h b/drivers/net/ethernet/intel/e1000/e1000.h
index 69707108d23c..4cd6dac110f0 100644
--- a/drivers/net/ethernet/intel/e1000/e1000.h
+++ b/drivers/net/ethernet/intel/e1000/e1000.h
@@ -328,7 +328,8 @@ struct e1000_adapter {
 enum e1000_state_t {
 	__E1000_TESTING,
 	__E1000_RESETTING,
-	__E1000_DOWN
+	__E1000_DOWN,
+	__E1000_DISABLED
 };
 
 #undef pr_fmt
diff --git a/drivers/net/ethernet/intel/e1000/e1000_main.c b/drivers/net/ethernet/intel/e1000/e1000_main.c
index 3a06cae4ff68..883d971c6cca 100644
--- a/drivers/net/ethernet/intel/e1000/e1000_main.c
+++ b/drivers/net/ethernet/intel/e1000/e1000_main.c
@@ -940,7 +940,7 @@ static int e1000_init_hw_struct(struct e1000_adapter *adapter,
 static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 {
 	struct net_device *netdev;
-	struct e1000_adapter *adapter;
+	struct e1000_adapter *adapter = NULL;
 	struct e1000_hw *hw;
 
 	static int cards_found = 0;
@@ -950,6 +950,7 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	u16 tmp = 0;
 	u16 eeprom_apme_mask = E1000_EEPROM_APME;
 	int bars, need_ioport;
+	bool disable_dev = false;
 
 	/* do not allocate ioport bars when not needed */
 	need_ioport = e1000_is_need_ioport(pdev);
@@ -1250,11 +1251,13 @@ err_mdio_ioremap:
 	iounmap(hw->ce4100_gbe_mdio_base_virt);
 	iounmap(hw->hw_addr);
 err_ioremap:
+	disable_dev = !test_and_set_bit(__E1000_DISABLED, &adapter->flags);
 	free_netdev(netdev);
 err_alloc_etherdev:
 	pci_release_selected_regions(pdev, bars);
 err_pci_reg:
-	pci_disable_device(pdev);
+	if (!adapter || disable_dev)
+		pci_disable_device(pdev);
 	return err;
 }
 
@@ -1272,6 +1275,7 @@ static void e1000_remove(struct pci_dev *pdev)
 	struct net_device *netdev = pci_get_drvdata(pdev);
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	struct e1000_hw *hw = &adapter->hw;
+	bool disable_dev;
 
 	e1000_down_and_stop(adapter);
 	e1000_release_manageability(adapter);
@@ -1290,9 +1294,11 @@ static void e1000_remove(struct pci_dev *pdev)
 		iounmap(hw->flash_address);
 	pci_release_selected_regions(pdev, adapter->bars);
 
+	disable_dev = !test_and_set_bit(__E1000_DISABLED, &adapter->flags);
 	free_netdev(netdev);
 
-	pci_disable_device(pdev);
+	if (disable_dev)
+		pci_disable_device(pdev);
 }
 
 /**
@@ -5137,7 +5143,8 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
 	if (netif_running(netdev))
 		e1000_free_irq(adapter);
 
-	pci_disable_device(pdev);
+	if (!test_and_set_bit(__E1000_DISABLED, &adapter->flags))
+		pci_disable_device(pdev);
 
 	return 0;
 }
@@ -5181,6 +5188,10 @@ static int e1000_resume(struct pci_dev *pdev)
 		pr_err("Cannot enable PCI device from suspend\n");
 		return err;
 	}
+
+	/* flush memory to make sure state is correct */
+	smp_mb__before_atomic();
+	clear_bit(__E1000_DISABLED, &adapter->flags);
 	pci_set_master(pdev);
 
 	pci_enable_wake(pdev, PCI_D3hot, 0);
@@ -5255,7 +5266,9 @@ static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
 
 	if (netif_running(netdev))
 		e1000_down(adapter);
-	pci_disable_device(pdev);
+
+	if (!test_and_set_bit(__E1000_DISABLED, &adapter->flags))
+		pci_disable_device(pdev);
 
 	/* Request a slot slot reset. */
 	return PCI_ERS_RESULT_NEED_RESET;
@@ -5283,6 +5296,10 @@ static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev)
 		pr_err("Cannot re-enable PCI device after reset.\n");
 		return PCI_ERS_RESULT_DISCONNECT;
 	}
+
+	/* flush memory to make sure state is correct */
+	smp_mb__before_atomic();
+	clear_bit(__E1000_DISABLED, &adapter->flags);
 	pci_set_master(pdev);
 
 	pci_enable_wake(pdev, PCI_D3hot, 0);
-- 
2.11.0

[PATCH AUTOSEL for 3.18 16/24] drm/ttm: check the return value of kzalloc

[Sasha Levin]

From: Xiongwei Song <sxwjean@gmail.com>

[ Upstream commit 19d859a7205bc59ffc38303eb25ae394f61d21dc ]

In the function ttm_page_alloc_init, kzalloc call is made for variable
_manager, we need to check its return value, it may return NULL.

Signed-off-by: Xiongwei Song <sxwjean@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/gpu/drm/ttm/ttm_page_alloc.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/gpu/drm/ttm/ttm_page_alloc.c b/drivers/gpu/drm/ttm/ttm_page_alloc.c
index 5d8dfe027b30..75d51ec98e06 100644
--- a/drivers/gpu/drm/ttm/ttm_page_alloc.c
+++ b/drivers/gpu/drm/ttm/ttm_page_alloc.c
@@ -818,6 +818,8 @@ int ttm_page_alloc_init(struct ttm_mem_global *glob, unsigned max_pages)
 	pr_info("Initializing pool allocator\n");
 
 	_manager = kzalloc(sizeof(*_manager), GFP_KERNEL);
+	if (!_manager)
+		return -ENOMEM;
 
 	ttm_page_pool_init_locked(&_manager->wc_pool, GFP_HIGHUSER, "wc");
 
-- 
2.11.0

[PATCH AUTOSEL for 3.18 17/24] loop: fix concurrent lo_open/lo_release

[Sasha Levin]

From: Linus Torvalds <torvalds@linux-foundation.org>

[ Upstream commit ae6650163c66a7eff1acd6eb8b0f752dcfa8eba5 ]

范龙飞 reports that KASAN can report a use-after-free in __lock_acquire.
The reason is due to insufficient serialization in lo_release(), which
will continue to use the loop device even after it has decremented the
lo_refcnt to zero.

In the meantime, another process can come in, open the loop device
again as it is being shut down. Confusion ensues.

Reported-by: 范龙飞 <long7573@126.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/block/loop.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/block/loop.c b/drivers/block/loop.c
index 6cb1beb47c25..94385b969f67 100644
--- a/drivers/block/loop.c
+++ b/drivers/block/loop.c
@@ -1512,9 +1512,8 @@ out:
 	return err;
 }
 
-static void lo_release(struct gendisk *disk, fmode_t mode)
+static void __lo_release(struct loop_device *lo)
 {
-	struct loop_device *lo = disk->private_data;
 	int err;
 
 	mutex_lock(&lo->lo_ctl_mutex);
@@ -1542,6 +1541,13 @@ out:
 	mutex_unlock(&lo->lo_ctl_mutex);
 }
 
+static void lo_release(struct gendisk *disk, fmode_t mode)
+{
+	mutex_lock(&loop_index_mutex);
+	__lo_release(disk->private_data);
+	mutex_unlock(&loop_index_mutex);
+}
+
 static const struct block_device_operations lo_fops = {
 	.owner =	THIS_MODULE,
 	.open =		lo_open,
-- 
2.11.0

[PATCH AUTOSEL for 3.18 19/24] mdio-sun4i: Fix a memory leak

[Sasha Levin]

From: Christophe JAILLET <christophe.jaillet@wanadoo.fr>

[ Upstream commit 56c0290202ab94a2f2780c449395d4ae8495fab4 ]

If the probing of the regulator is deferred, the memory allocated by
'mdiobus_alloc_size()' will be leaking.
It should be freed before the next call to 'sun4i_mdio_probe()' which will
reallocate it.

Fixes: 4bdcb1dd9feb ("net: Add MDIO bus driver for the Allwinner EMAC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/net/phy/mdio-sun4i.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/net/phy/mdio-sun4i.c b/drivers/net/phy/mdio-sun4i.c
index 15bc7f9ea224..afd76e07088b 100644
--- a/drivers/net/phy/mdio-sun4i.c
+++ b/drivers/net/phy/mdio-sun4i.c
@@ -128,8 +128,10 @@ static int sun4i_mdio_probe(struct platform_device *pdev)
 
 	data->regulator = devm_regulator_get(&pdev->dev, "phy");
 	if (IS_ERR(data->regulator)) {
-		if (PTR_ERR(data->regulator) == -EPROBE_DEFER)
-			return -EPROBE_DEFER;
+		if (PTR_ERR(data->regulator) == -EPROBE_DEFER) {
+			ret = -EPROBE_DEFER;
+			goto err_out_free_mdiobus;
+		}
 
 		dev_info(&pdev->dev, "no regulator found\n");
 	} else {
-- 
2.11.0

[PATCH AUTOSEL for 3.18 18/24] xen-netfront: enable device after manual module load

[Sasha Levin]

From: Eduardo Otubo <otubo@redhat.com>

[ Upstream commit b707fda2df4070785d0fa8a278aa13944c5f51f8 ]

When loading the module after unloading it, the network interface would
not be enabled and thus wouldn't have a backend counterpart and unable
to be used by the guest.

The guest would face errors like:

  [root@guest ~]# ethtool -i eth0
  Cannot get driver information: No such device

  [root@guest ~]# ifconfig eth0
  eth0: error fetching interface information: Device not found

This patch initializes the state of the netfront device whenever it is
loaded manually, this state would communicate the netback to create its
device and establish the connection between them.

Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/net/xen-netfront.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/xen-netfront.c b/drivers/net/xen-netfront.c
index 8f45be1592ca..8fe7099519c9 100644
--- a/drivers/net/xen-netfront.c
+++ b/drivers/net/xen-netfront.c
@@ -1356,6 +1356,7 @@ static struct net_device *xennet_create_dev(struct xenbus_device *dev)
 
 	netif_carrier_off(netdev);
 
+	xenbus_switch_state(dev, XenbusStateInitialising);
 	return netdev;
 
  exit:
-- 
2.11.0

[PATCH AUTOSEL for 3.18 21/24] xen/gntdev: Fix off-by-one error when unmapping with holes

[Sasha Levin]

From: Ross Lagerwall <ross.lagerwall@citrix.com>

[ Upstream commit 951a010233625b77cde3430b4b8785a9a22968d1 ]

If the requested range has a hole, the calculation of the number of
pages to unmap is off by one. Fix it.

Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/xen/gntdev.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/xen/gntdev.c b/drivers/xen/gntdev.c
index 91cc44611062..1c03e30f66b4 100644
--- a/drivers/xen/gntdev.c
+++ b/drivers/xen/gntdev.c
@@ -348,10 +348,8 @@ static int unmap_grant_pages(struct grant_map *map, int offset, int pages)
 		}
 		range = 0;
 		while (range < pages) {
-			if (map->unmap_ops[offset+range].handle == -1) {
-				range--;
+			if (map->unmap_ops[offset+range].handle == -1)
 				break;
-			}
 			range++;
 		}
 		err = __unmap_grant_pages(map, offset, range);
-- 
2.11.0

[PATCH AUTOSEL for 3.18 20/24] SolutionEngine771x: fix Ether platform data

[Sasha Levin]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

[ Upstream commit 195e2addbce09e5afbc766efc1e6567c9ce840d3 ]

The 'sh_eth' driver's probe() method would fail  on the SolutionEngine7710
board and crash on SolutionEngine7712 board  as the platform code is
hopelessly behind the driver's platform data --  it passes the PHY address
instead of 'struct sh_eth_plat_data *'; pass the latter to the driver in
order to fix the bug...

Fixes: 71557a37adb5 ("[netdrvr] sh_eth: Add SH7619 support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 arch/sh/boards/mach-se/770x/setup.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/arch/sh/boards/mach-se/770x/setup.c b/arch/sh/boards/mach-se/770x/setup.c
index 658326f44df8..5e0267624d8d 100644
--- a/arch/sh/boards/mach-se/770x/setup.c
+++ b/arch/sh/boards/mach-se/770x/setup.c
@@ -8,6 +8,7 @@
  */
 #include <linux/init.h>
 #include <linux/platform_device.h>
+#include <linux/sh_eth.h>
 #include <mach-se/mach/se.h>
 #include <mach-se/mach/mrshpc.h>
 #include <asm/machvec.h>
@@ -114,6 +115,11 @@ static struct platform_device heartbeat_device = {
 #if defined(CONFIG_CPU_SUBTYPE_SH7710) ||\
 	defined(CONFIG_CPU_SUBTYPE_SH7712)
 /* SH771X Ethernet driver */
+static struct sh_eth_plat_data sh_eth_plat = {
+	.phy = PHY_ID,
+	.phy_interface = PHY_INTERFACE_MODE_MII,
+};
+
 static struct resource sh_eth0_resources[] = {
 	[0] = {
 		.start = SH_ETH0_BASE,
@@ -131,7 +137,7 @@ static struct platform_device sh_eth0_device = {
 	.name = "sh771x-ether",
 	.id = 0,
 	.dev = {
-		.platform_data = PHY_ID,
+		.platform_data = &sh_eth_plat,
 	},
 	.num_resources = ARRAY_SIZE(sh_eth0_resources),
 	.resource = sh_eth0_resources,
@@ -154,7 +160,7 @@ static struct platform_device sh_eth1_device = {
 	.name = "sh771x-ether",
 	.id = 1,
 	.dev = {
-		.platform_data = PHY_ID,
+		.platform_data = &sh_eth_plat,
 	},
 	.num_resources = ARRAY_SIZE(sh_eth1_resources),
 	.resource = sh_eth1_resources,
-- 
2.11.0

[PATCH AUTOSEL for 3.18 23/24] sctp: make use of pre-calculated len

[Sasha Levin]

From: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>

[ Upstream commit c76f97c99ae6d26d14c7f0e50e074382bfbc9f98 ]

Some sockopt handling functions were calculating the length of the
buffer to be written to userspace and then calculating it again when
actually writing the buffer, which could lead to some write not using
an up-to-date length.

This patch updates such places to just make use of the len variable.

Also, replace some sizeof(type) to sizeof(var).

Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 net/sctp/socket.c | 16 ++++++++++------
 1 file changed, 10 insertions(+), 6 deletions(-)

diff --git a/net/sctp/socket.c b/net/sctp/socket.c
index 06d9626a1678..225019397bc6 100644
--- a/net/sctp/socket.c
+++ b/net/sctp/socket.c
@@ -4458,7 +4458,7 @@ static int sctp_getsockopt_autoclose(struct sock *sk, int len, char __user *optv
 	len = sizeof(int);
 	if (put_user(len, optlen))
 		return -EFAULT;
-	if (copy_to_user(optval, &sctp_sk(sk)->autoclose, sizeof(int)))
+	if (copy_to_user(optval, &sctp_sk(sk)->autoclose, len))
 		return -EFAULT;
 	return 0;
 }
@@ -5035,6 +5035,9 @@ copy_getaddrs:
 		err = -EFAULT;
 		goto out;
 	}
+	/* XXX: We should have accounted for sizeof(struct sctp_getaddrs) too,
+	 * but we can't change it anymore.
+	 */
 	if (put_user(bytes_copied, optlen))
 		err = -EFAULT;
 out:
@@ -5471,7 +5474,7 @@ static int sctp_getsockopt_maxseg(struct sock *sk, int len,
 		params.assoc_id = 0;
 	} else if (len >= sizeof(struct sctp_assoc_value)) {
 		len = sizeof(struct sctp_assoc_value);
-		if (copy_from_user(&params, optval, sizeof(params)))
+		if (copy_from_user(&params, optval, len))
 			return -EFAULT;
 	} else
 		return -EINVAL;
@@ -5635,7 +5638,9 @@ static int sctp_getsockopt_active_key(struct sock *sk, int len,
 
 	if (len < sizeof(struct sctp_authkeyid))
 		return -EINVAL;
-	if (copy_from_user(&val, optval, sizeof(struct sctp_authkeyid)))
+
+	len = sizeof(struct sctp_authkeyid);
+	if (copy_from_user(&val, optval, len))
 		return -EFAULT;
 
 	asoc = sctp_id2assoc(sk, val.scact_assoc_id);
@@ -5647,7 +5652,6 @@ static int sctp_getsockopt_active_key(struct sock *sk, int len,
 	else
 		val.scact_keynumber = ep->active_key_id;
 
-	len = sizeof(struct sctp_authkeyid);
 	if (put_user(len, optlen))
 		return -EFAULT;
 	if (copy_to_user(optval, &val, len))
@@ -5673,7 +5677,7 @@ static int sctp_getsockopt_peer_auth_chunks(struct sock *sk, int len,
 	if (len < sizeof(struct sctp_authchunks))
 		return -EINVAL;
 
-	if (copy_from_user(&val, optval, sizeof(struct sctp_authchunks)))
+	if (copy_from_user(&val, optval, sizeof(val)))
 		return -EFAULT;
 
 	to = p->gauth_chunks;
@@ -5718,7 +5722,7 @@ static int sctp_getsockopt_local_auth_chunks(struct sock *sk, int len,
 	if (len < sizeof(struct sctp_authchunks))
 		return -EINVAL;
 
-	if (copy_from_user(&val, optval, sizeof(struct sctp_authchunks)))
+	if (copy_from_user(&val, optval, sizeof(val)))
 		return -EFAULT;
 
 	to = p->gauth_chunks;
-- 
2.11.0

[PATCH AUTOSEL for 3.18 22/24] xen/gntdev: Fix partial gntdev_mmap() cleanup

[Sasha Levin]

From: Ross Lagerwall <ross.lagerwall@citrix.com>

[ Upstream commit cf2acf66ad43abb39735568f55e1f85f9844e990 ]

When cleaning up after a partially successful gntdev_mmap(), unmap the
successfully mapped grant pages otherwise Xen will kill the domain if
in debug mode (Attempt to implicitly unmap a granted PTE) or Linux will
kill the process and emit "BUG: Bad page map in process" if Xen is in
release mode.

This is only needed when use_ptemod is true because gntdev_put_map()
will unmap grant pages itself when use_ptemod is false.

Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/xen/gntdev.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/xen/gntdev.c b/drivers/xen/gntdev.c
index 1c03e30f66b4..5ad2534480ff 100644
--- a/drivers/xen/gntdev.c
+++ b/drivers/xen/gntdev.c
@@ -817,8 +817,10 @@ unlock_out:
 out_unlock_put:
 	mutex_unlock(&priv->lock);
 out_put_map:
-	if (use_ptemod)
+	if (use_ptemod) {
 		map->vma = NULL;
+		unmap_grant_pages(map, 0, map->count);
+	}
 	gntdev_put_map(priv, map);
 	return err;
 }
-- 
2.11.0

[PATCH AUTOSEL for 3.18 24/24] net: gianfar_ptp: move set_fipers() to spinlock protecting area

[Sasha Levin]

From: Yangbo Lu <yangbo.lu@nxp.com>

[ Upstream commit 11d827a993a969c3c6ec56758ff63a44ba19b466 ]

set_fipers() calling should be protected by spinlock in
case that any interrupt breaks related registers setting
and the function we expect. This patch is to move set_fipers()
to spinlock protecting area in ptp_gianfar_adjtime().

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/net/ethernet/freescale/gianfar_ptp.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/freescale/gianfar_ptp.c b/drivers/net/ethernet/freescale/gianfar_ptp.c
index bb568006f37d..503991823551 100644
--- a/drivers/net/ethernet/freescale/gianfar_ptp.c
+++ b/drivers/net/ethernet/freescale/gianfar_ptp.c
@@ -314,11 +314,10 @@ static int ptp_gianfar_adjtime(struct ptp_clock_info *ptp, s64 delta)
 	now = tmr_cnt_read(etsects);
 	now += delta;
 	tmr_cnt_write(etsects, now);
+	set_fipers(etsects);
 
 	spin_unlock_irqrestore(&etsects->lock, flags);
 
-	set_fipers(etsects);
-
 	return 0;
 }
 
-- 
2.11.0